ELN60 series

ELN60
6 0 W S i n g l e O u t put Class 2 Switching Power Supply
series
Universal AC input / Full range
Fully isolated plastic case with IP64 level
Built-in constant current limiting circuit with adjustable OCP
level
Protections: Short circuit / Overload / Over voltage
UL1310 Class 2 power unit
Cooling by free air convection
Suitable for LED lighting and moving sign applications
IP64 design for indoor or outdoor installations
Optional Dimmer Functions: 1.1~10VDC or PWM
Controlled
Model Number
Output Volts Output Amps Efficiency OVP
Ripple & Noise O/P Adjust
LED Oper Voltage
9 Volts(DC)
12 Volts(DC)
15 Volts(DC)
24 Volts(DC)
27 Volts(DC)
48 Volts(DC)
120 mV pk-pk
120 mV pk-pk
150 mV pk-pk
150 mV pk-pk
200 mV pk-pk
250 mV pk-pk
3~9Volts
3~12Volts
3~15Volts
3~24Volts
3~27Volts
3~48Volts
SINGLE OUTPUT
*ELN60-9 (D or P)
*ELN60-12 (D or P)
*ELN60-15 (D or P)
*ELN60-24 (D or P)
*ELN60-27 (D or P)
*ELN60-48 (D or P)
5 Amps
5 Amps
4 Amps
2.5 Amps
2.3 Amps
1.3 Amps
82%
85%
86%
87%
87%
88%
11~13.5 Volts(DC)
13.8~16 Volts(DC)
17.5~21 Volts(DC)
28~32 Volts(DC)
31~35 Volts(DC)
54~60 Volts(DC)
8.7~10.5 Volts(DC)
10.8~13.2 Volts(DC)
13.5~16.5 Volts(DC)
21.6~26.4 Volts(DC)
24.3~29.7 Volts(DC)
43.2~52.8 Volts(DC)
* Note:
The Asterisk * denotes a choice of receiving this product WITH a Dimmer Control Feature. There are 2 types of dimmer Control:
1. 1.1~10VDC Control (“D” Type)
2. PWM Control (“P” Type)
See page 5 of this specification
To receive this product with the 1.1~10VDC Dimmer Control feature, simply add the letter “D” to the end of the model number (i.e. “ELN60-9D”).
To receive this product with the PWM Dimmer Control feature, simply add the letter “P” to the end of the model number (i.e. “ELN60-9P”).
If not specified, you will receive the NON Dimmer Control product ((i.e. “ELN60-9”).
WWW.ASTRODYNE.COM
ASTRODYNE USA: 1-800-823-8082
ASTRODYNE PACIFIC: 886-2-26983458
ELN60
6 0 W S i n g l e O u t put Class 2 Switching Power Supply
INPUT SPECIFICATIONS
Input Voltage Range (Note 3)
Frequency Range
Input Current (115 / 230VAC)
Inrush Current, max, Cold Start
Leakage Current
90-264VAC
47-63 Hz
1.2 Amps / 0.7 Amps max
60Amps/230VAC
0.25mAmps/240VAC
Efficiency
Harmonic Current
EMS
Dimming Control (option) See Selection Chart
EN61000-3-2,-3
EN61000-4-2,3,4,6,8,11; ENV50204; EN55024 light industry
level, criteria A
1~10Volts(DC) or PWM signal:
100Hz~3KHz
OUTPUT SPECIFICATIONS
ENVIRONMENTAL SPECIFICATIONS
Voltage and Current
See Selection Chart
Line Regulation
±1.0%
Load Regulation
±2.0%
Ripple/Noise (Note 1)
See Selection Chart
Over Voltage Protection
See Selection Chart
Shut down o/p voltage, re-power
Over Current Protection
9~12Volts(DC)
95~110%
15~48Volts(DC)
130% max
Constant current limiting, auto recov
after fault condition is removed
Voltage Tolerance (Note 2)
±5.0%
Setup, Rise Time @ FL
500ms, 30ms/230VAC
1500ms, 30ms/115VAC
Hold Up Time, typ @ FL
50ms/230VAC ; 16ms/115VAC
DC Voltage Adjust (Note 4)
See Selection Chart
Can be adjusted by internal potential meter SVR1
Current Adjust Range
-25%~3%. Can be adjusted by
internal potential meter SVR2
LED Operation Voltage (Note 5) See Selection Chart
Oper. Temperature Relative Humidity
Storage Temperature
MTBF (25°C)
Temp. Coefficient Vibration
GENERAL SPECIFICATIONS
Safety
EMI
Isolation
Resistance
UL1310 Class 2, CAN/CSA C22.2 No. 223-
-M91 (except for 48Volts); IP64 approved, design refer to TUV EN60950-1, EN61347-2-13
Compliance to EN55022(CISPR22) Class B
3 KVAC Input/Output
I/P-O/P >100MΩ / 500VDC / 25°C70%RH
All specifications are typical at nominal input, full load, and 25°C unless otherwise noted
WWW.ASTRODYNE.COM
series
-20°C to +60°C (See Derate Curve)
20~90% RH non cond
-40°C to +85°C, 10~95% RH
603KHrs min, MIL-HDBK-217F
±0.03%/°C (0~50°C)
10~500Hz, 2G 10min./1cycle, period for 60min.each along X,Y, Z axes
PHYSICAL SPECIFICATIONS
Size
Millimeters / Inches
181 x61.5 x 35 / 7.13” x 2.42” x 1.38”
Weight
14.11 oz (400g)
Notes
1. Ripple & noise are measured at 20MHz of bandwidth by using a 12”
twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
2. Tolerance : includes set up tolerance, line regulation and load regulation.
3. Derating may be needed under low input voltage. Please check the
derating curve for more details.
4. Output voltage can be adjusted through the SVR1 on the PCB ; limit
of output constant current level can be adjusted through the SVR2 on
the PCB.
5. Constant current operation region is within the specified output
voltage range. This is the suitable operation region for LED related applications.
Astrodyne products are not authorized or warranteed for use
as critical components in life support systems, equipment used
in hazardous environments, nuclear controls systems, or other
mission-critical applications.
ASTRODYNE USA: 1-800-823-8082
ASTRODYNE PACIFIC: 886-2-26983458
6 0 W S i n g l e O u t put Class 2 Switching Power Supply
ELN60
series
Mechanical Dimiension
WWW.ASTRODYNE.COM
ASTRODYNE USA: 1-800-823-8082
ASTRODYNE PACIFIC: 886-2-26983458
6 0 W S i n g l e O u t put Class 2 Switching Power Supply
WWW.ASTRODYNE.COM
ELN60
series
ASTRODYNE USA: 1-800-823-8082
ASTRODYNE PACIFIC: 886-2-26983458
6 0 W S i n g l e O u t put Class 2 Switching Power Supply
WWW.ASTRODYNE.COM
ELN60
series
ASTRODYNE USA: 1-800-823-8082
ASTRODYNE PACIFIC: 886-2-26983458
6 0 W S i n g l e O u t put Class 2 Switching Power Supply
WWW.ASTRODYNE.COM
ELN60
series
ASTRODYNE USA: 1-800-823-8082
ASTRODYNE PACIFIC: 886-2-26983458