RB886Y Diodes Schottky barrier diode RB886Y zApplications High frequency detection zExternal dimensions (Unit : mm) zLand size figure (Unit : mm) 0.45 0.5 1.6±0.1 0.22±0.05 (3) 1.2±0.1 (4) (1) zConstruction Silicon epitaxial planar 0.5 1.55 0.13±0.05 1.0 1.6±0.1 zFeatures 1) Ultra small mold type. (EMD4) 2) Low Ct and high detection efficiency. 0～0.1 EMD4 (2) zStructure 0.5 1.0±0.1 0.5±0.05 ROHM : EMD4 JEITA : SC-75A Size dot (year week factory) zTaping specifications (Unit : mm) φ1.5±0.1 0 2.0±0.05 0.3±0.1 1PIN zAbsolute maximum ratings (Ta=25°C) Parameter Symbol Reverse voltage VR Forward current IF Junction temperature Tj Storage temperature Tstg 8.0±0.2 1.65±0.01 φ0.8±0.1 4.0±0.1 0～0.1 1.65±0.1 1.65±0.1 5.5±0.2 3.5±0.05 1.75±0.1 4.0±0.1 0.65±0.1 Limits 15 10 125 -40 to +125 Unit V mA ℃ ℃ (*1) Rate of per diode zElectrical characteristics (Ta=25°C) Parameter Symbol VF Min. - Typ. - Max. 0.35 Unit V Reverse currnt IR - - 120 µA Capacitance between terminals Ct - 0.53 0.80 pF Forward voltage Conditions IF=1mA VR=5V VR=1.0V , f=1MHz 1/2 RB886Y Diodes zElectrical characteristic curves (Ta=25°C) 10 1 1000 f=1MHz 1 Ta=-25℃ Ta=25℃ Ta=75℃ 0.1 Ta=125℃ 100 Ta=75℃ 10 Ta=-25℃ Ta=25℃ 0.01 300 600 900 1200 FORWARD VOLTAGE：VF(mV) VF-IF CHARACTERISTICS 1500 0 300 1 2 3 4 REVERSE VOLTAGE：VR(V) VR-IR CHARACTERISTICS 280 270 260 250 200 150 100 AVE:21.63uA 50 AVE:275.2mV VF DISPERSION MAP time Rth(j-a) 100 Rth(j-c) 0.5 0.4 0.3 0.2 AVE:0.520pF Ct DISPERSION MAP 4 3 AVE:1.47kV 2 AVE:0.48kV 1 0 0.01 0.6 5 300us 10 0.001 0.7 IF=100mA ELECTROSTATIC DDISCHARGE TEST ESD(KV) 1000 1ms 0.8 0 IR DISPERSION MAP Mounted on epoxy board IM=10mA 5 Ta=25℃ f=1MHz VR=1V n=10pcs 0.9 0.1 0 250 1 2 3 4 REVERSE VOLTAGE:VR(V) VR-Ct CHARACTERISTICS 1 Ta=25℃ VR=5V n=30pcs CAPACITANCE BETWEEN TERMINALS:Ct(pF) 290 10000 0 5 300 Ta=25℃ IF=1mA n=30pcs REVERSE CURRENT:IR(uA) FORWARD VOLTAGE:VF(mV) 0.1 1 0 TRANSIENT THAERMAL IMPEDANCE:Rth (℃/W) CAPACITANCE BETWEEN TERMINALS:Ct(pF) REVERSE CURRENT:IR(uA) FORWARD CURRENT:IF(mA) Ta=125℃ 0.1 1 10 100 TIME:t(s) Rth-t CHARACTERISTICS 1000 C=200pF R=0Ω C=100pF R=1.5kΩ ESD DISPERSION MAP 2/2 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1