PRODIS®-SSI

PRODIS®-SSI
PD-SSI
Digital Process Meter for Sensors with SSI output
•
•
•
•
•
Description
Specifications
For position sensors with SSI output
Integrated sensor supply
6-digit LED display
RS-232 interface
Easy programming
PRODIS®-SSI is designed for use with SSI position sensors to display angle and displacement. Via the CLOCK lines, a sequence of pulses will be transwithted, the input DATA lines
will read the sensor´s serial bit sequence. The meter is programmable to display values
within preset start/end range or values in units as inches, mm or degrees. A tare function or
programming lock can be activated with two control terminals.
Sensor excitation is supplied by the meter. With four membrane keys, all parameters can be
programmed for the special applications.
Display
Sampling rate
Excitation voltage/current
Sensor excitation
Inputs
Output
Control inputs
Connection
Operating temperature
Storage temperature
Weight
6-digit, 7-segment LED, 14 mm high,
decimal point programmable
100/s
24 V DC ±10%/150 mA, residual ripple 1%PP;
85-250 V AC, 50-60 Hz/180 mA max.
24 V DC/300 mA or 5 V DC/800 mA
DATA, DATA (RS422)
CLOCK, CLOCK (RS422)
2 control inputs 24 V, active low
Terminal strip 12-pole, excitation 3-pole
-10 ... +40 °C
-20 ... +85 °C
24 V DC: approx. 250 g; 230 V AC: approx. 400 g
Order Code PRODIS-SSI
PD-SSI
Model name
Excitation Voltage
24VDC = 24 V DC
230VAC= 85...250 V AC
Sensor Excitation
G24V = 24 V DC
G5V = 5 V DC
Options
DT = Desktop version
Order example: PD - SSI - 230VAC - G24V
PD-SSI-DAT-E-13
www.asm-sensor.com
[email protected]
1
PRODIS®-SSI
PD-SSI
Digital Process Meter for Sensors with SSI output
Specifications
(continuation)
Protection class
Humidity
Safety of equipment
Electromagnetic compatibility, EMC
Front IP60, back IP40
Max. 80 % r.h., non condensing
Directive 2006/95/EWG:
DIN EN61010-1:2010
Directive 2004/108/EWG:
DIN EN61326-1:2006
Programmable
Parameters /
Value range
Value range offset
Divisor, multiplier
Other programmable parameters
Programmable SSI parameters
Control inputs
-999999 to +999999
0 to 999999
Decimal point position, display brightness
Gray/dual code, sign, sampling rate, data format
Key lock, display value hold, tare function
Wiring basic unit
Signals
Connector X1
pin no.
Sensor excitation +UB (24 V or 5 V)
Sensor excitation 0 V (GND)
Control input 1: tare function
Control input 2: programming lock
Not used
Output CLOCK
Output CLOCK
Input DATA
Input DATA
Do not connect!
GND
PD-SSI-24VDC
Excitation +24 V
Excitation 0 V (GND)
PD-SSI-230VAC
Excitation
Protective ground
Connector X2
pin no.
1
2
3
4
5/6
7
8
9
10
11
12
13
14
13, 15
14
5 ........ 1
RS-232
Rear view without
comparator Output
RS-232 interface
Level
Data format
Transmission rate
Signals
TxD
RxD
GND
1.....................................12
13 14 15
X1
X2
RS-232: ±8 V, galvanically isolated
1 start bit, 8 data bits, 1 stop bit, no parity
4800 / 9600 / 19200 / 115200 Baud
Connector X3, pin no.
D-Sub, pin no.
17
2
16
3
18
5
Outline drawings see the following pages.
2
Fax +49 (0) 8123 986-500
Tel. +49 (0) 8123 986-0
ASM GmbH
PRODIS®-SSI
PD-SSI
Digital Process Meter for Sensors with SSI output
30
29
28
Rear view with
comparator Output
Comparator
function
(option)
Desktop version
(option)
27
26
25
24 .................................18..17..16
X3
X4
Comparator
Comparator output
NPN
Connector X3
Collector
pin no.
Comparator 1
NPN1
20
Comparator 2
NPN2
21
Comparator 3
Comparator 4
NPN3
NPN4
NPN GND
NPN UB (+24V)
22
23
24
19
RS-232
RS-232
Relay Connector X4
pin no.
LED
Relay 1
NO
NC
Common
Relay 2
NO
NC
Common
LED1
25
27
26
28
30
29
LED2
Mains switch
8 ............................. 1
15 ....................... 9
X1
85 ... 250 V AC
Wiring of connector X1 see table at page 2.
PD-SSI-DAT-E-13
www.asm-sensor.com
[email protected]
3
PRODIS®-SSI
PD-SSI
Digital Process Meter for Sensors with SSI output
Outline drawing
Cutout according to
DIN 43700
Dimensions in mm [inch]
PD-SSI-24VDC- ...
Dimensions in mm [inch]
PD-SSI-230VAC- ...
Dimensions informative only.
For guaranteed dimensions consult factory.
4
Fax +49 (0) 8123 986-500
Tel. +49 (0) 8123 986-0
ASM GmbH