PRODIS-INC Digital Process Meter for Incremental Sensors · For ASM Position Sensors and Encoders with incremental output · Integrated sensor supply · Counting rate up to 250 KHz · 6-digit LED display · Relative measurement mode · RS-232 interface · Optional 4 comparator outputs Description PRODIS-INC is designed for use with incremental position sensors to display angles and displacements. The fast counter processes 90° phase shifted A,B signals (quadrature signals) for direction and counting information. Sensor excitation is supplied from the meter. With four membrane keys all parameters can be programmed for the special application. An zero signal and a reference signal can be used for calibration of the measurement system. Optional comparator functions with 4 NPN open-collector outputs are available, 2 of them also as relay output Display 6-digit 7-segment LED, 14 mm high, decimal point programmable Excitation voltage/current Counting rate 24 V DC ±10% / 150 mA, 85-230 V AC / 180 mA max. 250 kHz maximum, 1 MHz edge frequency Specifications Sensor excitation 24 V DC/300 mA or 5 V DC/500 mA Inputs A, B, Z, T (reference signal) Connection Operation temperature Terminal strip 12-pole, excitation 3-pole -10 ... 40 °C Storage temperature -20 ... 85 °C Weight Protection class Approx. 250 g Front IP60, back IP40 Humidity 95% R.H., non condensing Comparator outputs (option) Relay NPN Electromagnetic compatibility 250 V AC/5 A, 30 V DC/5 A 24 V max./50 mA to GND Directive 73/23/EEC: DIN EN 61010:1994-03 Safety of equipment Directive 89/336/EEC Order Code PRODIS-INC PD-INC Model Name Excitation Voltage 24VDC = 24 V DC 230VAC = 230 V AC Sensor Excitation Voltage G24V = 24 V DC G5V = 5 V DC Sensor Signal HTL = HTL level TTL = TTL level Comparator (option) REL2 Order Example: PD - INC - 24VDC - G24V - HTL ASM 220503 DAB-PD-INC-E-03 1 PRODIS-INC Digital Process Meter for Incremental Sensors Programmable Parameters / Value Range Value range display, offset, limit values -999999 up to +999999 Divisor, Multiplier Other programmable parameters 0 up to 59999 Counting direction, decimal point position, last-value memory, Z signal evaluation, display brightness Manual zero, key lock, display value hold, Z release, relative measurement Signal T Signals Wiring basic equipment Connector X1 Pin No. 1 Sensor +U B Sensor 0 V (GND) Connector X2 Pin No. 2 4 Signal A Signal A 5 Signal B 6 7 Signal B Signal Z (zero signal) 8 Signal Z (zero signal) 9 10 Signal T (reference signal) Signal T (reference signal) 11 GND 12 PD-INC-24VDC Excitation +24 V 13 14 Excitation 0 V PD-INC-230VAC Excitation Protective ground 13 / 15 14 5 .......1 RS-232 1 ................................12 13 14 15 Rear view without comparator functions PD-INC-24VDC X1 X2 13 14 15 PD-INC-230VAC X1 RS-232 Interface 2 DAB-PD-INC-E-03 X2 Level RS-232: ±8 V, galvanically isolated Data format 1 start bit, 8 data bits, 1 stop bit, no parity Transmission rate 4800 / 9600 / 19200 Baud Signals Connector X3 Pin No. TxD 17 2 RxD 16 3 GND 18 5 DSUB Connector Pin No. ASM PRODIS-INC Digital Process Meter for incremental Sensors 30 29 28 27 26 25 Rear view with comparator functions Comparator functions (option) 24 23 22 21 20 19 18 17 16 X3 X4 RS-232 4 comparator outputs: 1 & 2 = relay and NPN output, 3 & 4 = NPN outputs LED 1 is on when relay 1 is in operation LED 2 is on when relay 2 is in operation Signals Connector X4 Pin No. Connector X3 Pin No. NPN1 collector NPN2 collector 20 21 NPN3 collector 22 NPN4 collector NPN GND 23 24 NPN +UB (24 V) 19 Relay1 NO Relay1 NC 25 27 Relay1 COM 26 Relay2 NO Relay2 NC 28 30 Relay2 COM 29 Zero signal Z and reference signal T Valid range ( A & B & Z ) resp. ( A & B & Z & T ) ASM DAB-PD-INC-E-03 3 PRODIS-INC Digital Process Meter for incremental Sensors Outline drawing 42,4 48 ASM Schalttafelausschnitt Cut-out according to DIN 43700 nach DIN 43700 89,5 45+0,6 96 92+0,6 PD - INC - 24VDC 9,9 55 89,5 8 9,9 32 8 PD - INC - 230VAC 4 DAB-PD-INC-E-03 ASM