Design and Layout Guidelines for the

Application Note
SCAA045 - November 2000
Design and Layout Guidelines for the CDCVF2505 Clock
Driver
Kal Mustafa
Bus Solutions
ABSTRACT
This application note describes tuning techniques, line termination methods, and filter circuit for the
CDCVF2505, and it provides PCB layout guidelines.
1
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2
Tuning for Zero Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
3
Common Termination Techniques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1 Series Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2 Parallel Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3 Thévenin Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4 AC Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
Layout Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5
Filtering and Noise Reduction Techniques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.1 Bypass and Filter Capacitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.2 Ferrite Beads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.3 Filter Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.4 Typical Output Driver Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6
Bibliography . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5
5
8
8
8
List of Figures
1 Functional Block Diagram of CDCVF2505 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Delay vs Delta Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 Tuning for Minimum Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4 Driver Output Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
5 Series Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
6 CDCVF2505 Output Waveforms Driving Single and Dual Loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
7 Parallel Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
8 Thévenin Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
9 AC Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
10 Filter Circuit for the CDCVF2505 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
11 High-Level Output Voltage vs Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
12 Low-Level Output Voltage vs Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
List of Tables
1 Functional Comparison Between CDCVF2505 and CY2305 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2 Capacitor Values for Filtering Certain Frequencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1
SCAA045
1
Introduction
The CDCVF2505 is a high-performance, low-skew, low-jitter, phase-lock loop (PLL) clock driver
(refer to [1] for details). It uses a PLL to phase- and frequency-align the input (CLKIN) and
output (1Y[0:3], CLKOUT) clock signals precisely, and it provides integrated series-damping
resistors that make it ideal for driving point-to-point loads. Unlike many products containing
PLLs, the CDCVF2505 does not require an external RC network; instead, the loop filter for the
PLL is included on-chip, minimizing component count, space, and cost. As can be seen from
Table 1, the CDCVF2505 has performance superior to the Cypress CY2305.
Table 1. Functional Comparison Between CDCVF2505 and CY2305
FEATURE
CDCVF2505
CY2305
Number of inputs
5
5
Package
8-pin SOIC and 8-pin TSSOP
8-pin SOIC
Frequency range
24–200 MHz
1−100/133 MHz
Cycle-to-cycle jitter at 66 MHz
< 150 ps
< 200 ps
SSC compatible
Yes
No
On-chip series damping resistors
25 Ω
No
Input-to-output propagation delay
< ±150 ps
< 350 ps
Output duty cycle
45–55%
40–60%
PLL lock time
100 μs
1 ms
Rise/fall time at 0.4–2.0 V
2.5/2.5 ns
2.5/2.5 ns
Operating temperature range
−40°C–85°C
0°C–70°C
Output skew
150 ps max.
< 250 ps
Power-down feature
Yes
No
When a PLL is used in an application, data errors can be introduced as a result of (a) signal
degradation from line noise and, (b) reflections caused by improper line termination when the
signal transit time through the transmission line exceeds the rise or fall time of the signal. This
note provides guidelines and suggestions for avoiding noise and line termination problems. It
also details tuning for zero and specified nonzero delays.
2
Tuning for Zero Delay
As shown in Figure 1, the CLKOUT pin (8) completes the feedback loop of the PLL. This
connection is made inside the chip and external feedback is not required. However,CLKOUT can
be loaded with a capacitor to adjust the input-to-output propagation delay. Depending on the
application and the delay requirements, the designer can choose two capacitor values between
5 pF and 25 pF on CLKOUT to determine the exact propagation delay between CLKIN and Yn.
Native propagation delay as a function of delta load (the difference between the CKLOUT and
Yn loads) is shown in Figure 2.
When a lead-lag relationship is sought instead of a zero delay, it can be obtained by loading the
feedback pin, CLKOUT. To get a positive phase error (i.e. CLKIN leads the Y outputs), the
CLKOUT pin should be loaded more lightly than the Y outputs. Alternatively, for a more negative
phase error (Y outputs leading the reference input CLKIN), the CLOCKOUT pin should be
loaded more heavily than the Y outputs. As a rule of thumb, the adjustment is about 50 ps/pF of
loading difference; thus, 1 pF will induce delay of 35–50 ps. A 1-inch trace of 50-Ω transmission
line in FR-4 material has about a 3-pF parasitic capacitance, or approximately a 100-ps delay.
2
Design and Layout Guidelines for the CDCVF2505 Clock Driver
SCAA045
CLKIN
1
8
PLL
25 Ω
3
25 Ω
2
25 Ω
CLKOUT
1Y0
1Y1
Powerdown
5
25 Ω
7
25 Ω
Edge Detect
Typical < 10 MHz
1Y2
1Y3
3−State
Figure 1. Functional Block Diagram of CDCVF2505
Note that adjusting the trace length of the feedback loop coarse-tunes the phase error. Adjusting
the capacitive loading on the feedback is the best way to fine tune the phase error, with this
loading being placed as close to the CLKOUT pin as physically possible. For example, for a
phase lead (CLKIN lead Yn), the trace length of the Y outputs is increased. Conversely,
increasing the trace length of the feedback path decreases the phase error and, in this case, the
Yn outputs are advanced relative to the reference clock input (CLKIN).
Design and Layout Guidelines for the CDCVF2505 Clock Driver
3
SCAA045
PROPAGATION DELAY TIME
vs
DELTA LOAD
1400
t pd − Propagation Delay Time − ps
1050
700
350
0
−350
−700
CLKOUT = 12 pF||500 Ω
Yn = 25 pF||500 Ω
−1050
−1400
−25 −20 −15 −10 −5
0
5
10
15
20
25
Delta Load − pF
Figure 2. Delay vs Delta Load
PROPAGATION DELAY TIME
vs
FREQUENCY
100
t pd − Propagation Delay Time − ps
CLKOUT = 21 pF||500 Ω
Yn = 25 pF||500 Ω
50
0
−50
−100
0
50
100
150
f − Frequency − MHz
Figure 3. Tuning for Minimum Delay
4
Design and Layout Guidelines for the CDCVF2505 Clock Driver
200
SCAA045
3
Common Termination Techniques
As a general rule, transmission line (trace) termination is necessary when the round trip
propagation time of the signal is equal to or greater than the transition (rise or fall) time of the
driver; otherwise, there will be data errors caused by signal degradation, line noise, and,
reflections.
Most termination methods rely on impedance matching of the line with either the source or the
load. There are several termination techniques that can be used to terminate transmission lines.
These are series (source), parallel, Thévenin, and ac termination. Each has its advantages and
disadvantages, although ac termination has the widest general endorsement.
Excluding the series damping resistor, the typical output characteristic of the CDCVF2505 driver
shown in Figure 4 is a PMOS impedance of 12 Ω and an NMOS impedance of 15 Ω. Therefore,
the total output impedence of the driver when the output is high is approximately 37 Ω (12 + 25)
and 40 Ω (15 + 25) when the driver is low.
VDD
12 Ω
(When On)
25 Ω
15 Ω
(When On)
Figure 4. Driver Output Impedance
3.1
Series Termination
In series termination, a resistor is added to the outputs of the driver, thereby increasing the
impedance at the line source and preventing signal reflection off the driver end. The resistor
value is chosen to match the source and trace impedances. This is shown schematically in
Figures 5(a) and 5(b) for single and dual transmission lines, respectively.
Design and Layout Guidelines for the CDCVF2505 Clock Driver
5
SCAA045
RS
Zo = 50 Ω
25 Ω
4 pF
Driver
37/40 + RS = Zo
a)
Zo = 50 Ω
4 pF
25 = Zo||Zo
25 Ω
Driver
Zo = 50 Ω
4 pF
b)
Figure 5. Series Termination
Series termination is effective in reducing the driver’s edge rate, and it consumes low power. It is
recommended for single receiver, point-to-point and star topologies. Series termination provides
good signal quality by damping overshoot and undershoot, and effectively reducing line noise
and EMI. Its drawbacks are that it slows the signal’s rise and fall time, and that it should not be
used with distributed loads. The CDCVF2505 can be used to drive one or two 50-Ω transmission
lines each. In the dual-transmission-line case, there is no need to add any external series
resistor to the outputs because the CDCVF2505 has an integrated 25-Ω resistor included on
chip. Conversely, in the single-transmission-line case, an additional 25-Ω resistor should be
added as close as possible to the outputs of the CDCVF2505. In both cases the CDCVF2505
provides optimal performance with minimal overshoot and undershoot, as can be seen from
Figure 6. This figure shows simulated signal integrity of the output buffer at 133 MHz and a 4-pF
load driving single and dual transmission lines. The plot does not reflect the actual duty cycle of
the PLL; rather, the similation was done for the output buffer only. The CDCVF2505 corrects the
output duty cycle of the PLL to 50%, independent of the input duty cycle.
6
Design and Layout Guidelines for the CDCVF2505 Clock Driver
SCAA045
Wave
Symbol
D0:A3:v(outa1)
D0:A1:v(outa1)
* hspice test bench for cdc devices
3.4
3.2
3
2.8
2.6
2.4
Dual Loads (4pF each)
2.2
2
Voltages (lin)
1.8
1.6
1.4
1.2
1
800m
600m
400m
200m
Single Load (4pF)
0
−200m
30n
40n
Time (lin) (TIME)
Figure 6. CDCVF2505 Output Waveforms Driving Single and Dual Loads
Design and Layout Guidelines for the CDCVF2505 Clock Driver
7
SCAA045
3.2
Parallel Termination
Parallel termination is simple to implement. It uses a single resistor at the load end of the trace,
as shown in Figure 7 and, like the Thévenin and ac methods, it acts by preventing signal
reflection from the load end. The value of the termination resistor should be such that the load
and line impedances match. In essence, the termination resistor absorbs and dissipates energy
that would otherwise reflect.
There are a few disadvantages to this method: It consumes a large amount of power, it produces
unbalanced rise and fall times which result in duty cycle distortion, and it degrades the high
output level of the signal.
Zo = 50 Ω
25 Ω
R = Zo
Driver
4 pF
R
Figure 7. Parallel Termination
3.3
Thévenin Termination
Thévenin termination uses two load-end resistors whose parallel combination must result in
matching between the load and trace impedances. This is shown schematically in Figure 8.
VCC
R1
Zo = 50 Ω
25 Ω
Driver
R2
4 pF
R1||R2 = Zo
Figure 8. Thévenin Termination
The termination resistors are a pullup and pulldown pair that help balance the driver’s high- and
low-logic levels. This method enhances the fan-out capability of the driver, and it reduces power
consumption caused by duty cycle distortion. A disadvantage is the constant dc-current leakage
from VCC to GND regardless of the driver’s logic state.
3.4
AC Termination
Here, an RC high-pass filter is used to terminate the load end of the trace (see Figure 9). AC
termination is recommended for backplanes, cables, distributed loads, and clocks drivers. It
generates no power dissipation and permits loads to be added anywhere along the transmission
line. To avoid overshoot and undershoot, the RC time constant should be greater than the
transmission line’s round-trip propagation time. The capacitor serves to block low-frequency
noise and considerably reduces quiescent power dissipation while minimizing overshoot and
undershoot.
8
Design and Layout Guidelines for the CDCVF2505 Clock Driver
SCAA045
Zo = 50 Ω
25 Ω
Driver
R = Zo
4 pF
R
C
Figure 9. AC Termination
4
Layout Guidelines
The following suggestions are offered to aid PCB layout:
5
•
Isolate the power pin of the clock driver from the power plane of the board by a ferrite bead.
The ferrite prevents high-frequency noise from reaching the main power supply.
•
Minimize EMI by avoiding the use of vias to route clock signals. Vias add unwanted
inductance to the trace and in general reduce the effectiveness of bypass capacitors.
•
To minimize reflections and ringing, keep traces short and impedance balanced
•
If possible, place clock signals far away from data busses.
•
Load all outputs equally.
•
Avoid routing traces near the edge of the PCB board.
•
Clock traces should not cross each other. They should also be of equal length to minimize
clock skew.
•
Route clock traces point-to-point and terminate them individually.
•
Keep power and ground planes close together. This reduces power-supply noise.
•
Place power-supply decoupling capacitors and filter components as close to VCC as
possible. For decoupling, it is recommended to use low-inductance, low-ESR (equivalent
series resistance) capacitors because they provide best performance.
Filtering and Noise Reduction Techniques
The following provides general guidelines for reducing radiated emissions and improving signal
quality of PLL clock generators. Also discussed are power-supply and ground-noise reduction
techniques through decoupling, and the use of both bypass capacitors and ferrite beads.
5.1
Bypass and Filter Capacitors
Filter capacitors are used to eliminate low-frequency power-supply noise. A popular filter
capacitor is a surface mount 22-μF ceramic device connected as close to the power supply as
physically possible.
Design and Layout Guidelines for the CDCVF2505 Clock Driver
9
SCAA045
Bypass capacitors, on the other hand, are used to provide a very-low-impedance path for
current surges between VCC and GND at high frequency. Also, they guard the power system
against induced fluctuations. It is recommended to use mica or monolithic, ceramic-type
capacitors because they are small, inexpensive and, most importantly, they have very low
equivalent series inductance (ESL) and series equivalent resistance (ESR). The precise value
for a bypass capacitor can be determined as follows (see also Johnson and Graham, 1993).
•
Assuming all gates are switching simultaneously, find the maximum expected step change in
current and the maximum power-supply noise. Dividing the power-supply noise by the
current change gives the maximum common-path impedance: Zmax = ΔV/ΔI.
•
Find the inductance, L, of the power-supply wiring, then calculate the 3-dB or knee
frequency using the equation f = Zmax /(2πL).
•
Calculate the capacitance, C, of the bypass capacitor according to C = 1/(2πfZmax ).
This kind of calculation is exemplified by the following: Assume (i) there is a 40-gate board with
each gate switching a 20-pF load in 2.5 ns, (ii) the power supply has a wiring inductance, L, of
100 nH, and (iii) a voltage noise margin, Vn , of 110 mV. Then
(40) ǒ20
DI + n C DV +
Dt
2.5
10 *12Ǔ(3.3)
10 *9
+ 1.056 A
The maximum impedance is
Z max +
Vn
+ 0.110 + 0.104 W
1.056
DI
Then, the frequency above which the power supply wiring requires a bypass capacitor to take
over is
f PSW +
Z max
+
(2p L)
2p
0.104
+ 166 kHz
100 10 *9
Next, the value of the bypass capacitor is calculated:
C bypass +
1
+
(2p f PSW Z max)
2p
166
1
10 3
0.104
+ 9.22 mF
This is an uncommon value, so a 10-μF capacitor is used instead. The calculation says that a
10-μF capacitor is effective at frequencies above 166 kHz. Assuming now that the 10-μF
capacitor has an ESL of 1 nH, the maximum frequency at which this bypass capacitor is
effective is
f bypass +
Z max
+
(2p ESL)
ǒ2p
0.104
+ 16.55 MHz
1 10 *9Ǔ
The 10-μF capacitor is effective over the hundredfold range from 166 kHz to 16.6 MHz.
It is good practice to use an array of small capacitors in parallel because they provide lower
series inductance at high frequency than a single large capacitor. The most common values for
bypass capacitors are: 22 μF, 4.7 μF, 0.1 μF, and 0.001 μF. The 22-μF and 4.7-μF capacitors
work well at relatively low frequency (low frequency bypass). The 0.1-μF capacitor targets the
midrange frequencies, while 0.001-μF and smaller capacitors handle high frequencies (high
frequency bypass). Choosing three or more capacitors with different values effectively filters
noise from a wider bandwidth.
10
Design and Layout Guidelines for the CDCVF2505 Clock Driver
SCAA045
As opposed to ideal capacitors, real capacitors contain additional parasitic, inductive and
resistive elements. The most important parameters are the ESL and ESR, because they act
respectively as an inductance and a resistance in series with the capacitance. They tend to
defeat the effectiveness of a bypass capacitor.
The equation for the impedance of a capacitor as a function of frequency, including ESR, is:
X(f) +
Ǹ
ESR 2 )
ǒ
2pfL * 1
2pfC
Ǔ
2
There are several ESR meters commercially available that can measure very low resistance
(below 1 Ω), and some ESR meters are 1-Ω full-scale with 10-mΩ resolution. There are other
methods for measuring ESR without using an ESR meter—further information on ESR
measurements can be found at: http://fribble.cie.rpi.edu/~repairfaq/sam/captest.htm
5.2
Ferrite Beads
By nature, PLL-based clock drivers and generators are noise-sensitive. Inserting a ferrite bead
to isolate the high-frequency noise created by the clock generator and to prevent it from
reaching the main power supply suppresses noise and reduces its spread around the PCB.
Ferrite beads neither enhance nor degrade the performance of a clock generator; they merely
provide noise isolation (power supply decoupling). It is preferable to use low-dc-impedance
ferrite, between 0 Ω and 5 Ω. However, at clock frequencies the impedance of the bead should
be at least 50 Ω under load conditions. This relatively large impedance prevents noise
generated by clock harmonics from spreading across the PCB. The impedance of a ferrite bead
is a function of frequency, size, material, and the number of turns. Because ferrite beads are
composed of ferromagnetic material that is contained within the bead, they are not susceptible
to externally-radiated magnetic fields, nor can such fields detune them. Only when temperature
rises above the Curie point will the ferrite loose its magnetic properties and become useless as a
noise-attenuating element.
The Curie temperature is material dependant and can range between 120°C and 500°C.
Although other vendors have similar products, Fair-Rite Corporation’s beads #43/44, #61, #73
are popular and meet these requirements. The #43/44 material is best-suited for noise
attenuation over the range 20–300 MHz; the #73 material is recommended for suppression over
the range 1–25 MHz; for frequencies above 200 MHz, #61 is the best choice.
5.3
Filter Circuit
Putting these components together provides good filtering for many clock generators and
especially for PLL-based clock drivers. Although the CDCVF2505 has only one VCC, it has an
integrated internal filter circuit separating the analog and digital power supplies, it works even
better with an additional external filter circuit. Figure 10 contains an example of such a circuit.
Design and Layout Guidelines for the CDCVF2505 Clock Driver
11
SCAA045
CDCVF2505
(TOP VIEW)
CLKIN
1Y1
1Y0
GND
1
8
2
7
3
6
4
5
CLKOUT
1Y3
V
DD 3.3V
Ferrite
Bead
1Y2
C2
0.1 μF
0.01 μF
0.001 μF
to System
VCC at 3.3 V
C1
NOTES: 1. C2 can be 47, 39, 10, or 4.7 μF
2. C1 is system dependent and can be found as in the example
Figure 10. Filter Circuit for the CDCVF2505
The exact value of a bypass capacitor is not as critical as having three or more different
capacitor ranges, one each for low frequency, midrange, and high frequency. For example, if the
maximum wiring impedance, Zmax, is 0.1 Ω, the value, C, of the bypass capacitor can be
calculated from the equation C = 1 / (2πfZmax). Values for some capacitors that can be used to
filter certain noise frequencies are listed in Table 2.
Table 2. Capacitor Values for Filtering Certain Frequencies
5.4
f3dB (MHz)
C (μF)
0.033
47
0.072
22
0.159
10
0.339
4.7
3.2
0.5
7.2
0.22
16
0.1
32
0.05
80
0.02
100
0.016
160
0.01
200
0.008
318
0.005
400
0.004
1600
0.001
Typical Output Driver Characteristics
Figures 11 and 12 show the output buffer characteristic impedance of the CDCVF2505 clock
driver when the driver is in high and low states, respectively. These curves provide typical output
behavior when driving both single and multiple loads. The strength of the driver is measured by
the current sourcing or sinking capabilities.
12
Design and Layout Guidelines for the CDCVF2505 Clock Driver
SCAA045
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
VOH − High-Level Output Voltage − V
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
−80
−70
−60
−50
−40
−30
−20
−10
0
IOH − High-Level Output Current − mA
Figure 11. High-Level Output Voltage vs Current
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
4.0
VOL − Low-Level Output Voltage − V
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
0
20
40
60
80
100
IOL − Low-Level Output Current − mA
Figure 12. Low-Level Output Voltage vs Current
Design and Layout Guidelines for the CDCVF2505 Clock Driver
13
SCAA045
6
Bibliography
1. CDCVF2505 3.3-V Clock Phase-Lock Loop Clock Driver, Data Sheet, Texas Instruments
Literature Number SCAS640
2. Johnson, H.W., and Graham, M. High-Speed Digital Design, Prentice Hall, 1993.
3. Application And Design Considerations For CDC5xx Phase-Lock Loop Clock Drivers,
Application Note, Texas Instruments Literature Number SCAA028.
4. EMI Prevention in Clock-Distribution Circuits, Application Note, Texas Instruments Literature
Number SCAA031.
5. Clock Distribution in High-Speed PCs, Application Note, Texas Instruments Literature Number
SCAA030.
6. Using CDC2509/2510A PLL with Spread Spectrum Clocking (SSC), Application Note, Texas
Instruments Literature Number SCAA039.
7. Fair-Rite Corp., Fair-Rite Soft Ferrites / Ferrite Products for The Electronic Industry, Product
Catalog, 14th Edition.
8. Samuel M. Goldwasser, Capacitor Testing, Safe Discharging and Other Related Information,
1994−2000. http://fribble.cie.rpi.edu/~repairfaq/sam/captest.htm.
9. The Bypass Capacitor In High-Speed Environments, Application Note, Texas Instruments
Literature Number SCBA007A.
14
Design and Layout Guidelines for the CDCVF2505 Clock Driver
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated