Future Technology Devices International Ltd USB to RS232 Serial Converter Range of Cables Datasheet Document Reference No.: FT_000077 Version 1.3 Issue Date: 2009-12-18 Future Technology Devices International Limited (FTDI) Unit1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH United Kingdom Tel.: +44 (0) 141 429 2777 Fax: + 44 (0) 141 429 2758 E-Mail (Support): [email protected] Web: http://www.ftdichip.com Copyright © 2010 Future Technology Devices International Limited Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology Devices International Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminar y information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. . Future Technology Devices International Ltd, Unit1, 2 Seaward Place, Centurion Business Park, Glasgow, G41 1HH, United Kingdom. Scotland Registered Number: SC136640 Copyright © 2008 Future Technology Devices International Limited Document Reference No.: FT_000077 USB TO RS232 SERIAL CONVERTER RANGE OF CABLES Datasheet Version 1.3 Clearance No.: FTDI# 51 1 Description The USB_RS232 cables are a family of USB to RS232 levels serial UART converter cables incorporating FTDI’s FT232RQ USB to serial UART interface IC device which handles all the USB signalling and protocols. The cables provide a fast, simple way to connect devices with a RS232 level serial UART interface to USB. Each USB-RS232 cable contains a small internal electronic circuit board, utilising the FT232R, which is encapsulated into the USB connector end of the cable. The FT232R datasheet, DS_FT232R, is available at http://www.ftdichip.com. The integrated electronics also include the RS232 level shifter plus Tx and Rx LEDs which give a visual indication of traffic on the cable (if transparent USB connector specified). The other end of the cable is bare, tinned wire ended connections by default, but can be customised using different connectors to support various applications. Cables are FCC, CE, RoHS compliant. The USB side of the cable is USB powered and USB 2.0 full speed compatible. Each cable is 1.8m long and supports a data transfer rate up to 1 Mbaud. Each cable supports the FTDIChip-ID™, with a unique USB serial number programmed into the FT232R. This feature can be used to create a security or password protected file transfer access using the cable. Further information and examples on this feature are available at http://www.ftdichip.com under FTDIChip-ID Projects. The USB-RS232 cables require USB drivers, available free from http://www.ftdichip.com, which are used to make the FT232R in the cable appear as a virtual COM port (VCP). This then allows the user to communicate with the USB interface via a standard PC serial emulation port (for example TTY). Another FTDI USB driver, the D2XX driver, can also be used with application software to directly access the FT232R on the cable though a DLL. This is illustrated in the Figure 1.1 Various Connector Options VCP TTY Wire Ended USB_RS232 Customised connectors USB Virtual COM Port Various Connector Options Wire Ended D2XX DLL TTY USB Customised connectors Software application access to USB via D2XX Figure 1.1 Using the USB-RS232 Cable Copyright © 2010 Future Technology Devices International Limited 1 Document Reference No.: FT_000077 USB TO RS232 SERIAL CONVERTER RANGE OF CABLES Datasheet Version 1.3 Clearance No.: FTDI# 51 2 Cable Part Numbers The following Table 2.1 gives details of the available USB-RS232 cables. Part Number Description End Connector* Cable details USB to UART cable with RS232 level UART signals. USB-RS232-WE-1800-BT-0.0 Black cable, Transparent USB connector Wire Ended (no connector) 1.8m cable,6 core, UL2464 24 AWG, diam=5mm 0.0 = RED wire is 0V USB to UART cable with RS232 level UART signals. C = cable colour (B black or * T transparent), USB-RS232-CC-LLLL-CU-PWR U = USB connector colour (B CU = Connector LLLL = Length of description. cable. black or T transparent) PWR = power supply output on red wire. 0.0 = 0V, 3.3=3.3V,5.0=5V) Table 2.1 USB-RS232 Cables Descriptions and Part Numbers * FTDI supports customised end connector designs. For more information, please contact FTDI Sales Team ([email protected]) 2.1 Certifications FTDI USB-RS232 range of cables are fully RoHs compliant as well as CE and FCC certified. Copyright © 2010 Future Technology Devices International Limited 2 Document Reference No.: FT_000077 USB TO RS232 SERIAL CONVERTER RANGE OF CABLES Datasheet Version 1.3 Clearance No.: FTDI# 51 Table of Contents 1 Description ..................................................................................... 1 2 Cable Part Numbers ........................................................................ 2 2.1 3 Certifications ................................................................................................. 2 Typical Applications ........................................................................ 4 3.1 Driver Support .............................................................................................. 4 3.2 Features ........................................................................................................ 5 4 Features of FT232R applicable to USB-RS232 Cables ...................... 6 5 USB-RS232-WE-LLLL-CU ................................................................. 7 5.1 USB-RS232-WE Connections and Mechanical Details ..................................... 7 5.2 USB-RS232-WE Cable Signal Descriptions ..................................................... 8 5.3 USB-RS232-WE Electrical Parameters ........................................................... 8 6 Cable PCB Circuit Schematic ......................................................... 10 7 Contact Information ..................................................................... 11 Appendix A - Cable EEPROM Configuration ......................................... 12 Appendix B - List of Figures and Tables.............................................. 13 Appendix C - Revision History ............................................................ 14 Copyright © 2010 Future Technology Devices International Limited 3 Document Reference No.: FT_000077 USB TO RS232 SERIAL CONVERTER RANGE OF CABLES Datasheet Version 1.3 Clearance No.: FTDI# 51 3 Typical Applications USB to serial RS232 level converter. USB Instrumentation PC interface. Upgrading legacy peripherals to USB. USB industrial control. Interface Microcontroller UART or I/O to USB. USB password protected file transfers. Interface FPGA or PLD to USB. 3.1 Driver Support Royalty free VIRTUAL COM PORT Royalty free D2XX Direct Drivers (VCP) DRIVERS for... (USB Drivers + DLL S/W Interface) Windows 98, 98SE, ME, 2000, Server 2003, XP and Server 2008 Windows 98, 98SE, ME, 2000, Server 2003, XP and Server 2008 Windows XP and XP 64-bit Windows XP and XP 64-bit Windows Vista and Vista 64-bit Windows Vista and Vista 64-bit Windows XP Embedded Windows XP Embedded Windows CE 4.2, 5.0 and 6.0 Windows CE 4.2, 5.0 and 6.0 Mac OS 8/9, OS-X Linux 2.4 and greater Linux 2.4 and greater Mac OS-X The drivers listed above are all available to download for free from www.ftdichip.com. Various 3rd Party Drivers are also available for other operating systems - see www.ftdichip.com for details. Copyright © 2010 Future Technology Devices International Limited 4 Document Reference No.: FT_000077 USB TO RS232 SERIAL CONVERTER RANGE OF CABLES Datasheet Version 1.3 Clearance No.: FTDI# 51 3.2 Features USB-RS232 converter cable provides a USB to RS232 serial interface with customised end connectors. Entire USB protocol handled by the electronics in the cable USB. EIA/TIA-232 and V.28/V.24 communication interface with low power requirements. UART interface support for 7 or 8 data bits, 1 or 2 stop bits and odd / even / mark / space / no parity. Internal EEPROM with user writeable area. FTDI’s royalty-free VCP allow for communication as a standard emulated COM port and D2XX ‘direct’ drivers provide DLL application programming interface. Visual indication of Tx and Rx traffic via LEDs in the transparent USB connector. Fully assisted hardware (RTS#/CTS#) or X-On / X-Off software handshaking. Data transfer rates from 300 baud to 1 Mbaud. Support for FT232R FTDIChip-ID™ feature for improved security. Low USB bandwidth consumption. UHCI / OHCI / EHCI host controller compatible. USB 2.0 Full Speed compatible. -40°C to +85°C operating temperature range. Cable length is 1.80m (6 feet). ESD Protection for RS-232 I/O's ±15kV Human Body Model (HBM) ±15kV EN61000-4-2 Air Gap Discharge ±8kV EN61000-4-2 Contact Discharge FCC and CE compliant. Custom versions available on request (subject to MOQ). Copyright © 2010 Future Technology Devices International Limited 5 Document Reference No.: FT_000077 USB TO RS232 SERIAL CONVERTER RANGE OF CABLES Datasheet Version 1.3 Clearance No.: FTDI# 51 4 Features of FT232R applicable to USB-RS232 Cables The USB-RS232 cables use FTDI’s FT232RQ USB to serial UART IC device. This section summarises the key features of the FT232RQ which apply to the USB-RS232 USB to serial RS232 converter cables. For further details, and a full features and enhancements description consult the FT232R datasheet.This is available from www.ftdichip.com. Internal EEPROM. The internal EEPROM in each cable is used to store USB Vendor ID (VID), Product ID (PID), device serial number, product description string and various other USB configuration descriptors. Each cable is supplied with the internal EEPROM pre-programmed as described in Appendix A - Cable EEPROM Configuration. The internal EEPROM descriptors can be programmed in circuit, over USB without any additional voltage requirement. It can be programmed using the FTDI utility software called MPROG, which can be downloaded from FTDI Utilities on the FTDI website (www.ftdichip.com). Additionally, there is a user area of the internal EEPROM available to system designers to allow storing of data (note that this is not modified by MPROG). Lower Operating and Suspend Current. The FT232R has a low 15mA operating supply current and a very low USB suspend current of approximately 70μA. (Note that during suspend mode, the current drawn by any customised cable application which uses the USB supply, should not exceed 2.5mA to remain USB compliant) Low USB Bandwidth Consumption. The USB interface of the FT232R, and therefore the USB-RS232 cables has been designed to use as little as possible of the total USB bandwidth available from the USB host controller. UART Pin Signal Inversion. The sense of each of the UART signals can be individually inverted by configuring options in the internal EEPROM. For example CTS# (active low) can be changed to CTS (active high), or TXD can be changed to TXD#. FTDIChip-ID™. The FT232R includes the new FTDIChip-ID™ security dongle feature. This FTDIChip-ID™ feature allows a unique number to be burnt into each cable during manufacture. This number cannot be reprogrammed. This number is only readable over USB can be used to form the basis of a security dongle which can be used to protect any customer application software being copied. This allows the possibility of using the USB-RS232 cables as a dongle for software licensing. Further to this, a renewable license scheme can be implemented based on the FTDIChip-ID™ number when encrypted with other information. This encrypted number can be stored in the user area of the FT232R internal EEPROM, and can be decrypted, then compared with the protected FTDIChip-ID™ to verify that a license is valid. Web based applications can be used to maintain product licensing this way. An application note, AN232R-02, available from FTDI website (www.ftdichip.com) describes this feature. Improved EMI Performance. The USB-RS232 cables are FCC and CE certified. Extended Operating Temperature Range - The USB-RS232 cables are capable of operating over an extended temperature range of -40º to +85º C thus allowing them to be used in automotive or industrial applications. Copyright © 2010 Future Technology Devices International Limited 6 Document Reference No.: FT_000077 USB TO RS232 SERIAL CONVERTER RANGE OF CABLES Datasheet Version 1.3 Clearance No.: FTDI# 51 5 USB-RS232-WE-LLLL-CU-PWR The USB-RS232-WE cable is un-terminated; it has bare and tinned wires. The LLLL specifies the length of the cable in cm. The CU specifies the colour of the cable and the colour of the USB connector. The cable can be either Black or transparent. The USB connector can either be black or transparent. For simplicity, the LLLL and CU have been dropped from the following descriptions. 5.1 USB-RS232-WE-PWR Connections and Mechanical Details The following Figure 5.1 shows the cable signals and the wire colours for the signals on the USB-RS232WE cable. OV or +3.3V or +5V (default is 0V) GND 1 1 BLACK CTS# 2 2 BROWN POWER* 3 CABLE 1.8m 3 RED ORANGE TXD 4 4 RXD 5 5 YELLOW RTS# 6 6 GREEN POWER* - default is GND, but can be manufactured to provide +3.3V or +5V Figure 5.1 USB-RS232-WE Connections Figure 5.2 USB-RS232-WE Mechanical Details (dimensions in mm) Copyright © 2010 Future Technology Devices International Limited 7 Document Reference No.: FT_000077 USB TO RS232 SERIAL CONVERTER RANGE OF CABLES Datasheet Version 1.3 Clearance No.: FTDI# 51 5.2 USB-RS232-WE Cable Signal Descriptions Colour Name Type Description Black GND GND Device ground supply pin. Brown CTS# Input Clear to Send Control input / Handshake signal. Power output. Default is GND, but can be customised to Red POWER Output output +3.3V or +5V. If required, contact FTDI Sales Team ([email protected]) Orange TXD Output Yellow RXD Input Green RTS# Output Transmit Asynchronous Data output. Receive Asynchronous Data input. Request To Send Control Output / Handshake signal. Table 5.1 USB-RS232-WE Cable Signal Descriptions 5.3 USB-RS232-WE Electrical Parameters Parameter Description Minimum Typical Maximum Units Conditions *Default is GND. This figure only applies when cable has been customised to output VCC_5V Output Power Voltage* 4.25 5.0* 5.25 V +5V. The range is dependent on the USB port that the USB-RS232-WE is connected to **Default is GND. This VCC_3.3V Output Power Voltage** 3.2 3.3** 3.4 V figure only applies when cable has been customised to output +3.3V. ***Only applies when POWER output is customised IO Output Power Current*** - 75 mA to +5V or+3.3V Must be less that 2.5mA during suspend. T Operating Temperature Range -40 +85 o C Table 5.2 USB-RS232-WE I/O Operating Parameters Copyright © 2010 Future Technology Devices International Limited 8 Document Reference No.: FT_000077 USB TO RS232 SERIAL CONVERTER RANGE OF CABLES Datasheet Version 1.3 Clearance No.: FTDI# 51 Parameter Vtrans Vrec Description Minimum Typical Maximum Units +/- 5 +/- 6.5 +/- 15 V +25 V Transmitter output voltage swing Receiver input voltage -25 range Conditions Table 5.3 USB-RS232-WE I/O Pin Characteristics Description Conditions Minimum Typical ESD HBM RS-232 Inputs and Outputs ±15 kV EN61000-4-2ContactDischarge RS-232 Inputs and Outputs ±8 kV EN61000-4-2AirGapDischarge RS-232 Inputs and Outputs ±15 kV Maximum Table 5.4 USB-RS232-WE ESD Tolerance Copyright © 2010 Future Technology Devices International Limited 9 Document Reference No.: FT_000077 USB TO RS232 SERIAL CONVERTER RANGE OF CABLES Datasheet Version 1.3 Clearance No.: FTDI# 51 6 Cable PCB Circuit Schematic The circuit schematic for the small internal electronic circuit board, utilising the FTDI FT232R, which is encapsulated into the USB connector end of the cable, is shown in Figure 6.1. Customised versions of the cable are also available. Users interested in customised versions of these cables should contact FTDI sales ([email protected]). Charge Pump Caps 2 x 0.1uF VCC VCC_3V3 VCC VCC 4.7uF + 100nF TX LED 19 FB 11 FT232R_PWREN# RX LED 16 10 22 1 USB “A” PLUG 30 1 2 3 10nF FT232R_TXD GND V+ TXD FT232R_RTS 32 FT232RQ 15 2 14 8 USB-DP FT232R_RXD RS232 LEVEL SHIFTER RXD SHUTDOWN# 4 17 20 24 26 RTS# FT232R_CTS 47pF x 2 5 EN# 18 USB-DM 4 VCC 470nF 100nF 21 CTS# V- GND 470nF FT232R_SLEEP# POWER ONLY 1 Resistor is fitted. Default is POWER=GND GND VCC VCC_3V3 Figure 6.1 Circuit Schematic of PCB Used in the USB to RS232 Serial Converter Cable Copyright © 2010 Future Technology Devices International Limited 10 Document Reference No.: FT_000077 USB TO RS232 SERIAL CONVERTER RANGE OF CABLES Datasheet Version 1.3 Clearance No.: FTDI# 51 7 Contact Information Head Office – Glasgow, UK Future Technology Devices International Limited Unit 1, 2 Seaward Place, Centurion Business Park Glasgow G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 E-mail (Sales) [email protected] E-mail (Support) [email protected] E-mail (General Enquiries) [email protected] Web Site URL http://www.ftdichip.com Web Shop URL http://www.ftdichip.com Branch Office – Taipei, Taiwan Future Technology Devices International Limited (Taiwan) 2F, No. 516, Sec. 1, NeiHu Road Taipei 114 Taiwan , R.O.C. Tel: +886 (0) 2 8797 1330 Fax: +886 (0) 2 8751 9737 E-mail (Sales) [email protected] E-mail (Support) [email protected] E-mail (General Enquiries) [email protected] Web Site URL http://www.ftdichip.com Branch Office – Hillsboro, Oregon, USA Future Technology Devices International Limited (USA) 7235 NW Evergreen Parkway, Suite 600 Hillsboro, OR 97123-5803 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 E-Mail (Sales) [email protected] E-Mail (Support) [email protected] Web Site URL http://www.ftdichip.com Branch Office – Shanghai, China Future Technology Devices International Limited (China) Room 408, 317 Xianxia Road, ChangNing District, ShangHai, China Tel: +86 (21) 62351596 Fax: +86(21) 62351595 E-Mail (Sales): [email protected] E-Mail (Support): [email protected] E-Mail (General Enquiries): [email protected] Web Site URL: http://www.ftdichip.com Distributor and Sales Representatives Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s) in your country. Copyright © 2010 Future Technology Devices International Limited 11 Document Reference No.: FT_000077 USB TO RS232 SERIAL CONVERTER RANGE OF CABLES Datasheet Version 1.3 Clearance No.: FTDI# 51 Appendix A - Cable EEPROM Configuration Each USB-RS232 cable is controlled by the FTDI FT232R IC. This FT232R device contains an EEPROM which contains the USB configuration descriptors for that device. When the cable is plugged into a PC or a USB reset is performed, the PC will read these descriptors. The default values stored into the internal EEPROM are defined in Table 0.1 Parameter Value USB Vendor ID (VID) 0403h FTDI default VID (hex) USB Product UD (PID) 6001h FTDI default PID (hex) Serial Number Enabled? Notes Yes A unique serial number is generated and programmed into Serial Number See Note the EEPROM during device final test. Enabling this option will make the device pull down on the Pull down I/O Pins in USB Suspend Disabled is high). Manufacturer Name FTDI Product Description See note Max Bus Power Current Power Source Device Type UART interface lines when the power is shut off (PWREN# USB-RS232-WE 90mA Bus Powered FT232R Returns USB 2.0 device description to the host. USB Version 0200 Note: The device is a USB 2.0 Full Speed device (12Mb/s) as opposed to a USB 2.0 High Speed device (480Mb/s). Remote Wake Up Disabled High Current I/Os Enabled Load VCP Driver Enabled Invert TXD Disabled Signal on this pin becomes TXD# if enable. Invert RXD Disabled Signal on this pin becomes RXD# if enable. Invert RTS# Disabled Signal on this pin becomes RTS if enable. Invert CTS# Disabled Signal on this pin becomes CTS if enable. Enables the high drive level on the UART and CBUS I/O pins. Makes the device load the VCP driver interface for the device. Table 0.1 Default Internal EEPROM Configuration The internal EEPROM in the cable can be re-programmed over USB using the utility program MPROG. MPROG can be downloaded from the www.ftdichip.com. Version 2.8a or later is required for the FT232R chip. Users who do not have their own USB Vendor ID but who would like to use a unique Product ID in their design can apply to FTDI for a free block of unique PIDs. Contact FTDI support for this service. Copyright © 2010 Future Technology Devices International Limited 12 Document Reference No.: FT_000077 USB TO RS232 SERIAL CONVERTER RANGE OF CABLES Datasheet Version 1.3 Clearance No.: FTDI# 51 Appendix B - List of Figures and Tables List of Figures Figure 1.1 Using the USB-RS232 Cable......................................................................................................... 1 Figure 5.1 USB-RS232-WE Connections ....................................................................................................... 7 Figure 5.2 USB-RS232-WE Mechanical Details (dimensions in mm) ......................................................... 7 Figure 6.1 Circuit Schematic of PCB Used in the USB to RS232 Serial Converter Cable ...................... 10 List of Tables Table 1.1 USB-RS232 Cables Descriptions and Part Numbers................................................................... 2 Table 5.1 USB-RS232-WE Cable Signal Descriptions .................................................................................. 8 Table 5.2 USB-RS232-WE I/O Operating Parameters ................................................................................... 8 Table 5.3 USB-RS232-WE I/O Pin Characteristics ........................................................................................ 9 Table 5.4 USB-RS232-WE ESD Tolerance ..................................................................................................... 9 Table 0.1 Default Internal EEPROM Configuration ..................................................................................... 12 Copyright © 2010 Future Technology Devices International Limited 13 Document Reference No.: FT_000077 USB TO RS232 SERIAL CONVERTER RANGE OF CABLES Datasheet Version 1.3 Clearance No.: FTDI# 51 Appendix C - Revision History Version Draft First Draft Aug 2008 Version 1.0 First Release September 12th 2008 Version 1.1 Update to Taiwan address October 1st 2008 Version 1.2 Update to UK and TW address February 11th 2009 Changed front sheet picture. Added additional part numbers Version 1.3 Changed TT to BT (Transparent to Black cable) December 18st 2009 Copyright © 2010 Future Technology Devices International Limited 14