AD7175-2 - Analog Devices

24-Bit, 250 kSPS, Sigma-Delta ADC with
20 µs Settling and True Rail-to-Rail Buffers
AD7175-2
Data Sheet
FEATURES
GENERAL DESCRIPTION
Fast and flexible output rate: 5 SPS to 250 kSPS
Channel scan data rate of 50 kSPS/channel (20 µs settling)
Performance specifications
17.2 noise free bits at 250 kSPS
20 noise free bits at 2.5 kSPS
24 noise free bits at 20 SPS
INL: ±1 ppm of FSR
85 dB rejection of 50 Hz and 60 Hz with 50 ms settling
User configurable input channels
2 fully differential channels or 4 single-ended channels
Crosspoint multiplexer
On-chip 2.5 V reference (±2 ppm/°C drift)
True rail-to-rail analog and reference input buffers
Internal or external clock
Power supply: AVDD1 = 5 V, AVDD2 = IOVDD = 2 V to 5 V
Split supply with AVDD1/AVSS at ±2.5 V
ADC current: 8.4 mA
Temperature range: −40°C to +105°C
3- or 4-wire serial digital interface (Schmitt trigger on SCLK)
Serial port interface (SPI), QSPI, MICROWIRE, and DSP
compatible
The AD7175-2 is a low noise, fast settling, multiplexed, 2-/4channel (fully/pseudo differential) Σ-Δ analog-to-digital
converter (ADC) for low bandwidth inputs. It has a maximum
channel scan rate of 50 kSPS (20 µs) for fully settled data. The
output data rates range from 5 SPS to 250 kSPS.
APPLICATIONS
The device operates with a 5 V AVDD1, or ±2.5 V AVDD1/AVSS,
and 2 V to 5 V AVDD2 and IOVDD supplies. The specified
operating temperature range is −40°C to +105°C. The AD7175-2 is
in a 24-lead TSSOP package.
The AD7175-2 integrates key analog and digital signal conditioning blocks to allow users to configure an individual setup for
each analog input channel in use. Each feature can be user selected
on a per channel basis. Integrated true rail-to-rail buffers on the
analog inputs and external reference inputs provide easy to drive
high impedance inputs. The precision 2.5 V low drift (2 ppm/°C)
band gap internal reference (with output reference buffer) adds
embedded functionality to reduce external component count.
The digital filter allows simultaneous 50 Hz/60 Hz rejection at
27.27 SPS output data rate. The user can switch between
different filter options according to the demands of each
channel in the application. The ADC automatically switches
through each selected channel. Further digital processing
functions include offset and gain calibration registers,
configurable on a per channel basis.
Process control: PLC/DCS modules
Temperature and pressure measurement
Medical and scientific multichannel instrumentation
Chromatography
Note that, throughout this data sheet, the dual function pin
names are referenced by the relevant function only.
FUNCTIONAL BLOCK DIAGRAM
AVDD1
CROSSPOINT
MULTIPLEXER
AIN0
AVDD2 REGCAPA
RAIL-TO-RAIL
REFERENCE
INPUT BUFFERS
1.8V
LDO
AVDD
AIN1
IOVDD REGCAPD
REF– REF+ REFOUT
BUFFERED
PRECISION
REFERENCE
1.8V
LDO
INT
REF
RAIL-TO-RAIL
ANALOG INPUT
BUFFERS
CS
DIGITAL
FILTER
Σ-Δ ADC
AIN2
SERIAL
INTERFACE
AND CONTROL
SCLK
DIN
DOUT/RDY
AIN3
SYNC/ERROR
XTAL AND INTERNAL
CLOCK OSCILLATOR
CIRCUITRY
AD7175-2
TEMPERATURE
SENSOR
AVSS
GPIO0 GPIO1
XTAL1 XTAL2/CLKIO
DGND
12468-001
AIN4
GPIO AND
MUX
I/O CONTROL
AVSS
Figure 1.
Rev. A
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
©2014 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
Powered by TCPDF (www.tcpdf.org)
IMPORTANT LINKS for the AD7175-2*
Last content update 10/03/2014 03:57 pm
SUGGESTED COMPANION PRODUCTS
DESIGN TOOLS, MODELS, DRIVERS & SOFTWARE
Recommended Driver Amplifiers for the AD7175-2
AD7175-2 IBIS Model
For a single supply, low noise, low distortion, fully chopped,
differential driver, we recommend the ADA4528-1 or
ADA4528-2.
For a single supply, attenuating input stage, differential driver,
we recommend the AD8475.
For additional driver amplifier selections, we recommend
selecting the product category and filtering on our parametric
search tables.
SIMILAR PRODUCTS & PARAMETRIC SELECTION TABLES
Find Similar Products By Operating Parameters
Recommended External Voltage References for the AD7175-2
For the family of low noise, low drift and high accuracy
references, we recommend the ADR445 or the ADR4550.
For additional voltage reference selections, we recommend
filtering on our parametric search tables.
Recommended Digital Isolators for the AD7175-2
For SPI Interface, lowest power, 2.5 kVrms isolation, we
recommend the ADuM1401.
For SPI Interface, enhanced system-level ESD performance, 2.5
kVrms isolation, we recommend the ADuM3401.
For SPI Interface, low power, 5.0 kVrms isolation, we
recommend the ADuM4401.
For SPI Interface, smallest package, low voltage I/O (1.8 V to 5.5
V), we recommend the ADuM3481.
For additional digital isolator selections, we recommend
filtering on our parametric search tables.
EVALUATION KITS & SYMBOLS & FOOTPRINTS
Symbols and Footprints
DESIGN COLLABORATION COMMUNITY
Collaborate Online with the ADI support team and other designers
about select ADI products.
Follow us on Twitter: www.twitter.com/ADI_News
Like us on Facebook: www.facebook.com/AnalogDevicesInc
Recommended External Multiplexers for the AD7175-2
For low Ron, 4:1 channel multiplexer, we recommend the
ADG1404.
For low Ron with four differential inputs, we recommend the
ADG1409.
For Fault Detection and Protection family with +/-55OV
protection, we recommend the ADG5412F.
For additional multiplexer selections, we recommend selecting
the product category and filtering on our parametric search
tables.
Recommended Power Solutions for the AD7175-2
For high input voltage LDO, we recommend the ADP7118 and
ADP7182.
For a charge-pump voltage converter, we recommend the
ADG1404.
DESIGN SUPPORT
Submit your support request here:
Linear and Data Converters
Embedded Processing and DSP
Telephone our Customer Interaction Centers toll free:
Americas:
Europe:
China:
India:
Russia:
1-800-262-5643
00800-266-822-82
4006-100-006
1800-419-0108
8-800-555-45-90
Quality and Reliability
Lead(Pb)-Free Data
Package Information
SAMPLE & BUY
AD7175-2
View Price & Packaging
Request Evaluation Board
Request Samples
Check Inventory & Purchase
Find Local Distributors
* This page was dynamically generated by Analog Devices, Inc. and inserted into this data sheet.
Note: Dynamic changes to the content on this page (labeled 'Important Links') does not
constitute a change to the revision number of the product data sheet.
This content may be frequently modified.
AD7175-2
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1 Checksum Protection ................................................................ 41 Applications ....................................................................................... 1 CRC Calculation......................................................................... 42 General Description ......................................................................... 1 Integrated Functions ...................................................................... 44 Functional Block Diagram .............................................................. 1 General-Purpose I/O ................................................................. 44 Revision History ............................................................................... 2 External Multiplexer Control ................................................... 44 Specifications..................................................................................... 3 Delay ............................................................................................ 44 Timing Characteristics ................................................................ 6 16-Bit/24-Bit Conversions......................................................... 44 Timing Diagrams.......................................................................... 7 DOUT_RESET ........................................................................... 44 Absolute Maximum Ratings............................................................ 8 Synchronization .......................................................................... 44 Thermal Resistance ...................................................................... 8 Error Flags ................................................................................... 45 ESD Caution .................................................................................. 8 DATA_STAT ............................................................................... 45 Pin Configuration and Function Descriptions ............................. 9 IOSTRENGTH ........................................................................... 46 Typical Performance Characteristics ........................................... 11 Internal Temperature Sensor .................................................... 46 Noise Performance and Resolution .............................................. 18 Grounding and Layout .................................................................. 47 Getting Started ................................................................................ 19 Register Summary .......................................................................... 48 Power Supplies ............................................................................ 20 Register Details ............................................................................... 49 Digital Communication............................................................. 20 Communications Register ......................................................... 49 AD7175-2 Reset .......................................................................... 21 Status Register ............................................................................. 50 Configuration Overview ........................................................... 21 ADC Mode Register ................................................................... 51 Circuit Description ......................................................................... 26 Interface Mode Register ............................................................ 52 Buffered Analog Input ............................................................... 26 Register Check ............................................................................ 53 Crosspoint Multiplexer .............................................................. 26 Data Register ............................................................................... 53 AD7175-2 Reference .................................................................. 27 GPIO Configuration Register ................................................... 54 Buffered Reference Input........................................................... 28 ID Register................................................................................... 55 Clock Source ............................................................................... 28 Channel Register 0 ..................................................................... 55 Digital Filters ................................................................................... 29 Channel Register 1 to Channel Register 3 .............................. 56 Sinc5 + Sinc1 Filter..................................................................... 29 Setup Configuration Register 0 ................................................ 57 Sinc3 Filter ................................................................................... 29 Setup Configuration Register 1 to Setup Configuration
Register 3 ..................................................................................... 57 Single Cycle Settling ................................................................... 30 Enhanced 50 Hz and 60 Hz Rejection Filters ......................... 34 Filter Configuration Register 0 ................................................. 58 Operating Modes ............................................................................ 37 Filter Configuration Register 1 to Filter Configuration
Register 3 ..................................................................................... 59 Continuous Conversion Mode ................................................. 37 Offset Register 0 ......................................................................... 59 Continuous Read Mode ............................................................. 38 Offset Register 1 to Offset Register 3 ....................................... 59 Single Conversion Mode ........................................................... 39 Gain Register 0............................................................................ 59 Standby and Power-Down Modes ............................................ 40 Gain Register 1 to Gain Register 3 ........................................... 59 Calibration ................................................................................... 40 Outline Dimensions ....................................................................... 60 Digital Interface .............................................................................. 41 Ordering Guide .......................................................................... 60 REVISION HISTORY
9/14—Rev. 0 to Rev. A
Changes to Ordering Guide .......................................................... 60
7/14—Revision 0: Initial Version
Rev. A | Page 2 of 60
Data Sheet
AD7175-2
SPECIFICATIONS
AVDD1 = 4.5 V to 5.5 V, AVDD2 = 2 V to 5.5 V, IOVDD = 2 V to 5.5 V, AVSS = DGND = 0 V, REF+ = 2.5 V, REF− = AVSS,
MCLK = internal master clock = 16 MHz, TA = TMIN to TMAX (−40°C to +105°C), unless otherwise noted.
Table 1.
Parameter
ADC SPEED AND PERFORMANCE
Output Data Rate (ODR)
No Missing Codes1
Resolution
Noise
ACCURACY
Integral Nonlinearity (INL)
Offset Error2
Offset Drift
Gain Error2
Gain Drift
REJECTION
Power Supply Rejection
Common-Mode Rejection
At DC
At 50 Hz, 60 Hz1
Normal Mode Rejection1
ANALOG INPUTS
Differential Input Range
Absolute Voltage Limits1
Input Buffers Disabled
Input Buffers Enabled
Analog Input Current
Input Buffers Disabled
Input Current
Input Current Drift
Input Buffers Enabled
Input Current
Input Current Drift
Crosstalk
INTERNAL REFERENCE
Output Voltage
Initial Accuracy3
Temperature Coefficient
0°C to 105°C
−40°C to +105°C
Reference Load Current, ILOAD
Power Supply Rejection
Load Regulation
Voltage Noise
Voltage Noise Density
Test Conditions/Comments
Excluding sinc3 filter ≥ 125 kSPS
See Table 6 and Table 7
See Table 6 and Table 7
Min
Typ
5
24
Analog input buffers enabled
Analog input buffers disabled
Internal short
Internal short
±3.5
±1
±40
±80
±35
±0.4
AVDD1, AVDD2, VIN = 1 V
VIN = 0.1 V
Max
Unit
250,000
SPS
Bits
±7.8
±3.5
ppm of FSR
ppm of FSR
µV
nV/°C
ppm of FSR
ppm/°C
±85
±0.75
95
20 Hz output data rate (post filter),
50 Hz ± 1 Hz and 60 Hz ± 1 Hz
50 Hz ± 1 Hz and 60 Hz ± 1 Hz
Internal clock, 20 SPS ODR (postfilter)
External clock, 20 SPS ODR (postfilter)
95
120
71
85
VREF = (REF+) − (REF−)
dB
dB
90
90
dB
dB
±VREF
V
AVSS − 0.05
AVSS
External clock
Internal clock (±2.5% clock)
AVDD1 − 0.2 V to AVSS + 0.2 V
AVDD1 to AVSS
1 kHz input
100 nF external capacitor to AVSS
REFOUT, with respect to AVSS
REFOUT, TA = 25°C
AVDD1 + 0.05
AVDD1
µA/V
nA/V/°C
nA/V/°C
±30
±75
±1
−120
nA
pA/°C
nA/°C
dB
2.5
−0.12
+0.12
−10
Rev. A | Page 3 of 60
V
V
±48
±0.75
±4
±2
±3
AVDD1, AVDD2, (line regulation)
∆VOUT/∆ILOAD
eN, 0.1 Hz to 10 Hz, 2.5 V reference
eN, 1 kHz, 2.5 V reference
dB
90
32
4.5
215
±5
±10
+10
V
% of V
ppm/°C
ppm/°C
mA
dB
ppm/mA
µV rms
nV/√Hz
AD7175-2
Parameter
Turn-On Settling Time
Short-Circuit Current, ISC
EXTERNAL REFERENCE INPUTS
Differential Input Range
Absolute Voltage Limits1
Input Buffers Disabled
Input Buffers Enabled
REFIN Input Current
Input Buffers Disabled
Input Current
Input Current Drift
Input Buffers Enabled
Input Current
Input Current Drift
Normal Mode Rejection1
Common-Mode Rejection
TEMPERATURE SENSOR
Accuracy
Sensitivity
BURNOUT CURRENTS
Source/Sink Current
GENERAL-PURPOSE I/O
(GPIO0, GPIO1)
Input Mode Leakage Current1
Floating State Output
Capacitance
Output High Voltage, VOH1
Output Low Voltage, VOL1
Input High Voltage, VIH1
Input Low Voltage, VIL1
CLOCK
Internal Clock
Frequency
Accuracy
Duty Cycle
Output Low Voltage, VOL
Output High Voltage, VOH
Crystal
Frequency
Startup Time
External Clock (CLKIO)
Duty Cycle1
Data Sheet
Test Conditions/Comments
100 nF REFOUT capacitor
Min
Typ
200
25
Max
Unit
µs
mA
VREF = (REF+) − (REF−)
1
2.5
AVDD1
V
AVDD1 + 0.05
AVDD1
V
V
AVSS − 0.05
AVSS
±72
±1.2
±6
µA/V
nA/V/°C
nA/V/°C
±800
1.25
nA
nA/°C
95
dB
After user calibration at 25°C
±2
477
°C
µV/K
Analog input buffers must be enabled
With respect to AVSS
±10
µA
External clock
Internal clock
See the Rejection parameter
−10
+10
5
ISOURCE = 200 µA
ISINK = 800 µA
AVSS + 4
AVSS + 0.4
AVSS + 3
AVSS + 0.7
16
−2.5%
+2.5%
50
0.4
0.8 × IOVDD
14
30
Rev. A | Page 4 of 60
16
10
16
50
16.384
16.384
70
µA
pF
V
V
V
V
MHz
%
%
V
V
MHz
µs
MHz
%
Data Sheet
Parameter
LOGIC INPUTS
Input High Voltage, VINH1
Input Low Voltage, VINL1
Hysteresis1
Leakage Currents
LOGIC OUTPUT (DOUT/RDY)
Output High Voltage, VOH1
Output Low Voltage, VOL1
Leakage Current
Output Capacitance
SYSTEM CALIBRATION1
Full-Scale (FS) Calibration Limit
Zero-Scale Calibration Limit
Input Span
POWER REQUIREMENTS
Power Supply Voltage
AVDD1 to AVSS
AVDD2 to AVSS
AVSS to DGND
IOVDD to DGND
IOVDD to AVSS
POWER SUPPLY CURRENTS4
Full Operating Mode
AVDD1 Current
AVDD2 Current
IOVDD Current
Standby Mode (LDO On)
Power-Down Mode
AD7175-2
Test Conditions/Comments
Min
2 V ≤ IOVDD < 2.3 V
2.3 V ≤ IOVDD ≤ 5.5 V
2 V ≤ IOVDD < 2.3 V
2.3 V ≤ IOVDD ≤ 5.5 V
IOVDD ≥ 2.7 V
IOVDD < 2.7 V
0.65 × IOVDD
0.7 × IOVDD
IOVDD ≥ 4.5 V, ISOURCE = 1 mA
2.7 V ≤ IOVDD < 4.5 V, ISOURCE = 500 µA
IOVDD < 2.7 V, ISOURCE = 200 µA
IOVDD ≥ 4.5 V, ISINK = 2 mA
2.7 V ≤ IOVDD < 4.5 V, ISINK = 1 mA
IOVDD < 2.7 V, ISINK = 400 µA
Floating state
Floating state
0.8 × IOVDD
0.8 × IOVDD
0.8 × IOVDD
Typ
0.08
0.04
−10
Max
Unit
0.35 × IOVDD
0.7
0.25
0.2
+10
V
V
V
V
V
V
µA
0.4
0.4
0.4
+10
−10
10
1.05 × FS
2.1 × FS
V
V
V
5.5
5.5
0
5.5
6.35
V
V
V
V
V
1.4
1.65
mA
1.75
2
mA
13
16
mA
−1.05 × FS
0.8 × FS
4.5
2
−2.75
2
For AVSS < DGND
All outputs unloaded, digital inputs
connected to IOVDD or DGND
Analog input and reference input
buffers disabled, external reference
Analog input and reference input
buffers disabled, internal reference
Analog input and reference input
buffers enabled, external reference
Each buffer: AIN+, AIN−, REF+, REF−
External reference
Internal reference
External clock
Internal clock
External crystal
Internal reference off, total current
consumption
Internal reference on, total current
consumption
Full power-down (including LDO and
internal reference)
Rev. A | Page 5 of 60
V
V
V
V
V
V
µA
pF
2.9
4.5
4.75
2.5
2.75
3
25
5
5.2
2.8
3.1
425
5
mA
mA
mA
mA
mA
mA
µA
µA
10
µA
AD7175-2
Data Sheet
Parameter
POWER DISSIPATION4
Full Operating Mode
Test Conditions/Comments
Min
All buffers disabled, external clock and
reference, AVDD2 = 2 V, IOVDD = 2 V
All buffers disabled, external clock and
reference, all supplies = 5 V
All buffers disabled, external clock and
reference, all supplies = 5.5 V
All buffers enabled, internal clock and
reference, AVDD2 = 2 V, IOVDD = 2 V
All buffers enabled, internal clock and
reference, all supplies = 5 V
All buffers enabled, internal clock and
reference, all supplies = 5.5 V
Internal reference off, all supplies = 5 V
Internal reference on, all supplies = 5 V
Full power-down, all supplies = 5 V
Standby Mode
Power-Down Mode
Typ
Max
Unit
21
mW
42
mW
52
mW
82
mW
105
mW
125
2.2
25
136
mW
50
µW
mW
µW
Specification is not production tested but is supported by characterization data at initial product release.
Following a system or internal zero-scale calibration, the offset error is in the order of the noise for the programmed output data rate selected. A system full-scale
calibration reduces the gain error to the order of the noise for the programmed output data rate.
3
This specification includes moisture sensitivity level (MSL) preconditioning effects.
4
This specification is with no load on the REFOUT and digital output pins.
1
2
TIMING CHARACTERISTICS
IOVDD = 2 V to 5.5 V, DGND = 0 V, Input Logic 0 = 0 V, Input Logic 1 = IOVDD, CLOAD = 20 pF, unless otherwise noted.
Table 2.
Parameter
SCLK
t3
t4
READ OPERATION
t1
t23
t5 5
t6
t7
WRITE OPERATION
t8
t9
t10
t11
Limit at TMIN, TMAX
Unit
Test Conditions/Comments1, 2
25
25
ns min
ns min
SCLK high pulse width
SCLK low pulse width
0
15
40
0
12.5
25
2.5
20
0
10
ns min
ns max
ns max
ns min
ns max
ns max
ns min
ns max
ns min
ns min
CS falling edge to DOUT/RDY active time
IOVDD = 4.75 V to 5.5 V
IOVDD = 2 V to 3.6 V
SCLK active edge to data valid delay4
IOVDD = 4.75 V to 5.5 V
IOVDD = 2 V to 3.6 V
Bus relinquish time after CS inactive edge
0
8
8
5
ns min
ns min
ns min
ns min
CS falling edge to SCLK active edge setup time4
Data valid to SCLK edge setup time
Data valid to SCLK edge hold time
CS rising edge to SCLK edge hold time
SCLK inactive edge to CS inactive edge
SCLK inactive edge to DOUT/RDY high/low
Sample tested during initial release to ensure compliance.
See Figure 2 and Figure 3.
3
This parameter is defined as the time required for the output to cross the VOL or VOH limits.
4
The SCLK active edge is the falling edge of SCLK.
5
DOUT/RDY returns high after a read of the data register. In single conversion mode and continuous conversion mode, the same data can be read again, if required,
while DOUT/RDY is high, although care must be taken to ensure that subsequent reads do not occur close to the next output update. If the continuous read feature is
enabled, the digital word can be read only once.
1
2
Rev. A | Page 6 of 60
Data Sheet
AD7175-2
TIMING DIAGRAMS
CS (I)
t6
t1
t5
MSB
DOUT/RDY (O)
LSB
t7
t2
t3
12468-003
SCLK (I)
t4
I = INPUT, O = OUTPUT
Figure 2. Read Cycle Timing Diagram
CS (I)
t11
t8
SCLK (I)
t9
t10
MSB
LSB
I = INPUT, O = OUTPUT
Figure 3. Write Cycle Timing Diagram
Rev. A | Page 7 of 60
12468-004
DIN (I)
AD7175-2
Data Sheet
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
THERMAL RESISTANCE
Table 3.
θJA is specified for a device soldered on a JEDEC test board for
surface-mount packages.
Parameter
AVDD1, AVDD2 to AVSS
AVDD1 to DGND
IOVDD to DGND
IOVDD to AVSS
AVSS to DGND
Analog Input Voltage to AVSS
Reference Input Voltage to AVSS
Digital Input Voltage to DGND
Digital Output Voltage to DGND
Analog Input/Digital Input Current
Operating Temperature Range
Storage Temperature Range
Maximum Junction Temperature
Lead Soldering, Reflow Temperature
ESD Rating (HBM)
Rating
−0.3 V to +6.5 V
−0.3 V to +6.5 V
−0.3 V to +6.5 V
−0.3 V to +7.5 V
−3.25 V to +0.3 V
−0.3 V to AVDD1 + 0.3 V
−0.3 V to AVDD1 + 0.3 V
−0.3 V to IOVDD + 0.3 V
−0.3 V to IOVDD + 0.3 V
10 mA
−40°C to +105°C
−65°C to +150°C
150°C
260°C
4 kV
Table 4. Thermal Resistance
Package Type
24-Lead TSSOP
JEDEC 1-Layer Board
JEDEC 2-Layer Board
ESD CAUTION
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
Rev. A | Page 8 of 60
θJA
Unit
149
81
°C/W
°C/W
Data Sheet
AD7175-2
AIN4 1
24
AIN3
REF– 2
23
AIN2
REF+ 3
22
AIN1
REFOUT 4
21
AIN0
REGCAPA 5
20
GPIO1
19
GPIO0
18
REGCAPD
AVDD2 8
17
DGND
XTAL1 9
16
IOVDD
XTAL2/CLKIO 10
15
SYNC/ERROR
DOUT/RDY 11
14
CS
DIN 12
13
SCLK
AVSS 6
AVDD1 7
AD7175-2
TOP VIEW
(Not to Scale)
12468-002
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 4. Pin Configuration
Table 5. Pin Function Descriptions
Pin No.
1
2
3
Mnemonic
AIN4
REF−
REF+
Type1
AI
AI
AI
4
5
6
7
8
9
10
REFOUT
REGCAPA
AVSS
AVDD1
AVDD2
XTAL1
XTAL2/CLKIO
AO
AO
P
P
P
AI
AI/DI
11
DOUT/RDY
DO
12
DIN
DI
13
SCLK
DI
14
CS
DI
Description
Analog Input 4. Selectable through crosspoint multiplexer.
Reference Input Negative Terminal. REF− can span from AVSS to AVDD1 − 1 V.
Reference Input Positive Terminal. An external reference can be applied between REF+ and REF−. REF+
can span from AVSS + 1 V to AVDD1.The device functions with a reference magnitude from 1 V to
AVDD1.
Buffered Output of Internal Reference. The output is 2.5 V with respect to AVSS.
Analog LDO Regulator Output. Decouple this pin to AVSS using a 1 µF and a 0.1 µF capacitor.
Negative Analog Supply. This supply ranges from −2.75 V to 0 V and is nominally set to 0 V.
Analog Supply Voltage 1. This voltage is 5 V ± 10% with respect to AVSS.
Analog Supply Voltage 2. This voltage ranges from 2 V to 5 V with respect to AVSS.
Input 1 for Crystal.
Input 2 for Crystal/Clock Input or Output. Based on the CLOCKSEL bits in the ADCMODE register. There
are four options available for selecting the MCLK source:
Internal oscillator: no output.
Internal oscillator: output to XTAL2/CLKIO. Operates at IOVDD logic level.
External clock: input to XTAL2/CLKIO. Input must be at IOVDD logic level.
External crystal: connected between XTAL1 and XTAL2/CLKIO.
Serial Data Output/Data Ready Output. DOUT/RDY is a dual purpose pin. It functions as a serial data
output pin to access the output shift register of the ADC. The output shift register can contain data
from any of the on-chip data or control registers. The data-word/control word information is placed on
the DOUT/RDY pin on the SCLK falling edge and is valid on the SCLK rising edge. When CS is high, the
DOUT/RDY output is three-stated. When CS is low, DOUT/RDY operates as a data ready pin, going low
to indicate the completion of a conversion. If the data is not read after the conversion, the pin goes
high before the next update occurs. The DOUT/RDY falling edge can be used as an interrupt to a
processor, indicating that valid data is available.
Serial Data Input to the Input Shift Register on the ADC. Data in this shift register is transferred to the
control registers in the ADC, with the register address (RA) bits of the communications register
identifying the appropriate register. Data is clocked in on the rising edge of SCLK.
Serial Clock Input. This serial clock input is for data transfers to and from the ADC. The SCLK has a
Schmitt triggered input, making the interface suitable for opto-isolated applications.
Chip Select Input. This is an active low logic input used to select the ADC. CS can be used to select the
ADC in systems with more than one device on the serial bus. CS can be hardwired low, allowing the ADC
to operate in 3-wire mode with SCLK, DIN, and DOUT used to interface with the device. When CS is
high, the DOUT/RDY output is three-stated.
Rev. A | Page 9 of 60
AD7175-2
Data Sheet
Pin No.
15
Mnemonic
SYNC/ERROR
Type1
DI/O
16
IOVDD
P
17
18
DGND
REGCAPD
P
AO
19
20
21
22
23
24
GPIO0
GPIO1
AIN0
AIN1
AIN2
AIN3
DI/O
DI/O
AI
AI
AI
AI
1
Description
Synchronization Input/Error Input/Output. This pin can be switched between a logic input and a logic
output in the GPIOCON register. When synchronization input (SYNC) is enabled, this pin allows
synchronization of the digital filters and analog modulators when using multiple AD7175-2 devices.
For more information, see the Synchronization section. When the synchronization input is disabled,
this pin can be used in one of three modes:
Active low error input mode: this mode sets the ADC_ERROR bit in the status register.
Active low, open-drain error output mode: the status register error bits are mapped to the ERROR
output. The SYNC/ERROR pins of multiple devices can be wired together to a common pull-up resistor
so that an error on any device can be observed.
General-purpose output mode: the status of the pin is controlled by the ERR_DAT bit in the GPIOCON
register. The pin is referenced between IOVDD and DGND, as opposed to the AVDD1 and AVSS levels
used by the GPIOx pins. The pin has an active pull-up in this case.
Digital I/O Supply Voltage. The IOVDD voltage ranges from 2 V to 5 V. IOVDD is independent of AVDD2.
For example, IOVDD can be operated at 3 V when AVDD2 equals 5 V, or vice versa. If AVSS is set to
−2.5 V, the voltage on IOVDD must not exceed 3.6 V.
Digital Ground.
Digital LDO Regulator Output. This pin is for decoupling purposes only. Decouple this pin to DGND
using a 1 μF and a 0.1 μF capacitor.
General-Purpose Input/Output 0. The pin is referenced between AVDD1 and AVSS levels.
General-Purpose Input/Output 1. The pin is referenced between AVDD1 and AVSS levels.
Analog Input 0. Selectable through the crosspoint multiplexer.
Analog Input 1. Selectable through the crosspoint multiplexer.
Analog Input 2. Selectable through the crosspoint multiplexer.
Analog Input 3. Selectable through the crosspoint multiplexer.
AI is analog input, AO is analog output, DI/O is bidirectional digital input/output, DO is digital output, DI is digital input, and P is power supply.
Rev. A | Page 10 of 60
Data Sheet
AD7175-2
TYPICAL PERFORMANCE CHARACTERISTICS
AVDD1 = 5 V, AVDD2 = 5 V, IOVDD = 3.3 V, TA = 25°C, unless otherwise noted.
8390000
1000
900
8389500
800
8389000
SAMPLE COUNT
ADC CODE
700
8388500
8388000
8387500
600
500
400
300
8387000
200
8386500
0
100
200
300
400 500 600 700
SAMPLE NUMBER
800
900
1000
0
12468-205
8386000
8388460 8388461 8388462 8388463 8388464 8388465 8388466
ADC CODE
Figure 5. Noise (Analog Input Buffers Disabled, VREF = 5 V,
Output Data Rate = 5 SPS)
12468-208
100
Figure 8. Histogram (Analog Input Buffers Disabled, VREF = 5 V,
Output Data Rate = 5 SPS)
120
8388480
8388475
100
SAMPLE COUNT
ADC CODE
8388470
8388465
8388460
80
60
40
8388455
100
200
300
400 500 600 700
SAMPLE NUMBER
800
900
1000
0
ADC CODE
Figure 6. Noise (Analog Input Buffers Disabled, VREF = 5 V,
Output Data Rate = 10 kSPS)
12468-209
0
12468-206
8388445
8388450
8388451
8388452
8388453
8388454
8388455
8388456
8388457
8388458
8388459
8388460
8388461
8388462
8388463
8388464
8388465
8388466
8388467
8388468
8388469
8388470
8388471
8388472
8388473
8388474
8388475
8388476
8388477
20
8388450
Figure 9. Histogram (Analog Input Buffers Disabled, VREF = 5 V,
Output Data Rate = 10 kSPS)
8388520
45
40
8388500
35
SAMPLE COUNT
8388460
8388440
30
25
20
15
10
8388420
100
200
300
400 500 600 700
SAMPLE NUMBER
800
900
1000
0
ADC CODE
Figure 7. Noise (Analog Input Buffers Disabled, VREF = 5 V,
Output Data Rate = 250 kSPS)
Figure 10. Histogram (Analog Input Buffers Disabled, VREF = 5 V,
Output Data Rate = 250 kSPS)
Rev. A | Page 11 of 60
12468-210
0
8388420
8388422
8388424
8388426
8388428
8388430
8388432
8388434
8388436
8388438
8388440
8388442
8388444
8388446
8388448
8388450
8388452
8388454
8388456
8388458
8388460
8388462
8388464
8388466
8388468
8388470
8388472
8388474
8388476
8388478
8388480
8388482
8388484
8388486
8388488
8388490
8388492
8388494
8388496
8388498
8388500
8388502
8388504
5
8388400
12468-207
ADC CODE
8388480
Data Sheet
1000
8389500
900
8389000
800
8388500
700
8388000
8387500
8387000
600
500
400
8386500
300
8386000
200
8385500
100
8385000
0
100
200
300
400 500 600 700
SAMPLE NUMBER
800
900
1000
0
8388490 8388491 8388492 8388493 8388494 8388495 8388496
ADC CODE
12468-214
SAMPLE COUNT
8390000
12468-211
ADC CODE
AD7175-2
Figure 14. Histogram (Analog Input Buffers Enabled, VREF = 5 V,
Output Data Rate = 5 SPS)
Figure 11. Noise (Analog Input Buffers Enabled, VREF = 5 V,
Output Data Rate = 5 SPS)
100
8388520
90
8388515
80
8388510
SAMPLE COUNT
ADC CODE
70
8388505
8388500
8388495
60
50
40
30
8388490
20
8388485
200
300
400 500 600 700
SAMPLE NUMBER
800
900
1000
0
ADC CODE
Figure 15. Histogram (Analog Input Buffers Enabled, VREF = 5 V,
Output Data Rate = 10 kSPS)
35
8388560
30
8388540
25
8388520
8388500
20
15
8388480
10
8388460
5
8388440
100
200
300
400 500 600 700
SAMPLE NUMBER
800
900
1000
0
8388460
8388462
8388464
8388466
8388468
8388470
8388472
8388474
8388476
8388478
8388480
8388482
8388484
8388486
8388488
8388490
8388492
8388494
8388496
8388498
8388500
8388502
8388504
8388506
8388508
8388510
8388512
8388514
8388516
8388518
8388520
8388522
8388524
8388526
8388528
8388530
8388532
SAMPLE COUNT
8388580
12468-213
ADC CODE
Figure 12. Noise (Analog Input Buffers Enabled, VREF = 5 V,
Output Data Rate = 10 kSPS)
0
12468-215
100
ADC CODE
Figure 13. Noise (Analog Input Buffers Enabled, VREF = 5 V,
Output Data Rate = 250 kSPS)
Figure 16. Histogram (Analog Input Buffers Enabled, VREF = 5 V,
Output Data Rate = 250 kSPS)
Rev. A | Page 12 of 60
12468-216
0
12468-212
8388480
8388480
8388481
8388482
8388483
8388484
8388485
8388486
8388487
8388488
8388489
8388490
8388491
8388492
8388493
8388494
8388495
8388496
8388497
8388498
8388499
8388500
8388501
8388502
8388503
8388504
8388505
8388506
8388507
8388508
8388509
8388510
8388511
8388512
8388513
8388514
10
Data Sheet
0.000016
AD7175-2
0
BUFFER ON
BUFFER OFF
0.000014
–20
0.000012
–40
CMRR (dB)
NOISE (V)
0.000010
0.000008
0.000006
–60
–80
0.000004
–100
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
INPUT COMMON-MODE VOLTAGE (V)
4.5
5.0
–120
12468-217
0
1
100
1k
10k
VIN FREQUENCY (Hz)
100k
1M
Figure 20. Common-Mode Rejection Ratio (CMRR) vs. VIN Frequency
(VIN = 0.1 V, Output Data Rate = 250 kSPS)
Figure 17. Noise vs. Input Common-Mode Voltage, Analog Input Buffers On and
Off
–80
ANALOG INPUT BUFFERS OFF
ANALOG INPUT BUFFERS ON
18
–90
–100
14
–110
12
–120
CMRR (dB)
16
10
8
–130
–140
6
–150
4
–160
2
–170
0
2
4
6
8
10
FREQUENCY (MHz)
12
14
16
–180
10
12468-218
0
Figure 18. Noise vs. External Master Clock Frequency,
Analog Input Buffers On and Off
16800000
30
40
50
VIN FREQUENCY (Hz)
60
70
Figure 21. Common-Mode Rejection Ratio (CMRR) vs. VIN Frequency
(VIN = 0.1 V, 10 Hz to 70 Hz, Output Data Rate = 20 SPS Enhanced Filter)
CONTINUOUS CONVERSION—REFERENCE DISABLED
STANDBY—REFERENCE DISABLED
STANDBY—REFERENCE ENABLED
16780000
20
12468-227
20
NOISE (µV rms)
10
12468-226
0.000002
–60
AVDD1—EXTERNAL 2.5V REFERENCE
AVDD1—INTERNAL 2.5V REFERENCE
–70
–80
PSRR (dB)
16740000
16720000
–90
–100
16700000
–110
16680000
1
10
100
SAMPLE NUMBER
1k
10k
Figure 19. Internal Reference Settling Time
–130
1
10
100
1k
10k
100k
VIN FREQUENCY (Hz)
1M
10M
100M
Figure 22. Power Supply Rejection Ratio (PSRR) vs. VIN Frequency
Rev. A | Page 13 of 60
12468-228
–120
16660000
12468-225
OUTPUT CODE
16760000
AD7175-2
20
30
INTERNAL 2.5V REF,
ANALOG INPUT BUFFERS OFF
INTERNAL 2.5V REF,
ANALOG INPUT BUFFERS ON
EXTERNAL 2.5V REF,
ANALOG INPUT BUFFERS OFF
EXTERNAL 2.5V REF,
ANALOG INPUT BUFFERS ON
EXTERNAL 5V REF,
ANALOG INPUT BUFFERS OFF
EXTERNAL 5V REF,
ANALOG INPUT BUFFERS ON
10
5
25
SAMPLE COUNT
15
INL (ppm of FS)
Data Sheet
0
–5
20
15
10
–10
5
–4
–3
–2
–1
0
1
2
4
3
5
VIN (V)
Figure 23. Integral Nonlinearity (INL) vs. VIN
(Differential Input)
0.5
30
30
25
25
20
20
15
10
1.5
2.0
2.5
3.0
3.5
INL ERROR (ppm)
4.0
4.5
5.0
15
10
2.50 2.75 3.00 3.25 3.50 3.75 4.00 4.25 4.50 4.75 5.00
INL ERROR (ppm)
0
12468-230
0
Figure 24. Integral Nonlinearity (INL) Distribution Histogram (Differential
Input, Analog Input Buffers Enabled, VREF = 2.5 V External, 100 Units)
0.2
0.4
0.6
0.8
1.0
1.2
INL ERROR (ppm)
1.4
1.6
12468-233
5
5
Figure 27. Integral Nonlinearity (INL) Distribution Histogram (Analog Input
Buffers Disabled, Differential Input, VREF = 5 V External, 100 Units)
30
5.0
BUFFER DISABLED
BUFFER ENABLED
4.5
25
4.0
3.5
20
INL (ppm of FSR)
SAMPLE COUNT
1.0
Figure 26. Integral Nonlinearity (INL) Distribution Histogram (Analog Input
Buffers Enabled, Differential Input, VREF = 5 V External, 100 Units)
SAMPLE COUNT
SAMPLE COUNT
0
12468-229
–20
–5
12468-232
–15
15
10
3.0
2.5
2.0
1.5
1.0
5
0.4
0.6
0.8
1.0
1.2
1.4
INL ERROR (ppm)
1.6
1.8
2.0
Figure 25. Integral Nonlinearity (INL) Distribution Histogram (Differential
Input, Analog Input Buffers Disabled, VREF = 2.5 V External, 100 Units)
Rev. A | Page 14 of 60
0
–40
–20
0
20
40
60
TEMPERATURE (°C)
80
Figure 28. Integral Nonlinearity (INL) vs. Temperature
(Differential Input, VREF = 2.5 V External)
100
12468-234
0.2
12468-231
0.5
0
AD7175-2
50
45
45
40
40
35
35
SAMPLE COUNT
50
30
25
20
25
20
15
10
10
5
5
15.99
16.00 16.01 16.02 16.03
FREQUENCY (MHz)
16.04
16.05
0
–40 –30 –20 –10 0
Figure 29. Internal Oscillator Frequency/Accuracy Distribution Histogram
(100 Units)
Figure 32. Offset Error Distribution Histogram (Internal Short)
(248 Units)
16400000
35
16300000
30
16200000
SAMPLE COUNT
25
16100000
16000000
15900000
20
15
10
15800000
0
20
40
60
TEMPERATURE (°C)
80
100
0
12468-236
–20
12468-239
5
15700000
15600000
–40
10 20 30 40 50 60 70 80 90
OFFSET ERROR (µV)
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
10
20
30
40
50
60
70
80
90
100
110
120
15.98
12468-238
0
FREQUENCY (Hz)
30
15
12468-235
SAMPLE COUNT
Data Sheet
OFFSET DRIFT ERROR (nV/°C)
Figure 30. Internal Oscillator Frequency vs. Temperature
Figure 33. Offset Error Drift Distribution Histogram (Internal Short)
(248 Units)
0.0010
40
35
SAMPLE COUNT
30
0
–0.0005
25
20
15
10
–0.0010
–40
–20
0
20
40
60
TEMPERATURE (°C)
80
Figure 31. Absolute Reference Error vs. Temperature
100
0
–4
–3
–2
–1
0
1
2
GAIN ERROR (ppm/FSR)
3
4
12468-240
5
12468-237
ERROR (V)
0.0005
Figure 34. Gain Error Distribution Histogram (Analog Input Buffers Enabled)
(100 Units)
Rev. A | Page 15 of 60
AD7175-2
Data Sheet
0.025
30
0.020
20
CURRENT (A)
15
0.015
0.010
10
0.005
5
34
35
36
37
38
39
40
GAIN ERROR (ppm/FSR)
41
42
43
0
–40
12468-241
0
Figure 35. Gain Error Distribution Histogram
(Analog Input Buffers Disabled, 100 Units)
BUFFERS DISABLED
BUFFERS ENABLED
–20
0
20
40
60
TEMPERATURE (°C)
80
100
12468-244
SAMPLE COUNT
25
Figure 38. Current Consumption vs. Temperature
(Continuous Conversion Mode)
1.6
25
1.4
20
CURRENT (µA)
SAMPLE COUNT
1.2
15
10
1.0
0.8
0.6
0.4
5
0
–40
GAIN ERROR DRIFT (ppm/FSR)
12468-242
0.30
0.28
0.26
0.24
0.22
0.20
0.18
0.16
0.14
0.12
0.10
0.08
0.06
0.04
0
0.02
–0.02
0
Figure 36. Gain Error Drift Distribution Histogram
(Analog Input Buffers Enabled, 100 Units)
0
20
40
60
TEMPERATURE (°C)
80
100
Figure 39. Current Consumption vs. Temperature (Power-Down Mode)
40
18
35
16
14
SAMPLE COUNT
30
25
20
15
10
12
10
8
6
4
5
0
0.10
0.15
0.20 0.25 0.30 0.35 0.40 0.45
GAIN ERROR DRIFT (ppm/FSR)
0.50
0.55
Figure 37. Gain Error Drift Distribution Histogram
(Analog Input Buffers Disabled, 100 Units)
0
–1.2 –1.0 –0.8 –0.6 –0.4 –0.2 0
0.2 0.4
TEMPERATURE DELTA (°C)
0.6
0.8
1.0
Figure 40. Temperature Sensor Distribution Histogram
(Uncalibrated, 100 Units)
Rev. A | Page 16 of 60
12468-246
2
12468-243
SAMPLE COUNT
–20
12468-245
0.2
Data Sheet
AD7175-2
100
35
80
30
60
INPUT CURRENT (nA)
SAMPLE COUNT
25
20
15
10
AIN+ = AVDD1 – 0.2V
AIN– = AVSS + 0.2V
AIN+ = AVDD1
AIN– = AVSS
40
20
0
–20
–40
–60
5
9.60 9.65 9.70 9.75 9.80 9.85 9.90 9.95 10.00 10.05 10.10
CURRENT (µA)
Figure 41. Burnout Current Distribution Histogram
(100 Units)
100
40
20
0
–20
–40
–60
–80
–100
–5
–4
–3
–2
–1
0
1
2
INPUT VOLTAGE (V)
3
4
5
12468-248
INPUT CURRENT (nA)
60
–20
0
20
40
60
TEMPERATURE (°C)
80
Figure 43. Analog Input Current vs. Temperature
–40°C, AIN+
–40°C, AIN–
+25°C, AIN+
+25°C, AIN–
+105°C, AIN+
+105°C, AIN–
80
–100
–40
Figure 42. Analog Input Current vs. Input Voltage
(VCM = 2.5 V)
Rev. A | Page 17 of 60
100
12468-249
0
12468-247
–80
AD7175-2
Data Sheet
NOISE PERFORMANCE AND RESOLUTION
Table 6 and Table 7 show the rms noise, peak-to-peak noise,
effective resolution and the noise free (peak-to-peak) resolution
of the AD7175-2 for various output data rates and filters. The
numbers given are for the bipolar input range with an external
5 V reference. These numbers are typical and are generated with
a differential input voltage of 0 V when the ADC is
continuously converting on a single channel. It is important to
note that the peak-to-peak resolution is calculated based on the
peak-to-peak noise. The peak-to-peak resolution represents the
resolution for which there is no code flicker.
Table 6. RMS Noise and Peak-to-Peak Resolution vs. Output Data Rate using Sinc5 + Sinc1 Filter (Default)1
Output Data Rate (SPS)
Input Buffers Disabled
250,000
62,500
10,000
1000
59.92
49.96
16.66
5
Input Buffers Enabled
250,000
62,500
10,000
1000
59.98
49.96
16.66
5
1
RMS Noise (µV rms)
Effective Resolution (Bits)
Peak-to-Peak Noise (µV p-p)
Peak-to-Peak Resolution (Bits)
8.7
5.5
2.5
0.77
0.19
0.18
0.1
0.07
20.1
20.8
21.9
23.6
24
24
24
24
65
43
18.3
5.2
1.1
0.95
0.45
0.34
17.2
17.8
19.1
20.9
23.1
23.3
24
24
9.8
6.4
3
0.92
0.23
0.2
0.13
0.07
20
20.6
21.7
23.4
24
24
24
24
85
55
23
5.7
1.2
1
0.66
0.32
16.8
17.5
18.7
20.7
23.0
23.3
23.9
24
Selected rates only, 1000 samples.
Table 7. RMS Noise and Peak-to-Peak Resolution vs. Output Data Rate using Sinc3 Filter1
Output Data Rate (SPS)
Input Buffers Disabled
250,000
62,500
10,000
1000
60
50
16.66
5
Input Buffers Enabled
250,000
62,500
10,000
1000
60
50
16.66
5
1
RMS Noise (µV rms)
Effective Resolution (Bits)
Peak-to-Peak Noise (µV p-p)
Peak-to-Peak Resolution (Bits)
210
5.2
1.8
0.56
0.13
0.13
0.07
0.05
15.5
20.9
22.4
24
24
24
24
24
1600
40
14
3.9
0.8
0.7
0.37
0.21
12.6
17.9
19.4
21.3
23.6
23.8
24
24
210
5.8
2.1
0.71
0.17
0.15
0.12
0.08
15.5
20.7
22.2
23.7
24
24
24
24
1600
48
16
4.5
1.1
0.83
0.6
0.35
12.6
17.7
19.3
21.1
23.1
23.5
24
24
Selected rates only, 1000 samples.
Rev. A | Page 18 of 60
Data Sheet
AD7175-2
GETTING STARTED
The AD7175-2 includes a precision 2.5 V low drift (±2 ppm/°C)
band gap internal reference. This reference can used for the
ADC conversions, reducing the external component count.
Alternatively, the reference can be output to the REFOUT pin to
be used as a low noise biasing voltage for external circuitry. An
example of this is using the REFOUT signal to set the input
common mode for an external amplifier.
The AD7175-2 offers the user a fast settling, high resolution,
multiplexed ADC with high levels of configurability.
•
•
•
Two fully differential or four single-ended analog inputs.
Crosspoint multiplexer selects any analog input combination as the input signals to be converted, routing them to
the modulator positive or negative input.
True rail-to-rail buffered analog and reference inputs.
Fully differential input or single-ended input relative to any
analog input.
Per channel configurability—up to four different setups
can be defined. A separate setup can be mapped to each of
the channels. Each setup allows the user to configure
whether the buffers are enabled or disabled, gain and offset
correction, filter type, output data rate, and reference
source selection (internal/external).
The AD7175-2 includes two separate linear regulator blocks for
both the analog and digital circuitry. The analog LDO regulates
the AVDD2 supply to 1.8 V, supplying the ADC core. The user
can tie the AVDD1 and AVDD2 supplies together for easiest
connection. If there is already a clean analog supply rail in the
system in the range of 2 V (minimum) to 5.5 V (maximum), the
user can also choose to connect this to the AVDD2 input,
allowing lower power dissipation.
GENERAL-PURPOSE I/O 0 AND
GENERAL-PURPOSE I/O 1
OUTPUT HIGH = AVDDx
GPIO1
OUTPUT LOW = AVSS
GPIO0
16MHz
19
20
GPIO0
GPIO1
OPTIONAL EXTERNAL
CRYSTAL CIRCUITRY
CAPACITORS
XTAL1 9
21
CX2
CX1
AIN0
XTAL2/CLKI0 10
DOUT/RDY 11
22
DOUT/RDY
AIN1
DIN
DIN 12
23
SCLK
SCLK 13
AIN2
CS
CS 14
24
AIN3
1
AIN4
CLKIN
OPTIONAL
EXTERNAL
CLOCK
INPUT
SYNC/ERROR 15
SYNC/ERROR
AD7175-2
IOVDD
IOVDD 16
0.1µF
DGND 17
VIN
1
2
4.7µF
VIN
3
REGCAPD 18
NC 7
0.1µF
1µF
0.1µF
ADR445BRZ
4
GND
5
VOUT 6
8
AVDD1
AVDD1 7
0.1µF
4.7µF
3
REF+
2
REF–
4
REFOUT
0.1µF
AVDD2
0.1µF
AVDD2 8
2.5V REFERENCE
OUTPUT
0.1µF
REGCAPA 5
0.1µF
0.1µF
AVSS
1µF
6
0.1µF
Figure 44. Typical Connection Diagram
Rev. A | Page 19 of 60
12468-051
•
•
AD7175-2
Data Sheet
The linear regulator for the digital IOVDD supply performs a
similar function, regulating the input voltage applied at the
IOVDD pin to 1.8 V for the internal digital filtering. The serial
interface signals always operate from the IOVDD supply seen at
the pin. This means that if 3.3 V is applied to the IOVDD pin,
the interface logic inputs and outputs operate at this level.
The AD7175-2 can be used across a wide variety of applications,
providing high resolution and accuracy. A sample of these
scenarios is as follows:
•
•
•
Fast scanning of analog input channels using the internal
multiplexer
Fast scanning of analog input channels using an external
multiplexer with automatic control from the GPIOs.
High resolution at lower speeds in either channel scanning
or ADC per channel applications
Single ADC per channel: the fast low latency output allows
further application specific filtering in an external microcontroller, DSP, or FPGA
The communications register controls access to the full register
map of the ADC. This register is an 8-bit write only register. On
power-up or after a reset, the digital interface defaults to a state
where it is expecting a write to the communications register;
therefore, all communication begins by writing to the
communications register.
The data written to the communications register determines
which register is being accessed and if the next operation is a
read or write. The register address bits (RA[5:0]) determine the
specific register to which the read or write operation applies.
When the read or write operation to the selected register is
complete, the interface returns to its default state, where it
expects a write operation to the communications register.
Figure 46 and Figure 47 illustrate writing to and reading from a
register by first writing the 8-bit command to the communications
register, followed by the data for that register.
POWER SUPPLIES
8 BITS, 16 BITS,
OR 24 BITS OF DATA
CMD
DATA
CS
The AD7175-2 has three independent power supply pins:
AVDD1, AVDD2, and IOVDD.
AVDD2 powers the internal 1.8 V analog LDO regulator. This
regulator powers the ADC core. AVDD2 is referenced to AVSS,
and AVDD2 − AVSS can range from 5.5 V (maximum) to 2 V
(minimum).
DIN
SCLK
Figure 46. Writing to a Register
(8-Bit Command with Register Address Followed by Data of 8, 16, or 24 Bits;
Data Length on DIN Is Dependent on the Register Selected)
8-BIT COMMAND
IOVDD powers the internal 1.8 V digital LDO regulator. This
regulator powers the digital logic of the ADC. IOVDD sets the
voltage levels for the SPI interface of the ADC. IOVDD is referenced to DGND, and IOVDD − DGND can vary from 5.5 V
(maximum) to 2 V (minimum).
DIGITAL COMMUNICATION
12468-053
AVDD1 powers the crosspoint multiplexer and integrated analog
and reference input buffers. AVDD1 is referenced to AVSS, and
AVDD1 − AVSS = 5 V only. This can be a single 5 V supply or a
±2.5 V split supply. The split supply operation allows true
bipolar inputs. When using split supplies, consider the absolute
maximum ratings (see the Absolute Maximum Ratings section).
12468-052
SAMPLE EDGE
8 BITS, 16 BITS,
24 BITS, OR
32 BITS OUTPUT
CS
DIN
DOUT/RDY
The AD7175-2 has a 3- or 4-wire SPI interface that is compatible
with QSPI™, MICROWIRE®, and DSPs. The interface operates
in SPI Mode 3 and can be operated with CS tied low. In SPI
Mode 3, the SCLK idles high, the falling edge of SCLK is the
drive edge, and the rising edge of SCLK is the sample edge. This
means that data is clocked out on the falling/drive edge and data
is clocked in on the rising/sample edge.
DRIVE EDGE
8-BIT COMMAND
SCLK
CMD
DATA
12468-054
•
Accessing the ADC Register Map
Figure 47. Reading from a Register
(8-Bit Command with Register Address Followed by Data of 8, 16, or 24 Bits;
Data Length on DOUT Is Dependent on the Register Selected)
Reading the ID register is the recommended method for verifying
correct communication with the device. The ID register is a
read only register and contains the value 0x0CDX for the
AD7175-2. The communications register and the ID register
details are described in Table 8 and Table 9.
Figure 45. SPI Mode 3 SCLK Edges
Rev. A | Page 20 of 60
Data Sheet
AD7175-2
AD7175-2 RESET
Figure 48 shows an overview of the suggested flow for changing
the ADC configuration, divided into the following three blocks:
In situations where interface synchronization is lost, a write
operation of at least 64 serial clock cycles with DIN high returns the
ADC to its default state by resetting the entire device, including
the register contents. Alternatively, if CS is being used with the
digital interface, returning CS high sets the digital interface to its
default state and halts any serial interface operation.
•
•
•
Channel Configuration
CONFIGURATION OVERVIEW
The AD7175-2 has four independent channels and four independent setups. The user can select any of the analog input pairs on
any channel, as well as any of the four setups for any channel,
giving the user full flexibility in the channel configuration. This
also allows per channel configuration when using differential
inputs and single-ended inputs because each channel can have
its own dedicated setup.
After power-on or reset, the AD7175-2 default configuration is
as follows:
•
•
•
•
Channel configuration. CH0 is enabled, AIN0 is selected
as the positive input, and AIN1 is selected as the negative
input. Setup 0 is selected.
Setup configuration. The internal reference and the analog
input buffers are enabled. The reference input buffers are
disabled.
Filter configuration. The sinc5 + sinc 1 filter is selected and
the maximum output data rate of 250 kSPS is selected.
ADC mode. Continuous conversion mode and the internal
oscillator are enabled.
Interface mode. CRC and data + status output are disabled.
Channel Registers
The channel registers are used to select which of the five analog
input pins (AIN0 to AIN4) are used as either the positive analog
input (AIN+) or the negative analog input (AIN−) for that
channel. This register also contains a channel enable/disable bit
and the setup selection bits, which are used to pick which of the
four available setups to use for this channel.
When the AD7175-2 is operating with more than one channel
enabled, the channel sequencer cycles through the enabled
channels in sequential order, from Channel 0 to Channel 3. If a
channel is disabled, it is skipped by the sequencer. Details of the
channel register for Channel 0 are shown in Table 10.
Note that only a few of the register setting options are shown;
this list is just an example. For full register information, see the
Register Details section.
A
CHANNEL CONFIGURATION
SELECT POSITIVE AND NEGATIVE INPUT FOR EACH ADC CHANNEL
SELECT ONE OF 4 SETUPS FOR ADC CHANNEL
B
SETUP CONFIGURATION
4 POSSIBLE ADC SETUPS
SELECT FILTER ORDER, OUTPUT DATA RATE, AND MORE
C
ADC MODE AND INTERFACE MODE CONFIGURATION
SELECT ADC OPERATING MODE, CLOCK SOURCE,
ENABLE CRC, DATA + STATUS, AND MORE
12468-044
•
Channel configuration (see Box A in Figure 48)
Setup configuration (see Box B in Figure 48)
ADC mode and interface mode configuration (see Box C
in Figure 48)
Figure 48. Suggested ADC Configuration Flow
Table 8. Communications Register
Reg.
0x00
Name
COMMS
Bits
[7:0]
Bit 7
WEN
Bit 6
R/W
Bit 5
Bits
[15:8]
[7:0]
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
0x00
RW
W
Bit 2
Bit 1
Bit 0
Reset
0x0CDX
RW
R
RA
Table 9. ID Register
Reg.
0x07
Name
ID
Bit 4
Bit 3
ID[15:8]
ID[7:0]
Table 10. Channel 0 Register
Reg.
0x10
Name
CH0
Bits
[15:8]
[7:0]
Bit 7
CH_EN0
Bit 6
Bit 5
Bit 4
Reserved
SETUP_SEL[2:0]
AINPOS0[2:0]
Bit 3
Rev. A | Page 21 of 60
Bit 2
Reserved
AINNEG0
Bit 1
Bit 0
AINPOS0[4:3]
Reset
0x8001
RW
RW
AD7175-2
Data Sheet
ADC Setups
Setup Configuration Registers
The AD7175-2 has four independent setups. Each setup consists
of the following four registers:
The setup configuration registers allow the user to select the output
coding of the ADC by selecting between bipolar and unipolar. In
bipolar mode, the ADC accepts negative differential input voltages,
and the output coding is offset binary. In unipolar mode, the ADC
accepts only positive differential voltages, and the coding is straight
binary. In either case, the input voltage must be within the AVDD1/
AVSS supply voltages. The user can select the reference source
using this register. Three options are available: an internal 2.5 V
reference, an external reference connected between the REF+
and REF− pins, or AVDD1 − AVSS. The analog input and
reference input buffers can also be enabled or disabled using
this register.
•
•
•
•
Setup configuration register
Filter configuration register
Offset register
Gain register
For example, Setup 0 consists of Setup Configuration Register 0,
Filter Configuration Register 0, Gain Register 0, and Offset
Register 0. Figure 49 shows the grouping of these registers The
setup is selectable from the channel registers (see the Channel
Configuration section), which allows each channel to be
assigned to one of four separate setups. Table 11 through Table 14
show the four registers that are associated with Setup 0. This
structure is repeated for Setup 1 to Setup 3.
Filter Configuration Registers
The filter configuration register selects which digital filter is
used at the output of the ADC modulator. The order of the filter
and the output data rate is selected by setting the bits in this
register. For more information, see the Digital Filters section.
FILTER CONFIG
REGISTERS
SETUP CONFIG
REGISTERS
GAIN REGISTERS*
OFFSET REGISTERS
SETUPCON0 0x20
FILTCON0 0x28
GAIN0
0x38
OFFSET0 0x30
SETUPCON1 0x21
FILTCON1 0x29
GAIN1
0x39
OFFSET1 0x31
SETUPCON2 0x22
FILTCON2 0x2A
GAIN2
0x3A
OFFSET2 0x32
SETUPCON3 0x23
FILTCON3 0x2B
GAIN3
0x3B
OFFSET3 0x33
DATA OUTPUT CODING
REFERENCE SOURCE
INPUT BUFFERS
SELECT DIGITAL
FILTER TYPE
AND OUTPUT DATA RATE
GAIN CORRECTION
OFFSET CORRECTION
OPTIONALLY
OPTIONALLY PROGRAMMED
PROGRAMMED
PER SETUP AS REQUIRED
PER SETUP AS REQUIRED
(*FACTORY CALIBRATED)
SINC5 + SINC1
SINC3
SINC3 MAP
ENHANCED 50Hz AND 60Hz
12468-045
SELECT PERIPHERAL
FUNCTIONS FOR
ADC CHANNEL
Figure 49. ADC Setup Register Grouping
Table 11. Setup Configuration 0 Register
Reg.
0x20
Name
Bits
Bit 7
Bit 6
SETUPCON0 [15:8]
Reserved
[7:0]
BURNOUT_EN0 Reserved
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
BI_UNIPOLAR0 REFBUF0+ REFBUF0− AINBUF0+ AINBUF0− 0x1320
REF_SEL0
Reserved
RW
RW
Table 12. Filter Configuration 0 Register
Reg.
0x28
Name
FILTCON0
Bits
Bit 7
[15:8] SINC3_MAP0
[7:0] Reserved
Bit 6
Bit 5
Bit 4
Reserved
ORDER0
Bit 3
Bit 2
ENHFILTEN0
ODR0
Bit 1
Bit 0
ENHFILT0
Reset
0x0500
RW
RW
Table 13. Gain Configuration 0 Register
Reg.
0x38
Name
GAIN0
Bits
[23:0]
Bit[23:0]
GAIN0[23:0]
Reset
RW
0x5XXXX0 RW
Bit[23:0]
OFFSET0[23:0]
Reset
RW
0x800000 RW
Table 14. Offset Configuration 0 Register
Reg.
0x30
Name
OFFSET0
Bits
[23:0]
Rev. A | Page 22 of 60
Data Sheet
AD7175-2
Gain Registers
ADC Mode and Interface Mode Configuration
The gain register is a 24-bit register that holds the gain
calibration coefficient for the ADC. The gain registers are
read/write registers. These registers are configured at power-on
with factory calibrated coefficients. Therefore, every device has
different default coefficients. The default value is automatically
overwritten if a system full-scale calibration is initiated by the
user or if the gain register is written to by the user. For more
information on calibration, see the Operating Modes section.
The ADC mode register and the interface mode register configure
the core peripherals for use by the AD7175-2 and the mode for
the digital interface.
ADC Mode Register
The ADC mode register is used primarily to set the conversion
mode of the ADC to either continuous or single conversion.
The user can also select the standby and power-down modes,
as well as any of the calibration modes. In addition, this register
contains the clock source select bits and the internal reference
enable bits. The reference select bits are contained in the setup
configuration registers (see the ADC Setups section for more
information).
Offset Registers
The offset register holds the offset calibration coefficient for the
ADC. The power-on reset value of the offset register is 0x800000.
The offset register is a 24-bit read/write register. The power-on
reset value is automatically overwritten if an internal or system
zero-scale calibration is initiated by the user or if the offset register
is written to by the user.
Interface Mode Register
The interface mode register configures the digital interface
operation. This register allows the user to control data-word
length, CRC enable, data plus status read, and continuous read
mode. The details of both registers are shown in Table 15 and
Table 16. For more information, see the Digital Interface section.
Table 15. ADC Mode Register
Reg.
0x01
Name
ADCMODE
Bits
[15:8]
[7:0]
Bit 7
REF_EN
Reserved
Bit 6
HIDE_DELAY
Bit 5
SING_CYC
Mode
Bit 4
Bit 3
Reserved
Bit 2
CLOCKSEL
Bit 1
Bit 0
Delay
Reserved
Reset
0x8000
RW
RW
Reset
0x0000
RW
RW
Table 16. Interface Mode Register
Reg.
0x02
Name
IFMODE
Bits
[15:8]
[7:0]
Bit 7
CONTREAD
Bit 6
Reserved
DATA_STAT
Bit 5
REG_CHECK
Bit 4
ALT_SYNC
Reserved
Bit 3
Bit 2
Bit 1
IOSTRENGTH
Reserved
CRC_EN
Reserved
Rev. A | Page 23 of 60
Bit 0
DOUT_RESET
WL16
AD7175-2
Data Sheet
Understanding Configuration Flexibility
The most straightforward implementation of the AD7175-2 is
to use two differential inputs with adjacent analog inputs and
run both of them with the same setup, gain correction, and
offset correction register. In this case, the user selects the
following differential inputs: AIN0/AIN1 and AIN2/AIN3. In
Figure 50, the registers shown in black font must be
programmed for such a configuration. The registers that are
shown in gray font are redundant in this configuration.
CHANNEL
REGISTERS
CH0
AIN1
CH1
AIN2
CH2
AIN3
CH3
AIN4
An alternative way to implement these two fully differential
inputs is by taking advantage of the four available setups.
Motivation for doing this includes having a different speed/noise
requirement on each of the differential inputs, or there may be a
specific offset or gain correction for each channel. Figure 51
shows how each of the differential inputs can use a separate
setup, allowing full flexibility in the configuration of each channel.
FILTER CONFIG
REGISTERS
GAIN REGISTERS*
OFFSET REGISTERS
0x10
SETUPCON0 0x20
FILTCON0 0x28
GAIN0
0x38
OFFSET0 0x30
0x11
SETUPCON1 0x21
FILTCON1 0x29
GAIN1
0x39
OFFSET1 0x31
0x12
SETUPCON2 0x22
FILTCON2 0x2A
GAIN2
0x3A
OFFSET2 0x32
0x13
SETUPCON3 0x23
FILTCON3 0x2B
GAIN3
0x3B
OFFSET3 0x33
SELECT ANALOG INPUT PAIRS
ENABLE THE CHANNEL
SELECT SETUP 0
SELECT PERIPHERAL
FUNCTIONS FOR
ADC CHANNEL
DATA OUTPUT CODING
REFERENCE SOURCE
INPUT BUFFERS
SELECT DIGITAL
FILTER TYPE
AND OUTPUT DATA RATE
GAIN CORRECTION
OFFSET CORRECTION
OPTIONALLY
OPTIONALLY PROGRAMMED
PROGRAMMED
PER SETUP AS REQUIRED
PER SETUP AS REQUIRED
(*FACTORY CALIBRATED)
SINC5 + SINC1
SINC3
SINC3 MAP
12468-046
AIN0
SETUP CONFIG
REGISTERS
Programming the gain and offset registers is optional for any
use case, as indicated by the dashed lines between the register
blocks.
ENHANCED 50Hz AND 60Hz
Figure 50. Two Fully Differential Inputs, Both Using a Single Setup (SETUPCON0; FILTCON0; GAIN0; OFFSET0)
SETUP CONFIG
REGISTERS
FILTER CONFIG
REGISTERS
GAIN REGISTERS*
OFFSET REGISTERS
AIN0
CH0
0x10
SETUPCON0 0x20
FILTCON0 0x28
GAIN0
0x38
OFFSET0 0x30
AIN1
CH1
0x11
SETUPCON1 0x21
FILTCON1 0x29
GAIN1
0x39
OFFSET1 0x31
AIN2
CH2
0x12
SETUPCON2 0x22
FILTCON2 0x2A
GAIN2
0x3A
OFFSET2 0x32
AIN3
CH3
0x13
SETUPCON3 0x23
FILTCON3 0x2B
GAIN3
0x3B
OFFSET3 0x33
AIN4
SELECT PERIPHERAL
FUNCTIONS FOR
ADC CHANNEL
DATA OUTPUT CODING
REFERENCE SOURCE
INPUT BUFFERS
SELECT DIGITAL
FILTER TYPE
AND OUTPUT DATA RATE
SINC5 + SINC1
SINC3
SINC3 MAP
GAIN CORRECTION
OFFSET CORRECTION
OPTIONALLY
OPTIONALLY PROGRAMMED
PROGRAMMED
PER SETUP AS REQUIRED
PER SETUP AS REQUIRED
(*FACTORY CALIBRATED)
ENHANCED 50Hz AND 60Hz
Figure 51. Two Fully Differential Inputs with a Setup per Channel
Rev. A | Page 24 of 60
12468-047
CHANNEL
REGISTERS
Data Sheet
AD7175-2
CHANNEL
REGISTERS
SETUP CONFIG
REGISTERS
required, and the FILTCON0 and FILTCON1 registers are also
programmed as desired. Optional gain and offset correction can
be employed on a per setup basis by programming the GAIN0
and GAIN1 registers and the OFFSET0 and OFFSET1 registers.
In the example shown in Figure 52, the CH0 to CH2 registers
are used. Setting the MSB in each of these registers, the CH_EN0
to CH_EN2 bits enable the three combinations via the crosspoint
mux. When the AD7175-2 converts, the sequencer transitions
in ascending sequential order from CH0 to CH1 to CH2 before
looping back to CH0 to repeat the sequence.
FILTER CONFIG
REGISTERS
GAIN REGISTERS*
AIN0
CH0
0x10
SETUPCON0 0x20
FILTCON0 0x28
GAIN0
AIN1
CH1
0x11
SETUPCON1 0x21
FILTCON1 0x29
AIN2
CH2
0x12
SETUPCON2 0x22
FILTCON2 0x2A
AIN3
CH3
0x13
SETUPCON3 0x23
FILTCON3 0x2B
AIN4
SELECT ANALOG INPUT PARTS
ENABLE THE CHANNEL
SELECT SETUP
SELECT PERIPHERAL
FUNCTIONS FOR
ADC CHANNEL
DATA OUTPUT CODING
REFERENCE SOURCE
INPUT BUFFERS
SELECT DIGITAL
FILTER TYPE
AND OUTPUT DATA RATE
OFFSET0 0x30
GAIN1
0x39
OFFSET1 0x31
GAIN2
0x3A
OFFSET2 0x32
GAIN3
0x3B
OFFSET3 0x33
GAIN CORRECTION
OFFSET CORRECTION
OPTIONALLY
OPTIONALLY PROGRAMMED
PROGRAMMED
PER SETUP AS REQUIRED
PER SETUP AS REQUIRED
(*FACTORY CALIBRATED)
SINC5 + SINC1
SINC3
SINC3 MAP
ENHANCED 50Hz AND 60Hz
Figure 52. Mixed Differential and Single-Ended Configuration Using Multiple Shared Setups
Rev. A | Page 25 of 60
OFFSET REGISTERS
0x38
12468-048
Figure 52 shows an example of how the channel registers span
between the analog input pins and the setup configurations
downstream. In this example, one differential input and two singleended inputs are required. The single-ended inputs are the
AIN2/AIN4 and AIN3/AIN4 combinations. The differential input
pairs is AIN0/AIN1and uses Setup 0. The two single-ended input
pairs are set up as diagnostics; therefore, use a separate setup
from the differential input but share a setup between them,
Setup 1. Given that two setups are selected for use, the
SETUPCON0 and SETUPCON1 registers are programmed as
AD7175-2
Data Sheet
CIRCUIT DESCRIPTION
BUFFERED ANALOG INPUT
AVDD1
The AD7175-2 has true rail-to-rail, integrated, precision unity
gain buffers on both ADC analog inputs. The buffers provide
the benefit of giving the user high input impedance with only
30 nA typical input current, allowing high impedance sources
to be connected directly to the analog inputs. The buffers fully
drive the internal ADC switch capacitor sampling network,
simplifying the analog front-end circuit requirements while
consuming a very efficient 2.9 mA typical per buffer. Each analog
input buffer amplifier is fully chopped, meaning that it minimizes
the offset error drift and 1/f noise of the buffer. The 1/f noise
profile of the ADC and buffer combined is shown in Figure 53.
AIN0
AVSS
AVDD1
Ø1
+IN
AIN1
CS1
AVSS
Ø2
AVDD1
Ø2
AIN2
CS2
AVSS
–IN
AVDD1
Ø1
AIN3
0
AVSS
AVDD1
–50
–100
12468-056
AMPLITUDE (dB)
AIN4
AVSS
Figure 54. Simplified Analog Input Circuit
–150
The CS1 and CS2 capacitors have a magnitude in the order of a
number of picofarads each. This capacitance is the combination
of both the sampling capacitance and the parasitic capacitance.
–200
1
10
100
1k
10k
FREQUENCY (Hz)
12468-259
Fully Differential Inputs
–250
0.1
Figure 53. Shorted Input FFT (Analog Input Buffers Enabled)
The analog input buffers do not suffer from linearity
degradation when operating at the rails, unlike many discrete
amplifiers. When operating at or close to the AVDD1 and AVSS
supply rails, there is an increase in input current. This increase
is most notable at higher temperatures. Figure 42 and Figure 43
show the input current for various conditions. With the analog
input buffers disabled, the average input current to the AD7175-2
changes linearly with the differential input voltage at a rate of
48 µA/V.
CROSSPOINT MULTIPLEXER
There are five analog input pins: AIN0, AIN1, AIN2, AIN3, and
AIN4. Each of these pins connects to the internal crosspoint
multiplexer. The crosspoint multiplexer enables any of these inputs
to be configured as an input pair, either single-ended or fully
differential. The AD7175-2 can have up to four active channels.
When more than one channel is enabled, the channels are
automatically sequenced in order from the lowest enabled channel
number to the highest enabled channel number. The output of
the multiplexer is connected to the input of the integrated true
rail-to-rail buffers. These can be bypassed and the multiplexer
output can be directly connected to the switched-capacitor input
of the ADC. The simplified analog input circuit is shown in
Figure 54.
Because the AIN0 to AIN4 analog inputs are connected to a
crosspoint multiplexer, any combination of signals can be used
to create an analog input pair. This (what does?) allows the user
to select two fully differential inputs or four single-ended
inputs.
If two fully differential input paths are connected to the AD7175-2,
using AIN0/AIN1 as one differential input pair and AIN2/AIN3
as the second differential input pair is recommended. This is
due to the relative locations of these pins to each other. Decouple all
analog inputs to AVSS.
Single-Ended Inputs
The user can also choose to measure four different single-ended
analog inputs. In this case, each of the analog inputs is converted
as the difference between the single-ended input to be
measured and a set analog input common pin. Because there is
a crosspoint multiplexer, the user can set any of the analog inputs
as the common pin. An example of such a scenario is to connect
the AIN4 pin to AVSS or to the REFOUT voltage (that is, AVSS
+ 2.5 V) and select this input when configuring the crosspoint
multiplexer. When using the AD7175-2 with single-ended
inputs, the INL specification is degraded.
Rev. A | Page 26 of 60
Data Sheet
AD7175-2
AD7175-2 REFERENCE
output for stability purposes. The output is then connected to a
4.7 µF capacitor, which acts as a reservoir for any dynamic
charge required by the ADC, and followed by a 0.1 µF
decoupling capacitor at the REF+ input. This capacitor is placed
as close as possible to the REF+ and REF− pins. The REF− pin
is connected directly to the AVSS potential. On power-up of the
AD7175-2, the internal reference is enabled by default and is
output on the REFOUT pin. When an external reference is used
instead of the internal reference to supply the AD7175-2,
attention must be paid to the output of the REFOUT pin. If the
internal reference is not being used elsewhere in the application,
ensure that the REFOUT pin is not hardwired to AVSS because
this draws a large current on power-up. On power-up, if the
internal reference is not being used, write to the ADC mode
register, disabling the internal reference. This is controlled by
the REF_EN bit (Bit 15) in the ADC mode register, which is
shown in Table 18.
The AD7175-2 offers the user the option of either supplying an
external reference to the REF+ and REF− pins of the device or
allowing the use of the internal 2.5 V, low noise, low drift reference.
Select the reference source to be used by the analog input by setting
the REF_SELx bits (Bits[5:4]) in the setup configuration registers
appropriately. The structure of the Setup Configuration 0 register
is shown in Table 17. The AD7175-2 defaults on power-up to
use the internal 2.5 V reference.
External Reference
The AD7175-2 has a fully differential reference input applied
through the REF+ and REF− pins. Standard low noise, low drift
voltage references, such as the ADR445, ADR444, and ADR441,
are recommended for use. Apply the external reference to the
AD7175-2 reference pins as shown in Figure 55. Decouple the
output of any external reference to AVSS. As shown in Figure 55,
the ADR445 output is decoupled with a 0.1 µF capacitor at its
AD7175-2
5.5V TO 18V
ADR4452
0.1µF
0.1µF
5V VREF
1
4.7µF
1
1
3
REF+
2
REF–
0.1µF
1
1ALL DECOUPLING IS TO AVSS.
2ANY OF THE ADR44x FAMILY OF
REFERENCES CAN BE USED.
THE ADR444 AND ADR441 BOTH ENABLE REUSE OF THE 5V ANALOG SUPPLY
NEEDED FOR AVDD1 TO POWER THE REFERENCE VIN.
12468-159
1
Figure 55. External Reference ADR445 Connected to AD7175-2 Reference Pins
Table 17. Setup Configuration 0 Register
Reg.
0x20
Name
SETUPCON0
Bits
[15:8]
[7:0]
Bit 7
Bit 6
Reserved
BURNOUT_EN0 Reserved
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
BI_UNIPOLAR0 REFBUF0+ REFBUF0− AINBUF0+ AINBUF0−
REF_SEL0
Reserved
Reset RW
0x1320 RW
Table 18. ADC Mode Register
Reg.
0x01
Name
ADCMODE
Bits
[15:8]
[7:0]
Bit 7
REF_EN
Reserved
Bit 6
HIDE_DELAY
Bit 5
SING_CYC
Mode
Bit 4
Bit 3
Reserved
Rev. A | Page 27 of 60
Bit 2
CLOCKSEL
Bit 1
Bit 0
Delay
Reserved
Reset
0x8000
RW
RW
AD7175-2
Data Sheet
Internal Reference
The AD7175-2 includes its own low noise, low drift voltage
reference. The internal reference has a 2.5 V output. The internal
reference is output on the REFOUT pin after the REF_EN bit in
the ADC mode register is set and is decoupled to AVSS with a
0.1 µF capacitor. The AD7175-2 internal reference is enabled by
default on power-up and is selected as the reference source for
the ADC. When using the internal reference, the INL performance
is degraded as shown in Figure 23.
The REFOUT signal is buffered before being output to the pin.
The signal can be used externally in the circuit as a common-mode
source for external amplifier configurations.
BUFFERED REFERENCE INPUT
The AD7175-2 has true rail-to-rail, integrated, precision unity
gain buffers on both ADC reference inputs. The buffers provide
the benefit of giving the user high input impedance and allow
high impedance external sources to be directly connected to the
reference inputs. The integrated reference buffers can fully drive
the internal reference switch capacitor sampling network,
simplifying the reference circuit requirements while consuming
a very efficient 2.9 mA typical per buffer. Each reference input
buffer amplifier is fully chopped, meaning that it minimizes the
offset error drift and 1/f noise of the buffer. When using an
external reference, such as the ADR445, ADR444, and ADR441,
these buffers are not required because these references, with
proper decoupling, can drive the reference inputs directly.
the IOVDD logic level. Use of this option can affect the dc
performance of the AD7175-2 due to the disturbance
introduced by the output driver. The extent to which the
performance is affected depends on the IOVDD voltage supply.
Higher IOVDD voltages create a wider logic output swing from
the driver and affect performance to a greater extent. This effect
is further exaggerated if the IOSTRENGTH bit is set at higher
IOVDD levels (see Table 28 for more information).
External Crystal
If higher precision, lower jitter clock sources are required, the
AD7175-2 can use an external crystal to generate the master
clock. The crystal is connected to the XTAL1 and
XTAL2/CLKIO pins. A recommended crystal for use is the FA20H—a 16 MHz, 10 ppm, 9 pF crystal from Epson-Toyocom—
which is available in a surface-mount package. As shown in
Figure 56, insert two capacitors from the traces connecting the
crystal to the XTAL1 and XTAL2/CLKIO pins. These capacitors
allow for circuit tuning. Connect these capacitors to the DGND
pin. The value for these capacitors depends on the length and
capacitance of the trace connections between the crystal and the
XTAL1 and XTAL2/CLKIO pins. Therefore, the values of these
capacitors differ depending on the printed circuit board (PCB)
layout and the crystal employed.
AD7175-2
Cx1
CLOCK SOURCE
XTAL2/CLKIO 10
*
*DECOUPLE TO DGND.
12468-160
Cx2
The AD7175-2 uses a nominal master clock of 16 MHz. The
AD7175-2 can source its sampling clock from one of three
sources:
•
•
•
*
XTAL1 9
Figure 56. External Crystal Connections
Internal oscillator
External crystal
External clock source
All output data rates listed in the data sheet relate to a master
clock rate of 16 MHz. Using a lower clock frequency from, for
instance, an external source scales any listed data rate
proportionally. To achieve the specified data rates, particularly
rates for rejection of 50 Hz and 60 Hz, use a 16 MHz clock. The
source of the master clock is selected by setting the CLOCKSEL
bits (Bits[3:2]) in the ADC mode register as shown in Table 18.
The default operation on power-up and reset of the AD7175-2
is to operate with the internal oscillator. It is possible to fine
tune the output data rate and filter notch at low output data
rates using the SINC3_MAPx bit. See the Sinc3 Filter section
for more information.
Internal Oscillator
The internal oscillator runs at 16 MHz and can be used as the
ADC master clock. It is the default clock source for the AD7175-2
and is specified with an accuracy of ±2.5%.
There is an option to allow the internal clock oscillator to be
output on the XTAL2/CLKIO pin. The clock output is driven to
The external crystal circuitry can be sensitive to the SCLK
edges, depending on SCLK frequency, IOVDD voltage, crystal
circuitry layout, and the crystal used. During crystal startup, any
disturbances caused by the SLCK edges may cause double edges
on the crystal input, resulting in invalid conversions until the
crystal voltage has reached a high enough level such that any
interference from the SCLK edges is insufficient to cause double
clocking. This double clocking can be avoided by ensuring that
the crystal circuitry has reached a sufficient voltage level after
startup before applying any SCLK.
Due to the nature of the crystal circuitry, it is therefore
recommended that empirical testing of the circuit b performed
under the required conditions, with the final PCB layout and
crystal, to ensure correct operation.
External Clock
The AD7175-2 can also use an externally supplied clock. In
systems where this is desirable, the external clock is routed to
the XTAL2/CLKIO pin. In this configuration, the
XTAL2/CLKIO pin accepts the externally sourced clock and
routes it to the modulator. The logic level of this clock input is
defined by the voltage applied to the IOVDD pin.
Rev. A | Page 28 of 60
Data Sheet
AD7175-2
DIGITAL FILTERS
SINC3 FILTER
The AD7175-2 has three flexible filter options to allow
optimization of noise, settling time, and rejection:
The sinc3 filter achieves the best single-channel noise performance
at lower rates and is, therefore, most suitable for single-channel
applications. The sinc3 filter always has a settling time equal to
Sinc5 + sinc1 filter
Sinc3 filter
Enhanced 50 Hz and 60 Hz rejection filters
SINC1
Figure 59 shows the frequency domain filter response for the
sinc3 filter. The sinc3 filter has good roll-off over frequency and
has wide notches for good notch frequency rejection.
50Hz AND 60Hz
POSTFILTER
0
12468-058
SINC5
tSETTLE = 3/Output Data Rate
SINC3
–10
–20
Figure 57. Digital Filter Block Diagram
FILTER GAIN (dB)
–30
The filter and output data rate are configured by setting the
appropriate bits in the filter configuration register for the
selected setup. Each channel can use a different setup and
therefore, a different filter and output data rate. See the Register
Details section for more information.
SINC5 + SINC1 FILTER
–50
–60
–70
–80
–90
The sinc5 + sinc1 filter is targeted at multiplexed applications
and achieves single cycle settling at output data rates of 10 kSPS and
lower. The sinc5 block output is fixed at the maximum rate of
250 kSPS, and the sinc1 block output data rate can be varied to
control the final ADC output data rate. Figure 58 shows the
frequency domain response of the sinc5 + sinc1 filter at a 50 SPS
output data rate. The sinc5 + sinc1 filter has a slow roll-off over
frequency and narrow notches.
0
–20
FILTER GAIN (dB)
–40
–40
–100
–110
–120
0
50
The output data rates with the accompanying settling time and
rms noise for the sinc3 filter are shown in Table 21 and Table 22. It
is possible to finely tune the output data rate for the sinc3 filter by
setting the SINC3_MAPx bit in the filter configuration registers.
If this bit is set, the mapping of the filter register changes to directly
program the decimation rate of the sinc3 filter. All other options
are eliminated. The data rate when on a single channel can be
calculated using the following equation:
Output Data Rate =
–120
0
50
100
150
FREQUENCY (Hz)
12468-059
–100
Figure 58. Sinc5 + Sinc1 Filter Response at 50 SPS ODR
The output data rates with the accompanying settling time and
rms noise for the sinc5 + sinc1 filter are shown in Table 19 and
Table 20.
150
Figure 59. Sinc3 Filter Response
–60
–80
100
FREQUENCY (Hz)
12468-060
•
•
•
f MOD
32 × FILTCONx[14:0]
where:
fMOD is the modulator rate (MCLK/2) and is 8 MHz for a
16 MHz MCLK.
FILTCONx[14:0] are the contents on the filter configuration
registers excluding the MSB.
For example, an output data rate of 50 SPS can be achieved with
SINC3_MAPx enabled by setting the FILTCONx[14:0] bits to a
value of 5000.
Rev. A | Page 29 of 60
AD7175-2
Data Sheet
The AD7175-2 can be configured by setting the SING_CYC bit
in the ADC mode register so that only fully settled data is output,
thus effectively putting the ADC into a single cycle settling mode.
This mode achieves single cycle settling by reducing the output
data rate to be equal to the settling time of the ADC for the selected
output data rate. This bit has no effect with the sinc5 + sinc1
filter at output data rates of 10 kSPS and lower.
Figure 61 shows the same step on the analog input but with
single cycle settling enabled. The analog input requires at least a
single cycle for the output to be fully settled. The output data
rate, as indicated by the RDY signal, is now reduced to equal the
settling time of the filter at the selected output data rate.
ANALOG
INPUT
FULLY
SETTLED
ADC
OUTPUT
Figure 60 shows a step on the analog input with this mode
disabled and the sinc3 filter selected. The analog input requires
at least three cycles after the step change for the output to reach
the final settled value.
12468-062
SINGLE CYCLE SETTLING
tSETTLE
Figure 61. Step Input with Single Cycle Settling
ANALOG
INPUT
FULLY
SETTLED
12468-061
ADC
OUTPUT
1/ODR
Figure 60. Step Input Without Single Cycle Settling
Table 19. Output Data Rate, Settling Time, and Noise Using the Sinc5 + Sinc1 Filter with Input Buffers Disabled
Default Output
Data Rate (SPS);
SING_CYC = 0 and
Single Channel
Enabled1
250,000
125,000
62,500
50,000
31,250
25,000
15,625
10,000
5000
2500
1000
500
397.5
200
100
59.92
49.96
20
16.66
10
5
1
2
Output Data Rate
(SPS/Channel);
SING_CYC = 1 or with
Multiple Channels
Enabled1
50,000
41,667
31,250
27,778
20,833
17,857
12,500
10,000
5000
2500
1000
500.0
397.5
200.0
100
59.92
49.96
20.00
16.66
10.00
5.00
Settling
Time1
20 µs
24 µs
32 µs
36 µs
48 µs
56 µs
80 µs
100 µs
200 µs
400 µs
1.0 ms
2.0 ms
2.516 ms
5.0 ms
10 ms
16.67 ms
20.016 ms
50.0 ms
60.02 ms
100 ms
200 ms
Notch
Frequency
(Hz)
250,000
125,000
62,500
50,000
31,250
25,000
15,625
11,905
5435
2604
1016
504
400.00
200.64
100.16
59.98
50.00
20.01
16.66
10.00
5.00
Noise
(µV rms)
8.7
7.2
5.5
5
4
3.6
2.9
2.5
1.7
1.2
0.77
0.57
0.5
0.36
0.25
0.19
0.18
0.11
0.1
0.08
0.07
Effective
Resolution with
5 V Reference
(Bits)
20.1
20.4
20.8
20.9
21.3
21.4
21.7
21.9
22.5
23.0
23.6
24
24
24
24
24
24
24
24
24
24
Noise
(µV p-p)2
65
60
43
41
32
29
22
18.3
12
8.2
5.2
3.2
3
2
1.3
1.1
0.95
0.6
0.45
0.4
0.34
Peak-to-Peak
Resolution with
5 V Reference
(Bits)
17.2
17.3
17.8
17.9
18.3
18.4
18.8
19.1
19.7
20.2
20.9
21.6
21.7
22.3
22.9
23.1
23.3
24
24
24
24
The settling time is rounded to the nearest microsecond. This is reflected in the output data rate and channel switching rate. Channel switching rate = 1 ÷ settling time.
1000 samples.
Rev. A | Page 30 of 60
Data Sheet
AD7175-2
Table 20. Output Data Rate, Settling Time, and Noise Using the Sinc5 + Sinc1 Filter with Input Buffers Enabled
Default Output Data
Rate (SPS);
SING_CYC = 0 and
Single Channel
Enabled1
250,000
125,000
62,500
50,000
31,250
25,000
15,625
10,000
5000
2500
1000
500
397.5
200
100
59.92
49.96
20
16.66
10
5
1
2
Output Data Rate
(SPS/Channel);
SING_CYC = 1 or
with Multiple
Channels Enabled1
50,000
41,667
31,250
27,778
20,833
17,857
12,500
10,000
5000
2500
1000
500.0
397.5
200.0
100
59.92
49.96
20.00
16.66
10.00
5.00
Settling
Time1
20 µs
24 µs
32 µs
36 µs
48 µs
56 µs
80 µs
100 µs
200 µs
400 µs
1.0 ms
2.0 ms
2.516 ms
5.0 ms
10 ms
16.67 ms
20.016 ms
50.0 ms
60.02 ms
100 ms
200 ms
Notch
Frequency
(Hz)
250,000
125,000
62,500
50,000
31,250
25,000
15,625
11,905
5435
2604
1016
504
400.00
200.64
100.16
59.98
50.00
20.01
16.66
10.00
5.00
Noise
(µV rms)
9.8
8.4
6.4
5.9
4.8
4.3
3.4
3
2.1
1.5
0.92
0.68
0.6
0.43
0.32
0.23
0.2
0.14
0.13
0.1
0.07
Effective
Resolution with
5 V Reference
(Bits)
20
20.2
20.6
20.7
21
21.1
21.5
21.7
22.2
22.7
23.4
23.8
24
24
24
24
24
24
24
24
24
Noise
(µV p-p)2
85
66
55
49
39
33
26
23
16
10
5.7
3.9
3.7
2.2
1.7
1.2
1
0.75
0.66
0.47
0.32
Peak-to-Peak
Resolution with
5 V Reference
(Bits)
16.8
17.2
17.5
17.6
18.0
18.2
18.6
18.7
19.3
19.9
20.7
21.3
21.4
22.1
22.5
23
23.3
23.7
23.9
24
24
The settling time is rounded to the nearest microsecond. This is reflected in the output data rate and channel switching rate. Channel switching rate = 1 ÷ settling time.
1000 samples.
Rev. A | Page 31 of 60
AD7175-2
Data Sheet
Table 21. Output Data Rate, Settling Time, and Noise Using the Sinc3 Filter with Input Buffers Disabled
Default Output
Data Rate (SPS);
SING_CYC = 0 and
Single Channel
Enabled1
250,000
125,000
62,500
50,000
31,250
25,000
15,625
10,000
5000
2500
1000
500
400
200
100
60
50
20
16.67
10
5
1
2
Output Data Rate
(SPS/Channel);
SING_CYC = 1 or with
Multiple Channels
Enabled1
83,333
41,667
20,833
16,667
10,417
8333
5208
3333
1667
833
333.3
166.7
133.3
66.7
33.33
19.99
16.67
6.67
5.56
3.33
1.67
Settling
Time1
12 µs
24 µs
48 µs
60 µs
96 µs
120 µs
192 µs
300 µs
6 µs
1.2 ms
3 ms
6 ms
7.5 ms
15 ms
30 ms
50.02 ms
60 ms
150 ms
180 ms
300 ms
600 ms
Notch
Frequency
(Hz)
250,000
125,000
62,500
50,000
31,250
25,000
15,625
10,000
5000
2500
1000
500
400
200
100
59.98
50
20
16.67
10
5
Noise
(µV rms)
210
28
5.2
4.2
3.2
2.9
2.2
1.8
1.3
0.91
0.56
0.44
0.4
0.25
0.2
0.13
0.13
0.08
0.07
0.06
0.05
Effective
Resolution with
5 V Reference
(Bits)
15.5
18.4
20.9
21.2
21.6
21.7
22.1
22.4
22.9
23.4
24
24
24
24
24
24
24
24
24
24
24
Noise
(µV p-p)2
1600
200
40
34
26
23
17
14
9.5
6
3.9
2.5
2.3
1.4
1
0.8
0.7
0.42
0.37
0.28
0.21
Peak-to-Peak
Resolution with
5 V Reference
(Bits)
12.6
15.6
17.9
18.2
18.6
18.7
19.2
19.4
20
20.7
21.3
21.9
22.1
22.8
23.3
23.6
23.8
24
24
24
24
The settling time is rounded to the nearest microsecond. This is reflected in the output data rate and channel switching rate. Channel switching rate = 1 ÷ settling time.
1000 samples.
Rev. A | Page 32 of 60
Data Sheet
AD7175-2
Table 22. Output Data Rate, Settling Time, and Noise Using the Sinc3 Filter with Input Buffers Enabled
Default Output
Data Rate (SPS);
SING_CYC = 0 and
Single Channel
Enabled1
250,000
125,000
62,500
50,000
31,250
25,000
15,625
10,000
5000
2500
1000
500
400
200
100
60
50
20
16.67
10
5
1
2
Output Data Rate
(SPS/Channel);
SING_CYC = 1 or with
Multiple Channels
Enabled1
83,333
41,667
20,833
16,667
10,417
8333
5208
3333
1667
833
333.3
166.7
133.3
66.7
33.33
19.99
16.67
6.67
5.56
3.33
1.67
Settling
Time1
12 µs
24 µs
48 µs
60 µs
96 µs
120 µs
192 µs
300 µs
6 µs
1.2 ms
3 ms
6 ms
7.5 ms
15 ms
30 ms
50.02ms
60 ms
150 ms
180 ms
300 ms
600 ms
Notch
Frequency
(Hz)
250,000
125,000
62,500
50,000
31,250
25,000
15,625
10,000
5000
2500
1000
500
400
200
100
59.98
50
20
16.67
10
5
Noise
(µV rms)
210
28
5.8
4.9
3.8
3.4
2.6
2.1
1.5
1.1
0.71
0.52
0.41
0.32
0.2
0.17
0.15
0.13
0.12
0.1
0.08
Effective
Resolution with
5 V Reference
(Bits)
15.5
18.4
20.7
21
21.3
21.5
21.9
22.2
22.7
23.1
23.7
24
24
24
24
24
24
24
24
24
24
Noise
(µV p-p)2
1600
210
48
41
30
26
18
16
11
7
4.5
3
2.7
1.8
1.2
1.1
0.83
0.61
0.6
0.55
0.35
Peak-to-Peak
Resolution with
5 V Reference
(Bits)
12.6
15.5
17.7
17.9
18.3
18.6
19.1
19.3
19.8
20.4
21.1
21.7
21.8
22.4
23
23.1
23.5
24
24
24
24
The settling time is rounded to the nearest microsecond. This is reflected in the output data rate and channel switching rate. Channel switching rate = 1 ÷ settling time.
1000 samples.
Rev. A | Page 33 of 60
AD7175-2
Data Sheet
ENHANCED 50 HZ AND 60 HZ REJECTION FILTERS
The enhanced filters are designed to provide rejection of 50 Hz
and 60 Hz simultaneously and to allow the user to trade off
settling time and rejection. These filters can operate up to
27.27 SPS or can reject up to 90 dB of 50 Hz ± 1 Hz and 60 Hz
± 1 Hz interference. These filters are realized by postfiltering
the output of the sinc5 + sinc1 filter. For this reason, the sinc5 +
sinc1 filter must be selected when using the enhanced filters to
achieve the specified settling time and noise performance. Table 23
shows the output data rates with the accompanying settling
time, rejection, and rms noise. Figure 62 to Figure 69 show the
frequency domain plots of the responses from the enhanced filters.
Table 23. Enhanced Filters Output Data Rate, Noise, Settling Time, and Rejection Using the Enhanced Filters
Output Data Rate
(SPS)
Input Buffers Disabled
27.27
25
20
16.667
Input Buffers Enabled
27.27
25
20
16.667
1
Settling
Time (ms)
Simultaneous Rejection of
50 Hz ± 1 Hz and 60 Hz ± 1 Hz(dB)1
Noise
(µV rms)
Peak-to-Peak
Resolution (Bits)
Comments
36.67
40.0
50.0
60.0
47
62
85
90
0.22
0.2
0.2
0.17
22.7
22.9
22.9
23
See Figure 62 and Figure 65
See Figure 63 and Figure 66
See Figure 64 and Figure 67
See Figure 68 and Figure 69
36.67
40.0
50.0
60.0
47
62
85
90
0.22
0.22
0.21
0.21
22.7
22.7
22.8
22.8
See Figure 62 and Figure 65
See Figure 63 and Figure 66
See Figure 64 and Figure 67
See Figure 68 and Figure 69
Master clock = 16.00 MHz.
Rev. A | Page 34 of 60
AD7175-2
0
–10
–10
–20
–20
–30
–30
–40
–50
–60
–40
–50
–60
–70
–70
–80
–80
–90
–90
–100
–100
40
0
100
200
300
400
500
600
FREQUENCY (Hz)
55
60
65
70
Figure 65. 27.27 SPS ODR, 36.67 ms Settling Time
0
0
–10
–10
–20
–20
–30
FILTER GAIN (dB)
–40
–50
–60
–30
–40
–50
–60
–70
–70
–80
–80
–90
0
100
200
300
400
500
600
FREQUENCY (Hz)
–100
40
12468-065
–100
45
50
55
60
65
70
FREQUENCY (Hz)
12468-066
–90
Figure 66. 25 SPS ODR, 40 ms Settling Time
Figure 63. 25 SPS ODR, 40 ms Settling Time
0
0
–10
–10
–20
–20
FILTER GAIN (dB)
–30
–40
–50
–60
–30
–40
–50
–60
–70
–70
–80
–80
–90
–100
0
100
200
300
400
500
FREQUENCY (Hz)
600
12468-067
–90
–100
40
45
50
55
60
65
FREQUENCY (Hz)
Figure 67. 20 SPS ODR, 50 ms Settling Time
Figure 64. 20 SPS ODR, 50 ms Settling Time
Rev. A | Page 35 of 60
70
12468-068
FILTER GAIN (dB)
50
FREQUENCY (Hz)
Figure 62. 27.27 SPS ODR, 36.67 ms Settling Time
FILTER GAIN (dB)
45
12468-064
FILTER GAIN (dB)
0
12468-063
FILTER GAIN (dB)
Data Sheet
Data Sheet
0
–10
–10
–20
–20
–30
–30
–40
–50
–60
–40
–50
–60
–70
–70
–80
–80
–90
–90
–100
–100
40
0
100
200
300
400
500
FREQUENCY (Hz)
600
Figure 68. 16.667 SPS ODR, 60 ms Settling Time
45
50
55
60
65
FREQUENCY (Hz)
Figure 69. 16.667 SPS ODR, 60 ms Settling Time
Rev. A | Page 36 of 60
70
12468-070
FILTER GAIN (dB)
0
12468-069
FILTER GAIN (dB)
AD7175-2
Data Sheet
AD7175-2
OPERATING MODES
The AD7175-2 has a number of operating modes that can be set
from the ADC mode register and interface mode register (see
Table 27 and Table 28). These modes are as follows and are
described in the following paragraphs:
•
•
•
•
•
•
Continuous conversion mode
Continuous read mode
Single conversion mode
Standby mode
Power-down mode
Calibration modes (three)
CONTINUOUS CONVERSION MODE
Continuous conversion is the default power-up mode. The
AD7175-2 converts continuously, and the RDY bit in the status
register goes low each time a conversion is complete. If CS is low,
the RDY output also goes low when a conversion is complete. To
read a conversion, the user writes to the communications
register, indicating that the next operation is a read of the data
register. When the data-word has been read from the data register,
the DOUT/RDY pin goes high. The user can read this register
additional times, if required. However, the user must ensure that
the data register is not being accessed at the completion of the
next conversion; otherwise, the new conversion word is lost.
When several channels are enabled, the ADC automatically
sequences through the enabled channels, performing one
conversion on each channel. When all channels have been
converted, the sequence starts again with the first channel. The
channels are converted in order from lowest enabled channel to
highest enabled channel. The data register is updated as soon as
each conversion is available. The RDY output pulses low each
time a conversion is available. The user can then read the
conversion while the ADC converts the next enabled channel.
If the DATA_STAT bit in the interface mode register is set to 1,
the contents of the status register, along with the conversion data,
are output each time the data register is read. The status register
indicates the channel to which the conversion corresponds.
CS
0x44
0x44
DIN
DATA
DATA
12468-071
DOUT/RDY
SCLK
Figure 70. Continuous Conversion Mode
Rev. A | Page 37 of 60
AD7175-2
Data Sheet
CONTINUOUS READ MODE
To enable continuous read mode, set the CONTREAD bit in the
interface mode register. When this bit is set, the only serial interface
operations possible are reads from the data register. To exit continuous read mode, issue a dummy read of the ADC data register
command (0x44) while the RDY output is low. Alternatively, apply
a software reset, that is, 64 SCLKs with CS = 0 and DIN = 1.
This resets the ADC and all register contents. These are the only
commands that the interface recognizes after it is placed in
continuous read mode. Hold DIN low in continuous read mode
until an instruction is to be written to the device.
In continuous read mode, it is not required to write to the
communications register before reading ADC data; apply only
the required number of SCLKs after RDY goes low to indicate
the end of a conversion. When the conversion is read, RDY
returns high until the next conversion is available. In this mode,
the data can be read only once. The user must also ensure that
the data-word is read before the next conversion is complete. If
the user has not read the conversion before the completion of
the next conversion or if insufficient serial clocks are applied to
the AD7175-2 to read the data word, the serial output register is
reset shortly before the next conversion is complete, and the
new conversion is placed in the output serial register. The ADC
must be configured for continuous conversion mode to use
continuous read mode.
If multiple ADC channels are enabled, each channel is output
in turn, with the status bits being appended to the data if
DATA_STAT is set in the interface mode register. The status
register indicates the channel to which the conversion corresponds.
CS
0x02
0x0080
DIN
DATA
DATA
DATA
12468-072
DOUT/RDY
SCLK
Figure 71. Continuous Read Mode
Rev. A | Page 38 of 60
Data Sheet
AD7175-2
SINGLE CONVERSION MODE
In single conversion mode, the AD7175-2 performs a single
conversion and is placed in standby mode after the conversion
is complete. The RDY output goes low to indicate the completion
of a conversion. When the data-word has been read from the
data register, DOUT/RDY pin goes high. The data register can
be read several times, if required, even when DOUT/RDY pin has
gone high.
If several channels are enabled, the ADC automatically
sequences through the enabled channels and performs a
conversion on each channel. When a conversion is started, the
DOUT/RDY pin goes high and remains high until a valid
conversion is available and CS is low. As soon as the conversion is
available, the RDY output goes low. The ADC then selects the next
channel and begins a conversion. The user can read the present
conversion while the next conversion is being performed. As soon
as the next conversion is complete, the data register is updated;
therefore, the user has a limited period in which to read the
conversion. When the ADC has performed a single conversion
on each of the selected channels, it returns to standby mode.
If the DATA_STAT bit in the interface mode register is set to 1,
the contents of the status register, along with the conversion, are
output each time the data register is read. The two LSBs of the
status register indicate the channel to which the conversion
corresponds.
CS
0x01
0x8010
0x44
DIN
DATA
12468-073
DOUT/RDY
SCLK
Figure 72. Single Conversion Mode
Rev. A | Page 39 of 60
AD7175-2
Data Sheet
STANDBY AND POWER-DOWN MODES
In standby mode, most blocks are powered down. The LDOs
remain active so that registers maintain their contents. The
internal reference remains active if enabled, and the crystal
oscillator remains active if selected. To power down the
reference in standby mode, set the REF_EN bit in the ADC
mode regsiter to 0. To power down the clock in standby mode,
set the CLOCKSEL bits in the ADC mode register to 00
(internal oscillator).
In power-down mode, all blocks are powered down, including
the LDOs. All registers lose their contents, and the GPIO outputs
are placed in three-state. To prevent accidental entry to powerdown mode, the ADC must first be placed in standby mode.
Exiting power-down mode requires 64 SCLKs with CS = 0 and
DIN = 1, that is, a serial interface reset. A delay of 500 µs is
recommended before issuing a subsequent serial interface
command to allow the LDO to power up.
Figure 19 shows the internal reference settling time after
returning from standby mode (setting REF_EN = 0 and then 1)
and returning from power down.
CALIBRATION
The AD7175-2 allows a two-point calibration to be performed
to eliminate any offset and gain errors. Three calibration modes
are used to eliminate these offset and gain errors on a per setup
basis:
•
•
•
Internal zero-scale calibration mode
System zero-scale calibration mode
System full-scale calibration mode
There is no internal full-scale calibration mode bcause this is
calibrated in the factory at the time of production.
Only one channel can be active during calibration. After each
conversion, the ADC conversion result is scaled using the ADC
calibration registers before being written to the data register.
The default value of the offset register is 0x800000, and the
nominal value of the gain register is 0x555555. The calibration
range of the ADC gain is from 0.4 × VREF to 1.05 × VREF. The
following equations show the calculations that are used. In
unipolar mode, the ideal relationship—that is, not taking into
account the ADC gain error and offset error—is as follows:
 0.75 × V

Gain
IN
Data = 
× 2 23 − ( Offset − 0 x 800000 )  ×
×2
 V
 0 x 400000
REF


In bipolar mode, the ideal relationship—that is, not taking into
account the ADC gain error and offset error—is as follows:
 0.75 × V

Gain
IN
Data = 
× 2 23 − ( Offset − 0 x 800000 )  ×
+ 0 x 800000
 V
 0 x 400000
REF


To start a calibration, write the relevant value to the mode bits
in the ADC mode register. The DOUT/RDY pin and the RDY
bit in the status register go high when the calibration initiates.
When the calibration is complete, the contents of the
corresponding offset or gain register are updated, the RDY bit
in the status register is reset and the RDY output pin returns
low (if CS is low), and the AD7175-2 reverts to standby mode.
During an internal offset calibration, the selected positive
analog input pin is disconnected, and both modulator inputs
are connected internally to the selected negative analog input
pin. For this reason, it is necessary to ensure that the voltage on
the selected negative analog input pin does not exceed the
allowed limits and is free from excessive noise and interference.
System calibrations, however, expect the system zero-scale
(offset) and system full-scale (gain) voltages to be applied to the
ADC pins before initiating the calibration modes. As a result,
errors external to the ADC are removed.
From an operational point of view, treat a calibration like
another ADC conversion. An offset calibration, if required,
must always be performed before a full-scale calibration. Set the
system software to monitor the RDY bit in the status register or
the RDY output to determine the end of a calibration via a
polling sequence or an interrupt-driven routine. All calibrations
require a time equal to the settling time of the selected filter and
output data rate to be completed.
An internal offset calibration, system zero-scale calibration, and
system full-scale calibration can be performed at any output data
rate. Using lower output data rates results in better calibration
accuracy and is accurate for all output data rates. A new offset
calibration is required for a given channel if the reference source
for that channel is changed.
The offset error is typically ±40 µV and an offset calibration
reduces the offset error to the order of the noise. The gain error
is factory calibrated at ambient temperature. Following this
calibration, the gain error is typically ±35 ppm of FSR.
The AD7175-2 provides the user with access to the on-chip
calibration registers, allowing the microprocessor to read the
calibration coefficients of the device and to write its own
calibration coefficients. A read or write of the offset and gain
registers can be performed at any time except during an internal
or self calibration.
Rev. A | Page 40 of 60
Data Sheet
AD7175-2
DIGITAL INTERFACE
Figure 2 and Figure 3 show timing diagrams for interfacing to
the AD7175-2 using CS to decode the device. Figure 2 shows
the timing for a read operation from the AD7175-2, and Figure 3
shows the timing for a write operation to the AD7175-2. It is
possible to read from the data register several times even though
the RDY output returns high after the first read operation.
However, care must be taken to ensure that the read operations are
completed before the next output update occurs. In continuous
read mode, the data register can be read only once.
The serial interface can operate in 3-wire mode by tying CS low.
In this case, the SCLK, DIN, and DOUT/RDY pins are used to
communicate with the AD7175-2. The end of the conversion
can also be monitored using the RDY bit in the status register.
The AD7175-2 can be reset by writing 64 SCLKs with CS = 0
and DIN = 1. A reset returns the interface to the state in which it
expects a write to the communications register. This operation
resets the contents of all registers to their power-on values.
Following a reset, allow a period of 500 µs before addressing the
serial interface.
x8 + x2 + x + 1
During read operations, the user can select between this
polynomial and a simpler XOR function. The XOR function
requires less time to process on the host microcontroller than
the polynomial-based checksum. The CRC_EN bits in the
interface mode register enable and disable the checksum and
allow the user to select between the polynomial check and the
simple XOR check.
The checksum is appended to the end of each read and write
transaction. The checksum calculation for the write transaction
is calculated using the 8-bit command word and the 8-bit to
24-bit data. For a read transaction, the checksum is calculated
using the command word and the 8-bit to 32-bit data output.
Figure 73 and Figure 74 show SPI write and read transactions,
respectively.
8-BIT COMMAND
UP TO 24-BIT INPUT
8-BIT CRC
CS
DATA
CRC
CS
DIN
12468-074
The DOUT/RDY pin also functions as a data ready signal, with
the output going low if CS is low when a new data-word is
available in the data register. The RDY output is reset high when
a read operation from the data register is complete. The RDY
output also goes high before updating the data register to
indicate when not to read from the device to ensure that a data
read is not attempted while the register is being updated. Take
care to avoid reading from the data register when the RDY
output is about to go low. The best method to ensure that no data
read occurs is to always monitor the RDY output; start reading
the data register as soon as the RDY output goes low; and
ensure a sufficient SCLK rate, such that the read is completed
before the next conversion result. CS is used to select a device. It
can be used to decode the AD7175-2 in systems where several
components are connected to the serial bus.
For CRC checksum calculations during a write operation, the
following polynomial is always used:
SCLK
Figure 73. SPI Write Transaction with CRC
8-BIT COMMAND
UP TO 32-BIT INPUT
8-BIT CRC
CS
DIN
DOUT/
RDY
CMD
DATA
CRC
SCLK
12468-075
The programmable functions of the AD7175-2 are controlled via
the SPI serial interface. The serial interface of the AD7175-2
consists of four signals: CS, DIN, SCLK, and DOUT/RDY. The
DIN input is used to transfer data into the on-chip registers, and
DOUT output is used to access data from the on-chip registers.
SCLK is the serial clock input for the device, and all data transfers
(either on DIN input or on DOUT output) occur with respect to
the SCLK signal.
Figure 74. SPI Read Transaction with CRC
If checksum protection is enabled when continuous read mode
is active, an implied read data command of 0x44 before every
data transmission must be accounted for when calculating the
checksum value. This implied read data command ensures a
nonzero checksum value even if the ADC data equals 0x000000.
CHECKSUM PROTECTION
The AD7175-2 has a checksum mode that can be used to
improve interface robustness. Using the checksum ensures that
only valid data is written to a register and allows data read from
a register to be validated. If an error occurs during a register
write, the CRC_ERROR bit is set in the status register. However,
to ensure that the register write was successful, read back the
register and verify the checksum.
Rev. A | Page 41 of 60
AD7175-2
Data Sheet
CRC CALCULATION
Polynomial
The checksum, which is eight bits wide, is generated using the
polynomial
x8 + x2 + x + 1
To generate the checksum, the data is left shifted by eight bits to
create a number ending in eight Logic 0s. The polynomial is
aligned so that its MSB is adjacent to the leftmost Logic 1 of the
data. An XOR (exclusive OR) function is applied to the data to
produce a new, shorter number. The polynomial is again aligned
so that its MSB is adjacent to the leftmost Logic 1 of the new result,
and the procedure is repeated. This process repeats until the
original data is reduced to a value less than the polynomial.
This is the 8-bit checksum.
Example of a Polynomial CRC Calculation—24-Bit Word: 0x654321 (Eight Command Bits and 16-Bit Data)
An example of generating the 8-bit checksum using the polynomial based checksum is as follows:
Initial value
011001010100001100100001
x8 + x2 + x + 1
01100101010000110010000100000000
left shifted eight bits
=
polynomial
100000111
100100100000110010000100000000
100000111
XOR result
polynomial
100011000110010000100000000
100000111
XOR result
polynomial
11111110010000100000000
100000111
XOR result
polynomial value
1111101110000100000000
100000111
XOR result
polynomial value
111100000000100000000
100000111
XOR result
polynomial value
11100111000100000000
100000111
XOR result
polynomial value
1100100100100000000
100000111
XOR result
polynomial value
100101010100000000
100000111
XOR result
polynomial value
101101100000000
100000111
1101011000000
100000111
101010110000
100000111
1010001000
100000111
10000110
XOR result
polynomial value
XOR result
polynomial value
XOR result
polynomial value
XOR result
polynomial value
checksum = 0x86
Rev. A | Page 42 of 60
Data Sheet
AD7175-2
XOR Calculation
The checksum, which is 8 bits wide, is generated by splitting the data into bytes and then performing an XOR of the bytes.
Example of an XOR Calculation—24-Bit Word: 0x654321 (Eight Command Bits and 16-Bit Data)
Using the previous example, divide into three bytes: 0x65, 0x43, and 0x21
01100101
0x65
01000011
0x43
00100110
XOR result
00100001
0x21
00000111
CRC
Rev. A | Page 43 of 60
AD7175-2
Data Sheet
INTEGRATED FUNCTIONS
The AD7175-2 has integrated functions that improve the
usefulness of a number of applications as well as serve
diagnostic purposes in safety conscious applications.
GENERAL-PURPOSE I/O
The AD7175-2 has two general-purpose digital input/output pins:
GPIO0 and GPIO1. They are enabled using the IP_EN0/IP_EN1
bits or the OP_EN0/OP_EN1 bits in the GPIOCON register. When
the GPIO0 or GPIO1 pin is enabled as an input, the logic level at
the pin is contained in the GP_DATA0 or GP_DATA1 bit,
respectively. When the GPIO0 or GPIO1 pin is enabled as an
output, the GP_ DATA0 or GP_DATA1 bits, respectively,
determine the logic level output at the pin. The logic levels for
these pins are referenced to AVDD1 and AVSS; therefore, outputs
have an amplitude of 5 V.
The effect on the noise performance depends on the delay time
compared to the conversion time. It is possible to absorb the
delay only for output data rates less than 10 kSPS with the
exception of the following four rates, which cannot absorb any
delay: 397.5 SPS, 59.92 SPS, 49.96 SPS, and 16.66 SPS.
16-BIT/24-BIT CONVERSIONS
By default, the AD7175-2 generates 24-bit conversions.
However, the width of the conversions can be reduced to 16 bits.
Setting the WL16 bit in the interface mode register to 1 rounds
all data conversions to 16 bits. Clearing this bit sets the width of
the data conversions to 24 bits.
DOUT_RESET
Both GPIOs and the SYNC/ERROR pin, when set as generalpurpose outputs, have an active pull-up.
The serial interface uses a shared DOUT/RDY pin. By default,
this pin outputs the RDY signal. During a data read, this pin
outputs the data from the register being read. After the read is
complete, the pin reverts to outputting the RDY signal after a
short fixed period of time (t7). However, this time may be too
short for some microcontrollers and can be extended until
the CS pin is brought high by setting the DOUT_RESET bit in
the interface mode register to 1. This means that CS must be
used to frame each read operation and compete the serial
interface transaction.
EXTERNAL MULTIPLEXER CONTROL
SYNCHRONIZATION
If an external multiplexer is used to increase the channel count,
the multiplexer logic pins can be controlled via the AD7175-2
GPIOx pins. With the MUX_IO bit, the GPIOx timing is
controlled by the ADC; therefore, the channel change is
synchronized with the ADC, eliminating any need for external
synchronization.
Normal Synchronization
The SYNC/ERROR pin can also be used as a general-purpose
output. When ERR_EN bits in the GPIOCON register are set to
11, the SYNC/ERROR pin operates as a general-purpose output.
In this configuration, the ERR_DAT bit in the GPIOCON register
determines the logic level output at the pin. The logic level for the
pin is referenced to IOVDD and DGND.
DELAY
It is possible to insert a programmable delay before the AD7175-2
begins to take samples. This delay allows an external amplifier
or multiplexer to settle and can also alleviate the specification
requirements for the external amplifier or multiplexer. Eight
programmable settings, ranging from 0 µs to 1 ms, can be set
using the delay bits in the ADC mode register (Register 0x01,
Bits[10:8]).
If a delay greater than 0 µs is selected and the HIDE_DELAY bit
in the ADC mode register is set to 0, this delay is added to the
conversion time, regardless of selected output data rate.
When using the sinc5 + sinc1 filter, it is possible to hide this
delay such that the output data rate remains the same as the output
data rate without the delay enabled. If the HIDE_DELAY bit is
set to 1 and the selected delay is less than half of the conversion
time, the delay can be absorbed by reducing the number of
averages the digital filter performs, which keeps the conversion
time the same but can affect the noise performance.
When the SYNC_EN bit in the GPIOCON register is set to 1,
the SYNC/ERROR pin functions as a synchronization input.
The SYNC input lets the user reset the modulator and the
digital filter without affecting any of the setup conditions on the
device. This feature lets the user start to gather samples of the
analog input from a known point, the rising edge of the SYNC
input. The SYNC input must be low for at least one master
clock cycle to ensure that synchronization occurs.
If multiple AD7175-2 devices are operated from a common
master clock, they can be synchronized so that their analog
inputs are sampled simultaneously. This synchronization is
normally done after each AD7175-2 device has performed its
own calibration or has calibration coefficients loaded into its
calibration registers. A falling edge on the SYNC input resets the
digital filter and the analog modulator and places the AD7175-2
into a consistent known state. While the SYNC input is low, the
AD7175-2 is maintained in this known state. On the SYNC
input rising edge, the modulator and filter are taken out of this
reset state, and on the next master clock edge, the device starts to
gather input samples again.
Rev. A | Page 44 of 60
Data Sheet
AD7175-2
The device is taken out of reset on the master clock falling edge
following the SYNC input low to high transition. Therefore,
when multiple devices are being synchronized, take the SYNC
input high on the master clock rising edge to ensure that all
devices are released on the master clock falling edge. If
the SYNC input is not taken high in sufficient time, a difference
of one master clock cycle between the devices is possible; that
is, the instant at which conversions are available differs from
device to device by a maximum of one master clock cycle.
The SYNC input can also be used as a start conversion
command for a single channel when in normal synchronization
mode. In this mode, the rising edge of SYNC input starts a
conversion, and the falling edge of the RDY output indicates
when the conversion is complete. The settling time of the filter is
required for each data register update. After the conversion is
complete, bring the SYNC input low in preparation for the next
conversion start signal.
Alternate Synchronization
In alternate synchronization mode, the SYNC input operates as
a start conversion command when several channels of the
AD7175-2 are enabled. Setting the ALT_SYNC bit in the interface
mode register to 1 enables an alternate synchronization scheme.
When the SYNC input is taken low, the ADC completes the
conversion on the current channel, selects the next channel in
the sequence, and then waits until the SYNC input is taken high
to commence the conversion. The RDY output goes low when
the conversion is complete on the current channel, and the data
register is updated with the corresponding conversion.
Therefore, the SYNC input does not interfere with the sampling
on the currently selected channel but allows the user to control
the instant at which the conversion begins on the next channel
in the sequence.
Alternate synchronization mode can be used only when several
channels are enabled. It is not recommended to use this mode
when a single channel is enabled.
ERROR FLAGS
The status register contains three error bits—ADC_ERROR,
CRC_ERROR, and REG_ERROR—that flag errors with the
ADC conversion, errors with the CRC check, and errors caused
by changes in the registers, respectively. In addition, the ERROR
output can indicate that an error has occurred.
ADC_ERROR
The ADC_ERROR bit in the status register flags any errors that
occur during the conversion process. The flag is set when an overrange or underrange result is output from the ADC. The ADC
also outputs all 0s or all 1s when an undervoltage or overvoltage
occurs. This flag is reset only when the overvoltage or undervoltage
is removed. It is not reset by a read of the data register.
CRC_ERROR
If the CRC value that accompanies a write operation does not
correspond with the information sent, the CRC_ERROR flag is
set. The flag is reset as soon as the status register is explicitly read.
REG_ERROR
The RE_ERROR flag is used in conjunction with the
REG_CHECK bit in the interface mode register. When the
REG_CHECK bit is set, the AD7175-2 monitors the values in
the on-chip registers. If a bit changes, the REG_ERROR bit is
set. Therefore, for writes to the on-chip registers, set
REG_CHECK to 0. When the registers have been updated, the
REG_CHECK bit can be set to 1. The AD7175-2 calculates a
checksum of the on-chip registers. If one of the register values
has changed, the REG_ERROR bit is set. If an error is flagged,
the REG_CHECK bit must be set to 0 to clear the REG_ERROR
bit in the status register. The register check function does not
monitor the data register, status register, or interface mode
register.
ERROR Input/Output
When the SYNC_EN bit in the GPIOCON register is set to 0,
the SYNC/ERROR pin functions as an error input/output pin or
a general-purpose output pin. The ERR_EN bits in the GPIOCON
register determine the function of the pin.
With ERR_EN is set to 10,the SYNC/ERROR pin functions as
an open-drain error output, ERROR. The three error bits in the
status register (ADC_ERROR, CRC_ERROR, and
REG_ERROR) are OR’ed, inverted, and mapped to the ERROR
output. Therefore, the ERROR output indicates that an error
has occurred. The status register must be read to identify the
error source.
When ERR_EN is set to 01, the SYNC/ERROR pin functions as
an error input, ERROR. The error output of another component
can be connected to the AD7175-2 ERROR input so that the
AD7175-2 indicates when an error occurs on either itself or the
external component. The value on the ERROR input is inverted
and OR’ed with the errors from the ADC conversion, and the
result is indicated via the ADC_ERROR bit in the status register.
The value of the ERROR input is reflected in the ERR_DAT bit
in the status register.
The ERROR input/output is disabled when ERR_EN is set to 00.
When the ERR_EN bits are set to 11, the SYNC/ERROR pin
operates as a general-purpose output.
DATA_STAT
The contents of the status register can be appended to each conversion on the AD7175-2. This function is useful if several
channels are enabled. Each time a conversion is output, the
contents of the status register are appended. The two LSBs of
the status register indicate to which channel the conversion
corresponds. In addition, the user can determine if any errors
are being flagged by the error bits.
Rev. A | Page 45 of 60
AD7175-2
Data Sheet
IOSTRENGTH
The serial interface can operate with a power supply as low as
2 V. However, at this low voltage, the DOUT/RDY pin may not
have sufficient drive strength if there is moderate parasitic
capacitance on the board or the SCLK frequency is high. The
IOSTRENGTH bit in the interface mode register increases the
drive strength of the DOUT/RDY pin.
INTERNAL TEMPERATURE SENSOR
The AD7175-2 has an integrated temperature sensor. The
temperature sensor can be used as a guide for the ambient
temperature at which the part is operating. This can be used for
diagnostic purposes or as an indicator of when the application
circuit needs to re-run a calibration routine to take into account
a shift in operating temperature. The temperature sensor is
selected using the crosspoint multiplexer and is selected the
same as an analog input channel. The temperature sensor
requires that the analog input buffers be enabled on both analog
inputs. If the buffers are not enabled then selecting the
temperature sensor as an input forces the buffers to be enabled
during the conversion.
To use the temperature sensor, the first step is to calibrate the
device in a known temperature (25°C) and take a conversion as
a reference point. The temperature sensor has a nominal
sensitivity of 477 µV/K; the difference in this ideal slope and the
slope measured can be used to calibrate the temperature sensor.
The temperature sensor is specified with a ±2°C typical
accuracy after calibration at 25°C. The temperature can be
calculated as follows:
Rev. A | Page 46 of 60
 Conversion Result
Temperature ( °C ) = 

477 μV


 – 273.15


Data Sheet
AD7175-2
GROUNDING AND LAYOUT
The analog inputs and reference inputs are differential and,
therefore, most of the voltages in the analog modulator are
common-mode voltages. The high common-mode rejection of
the device removes common-mode noise on these inputs. The
analog and digital supplies to the AD7175-2 are independent
and connected to separate pins to minimize coupling between the
analog and digital sections of the device. The digital filter
provides rejection of broadband noise on the power supplies,
except at integer multiples of the master clock frequency.
possible to provide low impedance paths and reduce glitches on
the power supply line. Shield fast switching signals like clocks
with digital ground to prevent radiating noise to other sections
of the board and never run clock signals near the analog inputs.
Avoid crossover of digital and analog signals. Run traces on
opposite sides of the board at right angles to each other. This
technique reduces the effects of feed through on the board. A
microstrip technique is by far the best but is not always possible
with a double-sided board.
The digital filter also removes noise from the analog and
reference inputs, provided that these noise sources do not
saturate the analog modulator. As a result, the AD7175-2 is
more immune to noise interference than a conventional high
resolution converter. However, because the resolution of the
AD7175-2 is high and the noise levels from the converter are so
low, take care with regard to grounding and layout.
Good decoupling is important when using high resolution ADCs.
The AD7175-2 has three power supply pins—AVDD1, AVDD2,
and IOVDD. The AVDD1 and AVDD2 pins are referenced to
AVSS, and the IOVDD pin is referenced to DGND. Decouple
AVDD1 and AVDD2 with a 10 µF capacitor in parallel with a
0.1 µF capacitor to AVSS on each pin. Place the 0.1 µF capacitor
as close as possible to the device on each supply, ideally right up
against the device. Decouple IOVDD with a 10 µF capacitor in
parallel with a 0.1 µF capacitor to DGND. Decouple all analog
inputs to AVSS. If an external reference is used, decouple the
REF+ and REF− pins to AVSS.
The PCB that houses the ADC must be designed such that the
analog and digital sections are separated and confined to
certain areas of the board. A minimum etch technique is
generally best for ground planes because it results in the best
shielding.
In any layout, the user must consider the flow of currents in the
system, ensuring that the paths for all return currents are as close as
possible to the paths the currents took to reach their destinations.
Avoid running digital lines under the device because this
couples noise onto the die and allow the analog ground plane to
run under the AD7175-2 to prevent noise coupling. The power
supply lines to the AD7175-2 must use as wide a trace as
The AD7175-2 also has two on-board LDO regulators—one
that regulates the AVDD2 supply and one that regulates the
IOVDD supply. For the REGCAPA pin, it is recommended that
1 µF and 0.1 µF capacitors to AVSS be used. Similarly, for the
REGCAPD pin, it is recommended that 1 µF and 0.1 µF
capacitors to DGND be used.
If using the AD7175-2 for split supply operation, a separate
plane must be used for AVSS.
Rev. A | Page 47 of 60
AD7175-2
Data Sheet
REGISTER SUMMARY
Table 24. Register Summary
Reg.
0x00
Name
COMMS
0x00
STATUS
0x01
ADCMODE
0x02
IFMODE
0x03
REGCHECK
0x04
DATA
0x06
GPIOCON
0x07
ID
0x10
CH0
0x11
CH1
0x12
CH2
0x13
CH3
0x20
SETUPCON0
0x21
SETUPCON1
0x22
SETUPCON2
0x23
SETUPCON3
0x28
FILTCON0
0x29
FILTCON1
0x2A
FILTCON2
0x2B
FILTCON3
0x30
0x31
0x32
0x33
0x38
0x39
0x3A
0x3B
OFFSET0
OFFSET1
OFFSET2
OFFSET3
GAIN0
GAIN1
GAIN2
GAIN3
Bits
[7:0]
Bit 7
WEN
Bit 6
R/W
Bit 5
Bit 4
[7:0]
RDY
[15:8]
[7:0]
[15:8]
[7:0]
[23:16]
[15:8]
[7:0]
[23:16]
[15:8]
[7:0]
[15:8]
[7:0]
[15:8]
[7:0]
[15:8]
[7:0]
[15:8]
[7:0]
[15:8]
[7:0]
[15:8]
[7:0]
[15:8]
[7:0]
[15:8]
[7:0]
[15:8]
[7:0]
[15:8]
[7:0]
[15:8]
[7:0]
[15:8]
[7:0]
[15:8]
[7:0]
[15:8]
[7:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
REF_EN
RESERVED
Bit 3
ADC_ERROR
CRC_ERROR
REG_ERROR
HIDE_DELAY
SING_CYC
MODE
RESERVED
Bit 2
RA
RESERVED
Bit 1
Bit 0
CHANNEL
RW
W
0x80
R
DELAY
0x8000
RESERVED
RESERVED
DOUT_RESET 0x0000
RESERVED
WL16
0x000000
CLOCKSEL
RESERVED
ALT_SYNC
IOSTRENGTH
CONTREAD
DATA_STAT
REG_CHECK RESERVED
CRC_EN
REGISTER_CHECK[23:16]
REGISTER_CHECK[15:8]
REGISTER_CHECK[7:0]
DATA[23:16]
DATA[15:8]
DATA[7:0]
RESERVED
MUX_IO
SYNC_EN
ERR_EN
ERR_DAT
RESERVED
IP_EN1
IP_EN0
OP_EN1
OP_EN0
GP_DATA1
GP_DATA0
ID[15:8]
ID[7:0]
CH_EN0
RESERVED
SETUP_SEL0
RESERVED
AINPOS0[4:3]
AINPOS0[2:0]
AINNEG0
CH_EN1
RESERVED
SETUP_SEL1
RESERVED
AINPOS1[4:3]
AINPOS1[2:0]
AINNEG1
CH_EN2
RESERVED
SETUP_SEL2
RESERVED
AINPOS2[4:3]
AINPOS2[2:0]
AINNEG2
CH_EN3
RESERVED
SETUP_SEL3
RESERVED
AINPOS3[4:3]
AINPOS3[2:0]
AINNEG3
RESERVED
BI_UNIPOLAR0
REFBUF0+
REFBUF0AINBUF0+
AINBUF0−
BURNOUT_EN0
RESERVED
REF_SEL0
RESERVED
RESERVED
BI_UNIPOLAR1
REFBUF1+
REFBUF1−
AINBUF1+
AINBUF1−
BURNOUT_EN1
RESERVED
REF_SEL1
RESERVED
RESERVED
BI_UNIPOLAR2
REFBUF2+
REFBUF2−
AINBUF2+
AINBUF2−
BURNOUT_EN2
RESERVED
REF_SEL2
RESERVED
RESERVED
BI_UNIPOLAR3
REFBUF3+
REFBUF3−
AINBUF3+
AINBUF3−
BURNOUT_EN3
RESERVED
REF_SEL3
RESERVED
SINC3_MAP0
RESERVED
ENHFILTEN0
ENHFILT0
RESERVED
ORDER0
ODR0
SINC3_MAP1
RESERVED
ENHFILTEN1
ENHFILT1
RESERVED
ORDER1
ODR1
SINC3_MAP2
RESERVED
ENHFILTEN2
ENHFILT2
RESERVED
ORDER2
ODR2
SINC3_MAP3
RESERVED
ENHFILTEN3
ENHFILT3
RESERVED
ORDER3
ODR3
OFFSET0[23:0]
OFFSET1[23:0]
OFFSET2[23:0]
OFFSET3[23:0]
GAIN0[23:0]
GAIN1[23:0]
GAIN2[23:0]
GAIN3[23:0]
Rev. A | Page 48 of 60
Reset
0x00
RW
RW
R
0x000000
R
0x0800
RW
0x0CDX
R
0x8001
RW
0x0001
RW
0x0001
RW
0x0001
RW
0x1320
RW
0x1320
RW
0x1320
RW
0x1320
RW
0x0500
RW
0x0500
RW
0x0500
RW
0x0500
RW
0x800000
0x800000
0x800000
0x800000
0x5XXXX0
0x5XXXX0
0x5XXXX0
0x5XXXX0
RW
RW
RW
RW
RW
RW
RW
RW
Data Sheet
AD7175-2
REGISTER DETAILS
COMMUNICATIONS REGISTER
Address: 0x00, Reset: 0x00, Name: COMMS
All access to the on-chip registers must start with a write to the communications register. This write determines what register is next
accessed and whether that operation is a write or a read.
Table 25. Bit Descriptions for COMMS
Bits
7
Bit Name
WEN
6
R/W
Settings
0
1
[5:0]
RA
000000
000001
000010
000011
000100
000110
000111
010000
010001
010010
010011
100000
100001
100010
100011
101000
101001
101010
101011
110000
110001
110010
110011
111000
111001
111010
111011
Description
This bit must be low to begin communications with the ADC.
Reset
0x0
Access
W
This bit determines if the command is a read or write operation.
Write command
Read command
The register address bits determine which register is to be read from or
written to as part of the current communication.
Status register
ADC mode register
Interface mode register
Register checksum register
Data register
GPIO configuration register
ID register
Channel 0 register
Channel 1 register
Channel 2 register
Channel 3 register
Setup Configuration 0 register
Setup Configuration 1 register
Setup Configuration 2 register
Setup Configuration 3 register
Filter Configuration 0 register
Filter Configuration 1 register
Filter Configuration 2 register
Filter Configuration 3 register
Offset 0 register
Offset 1 register
Offset 2 register
Offset 3 register
Gain 0 register
Gain 1 register
Gain 2 register
Gain 3 register
0x0
W
0x00
W
Rev. A | Page 49 of 60
AD7175-2
Data Sheet
STATUS REGISTER
Address: 0x00, Reset: 0x80, Name: STATUS
The status register is an 8-bit register that contains ADC and serial interface status information. It can optionally be appended to the data
register by setting the DATA_STAT bit in the interface mode register.
Table 26. Bit Descriptions for STATUS
Bits
7
Bit Name
RDY
Settings
0
1
6
ADC_ERROR
0
1
5
CRC_ERROR
0
1
4
REG_ERROR
0
1
[3:2]
[1:0]
RESERVED
CHANNEL
00
01
10
11
Description
The status of RDY is output to the DOUT/RDYpin whenever CS is low and a
register is not being read. This bit goes low when the ADC has written a
new result to the data register. In ADC calibration modes, this bit goes low
when the ADC has written the calibration result. RDY is brought high
automatically by a read of the data register.
New data result available
Awaiting new data result
This bit by default indicates if an ADC overrange or underrange has
occurred. The ADC result is clamped to 0xFFFFFF for overrange errors and
0x000000 for underrange errors. This bit is updated when the ADC result is
written and is cleared at the next update after removing the overrange or
underrange condition.
No error
Error
This bit indicates if a CRC error has taken place during a register write. For
register reads, the host microcontroller determines if a CRC error has
occurred. This bit is cleared by a read of this register.
No error
CRC error
This bit indicates if the content of one of the internal registers has
changed from the value calculated when the register integrity check was
activated. The check is activated by setting the REG_CHECK bit in the
interface mode register. This bit is cleared by clearing the REG_CHECK bit.
No error
Error
These bits are reserved.
These bits indicate which channel was active for the ADC conversion
whose result is currently in the data register. This may be different from
the channel currently being converted. The mapping is a direct map from
the channel register; therefore, Channel 0 results in 0x0 and Channel 3
results in 0x3.
Channel 0
Channel 1
Channel 2
Channel 3
Rev. A | Page 50 of 60
Reset
0x1
Access
R
0x0
R
0x0
R
0x0
R
0x0
0x0
R
R
Data Sheet
AD7175-2
ADC MODE REGISTER
Address: 0x01, Reset: 0x8000, Name: ADCMODE
The ADC mode register controls the operating mode of the ADC and the master clock selection. A write to the ADC mode register resets
the filter and the RDY bits and starts a new conversion or calibration.
Table 27. Bit Descriptions for ADCMODE
Bits
15
Bit Name
REF_EN
Settings
0
1
14
HIDE_DELAY
0
1
13
SING_CYC
0
1
[12:11]
[10:8]
RESERVED
DELAY
000
001
010
011
100
101
110
111
7
[6:4]
RESERVED
MODE
000
001
010
011
100
110
111
[3:2]
CLOCKSEL
00
01
10
11
[1:0]
RESERVED
Description
Enables internal reference and outputs a buffered 2.5 V to the REFOUT pin.
Disabled
Enabled
If a programmable delay has been set using the DELAY bits, this bit allows
the delay to be hidden by absorbing the delay into the conversion time
for selected data rates with the sinc5 + sinc1 filter. See the Delay section
for more information.
Enabled
Disabled
This bit can be used when only a single channel is active to set the ADC to
only output at the settled filter data rate.
Disabled
Enabled
These bits are reserved; set these bits to 0.
These bits allow a programmable delay to be added after a channel switch
to allow settling of external circuitry before the ADC starts processing its
input.
0 µs
4 µs
16 µs
40 µs
100 µs
200 µs
500 µs
1 ms
This bit is reserved; set this bit to 0.
These bits control the operating mode of the ADC. See the Operating
Modes section for more information.
Continuous conversion mode
Single conversion mode
Standby mode
Power-down mode
Internal offset calibration
System offset calibration
System gain calibration
This bit is used to select the ADC clock source. Selecting internal oscillator
also enables the internal oscillator.
Internal oscillator
Internal oscillator output on XTAL2/CLKIO pin
External clock input on XTAL2/CLKIO pin
External crystal on XTAL1 and XTAL2/CLKIO pins
These bits are reserved; set these bits to 0.
Rev. A | Page 51 of 60
Reset
0x1
Access
RW
0x0
RW
0x0
RW
0x0
0x0
R
RW
0x0
0x0
R
RW
0x0
RW
0x0
R
AD7175-2
Data Sheet
INTERFACE MODE REGISTER
Address: 0x02, Reset: 0x0000, Name: IFMODE
The interface mode register configures various serial interface options.
Table 28. Bit Descriptions for IFMODE
Bits
[15:13]
12
Bit Name
RESERVED
ALT_SYNC
Settings
0
1
11
IOSTRENGTH
0
1
[10:9]
8
RESERVED
DOUT_RESET
0
1
7
CONTREAD
0
1
6
DATA_STAT
0
1
5
REG_CHECK
0
1
4
[3:2]
RESERVED
CRC_EN
00
01
10
1
RESERVED
Description
These bits are reserved; set these bits to 0.
This bit enables a different behavior of the SYNC/ERROR pin to allow the
use of SYNC/ERROR as a control for conversions when cycling channels
(see the description of the SYNC_EN bit in the GPIO Configuration Register
section for details).
Disabled
Enabled
This bit controls the drive strength of the DOUT/RDY pin. Set this bit
when reading from the serial interface at high speed with a low IOVDD
supply and moderate capacitance.
Disabled (default)
Enabled
These bits are reserved; set these bits to 0.
See DOUT_RESET section for more information.
Disabled
Enabled
This enables continuous read of the ADC data register. The ADC must be
configured in continuous conversion mode to use continuous read. For
more details, see the Operating Modes section.
Disabled
Enabled
This enables the status register to be appended to the data register when
read so that channel and status information are transmitted with the data.
This is the only way to be sure that the channel bits read from the status
register correspond to the data in the data register.
Disabled
Enabled
This bit enables a register integrity checker, which can be used to monitor
any change in the value of the user registers. To use this feature, configure
all other registers as desired, with this bit cleared. Then write to this register to
set the REG_CHECK bit to 1. If the contents of any of the registers change,
the REG_ERROR bit is set in the status register. To clear the error, set the
REG_CHECK bit to 0. Neither the interface mode register nor the ADC data
or status registers are included in the registers that are checked. If a
register must have a new value written, this bit must first be cleared;
otherwise, an error is flagged when the new register contents are written.
Disabled
Enabled
This bit is reserved; set this bit to 0.
Enables CRC protection of register reads/writes. CRC increases the
number of bytes in a serial interface transfer by one. See the CRC
Calculation section for more details.
Disabled
XOR checksum enabled for register read transactions; register writes still
use CRC with these bits set
CRC checksum enabled for read and write transactions
This bit is reserved; set this bit to 0.
Rev. A | Page 52 of 60
Reset
0x0
0x0
Access
R
RW
0x0
RW
0x0
0x0
R
RW
0x0
RW
0x0
RW
0x0
RW
0x0
0x00
R
RW
0x0
R
Data Sheet
Bits
0
Bit Name
WL16
AD7175-2
Settings
0
1
Description
Changes the ADC data register to 16 bits. The ADC is not reset by a write
to the interface mode register; therefore, the ADC result is not rounded to
the correct word length immediately after writing to these bits. The first
new ADC result is correct.
24-bit data
16-bit data
Reset
0x0
Access
RW
REGISTER CHECK
Address: 0x03, Reset: 0x000000, Name: REGCHECK
The register check register is a 24-bit checksum calculated by exclusively OR'ing the contents of the user registers. The REG_CHECK bit
in the interface mode register must be set for this to operate; otherwise, the register reads 0.
Table 29. Bit Descriptions for REGCHECK
Bits
[23:0]
Bit Name
REGISTER_CHECK
Settings
Description
This register contains the 24-bit checksum of user registers when the
REG_CHECK bit is set in the interface mode register.
Reset
0x000000
Access
R
DATA REGISTER
Address: 0x04, Reset: 0x000000, Name: DATA
The data register contains the ADC conversion result. The encoding is offset binary, or it can be changed to unipolar by the
BI_UNIPOLARx bit in the setup configuration registers. Reading the data register brings the RDY bit and the RDY output high if it had
been low. The ADC result can be read multiple times; however, because the RDY output has been brought high, it is not possible to know
if another ADC result is imminent. After the command to read the ADC register is received, the ADC does not write a new result into the
data register.
Table 30. Bit Descriptions for DATA
Bits
[23:0]
Bit Name
DATA
Settings
Description
This register contains the ADC conversion result. If DATA_STAT is set in
the interface mode register, the status register is appended to this
register when read, making this a 32-bit register. If WL16 is set in the
interface mode register, this register is reduced to 16 bits.
Rev. A | Page 53 of 60
Reset
0x000000
Access
R
AD7175-2
Data Sheet
GPIO CONFIGURATION REGISTER
Address: 0x06, Reset: 0x0800, Name: GPIOCON
The GPIO configuration register controls the general-purpose I/O pins of the ADC.
Table 31. Bit Descriptions for GPIOCON
Bits
[15:13]
12
Bit Name
RESERVED
MUX_IO
11
SYNC_EN
Settings
0
1
[10:9]
ERR_EN
00
01
10
11
8
ERR_DAT
[7:6]
5
RESERVED
IP_EN1
0
1
4
IP_EN0
0
1
3
OP_EN1
0
1
2
OP_EN0
0
1
1
0
GP_DATA1
GP_DATA0
Description
These bits are reserved; set these bits to 0.
This bit allows the ADC to control an external multiplexer, using GPIO0/GPIO1 in sync
with the internal channel sequencing. The analog input pins used for a channel
can still be selected on a per channel basis. Therefore, it is possible to have a
4-channel multiplexer in front of AIN0/AIN1 and another in front of AIN2/AIN3, giving a
total of eight differential channels with the AD7175-2. However, only four channels at a
time can be automatically sequenced. A delay can be inserted after switching an
external multiplexer (see the DELAY bits in the ADC Mode Register section).
This bit enables the SYNC/ERROR pin as a sync input. When the pin is low, this
holds the ADC and filter in reset until SYNC/ERROR pin goes high. An alternative
operation of the SYNC/ERROR pin is available when the ALT_SYNC bit in the
interface mode register is set. This mode only works when multiple channels are
enabled. In this case, a low on the SYNC/ERROR pin does not immediately reset the
filter/modulator. Instead, if the SYNC/ERROR pin is low when the channel is due to
be switched, the modulator and filter are prevented from starting a new
conversion. Bringing SYNC/ERROR high begins the next conversion. This
alternative sync mode allows SYNC/ERROR to be used while cycling through channels.
Disabled.
Enabled.
These bits enable the SYNC/ERROR pin as an error input/output.
Disabled.
SYNC/ERROR is an error input. The (inverted) readback state is OR'ed with other
error sources and is available in the ADC_ERROR bit in the status register. The SYNC
/ ERROR pin state can also be read from the ERR_DAT bit in this register.
SYNC/ERROR is an open-drain error output. The status register error bits are OR'ed,
inverted, and mapped to the SYNC/ERROR pin. The SYNC/ERROR pins of multiple
devices can be wired together to a common pull-up resistor so that an error on
any device can be observed.
SYNC/ERROR is a general-purpose output. The status of the pin is controlled by the
ERR_DAT bit in this register. This output is referenced between IOVDD and DGND,
as opposed to the AVDD1 and AVSS levels used by the general-purpose I/O pins.
The SYNC/ERROR pin has an active pull-up in this case.
Reset
0x0
0x0
Access
R
RW
0x1
RW
0x0
RW
This bit determines the logic level at the SYNC/ERROR pin if the pin is enabled as a
general-purpose output. This bit reflects the readback status of the pin if the pin is
enabled as an input.
These bits are reserved; set these bits to 0.
This bit turns GPIO1 into an input. Inputs are referenced to AVDD1 or AVSS.
Disabled.
Enabled.
This bit turns GPIO0 into an input. Inputs are referenced to AVDD1 or AVSS.
Disabled.
Enabled.
This bit turns GPIO1 into an output. Outputs are referenced between AVDD1 and AVSS.
Disabled.
Enabled.
This bit turns GPIO0 into an output. Outputs are referenced between AVDD1 and AVSS.
Disabled.
Enabled.
This bit is the readback or write data for GPIO1.
This bit is the readback or write data for GPIO0.
0x0
RW
0x0
0x0
R
RW
0x0
RW
0x0
RW
0x0
RW
0x0
0x0
RW
RW
Rev. A | Page 54 of 60
Data Sheet
AD7175-2
ID REGISTER
Address: 0x07, Reset: 0x0CDX, Name: ID
The ID register returns a 16-bit ID. For the AD7175-2, this should be 0x0CDX.
Table 32. Bit Descriptions for ID
Bits
[15:0]
Bit Name
ID
Settings
0x0CDX
Description
The ID register returns a 16-bit ID code that is specific to the ADC.
AD7175-2
Reset
0x0CDX
Access
R
CHANNEL REGISTER 0
Address: 0x10, Reset: 0x8001, Name: CH0
The channel registers are 16-bit registers that are used to select which channels are currently active, which inputs are selected for each
channel, and which setup is used to configure the ADC for that channel.
Table 33. Bit Descriptions for CH0
Bits
15
Bit Name
CH_EN0
Settings
0
1
14
[13:12]
RESERVED
SETUP_SEL0
00
01
10
11
[11:10]
[9:5]
RESERVED
AINPOS0
00000
00001
00010
00011
00100
10001
10010
10011
10100
10101
10110
Description
This bit enables Channel 0. If more than one channel is enabled, the ADC
automatically sequences between them.
Disabled
Enabled (default)
This bit is reserved; set this bit to 0.
These bits identify which of the four setups are used to configure the ADC
for this channel. A setup comprises a set of four registers: setup configuration
register, filter configuration register, offset register, and gain register. All
channels can use the same setup, in which case the same 2-bit value must be
written to these bits on all active channels, or up to four channels can be
configured differently.
Setup 0
Setup 1
Setup 2
Setup 3
These bits are reserved; set these bits to 0.
These bits select which input is connected to the positive input of the
ADC for this channel.
AIN0 (default)
AIN1
AIN2
AIN3
AIN4
Temperature sensor+
Temperature sensor−
((AVDD1 − AVSS)/5)+ (analog input buffers must be enabled)
((AVDD1 − AVSS)/5)− (analog input buffers must be enabled)
REF+
REF−
Rev. A | Page 55 of 60
Reset
0x1
Access
RW
0x0
0x0
R
RW
0x0
0x0
R
RW
AD7175-2
Bits
[4:0]
Data Sheet
Bit Name
AINNEG0
Settings
00000
00001
00010
00011
00100
10001
10010
10011
10100
10101
10110
Description
These bits select which input is connected to the negative input of the
ADC for this channel.
AIN0
AIN1 (default)
AIN2
AIN3
AIN4
Temperature sensor+
Temperature sensor−
((AVDD1 − AVSS)/5)+
((AVDD1 − AVSS)/5)−
REF+
REF−
Reset
0x1
Access
RW
CHANNEL REGISTER 1 TO CHANNEL REGISTER 3
Address: 0x11 to 0x13, Reset: 0x0001, Name: CH1 to CH3
The remaining three channel registers share the same layout as Channel Register 0.
Table 34. CH1 to CH3 Register Map
Reg.
0x11
Name
CH1
Bits
[15:8]
[7:0]
Bit 7
CH_EN1
Bit 6
RESERVED
AINPOS1[2:0]
0x12
CH2
[15:8]
[7:0]
CH_EN2
RESERVED
AINPOS2[2:0]
0x13
CH3
[15:8]
CH_EN3
[7:0]
RESERVED
Bit 5
Bit 4
SETUP_SEL1
Bit 3
Bit 2
RESERVED
AINNEG1
Bit 1
Bit 0
AINPOS1[4:3]
Reset
0x0001
RW
RW
SETUP_SEL2
RESERVED
AINNEG2
AINPOS2[4:3]
0x0001
RW
SETUP_SEL3
RESERVED
AINPOS3[4:3]
0x0001
RW
AINPOS3[2:0]
AINNEG3
Rev. A | Page 56 of 60
Data Sheet
AD7175-2
SETUP CONFIGURATION REGISTER 0
Address: 0x20, Reset: 0x1320, Name: SETUPCON0
The setup configuration registers are 16-bit registers that configure the reference selection, input buffers, and output coding of the ADC.
Table 35. Bit Descriptions for SETUPCON0
Bits
[15:13]
12
Bit Name
RESERVED
BI_UNIPOLAR0
Settings
0
1
11
REFBUF0+
0
1
10
REFBUF0−
0
1
9
AINBUF0+
0
1
8
AINBUF0−
0
1
7
BURNOUT_EN0
6
[5:4]
RESERVED
REF_SEL0
00
10
11
[3:0]
RESERVED
Description
These bits are reserved; set these bits to 0.
This bit sets the output coding of the ADC for Setup 0.
Unipolar coded output
Bipolar coded output (offset binary)
This bit enables or disables the REF+ input buffer.
REF+ buffer disabled
REF+ buffer enabled
This bit enables or disables the REF− input buffer.
REF− buffer disabled
REF− buffer enabled
This bit enables or disables the AIN+ input buffer.
AIN+ buffer disabled
AIN+ buffer enabled
This bit enables or disables the AIN− input buffer.
AIN− buffer disabled
AIN− buffer enabled
This bit enables a 10 µA current source on the positive analog input
selected and a 10 µA current sink on the negative analog input selected.
The burnout currents are useful in diagnosis of an open wire, whereby the
ADC result goes to full scale. Enabling the burnout currents during
measurement results in an offset voltage on the ADC. This means the
strategy for diagnosing an open wire operates best by turning on the
burnout currents at intervals, before or after precision measurements.
These bits are reserved; set these bits to 0.
These bits allow you to select the reference source for ADC conversion on
Setup 0.
External Reference.
Internal 2.5 V Reference. This must also be enabled in the ADC mode register.
AVDD1 − AVSS. This can be used to as a diagnostic to validate other
reference values.
These bits are reserved; set these bits to 0.
Reset
0x0
0x1
Access
R
RW
0x0
RW
0x0
RW
0x1
RW
0x1
RW
0x00
R
0x00
0x2
R
RW
0x0
R
SETUP CONFIGURATION REGISTER 1 TO SETUP CONFIGURATION REGISTER 3
Address: 0x21 to 0x23, Reset: 0x1320, Name: SETUPCON1 to SETUPCON3
The remaining three setup configuration registers share the same layout as Setup Configuration Register 0.
Table 36. SETUPCON1 to SETUPCON3 Register Map
Reg.
0x21
Name
SETUPCON1
0x22
SETUPCON2
0x23
SETUPCON3
Bits
[15:8]
[7:0]
[15:8]
[7:0]
[15:8]
[7:0]
Bit 7
BURNOUT_EN1
BURNOUT_EN2
BURNOUT_EN3
Bit 6
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
Bit 5
Bit 4
BI_UNIPOLAR1
REF_SEL1
BI_UNIPOLAR2
REF_SEL2
BI_UNIPOLAR3
REF_SEL3
Rev. A | Page 57 of 60
Bit 3
REFBUF1+
REFBUF2+
REFBUF3+
Bit 2
Bit 1
REFBUF1−
AINBUF1+
RESERVED
REFBUF2−
AINBUF2+
RESERVED
REFBUF3−
AINBUF3+
RESERVED
Bit 0
AINBUF1−
Reset
0x1320
RW
RW
AINBUF2−
0x1320
RW
AINBUF3−
0x1320
RW
AD7175-2
Data Sheet
FILTER CONFIGURATION REGISTER 0
Address: 0x28, Reset: 0x0500, Name: FILTCON0
The filter configuration registers are 16-bit registers that configure the ADC data rate and filter options. Writing to any of these registers
resets any active ADC conversion and restarts converting at the first channel in the sequence.
Table 37. Bit Descriptions for FILTCON0
Bits
15
Bit Name
SINC3_MAP0
[14:12]
11
RESERVED
ENHFILTEN0
Settings
0
1
[10:8]
ENHFILT0
010
011
101
110
7
[6:5]
RESERVED
ORDER0
00
11
[4:0]
ODR0
00000
00001
00010
00011
00100
00101
00110
00111
01000
01001
01010
01011
01100
01101
01110
01111
10000
10001
10010
10011
10100
Description
If this bit is set, the mapping of the filter register changes to directly
program the decimation rate of the sinc3 filter for Setup 0. All other
options are eliminated. This allows fine tuning of the output data rate and
filter notch for rejection of specific frequencies. The data rate when on a
single channel equals fMOD/(32 × FILTCON0[14:0]).
These bits are reserved; set these bits to 0.
This bit enables various postfilters for enhanced 50 Hz/60 Hz rejection for
Setup 0. The ORDER0 bits must be set to 00 to select the sinc5 + sinc1
filter for this to work.
Disabled
Enabled
These bits select between various postfilters for enhanced 50 Hz/60 Hz
rejection for Setup 0.
27 SPS, 47 dB rejection, 36.7 ms settling
25 SPS, 62 dB rejection, 40 ms settling
20 SPS, 86 dB rejection, 50 ms settling
16.67 SPS, 92 dB rejection, 60 ms settling
This bit is reserved; set this bit to 0.
These bits control the order of the digital filter that processes the
modulator data for Setup 0.
Sinc5 + sinc1 (default)
Sinc3
These bits control the output data rate of the ADC and, therefore, the
settling time and noise for Setup 0. Rates shown as for sinc5 + sinc 1 filter.
See Table 19 to Table 22.
250,000
125,000
62,500
50,000
31,250
25,000
15,625
10,000
5000
2500
1000
500
397.5
200
100
59.92
49.96
20
16.66
10
5
Rev. A | Page 58 of 60
Reset
0x0
Access
RW
0x0
0x0
R
RW
0x5
RW
0x0
0x0
R
RW
0x0
RW
Data Sheet
AD7175-2
FILTER CONFIGURATION REGISTER 1 TO FILTER CONFIGURATION REGISTER 3
Address: 0x29 to 0x2B, Reset: 0x0500, Name: FILTCON1 to FILTCON3
The remaining three filter configuration registers share the same layout as Filter Configuration Register 0.
Table 38. FILTCON1 to FILTCON3 Register Map
Reg.
Name
Bits
Bit 7
0x29
FILTCON1
[15:8]
[7:0]
SINC3_MAP1
RESERVED
RESERVED
ORDER1
ENHFILTEN1
[15:8]
[7:0]
SINC3_MAP2
RESERVED
RESERVED
ORDER2
ENHFILTEN2
[15:8]
SINC3_MAP3
RESERVED
ENHFILTEN3
[7:0]
RESERVED
0x2A
0x2B
FILTCON2
FILTCON3
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Reset
RW
ENHFILT1
Bit 0
0x0500
RW
ENHFILT2
0x0500
RW
ENHFILT3
0x0500
RW
ODR1
ODR2
ORDER3
ODR3
OFFSET REGISTER 0
Address: 0x30, Reset: 0x800000, Name: OFFSET0
The offset (zero-scale) registers are 24-bit registers that can be used to compensate for any offset error in the ADC or in the system.
Table 39. Bit Descriptions for OFFSET0
Bits
[23:0]
Bit Name
OFFSET0
Settings
Description
Offset calibration coefficient for Setup 0.
Reset
0x800000
Access
RW
OFFSET REGISTER 1 TO OFFSET REGISTER 3
Address: 0x31 to 0x33, Reset: 0x800000, Name: OFFSET1 to OFFSET3
The remaining three offset registers share the same layout as Offset Register 0.
Table 40. OFFSET1 to OFFSET3 Register Map
Reg.
0x31
0x32
0x33
Name
OFFSET1
OFFSET2
OFFSET3
Bits
[23:0]
[23:0]
[23:0]
OFFSET1[23:0]
OFFSET2[23:0]
OFFSET3[23:0]
Reset
0x800000
0x800000
0x800000
RW
RW
RW
RW
GAIN REGISTER 0
Address: 0x38, Reset: 0x5XXXX0, Name: GAIN0
The gain (full-scale) registers are 24-bit registers that can be used to compensate for any gain error in the ADC or in the system.
Table 41. Bit Descriptions for GAIN0
Bits
[23:0]
Bit Name
GAIN0
Settings
Description
Gain calibration coefficient for Setup 0.
Reset
0x5XXXX0
Access
RW
GAIN REGISTER 1 TO GAIN REGISTER 3
Address: 0x39 to 0x3B, Reset: 0x5XXXX0, Name: GAIN1 to GAIN3
The remaining three gain registers share the same layout as Gain Register 0.
Table 42. GAIN1 to GAIN3 Register Map
Reg.
0x39
0x3A
0x3B
Name
GAIN1
GAIN2
GAIN3
Bits
[23:0]
[23:0]
[23:0]
GAIN1[23:0]
GAIN2[23:0]
GAIN3[23:0]
Rev. A | Page 59 of 60
Reset
0x5XXXX0
0x5XXXX0
0x5XXXX0
RW
RW
RW
RW
AD7175-2
Data Sheet
OUTLINE DIMENSIONS
7.90
7.80
7.70
24
13
4.50
4.40
4.30
6.40 BSC
1
12
PIN 1
0.65
BSC
0.15
0.05
0.30
0.19
1.20
MAX
SEATING
PLANE
0.20
0.09
8°
0°
0.75
0.60
0.45
0.10 COPLANARITY
COMPLIANT TO JEDEC STANDARDS MO-153-AD
Figure 75. 24-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-24)
Dimensions shown in millimeters
ORDERING GUIDE
Models1
AD7175-2BRUZ
AD7175-2BRUZ-RL
AD7175-2BRUZ-RL7
EVAL-AD7175-2SDZ
EVAL-SDP-CB1Z
1
Temperature Range
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
Package Description
24-Lead Thin Shrink Small Outline Package [TSSOP]
24-Lead Thin Shrink Small Outline Package [TSSOP]
24-Lead Thin Shrink Small Outline Package [TSSOP]
Evaluation Board
Evaluation Controller Board
Z = RoHS Compliant Part.
©2014 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D12468-0-9/14(A)
Rev. A | Page 60 of 60
Package Option
RU-24
RU-24
RU-24