Application Report SNAA039A – July 2007 – Revised May 2013 AN-1591 LM49370 PCM/I2S Bridge ..................................................................................................................................................... ABSTRACT This application report describes the LM49370 PCM/I2S Bridge. 1 2 3 4 5 6 7 8 9 Contents PCM/I2S Bridge Overview .................................................................................................. 3 PCM/I2S Bridge Explained ................................................................................................. 3 PCM and I2S Running at the Same Sample Rate ...................................................................... 5 I2S and PCM Running at Different Sample Rates Within the Same Sample Rate Family ........................ 6 PCM and I2S Running at Sample Rates from Different Sample Rate Families ................................... 13 Setting the Correct Clocks ............................................................................................... 15 Two-Way Voice Communication or Music Playback via Bluetooth Headset Without Using the PCM/I2S Bridge ....................................................................................................................... 17 Stereo Bluetooth Headsets ............................................................................................... 18 Revision History ........................................................................................................... 18 List of Figures 1 System Level Diagram ..................................................................................................... 3 2 System Level Diagram with LM49370 PCM-I2S Bridge ................................................................ 3 3 Overall PCM/I2S Bridge Diagram 4 PCM and I2S Running at the Same Sample Rate (Voice Communication, Voice Record, or MP3/MP4 Playback) ..................................................................................................................... 5 5 PCM and I2S Running at Different Sample Rates Within the Same Sample Rate Family (Voice Record) 6 PCM and I2S Running at Different Sample Rates Within the Same Sample Rate Family (MP3/MP4 Playback) ..................................................................................................................... 7 7 PCM and I2S Running at Different Sample Rates from Different Sample Rate Families (Voice Record) ......................................................................................... ..... ..... 4 6 14 2 8 PCM and I S Running at Different Sample Rates from Different Sample Rate Families (MP3/MP4 Playback) ................................................................................................................... 14 9 LM49370 Clock Network 10 11 ................................................................................................. Audio Port CLOCK/SYNC Options ...................................................................................... PCM Audio Port CLOCK/SYNC Options ............................................................................... 15 16 16 12 Using the LM49370 with a Dedicated RF Module for Two-way Voice Communication via Bluetooth Headset .................................................................................................................... 17 13 Alternative Method for Two-way Voice Communication via Bluetooth 14 Using the LM49370 to Route FM Radio or TV Audio to a Bluetooth Headset 15 ............................................ ................................... FM Radio or TV Tuner Playback via Bluetooth Headset ............................................................. 17 18 18 List of Tables .................................... .................................. Converting 16kHz to Other Sample Rates Within the Same Family (OSR = 128) ................................. Converting 24kHz to Other Sample Rates Within the Same Family (OSR = 128) ............................... Converting 32kHz to Other Sample Rates Within the Same Family (OSR = 128) ............................... 2 2 1 PCM/I S Bridge Settings (I S and PCM Operating at the Same Sample Rate) 5 2 Converting 8kHz to Other Sample Rates Within the Same Family (OSR = 128) 8 3 4 5 9 10 11 All trademarks are the property of their respective owners. AN-1591 LM49370 PCM/I2S Bridge SNAA039A – July 2007 – Revised May 2013 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated 1 www.ti.com 2 ............................... 6 Converting 48kHz to Other Sample Rates Within the Same Family (OSR = 128) 7 Converting any 48kHz Related Sample Rate to Other Sample Rates Within the Same Family (OSR = 125).......................................................................................................................... 12 8 Converting a Sample Rate to Another Sample Rate from a Different Sample Rate Family AN-1591 LM49370 PCM/I2S Bridge .................... 12 13 SNAA039A – July 2007 – Revised May 2013 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated PCM/I2S Bridge Overview www.ti.com 1 PCM/I2S Bridge Overview With an ever increasing feature set found in today’s mobile phones, reducing software overhead and baseband processor loading is high priority for any mobile phone design. The most straightforward way to accomplish this without sacrificing any features is to delegate some of the baseband processor’s duties over to an external IC. One such duty is the management of multiple digital audio formats such as mono PCM (for voice) and stereo I2S (for music). Bluetooth headset support and MP3/MP4 playback capability are standard features that facilitate the need to manage different digital audio interfaces within the same system. As shown in Figure 1, a Bluetooth transceiver typically uses a mono PCM audio format during a voice communication whereas an external audio DAC uses a stereo I2S audio format for MP3/MP4 playback. Baseband Processor Audio Port 1 Audio Port 2 2 PCM (mono) 802.15.1 I S (Stereo) Stereo DAC with Loudspeaker and Headphone Amplifiers Bluetooth Transceiver Bluetooth Headset Figure 1. System Level Diagram The onboard PCM/I2S bridge of the LM49370 allows the baseband processor to manage just a single digital audio interface thereby reducing processor load and associating software overhead. The LM49370 links directly to the Bluetooth transceiver, freeing up a valuable audio port on the baseband microprocessor. The PCM/I2S bridge can convert a mono PCM interface into a stereo I2S interface or conversely. Baseband Processor Audio Port 1 2 I S (Stereo) 802.15.1 2 Bluetooth Transceiver PCM-I S Bridge LM49370 PCM (mono) Bluetooth Headset Figure 2. System Level Diagram with LM49370 PCM-I2S Bridge 2 PCM/I2S Bridge Explained The PCM/I2S bridge is specifically targeted for mobile phone applications that require the use of a mono Bluetooth headset. A mono Bluetooth headset is used for voice record, music playback, and two-way voice communication. In the voice record scenario, the PCM/I2S bridge accepts voice data in mono PCM format at a particular sample rate from a Bluetooth transceiver. The incoming PCM audio data is then converted to a stereo I2S format at a programmable sample rate that is sent out through the LM49370’s I2S output port over to the baseband processor for recording. In the music playback scenario, the PCM/I2S bridge accepts music data in stereo I2S format at a particular sample rate from the baseband processor. The left and right I2S data can then be summed together and converted to a mono PCM format. The converted mono PCM music data is then routed to the Bluetooth transceiver at a programmable sample rate via the LM49370’s PCM output port. AN-1591 LM49370 PCM/I2S Bridge SNAA039A – July 2007 – Revised May 2013 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated 3 PCM/I2S Bridge Explained www.ti.com For two-way voice communication, it is assumed that the I2S port on the baseband processor handles the voice receive and transmit for this particular example. Also, the I2S and PCM interfaces must run at the same sample rate. The PCM/I2S bridge accepts voice data in mono PCM format at a particular sample rate from a Bluetooth transceiver. The incoming PCM audio data is then converted to a stereo I2S format and is sent out through the LM49370’s I2S output port over to the baseband processor for transmit. The PCM/I2S bridge accepts voice data in stereo I2S format from the baseband processor. The left and right I2S data can then be summed together and converted to a mono PCM format. The converted mono PCM music data is then routed to the Bluetooth transceiver via the LM49370’s PCM output port for voice receive. For systems that use a dedicated RF IC for voice receive and transmit, the LM49370 features a differential analog input (CP_IN) and output (CP_OUT) pair that directly connect to the analog interface of the RF IC while the LM49370’s PCM port still directly interfaces with the Bluetooth transceiver. This an alternative to using the PCM/I2S bridge for two way voice communication via a Bluetooth headset (see Figure 12). One limitation of the PCM/I2S Bridge is that both the PCM and I2S interfaces of the LM49370 should not simultaneously operate as slaves. Both the PCM and I2S interfaces can run as masters, or one master and the other slave. However, it is not recommended to run both interfaces as slaves if the PCM and I2S clock sources cannot be synchronized exactly. When using the PCM/I2S Bridge, set the FORCERQ bit to ‘1’ to activate the LM49370’s R and Q dividers (see Figure 9) which allow PCM or I2S clock generation in master mode. The compression format of the PCM interface is transparent to the PCM/I2S bridge. The PCM interface can operate in linear mode, A-law compressed, or μ-law compressed without any impact on PCM/I2S bridge operation. The I2S bus format (standard or left justified) is also transparent to the PCM/I2S bridge. The PCM/I2S bridge operates with minimal power consumption and also supports sample rate conversion (SRC). However, there are three primary modes of PCM/I2S Bridge operation which are dependent on the sample rates of the PCM and I2S buses. To better understand the different models of operation, two sample rate “families” have been identified, 48kHz and 44.1kHz. The 48kHz sample rate family consists of 8kHz, 16kHz, 24kHz, 32kHz, and 48kHz. The 44.1kHz sample rate family consists of 11.025kHz, 22.05kHz, and 44.1kHz. The three modes of operation of the PCM/I2S Bridge are: 1. The PCM and I2S interfaces run at the same sample rate without sample rate conversion. 2. The PCM and I2S interfaces run at different sample rates that are within the same sample rate family. 3. The PCM and I2S interfaces run at different sample rates that are not of the same family. ADC_SRC_MODE PCM_TX_SEL IIR Dec PCM_SDI CIC PCM PCM_SDO Mono ADC Sample & Hold 2 I S_TX_SEL STEREO/ MONO MONO_SUM_MODE MONO_SUM_SEL 2 at fS(IN) FIR Interp Stereo DAC DAC_INPUT_SEL Automatic Handshaking DSDM 2 2 I S_SDI I S I S_SDO DAC_SRC_MODE Figure 3. Overall PCM/I2S Bridge Diagram 4 AN-1591 LM49370 PCM/I2S Bridge SNAA039A – July 2007 – Revised May 2013 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated PCM and I2S Running at the Same Sample Rate www.ti.com 3 PCM and I2S Running at the Same Sample Rate The recommended PCM/I2S Bridge mode of operation is to have both the PCM and I2S interfaces run at the same sample rate. This mode of operation consumes the least amount of power because there is no sample rate conversion. The LM49370’s stereo DAC and mono ADC can both be completely powered off in this mode of operation. For voice recording through the Bluetooth headset, set I2S_TX_SELECT to ‘01’ (PCM Receiver) as this will route the mono PCM data received from PCM_SDI to I2S_SDO. The mono signal is automatically copied onto both the left and right channels of the I2S bus. For MP3/MP4 playback (or voice receive via the baseband processor) through the Bluetooth headset, set PCM_TX_SELECT to ‘1’ (Mono Sum Circuit) as this will route the stereo I2S data received from I2S_SDI to PCM_SDO via the mono sum circuit. The mono sum circuit acts like a stereo to mono converter. It takes the stereo I2S data and produces a mono output. The mono output can be either the I2S left channel, the I2S right channel, or a mono signal created by adding the left and right I2S channels. This is controlled by MONO_SUM_MODE. This is also the only PCM/I2S Bridge mode of operation that allows two-way voice communication via Bluetooth headset for systems that implement the baseband processor’s I2S port for voice receive and transmit. Table 1. PCM/I2S Bridge Settings (I2S and PCM Operating at the Same Sample Rate) I2C Field (1) (1) Setting Result PCM_TX_SEL 1 Mono Sum Circuit PCM Receiver I2S_TX_SEL 01 DAC_INPUT_SEL 11 Disabled MONO_SUM_SEL 1 I2S Receiver MONO_SUM_MODE 00 Mono Out = (Left I2S + Right I2S) / 2 ADC_SRC_MODE 0 Disabled DAC_SRC_MODE 0 Disabled 2 Refer to the LM49370 datasheet for detailed information regarding the I C register settings. PCM_TX_SEL PCM_SDO PCM PCM_SDI Automatic Handshaking 2 I S_TX_SEL STEREO/ MONO MONO_SUM_MODE MONO_SUM_SEL 2 2 2 I S_SDI I S I S_SDO Figure 4. PCM and I2S Running at the Same Sample Rate (Voice Communication, Voice Record, or MP3/MP4 Playback) AN-1591 LM49370 PCM/I2S Bridge SNAA039A – July 2007 – Revised May 2013 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated 5 I2S and PCM Running at Different Sample Rates Within the Same Sample Rate Family 4 www.ti.com I2S and PCM Running at Different Sample Rates Within the Same Sample Rate Family In the case of system level restraints, the I2S and PCM interfaces may have to operate at different sample rates while running simultaneously. The PCM/I2S Bridge can be used as a sample rate converter either to upsample or downsample the incoming data stream. As long as the sample rates of the I2S and PCM interfaces are within the same sample rate family, portions of the LM49370’s stereo DAC and mono ADC can be powered down. This mode of operation consumes more power due to the sample rate conversion process. Therefore, it is recommended to avoid sample rate conversion if it is not required. This mode requires access to the stereo DAC’s interpolated output. The interpolated DAC output can be resampled directly through the I2S interface or it can be sent to the mono sum circuit and then fed to the Sample and Hold block. The output of the Sample and Hold block is then decimated by the ADC’s IIR filter. The resulting ADC output can then be routed to either the I2S or PCM interface. Throughout this document, there will be many references to fS(IN) and fS(OUT). The variable fS(IN) represents the sample rate of the receiving interface (I2S or PCM) of the PCM/I2S Bridge, and fS(OUT) represents the sample rate of the transmitting interface (I2S or PCM) of the PCM/I2S Bridge. For Bluetooth voice recording, fS(IN) represents the PCM sample rate and fS(OUT) represents the I2S sample rate. For Bluetooth MP3/MP4 playback, fS(IN) represents the I2S sample rate and fS(OUT) represents the PCM sample rate. The I2S (or PCM) interface can directly resample the DAC’s interpolated output only if the following conditions are met: Condition 1: fS(IN) < fS(OUT) , which is equivalent to upsampling Condition 2: ((fS(IN) / fS(OUT)) * (OSR)) = an integer number, where OSR is the oversampling ratio of the DAC and ADC. If these conditions are not met, then the interpolated DAC output has to be resampled using the Sample and Hold block. One such scenario that requires the use of the Sample and Hold block is converting an fS(IN) of 8kHz to an fS(OUT) of 24kHz. Assuming an OSR of 128, Condition 2 is violated because ((8kHz) / 24kHz) × (128)) results in a non-integer value of 42.667. Another scenario that requires the use of the Sample and Hold block is downsampling an fS(IN) of 48kHz to an fS(OUT) of 8kHz, which is violation of Condition 1. It is important to note that the DAC and ADC can operate with an OSR of 125 or 128. ADC_SRC_MODE PCM_SDI PCM IIR Dec Mono ADC Sample & Hold 2 I S_TX_SEL STEREO/ MONO MONO_SUM_MODE MONO_SUM_SEL 2 2 I S I S_SDO at fS(IN) DAC_INPUT_SEL Automatic Handshaking FIR Interp Stereo DAC DAC_SRC_MODE Figure 5. PCM and I2S Running at Different Sample Rates Within the Same Sample Rate Family (Voice Record) 6 AN-1591 LM49370 PCM/I2S Bridge SNAA039A – July 2007 – Revised May 2013 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated I2S and PCM Running at Different Sample Rates Within the Same Sample Rate Family www.ti.com ADC_SRC_MODE PCM_TX_SEL IIR Dec PCM PCM_SDO Mono ADC Sample & Hold STEREO/ MONO MONO_SUM_MODE 2 2 I S_SDI I S MONO_SUM_SEL at fS(IN) DAC_INPUT_SEL Automatic Handshaking FIR Interp Stereo DAC DAC_SRC_MODE Figure 6. PCM and I2S Running at Different Sample Rates Within the Same Sample Rate Family (MP3/MP4 Playback) The following tables can be used as a guide to correctly set the PCM/I2S Bridge where fS(IN) and fS(OUT) are from the same sample rate family: Although the tables only cover the 48kHz sample rate family, the same principles can be applied to sample rate conversion within the 44.1kHz sample rate family. AN-1591 LM49370 PCM/I2S Bridge SNAA039A – July 2007 – Revised May 2013 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated 7 I2S and PCM Running at Different Sample Rates Within the Same Sample Rate Family www.ti.com Table 2. Converting 8kHz to Other Sample Rates Within the Same Family (OSR = 128) fS(IN) 8kHz fS(OUT) MP3 Playback Settings 8kHz Refer to Table 1 Refer to Table 1 16kHz PCM_TX_SELECT = X PCM_TX_SELECT = 1 I2S_TX_SELECT = 10 I2S_TX_SELECT = XX DAC_INPUT_SEL = 01 DAC_INPUT_SEL = 00 MONO_SUM_SEL = 0 MONO_SUM_SEL = 0 MONO_SUM_MODE = 00 MONO_SUM_MODE = 00 ADC_SRC_MODE = 0 ADC_SRC_MODE = 0 DAC_SRC_MODE = 1 DAC_SRC_MODE = 1 PCM_TX_SELECT = X PCM_TX_SELECT = 0 I2S_TX_SELECT = 00 I2S_TX_SELECT = XX DAC_INPUT_SEL = 01 DAC_INPUT_SEL = 00 MONO_SUM_SEL = 0 MONO_SUM_SEL = 0 MONO_SUM_MODE = 00 MONO_SUM_MODE = 00 ADC_SRC_MODE = 1 ADC_SRC_MODE = 1 DAC_SRC_MODE = 1 DAC_SRC_MODE = 1 PCM_TX_SELECT = X PCM_TX_SELECT = 1 I2S_TX_SELECT = 10 I2S_TX_SELECT = XX DAC_INPUT_SEL = 01 DAC_INPUT_SEL = 00 MONO_SUM_SEL = 0 MONO_SUM_SEL = 0 MONO_SUM_MODE = 00 MONO_SUM_MODE = 00 ADC_SRC_MODE = 0 ADC_SRC_MODE = 0 DAC_SRC_MODE = 1 DAC_SRC_MODE = 1 PCM_TX_SELECT = X PCM_TX_SELECT = 0 I2S_TX_SELECT = 00 I2S_TX_SELECT = XX DAC_INPUT_SEL = 01 DAC_INPUT_SEL = 00 MONO_SUM_SEL = 0 MONO_SUM_SEL = 0 MONO_SUM_MODE = 00 MONO_SUM_MODE = 00 ADC_SRC_MODE = 1 ADC_SRC_MODE = 1 DAC_SRC_MODE = 1 DAC_SRC_MODE = 1 24kHz 32kHz 48kHz 8 Voice Record Settings AN-1591 LM49370 PCM/I2S Bridge SNAA039A – July 2007 – Revised May 2013 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated I2S and PCM Running at Different Sample Rates Within the Same Sample Rate Family www.ti.com Table 3. Converting 16kHz to Other Sample Rates Within the Same Family (OSR = 128) fS(IN) fS(OUT) 16kHz 8kHz Voice Record Settings MP3 Playback Settings PCM_TX_SELECT = X PCM_TX_SELECT = 0 I2S_TX_SELECT = 00 I2S_TX_SELECT = XX DAC_INPUT_SEL = 01 DAC_INPUT_SEL = 00 MONO_SUM_SEL = 0 MONO_SUM_SEL = 0 MONO_SUM_MODE = 00 MONO_SUM_MODE = 00 ADC_SRC_MODE = 1 ADC_SRC_MODE = 1 DAC_SRC_MODE = 1 DAC_SRC_MODE = 1 16kHz Refer to Table 1 Refer to Table 1 24kHz PCM_TX_SELECT = X PCM_TX_SELECT = 0 I2S_TX_SELECT = 00 I2S_TX_SELECT = XX DAC_INPUT_SEL = 01 DAC_INPUT_SEL = 00 MONO_SUM_SEL = 0 MONO_SUM_SEL = 0 MONO_SUM_MODE = 00 MONO_SUM_MODE = 00 ADC_SRC_MODE = 1 ADC_SRC_MODE = 1 DAC_SRC_MODE = 1 DAC_SRC_MODE = 1 PCM_TX_SELECT = X PCM_TX_SELECT = 1 I2S_TX_SELECT = 10 I2S_TX_SELECT = XX DAC_INPUT_SEL = 01 DAC_INPUT_SEL = 00 MONO_SUM_SEL = 0 MONO_SUM_SEL = 0 MONO_SUM_MODE = 00 MONO_SUM_MODE = 00 ADC_SRC_MODE = 0 ADC_SRC_MODE = 0 DAC_SRC_MODE = 1 DAC_SRC_MODE = 1 PCM_TX_SELECT = X PCM_TX_SELECT = 0 I2S_TX_SELECT = 00 I2S_TX_SELECT = XX DAC_INPUT_SEL = 01 DAC_INPUT_SEL = 00 MONO_SUM_SEL = 0 MONO_SUM_SEL = 0 MONO_SUM_MODE = 00 MONO_SUM_MODE = 00 ADC_SRC_MODE = 1 ADC_SRC_MODE = 1 DAC_SRC_MODE = 1 DAC_SRC_MODE = 1 32kHz 48kHz AN-1591 LM49370 PCM/I2S Bridge SNAA039A – July 2007 – Revised May 2013 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated 9 I2S and PCM Running at Different Sample Rates Within the Same Sample Rate Family www.ti.com Table 4. Converting 24kHz to Other Sample Rates Within the Same Family (OSR = 128) fS(IN) fS(OUT) 24kHz 8kHz 16kHz MP3 Playback Settings PCM_TX_SELECT = X PCM_TX_SELECT = 0 I2S_TX_SELECT = 00 I2S_TX_SELECT = XX DAC_INPUT_SEL = 01 DAC_INPUT_SEL = 00 MONO_SUM_SEL = 0 MONO_SUM_SEL = 0 MONO_SUM_MODE = 00 MONO_SUM_MODE = 00 ADC_SRC_MODE = 1 ADC_SRC_MODE = 1 DAC_SRC_MODE = 1 DAC_SRC_MODE = 1 PCM_TX_SELECT = X PCM_TX_SELECT = 0 I2S_TX_SELECT = 00 I2S_TX_SELECT = XX DAC_INPUT_SEL = 01 DAC_INPUT_SEL = 00 MONO_SUM_SEL = 0 MONO_SUM_SEL = 0 MONO_SUM_MODE = 00 MONO_SUM_MODE = 00 ADC_SRC_MODE = 1 ADC_SRC_MODE = 1 DAC_SRC_MODE = 1 DAC_SRC_MODE = 1 24kHz Refer to Table 1 Refer to Table 1 32kHz PCM_TX_SELECT = X PCM_TX_SELECT = 1 I2S_TX_SELECT = 10 I2S_TX_SELECT = XX DAC_INPUT_SEL = 01 DAC_INPUT_SEL = 00 MONO_SUM_SEL = 0 MONO_SUM_SEL = 0 MONO_SUM_MODE = 00 MONO_SUM_MODE = 00 ADC_SRC_MODE = 0 ADC_SRC_MODE = 0 DAC_SRC_MODE = 1 DAC_SRC_MODE = 1 PCM_TX_SELECT = X PCM_TX_SELECT = 1 I2S_TX_SELECT = 10 I2S_TX_SELECT = XX DAC_INPUT_SEL = 01 DAC_INPUT_SEL = 00 MONO_SUM_SEL = 0 MONO_SUM_SEL = 0 MONO_SUM_MODE = 00 MONO_SUM_MODE = 00 ADC_SRC_MODE = 0 ADC_SRC_MODE = 0 DAC_SRC_MODE = 1 DAC_SRC_MODE = 1 48kHz 10 Voice Record Settings AN-1591 LM49370 PCM/I2S Bridge SNAA039A – July 2007 – Revised May 2013 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated I2S and PCM Running at Different Sample Rates Within the Same Sample Rate Family www.ti.com Table 5. Converting 32kHz to Other Sample Rates Within the Same Family (OSR = 128) fS(IN) fS(OUT) 32kHz 8kHz 16kHz 24kHz Voice Record Settings MP3 Playback Settings PCM_TX_SELECT = X PCM_TX_SELECT = 0 I2S_TX_SELECT = 00 I2S_TX_SELECT = XX DAC_INPUT_SEL = 01 DAC_INPUT_SEL = 00 MONO_SUM_SEL = 0 MONO_SUM_SEL = 0 MONO_SUM_MODE = 00 MONO_SUM_MODE = 00 ADC_SRC_MODE = 1 ADC_SRC_MODE = 1 DAC_SRC_MODE = 1 DAC_SRC_MODE = 1 PCM_TX_SELECT = X PCM_TX_SELECT = 0 I2S_TX_SELECT = 00 I2S_TX_SELECT = XX DAC_INPUT_SEL = 01 DAC_INPUT_SEL = 00 MONO_SUM_SEL = 0 MONO_SUM_SEL = 0 MONO_SUM_MODE = 00 MONO_SUM_MODE = 00 ADC_SRC_MODE = 1 ADC_SRC_MODE = 1 DAC_SRC_MODE = 1 DAC_SRC_MODE = 1 PCM_TX_SELECT = X PCM_TX_SELECT = 0 I2S_TX_SELECT = 00 I2S_TX_SELECT = XX DAC_INPUT_SEL = 01 DAC_INPUT_SEL = 00 MONO_SUM_SEL = 0 MONO_SUM_SEL = 0 MONO_SUM_MODE = 00 MONO_SUM_MODE = 00 ADC_SRC_MODE = 1 ADC_SRC_MODE = 1 DAC_SRC_MODE = 1 DAC_SRC_MODE = 1 32kHz Refer to Table 1 Refer to Table 1 48kHz PCM_TX_SELECT = X PCM_TX_SELECT = 0 I2S_TX_SELECT = 00 I2S_TX_SELECT = XX DAC_INPUT_SEL = 01 DAC_INPUT_SEL = 00 MONO_SUM_SEL = 0 MONO_SUM_SEL = 0 MONO_SUM_MODE = 00 MONO_SUM_MODE = 00 ADC_SRC_MODE = 1 ADC_SRC_MODE = 1 DAC_SRC_MODE = 1 DAC_SRC_MODE = 1 AN-1591 LM49370 PCM/I2S Bridge SNAA039A – July 2007 – Revised May 2013 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated 11 I2S and PCM Running at Different Sample Rates Within the Same Sample Rate Family www.ti.com Table 6. Converting 48kHz to Other Sample Rates Within the Same Family (OSR = 128) fS(IN) fS(OUT) 48kHz 8kHz 16kHz 24kHz 32kHz 48kHz Voice Record Settings MP3 Playback Settings PCM_TX_SELECT = X PCM_TX_SELECT = 0 I2S_TX_SELECT = 00 I2S_TX_SELECT = XX DAC_INPUT_SEL = 01 DAC_INPUT_SEL = 00 MONO_SUM_SEL = 0 MONO_SUM_SEL = 0 MONO_SUM_MODE = 00 MONO_SUM_MODE = 00 ADC_SRC_MODE = 1 ADC_SRC_MODE = 1 DAC_SRC_MODE = 1 DAC_SRC_MODE = 1 PCM_TX_SELECT = X PCM_TX_SELECT = 0 I2S_TX_SELECT = 00 I2S_TX_SELECT = XX DAC_INPUT_SEL = 01 DAC_INPUT_SEL = 00 MONO_SUM_SEL = 0 MONO_SUM_SEL = 0 MONO_SUM_MODE = 00 MONO_SUM_MODE = 00 ADC_SRC_MODE = 1 ADC_SRC_MODE = 1 DAC_SRC_MODE = 1 DAC_SRC_MODE = 1 PCM_TX_SELECT = X PCM_TX_SELECT = 0 I2S_TX_SELECT = 00 I2S_TX_SELECT = XX DAC_INPUT_SEL = 01 DAC_INPUT_SEL = 00 MONO_SUM_SEL = 0 MONO_SUM_SEL = 0 MONO_SUM_MODE = 00 MONO_SUM_MODE = 00 ADC_SRC_MODE = 1 ADC_SRC_MODE = 1 DAC_SRC_MODE = 1 DAC_SRC_MODE = 1 PCM_TX_SELECT = X PCM_TX_SELECT = 0 I2S_TX_SELECT = 00 I2S_TX_SELECT = XX DAC_INPUT_SEL = 01 DAC_INPUT_SEL = 00 MONO_SUM_SEL = 0 MONO_SUM_SEL = 0 MONO_SUM_MODE = 00 MONO_SUM_MODE = 00 ADC_SRC_MODE = 1 ADC_SRC_MODE = 1 DAC_SRC_MODE = 1 DAC_SRC_MODE = 1 Refer to Table 1 Refer to Table 1 Table 7. Converting any 48kHz Related Sample Rate to Other Sample Rates Within the Same Family (OSR = 125) fS(IN) Any 48kHz Related Sample Rate 12 fS(OUT) Any 48kHz Related Sample Rate that is not fS(IN) Voice Record Settings MP3 Playback Settings PCM_TX_SELECT = X PCM_TX_SELECT = 0 I2S_TX_SELECT = 00 I2S_TX_SELECT = XX DAC_INPUT_SEL = 01 DAC_INPUT_SEL = 00 MONO_SUM_SEL = 0 MONO_SUM_SEL = 0 MONO_SUM_MODE = 00 MONO_SUM_MODE = 00 ADC_SRC_MODE = 1 ADC_SRC_MODE = 1 DAC_SRC_MODE = 1 DAC_SRC_MODE = 1 AN-1591 LM49370 PCM/I2S Bridge SNAA039A – July 2007 – Revised May 2013 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated PCM and I2S Running at Sample Rates from Different Sample Rate Families www.ti.com 5 PCM and I2S Running at Sample Rates from Different Sample Rate Families Whenever the sample rates of the I2S and PCM interfaces are running at sample rates from different sample rate families (for example fS(IN) = 44.1kHz and fS(OUT) = 8kHz), the PCM/I2S bridge requires that the stereo DAC and mono ADC be fully turned on. The incoming digital audio path (either I2S or PCM) has to be routed to the stereo DAC in order to do the complete digital to analog conversion. The left and right analog DAC outputs are then summed together and routed back through the ADC in order to perform the analog to digital conversion. Because the entire portion of both the stereo DAC and mono ADC have to be turned on, this particular PCM/I2S bridge mode of operation consumes the most amount of power. This mode of operation is not preferred, but because of system level restrictions this mode of operation may be the only alternative. There are also limitations on the master clock frequency (MCLK) for this particular mode of operation. The LM49370 has one available PLL. This PLL can be used to generate the required frequencies from one sample rate family. The required clock frequencies from the other sample rate family must be directly divided down from MCLK. If the LM49370’s internal clock dividers cannot directly divide down MCLK to the required clock frequencies, the PCM/I2S Bridge cannot be used. Typically, the PLL should handle the 44.1kHz related frequencies while the 48kHz related frequencies should be divided directly from MCLK. When running the DAC and ADC in 128 OSR mode, an MCLK of 12.288MHz or 11.2896MHz or an integer factor of either clock will select PCM/I2S Bridge operation for handling sampling rates of different families. For 125 OSR mode, and MCLK of 12MHz or 11.025MHz or an integer factor of either clock will select PCM/I2S Bridge operation for handling sample rates of different families. If a 13MHz MCLK or an integer factor of that clock is available, the internal dividers can generate an 8kHz sample rate in 125 OSR mode, while the PLL can handle the 44.1kHz related frequencies. Table 8. Converting a Sample Rate to Another Sample Rate from a Different Sample Rate Family fS(IN) Any 44.1kHz Related Sample Rate Any 48kHz Related Sample Rate fS(OUT) Any 48kHz Related Sample Rate Any 44.1kHz Related Sample Rate Voice Record Settings MP3 Playback Settings PCM_TX_SELECT = X PCM_TX_SELECT = 0 I2S_TX_SELECT = 00 I2S_TX_SELECT = XX DAC_INPUT_SEL = 01 DAC_INPUT_SEL = 00 MONO_SUM_SEL = X MONO_SUM_SEL = X MONO_SUM_MODE = XX MONO_SUM_MODE = XX ADC_SRC_MODE = 0 ADC_SRC_MODE = 0 DAC_SRC_MODE = 0 DAC_SRC_MODE = 0 PCM_TX_SELECT = X PCM_TX_SELECT = 0 I2S_TX_SELECT = 00 I2S_TX_SELECT = XX DAC_INPUT_SEL = 01 DAC_INPUT_SEL = 00 MONO_SUM_SEL = X MONO_SUM_SEL = X MONO_SUM_MODE = XX MONO_SUM_MODE = XX ADC_SRC_MODE = 0 ADC_SRC_MODE = 0 DAC_SRC_MODE = 0 DAC_SRC_MODE = 0 AN-1591 LM49370 PCM/I2S Bridge SNAA039A – July 2007 – Revised May 2013 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated 13 PCM and I2S Running at Sample Rates from Different Sample Rate Families www.ti.com IIR Dec CIC PCM PCM_SDI ADSM ADC_SRC_MODE Mono ADC 2 I S_TX_SEL 2 at fS(IN) FIR Interp DSDM 2 I S I S_SDO Analog LPF Stereo DAC DAC_INPUT_SEL Automatic Handshaking DAC_SRC_MODE Figure 7. PCM and I2S Running at Different Sample Rates from Different Sample Rate Families (Voice Record) ADC_SRC_MODE IIR Dec CIC PCM PCM_SDO ADSM PCM_TX_SEL at fS(IN) DAC_INPUT_SEL Automatic Handshaking FIR Interp DSDM 2 2 I S_SDI I S Mono ADC Analog LPF Stereo DAC DAC_SRC_MODE Figure 8. PCM and I2S Running at Different Sample Rates from Different Sample Rate Families (MP3/MP4 Playback) 14 AN-1591 LM49370 PCM/I2S Bridge SNAA039A – July 2007 – Revised May 2013 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated Setting the Correct Clocks www.ti.com 6 Setting the Correct Clocks For proper PCM/I2S bridge operation, it is essential to have the correct clocks running on both the PCM and I2S interfaces. The stereo DAC should operate at a clock frequency that is based on the incoming sample rate of the bridge: DAC_CLOCK = (fS(IN) * OSR) (1) The LM49370’s R divider directly divides the incoming MCLK or the PLL output clock to generate DAC_CLOCK. The mono ADC, if used, should operate at a clock frequency that is based on the outgoing sample rate of the bridge: ADC_CLOCK = (fS(OUT) * OSR) (2) The LM49370’s Q divider generates the required ADC_CLOCK. NOTE: Refer to the LM49370 datasheet on how to set the I2C registers for the PLL, R divider, Q divider, I2S port, and PCM port. USE_ONCHIP_OSC From on chip 12 MHz oscillator %R PLL A (to DET, PMC) B %Q MCLK C I2S Interface Stereo DAC PCM Interface Mono ADC I2S_CLK PCM_CLK Figure 9. LM49370 Clock Network The clock outputs of the R divider (DAC_CLOCK) and the Q divider (ADC_CLOCK) are also used to provide the required clocks for the PCM and I2S interfaces. If the I2S is running in master mode, the I2S_CLOCK_GEN block divides DAC_CLOCK (or ADC_CLOCK) to generate the required I2S clock frequency (I2S_CLOCK). The I2S_WS_GEN block divides I2S_CLOCK to generate the proper I2S sync signal (I2S_WS). The correct frequencies of I2S_WS and I2S_CLOCK are calculated by: I2S_WS = fS(I2S) (3) I2S_CLOCK = (# of bits per I2S word) × (2) × fS(I2S) (4) If the desired I2S sampling rate is 48kHz, then I2S_WS = 48kHz. Assuming an I2S word length of 16 bits, then I2S_CLOCK = 1.536MHz. AN-1591 LM49370 PCM/I2S Bridge SNAA039A – July 2007 – Revised May 2013 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated 15 Setting the Correct Clocks www.ti.com ADC_CLOCK DAC_CLOCK I2S CLKGEN I2S_CLK_OUT I2S_CLK_IN I2S_CLK I2S WSGEN I2S_WS_OUT I2S_WS I2S_WS_IN Figure 10. Audio Port CLOCK/SYNC Options If the PCM interface is running in master mode, the PCM_CLOCK_GEN block divides DAC_CLOCK (or ADC_CLOCK) to generate the required PCM clock frequency (PCM_CLOCK). The PCM_SYNC_GEN block divides PCM_CLOCK to generate the proper PCM sync signal (PCM_SYNC). The correct frequencies of PCM_SYNC and PCM_CLOCK are calculated by: PCM_SYNC = fS(PCM) (5) PCM_CLOCK = (# of bits per PCM word) × fS(PCM) (6) If the desired PCM sampling rate is 8kHz and the PCM word length is 16 bits, then PCM_SYNC = 8kHz and PCM_CLOCK = 128kHz. ADC_CLOCK DAC_CLOCK PCM CLKGEN PCM_CLK_OUT PCM_CLK_IN PCM_CLOCK PCM SYNCGEN PCM_SYNC_OUT PCM_SYNC PCM_SYNC_IN Figure 11. PCM Audio Port CLOCK/SYNC Options 16 AN-1591 LM49370 PCM/I2S Bridge SNAA039A – July 2007 – Revised May 2013 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated www.ti.com 7 Two-Way Voice Communication or Music Playback via Bluetooth Headset Without Using the PCM/I2S Bridge Two-Way Voice Communication or Music Playback via Bluetooth Headset Without Using the PCM/I2S Bridge For mobile phone designs that implement a dedicated RF IC (voice modem) for voice communication, the PCM/I2S Bridge can be bypassed as long as the RF IC has an analog interface that can connect directly to the differential inputs (CP_IN) and outputs (CP_OUT) of the LM49370. Baseband Processor Audio Port 1 2 I S (Stereo Music) 802.15.1 Bluetooth Transceiver PCM (mono) LM49370 CP_OUT Bluetooth Headset CP_IN RF Voice Module Figure 12. Using the LM49370 with a Dedicated RF Module for Two-way Voice Communication via Bluetooth Headset With this type of configuration (Figure 12), the LM49370’s I2S port is not needed for two-way voice communication. Incoming analog voice data from the RF voice module is sent from CP_IN to the LM49370's ADC. After the analog to digital conversion, the incoming voice data is routed to the Bluetooth receiver through the PCM output port. Outgoing voice data from the Bluetooth headset is sent to the LM49370's DAC through the PCM input port. After the digital to analog conversion, the outgoing voice data is sent to the RF voice module through the CP_OUT differential output for voice transmit. ADC_SRC_MODE IIR Dec PCM_SDI CIC From CP_IN PCM PCM_SDO ADSM PCM_TX_SEL FIR Interp Stereo DAC DAC_INPUT_SEL Automatic Handshaking Analog LPF To CP_OUT at fS(IN) DSDM Mono ADC DAC_SRC_MODE Figure 13. Alternative Method for Two-way Voice Communication via Bluetooth AN-1591 LM49370 PCM/I2S Bridge SNAA039A – July 2007 – Revised May 2013 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated 17 Stereo Bluetooth Headsets www.ti.com The LM49370 features a set of stereo analog inputs (AUX_L and AUX_R) that can route stereo content from a FM radio module or TV tuner module to the Bluetooth transceiver. Baseband Processor Audio Port 1 2 I S (MP3 content) 802.15.1 Bluetooth Transceiver PCM (mono) LM49370 AUX_L Bluetooth Headset AUX_R FM or TV Tuner Module Figure 14. Using the LM49370 to Route FM Radio or TV Audio to a Bluetooth Headset The analog audio content received from AUX_L and AUX_R inputs can be summed together to form a mono signal that is then routed to the ADC. After the analog to digital conversion, the mono signal is sent to the Bluetooth transceiver through the PCM output port. ADC_SRC_MODE IIR Dec CIC From (AUX_L + AUX_R) PCM PCM_SDO ADSM PCM_TX_SEL Automatic Handshaking Mono ADC Figure 15. FM Radio or TV Tuner Playback via Bluetooth Headset 8 Stereo Bluetooth Headsets The LM49370 is primarily targeted for mobile phone scenarios that require the use of a mono Bluetooth headset. For scenarios that require the use of a stereo Bluetooth headset, the Bluetooth transceiver and baseband processor must be A2DP (Advanced Audio Distribution Profile) capable. A dedicated A2DP data link is required between the baseband processor and Bluetooth transceiver for streaming music to a stereo Bluetooth headset. The LM49370 can be bypassed during A2DP operation. However, the LM49370 has built-in amplifiers to drive a wired pair of stereo headphones for non-Bluetooth applications. 9 18 Revision History Rev Date Description 1.0 07/17/07 Initial release. AN-1591 LM49370 PCM/I2S Bridge SNAA039A – July 2007 – Revised May 2013 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated