Future Technology Devices International Ltd C232HM USB 2.0 Hi-Speed to MPSSE Cable Datasheet Document Reference No.: FT_000401 Version 1.1 Issue Date: 2012-03-14 Future Technology Devices International Limited (FTDI) Unit 1, 2 Seaward Place, Glasgow G41 1HH, United Kingdom Tel.: +44 (0) 141 429 2777 Fax: + 44 (0) 141 429 2758 E-Mail (Support): [email protected] Web: http://www.ftdichip.com Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. © Copyright 2012 Future Technology Devices International Ltd Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.1 Clearance No.: FTDI# 214 1 Description The USB 2.0 Hi-Speed to MPSSE cable contains a small internal electronic circuit board, utilising the FTDI FT232H, which is encapsulated into the USB connector end of the cable, this handles all the USB signalling and protocols. The cable provides a fast, simple way to connect devices with 3.3 Volt digital interfaces to USB. For full details of the IC, consult the FT232H datasheet, this is available from DS_FT232H. The integrated FT232H device incorporates a command processor called the Multi-Protocol Synchronous Serial Engine (MPSSE). The purpose of the MPSSE command processor is to communicate with devices which use synchronous protocols (such as JTAG, SPI or I2C) in an efficient manner. Full details are available in the MPSSE application note - AN_108. The cable is terminated by ten individual wires with single pole connectors which can be interfaced to a male header. Cable signals are compliant with CMOS logic at 3.3 volts. The FT232H is a single channel USB 2.0 Hi-Speed (480Mb/s) to UART/FIFO IC. It can be configured in a variety of industry standard serial or parallel interfaces, such as MPSSE - JTAG, SPI, I2C. The C232HM MPSSE cable is easily configured into each interface e.g. JTAG, SPI, I2C via the application software. The cable is powered from a USB host port and is USB 2.0 Hi-Speed compatible. The cable is 0.5m long and supports a data transfer up to 30Mbps in MPSSE mode. The C232HM MPSSE cable requires USB device drivers, available free from http://www.ftdichip.com. The D2XX driver is used with application software to directly access the FT232H in the cable though a DLL. This is illustrated in the Figure 1-1 The C232HM MPSSE cable uses the FTDI’s FT232H USB to serial IC device. Connector C232HM D2XX DLL API USB 10 Female pin headers Software application access to USB via D2XX Figure 1-1 Using the C232HM MPSSE Cable Copyright © 2012 Future Technology Devices International Limited 1 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.1 Clearance No.: FTDI# 214 1.1 Available Cables and Part Numbers The following Table 1.1 gives details of the available C232HM MPSSE cables. Part Number Description End Connector Cable details USB to MPSSE cable with +3.3V digital level signals. Maximum C232HM-DDHSL-0 output of 250mA @ 3.3VDC on VCC 10 core, UL2464 24 AWG, Single pole, diam=6.5mm receptacle x 10 (see Note 1) USB to MPSSE cable with +3.3V digital level signals. Maximum C232HM-EDHSL-0 output of 450mA @ 5.0VDC on VCC 10 core, UL2464 24 AWG, Single pole, diam=6.5mm receptacle x 10 (see Note 2) Table 1.1 C232HM MPSSE Cable Descriptions and Part Numbers Note 1: The VCC power output signal (RED wire) is 3.3V. The source of 3.3V is the onboard regulator output, which is switched onto the power output signal. Note 2: The VCC power output signal (RED wire) is 5.0V. The source of 5.0V is the USB VBUS input, which is switched onto the power output signal. FTDI supports customised end connector designs. For more information, please contact your local FTDI sales office (see end of datasheet for contact details). 1.2 Certifications The FTDI C232HM MPSSE cables are fully RoHS, FCC and CE compliant. Copyright © 2012 Future Technology Devices International Limited 2 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.1 Clearance No.: FTDI# 214 Table of Contents 1 2 3 Description ..................................................................................... 1 1.1 Available Cables and Part Numbers ............................................................... 2 1.2 Certifications ................................................................................................. 2 Typical Applications ........................................................................ 4 2.1 Driver Support .............................................................................................. 4 2.2 Features ........................................................................................................ 5 C232HM MPSSE Cable connection and Mechanical Details .............. 6 3.1 C232HM MPSSE Cable Signal Descriptions .................................................... 7 3.2 C232HM MPSSE Cable Signal Descriptions .................................................... 8 3.3 C232HM MPSSE Cable Electrical Parameters ................................................. 9 3.3.1 C232HM-DDHSL-0 Electrical Parameters ..................................................... 9 3.3.2 C232HM-EDHSL-0 Electrical Parameters ....................................................... 9 3.3.1 C232HM-DDHSL-0 and C232HM-EDHSL-0 I/O Characteristics ........................10 4 Cable PCB Circuit Schematic ......................................................... 11 5 Contact Information ..................................................................... 13 Appendix A - Cable EEPROM Configuration ......................................... 15 Appendix B - List of Figures and Tables ............................................. 16 Appendix C – Revision History ........................................................... 17 Copyright © 2012 Future Technology Devices International Limited 3 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.1 Clearance No.: FTDI# 214 2 Typical Applications USB to JTAG interfaces Rapid USB integration into existing USB to SPI interfaces electronic systems 2 USB to I C interfaces Prototyping platform for USB interface on Interfacing MCU / PLD / FPGA based new systems designs to USB USB Instrumentation USB Audio and Low Bandwidth Video data transfer 2.1 Driver Support Royalty free VIRTUAL COM PORT Royalty free D2XX Direct Drivers (VCP) DRIVERS for... (USB Drivers + DLL S/W Interface) Microsoft Windows 2000, Server 2003, XP and Server 2008 Microsoft Windows 2000, Server 2003, XP and Server 2008 Microsoft Windows XP and XP 64-bit Microsoft Windows XP and XP 64-bit Microsoft Windows 7 and Windows 7 64-bit Microsoft Windows 7 and Windows 7 64-bit Microsoft Windows Vista and Vista 64-bit Microsoft Windows Vista and Vista 64-bit Microsoft Windows CE 4.2, 5.0 and 6.0 Microsoft Windows CE 4.2, 5.0 and 6.0 Apple Mac OS-X Linux 2.6.32 or later Linux 2.6.39 or later The drivers listed above are all available to download for free from http://www.ftdichip.com. Various Third-Party Drivers are also available for various other operating systems - see http://www.ftdichip.com/Support/Links.htm for details. Copyright © 2012 Future Technology Devices International Limited 4 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.1 Clearance No.: FTDI# 214 2.2 Features Based on the Single chip USB Hi-Speed FT232H device USB 2.0 Hi-Speed (480Mbits/Second) and Full Speed (12Mbits/Second) compatible Entire USB protocol handled on the chip – No USB-specific firmware programming required USB Type A connector for direct connection to a host or hub Transmit and receive LED drive signals Adjustable receive buffer timeout Support for USB suspend and resume Low operating and USB suspend current Low USB bandwidth consumption UHCI / OHCI / EHCI host controller compatible USB bus powered -40°C to +85°C operating temperature range Fully assisted hardware or X-On / X-Off software handshaking Cable length is 0.5m (19.7 inch) Synchronous Serial (MPSSE) data rates of up to 30Mbps on JTAG, SPI and I2C 1kByte receive and transmit buffers for high data throughput Custom versions also available (subject to Minimum Order Quantity (MOQ)) FTDI’s royalty-free D2XX drivers eliminate the requirement for USB driver development in most cases Copyright © 2012 Future Technology Devices International Limited 5 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.1 Clearance No.: FTDI# 214 3 C232HM MPSSE Cable connection and Mechanical Details The following Figure 3-1 shows the cable signals and the wire colours for these signals on the C232HM MPSSE cable. VCC 1 1 2 TCK 2 TDI 3 3 TD0 4 4 TMS 5 GPIOL0 6 6 GPIOL1 7 7 GPIOL2 8 8 GPIOL3 GND 9 10 5 CABLE 0.5m 9 10 RED ORANGE YELLOW GREEN BROWN GREY PURPLE WHITE BLUE BLACK Figure 3-1 C232HM MPSSE Cable Connections (numbers refer to pad numbers on the PCB) Copyright © 2012 Future Technology Devices International Limited 6 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.1 Clearance No.: FTDI# 214 3.1 C232HM MPSSE Cable Signal Descriptions 42.5 16 Figure 3-2 C232HM MPSSE Cable Mechanical Details (dimensions in mm) Copyright © 2012 Future Technology Devices International Limited 7 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.1 Clearance No.: FTDI# 214 3.2 C232HM MPSSE Cable Signal Descriptions Colour Pin Number Name Type Description Red 1 VCC Output Power Supply Output to target board. Gray 6 GPIOL0 Input/Output General Purpose input/output. Purple 7 GPIOL1 Input/Output General Purpose input/output. White 8 GPIOL2 Input/Output General Purpose input/output. Blue 9 GPIOL3 Input/Output General Purpose input/output. Black 10 GND GND Device ground supply pin. Table 3.1 Common Cable Signal Descriptions Colour Pin Number Name Type Description Orange 2 TCK Output Test Interface Clock Yellow 3 TDI Input Green 4 TDO Output Test Data Output Brown 5 TMS Output Test Mode Select Test Data Input Table 3.2 MPSSE Option JTAG - Signal Descriptions Colour Pin Number Name Type Description Orange 2 SK Output Serial Clock Yellow 3 DO Output Serial data output Green 4 DI Input Serial Data Input Brown 5 CS Output Serial Chip Select Table 3.3 MPSSE Option SPI - Signal Descriptions Colour Pin Number Orange 2 Yellow 3 Green 4 Name Type Description SCL Output Serial Clock SDA Input/Output Serial data signal shorted together to create bidirectional data(both yellow and green wires need to be shorted together) Table 3.4 MPSSE Option I2C - Signal Descriptions Copyright © 2012 Future Technology Devices International Limited 8 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.1 Clearance No.: FTDI# 214 3.3 C232HM MPSSE Cable Electrical Parameters 3.3.1 C232HM-DDHSL-0 Parameter Description Electrical Parameters Minimum Typical Maximum Units VCC Output Power Voltage 3.2 3.3 3.6 V IO Output Power Current - - 200 mA T Operating Temperature Range -40 +85 Conditions o C Table 3.5 C232HM-DDHSL-0 Operating Parameters 3.3.2 C232HM-EDHSL-0 Electrical Parameters Parameter VCC IO T Description Output Power Voltage Supply Current Operating Temperature Range Minimum Typical Maximum Units 4.75 5 5.25 V - - 200 mA -40 +85 Conditions Must be less that 2.5mA during suspend. o C Table 3.6 C232HM-EDHSL-0 Power Supply Output Parameters Copyright © 2012 Future Technology Devices International Limited 9 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.1 Clearance No.: FTDI# 214 3.3.1 C232HM-DDHSL-0 and C232HM-EDHSL-0 I/O Characteristics Parameter Description Minimum Typical Voh Output Voltage High 2.40 3.14 Maximum Units Conditions Ioh = +/-2mA V I/O Drive strength* = 4mA 3.20 V 3.22 V 3.22 V I/O Drive strength* = 8mA I/O Drive strength* = 12mA I/O Drive strength* = 16mA Iol = +/-2mA Vol Output Voltage Low 0.18 0.40 V I/O Drive strength* = 4mA Vil Vih Vt Vt- Vt+ Rpu Rpd Iin Ioz 0.12 V 0.08 V 0.07 V Input low Switching - Input High Switching Threshold Schmitt trigger negative going threshold voltage 0.80 resistance Input Leakage Current Tri-state output leakage current 16mA - V LVTTL 1.50 V LVTTL - V 1.60 2.00 V 40 75 190 KΩ Vin = 0 40 75 190 KΩ Vin =VCCIO 15 45 85 μA Vin = 0 μA Vin = 5.5V or 0 going threshold voltage Input pull-down I/O Drive strength* = 1.10 Schmitt trigger positive Input pull-up resistance 12mA LVTTL 2.00 Switching Threshold I/O Drive strength* = V Threshold 0.80 I/O Drive strength* = 8mA ±10 Table 3.7 C232HD-DDHSP-0 and C232HD-EDHSP-0 I/O Pin Characteristics * The I/O drive strength and slow slew-rate are configurable in the EEPROM. The I/O pins are +3.3v cells, which are +5V tolerant Copyright © 2012 Future Technology Devices International Limited 10 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.1 Clearance No.: FTDI# 214 4 Cable PCB Circuit Schematic The circuit schematics for the small internal electronic circuit board, utilising the FTDI FT232H, which is encapsulated into the USB connector end of the cable, are shown in Figure 4.1 Circuit Schematic of C232HM-DDHSL-0 and Figure 4.2 - Circuit Schematic of PCB - C232HM-EDHSL-0. Customised versions of these cables are also available. Users interested in customised versions of these cables should contact FTDI sales ([email protected]). Figure 4.1 Circuit Schematic of C232HM-DDHSL-0 Copyright © 2012 Future Technology Devices International Limited 11 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.1 Clearance No.: FTDI# 214 Figure 4.2 - Circuit Schematic of PCB - C232HM-EDHSL-0 Copyright © 2012 Future Technology Devices International Limited 12 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.1 Clearance No.: FTDI# 214 5 Contact Information Head Office – Glasgow, UK Future Technology Devices International Limited Unit 1, 2 Seaward Place, Centurion Business Park Glasgow, G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) Web Site URL Web Shop URL [email protected] [email protected] [email protected] http://www.ftdichip.com http://www.ftdichip.com Branch Office – Taipei, Taiwan Future Technology Devices International Limited (Taiwan) 2F, No. 516, Sec. 1, NeiHu Road Taipei 114 Taiwan , R.O.C. Tel: +886 (0) 2 8797 1330 Fax: +886 (0) 2 8751 9737 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) Web Site URL [email protected] [email protected] [email protected] http://www.ftdichip.com Branch Office – Hillsboro, Oregon, USA Future Technology Devices International Limited (USA) 7235 NW Evergreen Parkway, Suite 600 Hillsboro, OR 97123-5803 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 E-Mail (Sales) E-mail (Support) E-mail (General Enquiries) Web Site URL [email protected] [email protected] [email protected] http://www.ftdichip.com Branch Office – ShangHai, China Future Technology Devices International Limited (China) Room 408, 317 Xianxia Road, ChangNing District, ShangHai, P.R. China Tel: +86 (21) 62351596 Fax: +86 (21) 62351595 E-Mail (Sales) E-mail (Support) E-Mail (General Enquiries) Web Site URL [email protected] [email protected] [email protected] http://www.ftdichip.com Distributor and Sales Representatives Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s) in your country. Copyright © 2012 Future Technology Devices International Limited 13 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.1 Clearance No.: FTDI# 214 System and equipment manufacturers and designers are responsible to ensure that their systems, and any Future Technology Devices International Ltd (FTDI) devices incorporated in their systems, meet all applicable safety, regulatory and system-level performance requirements. All application-related information in this document (including application descriptions, suggested FTDI devices and other materials) is provided for reference only. While FTDI has taken care to assure it is accurate, this information is subject to customer confirmation, and FTDI disclaims all liability for system designs and for any applications assistance provided by FTDI. Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. This document is subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Neither the whole nor any part of the information contained in, or the product described in this document, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH, United Kingdom. Scotland Registered Company Number: SC136640. Copyright © 2012 Future Technology Devices International Limited 14 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.1 Clearance No.: FTDI# 214 Appendix A - Cable EEPROM Configuration Each C232HM MPSSE cable is controlled by the FTDI FT232H IC. This FT232H device contains an EEPROM which contains the USB configuration descriptors for that device. When the cable is plugged into a PC or a USB reset is performed, the PC will read these descriptors. The default values stored into the internal EEPROM are defined in the following table Parameter Value USB Vendor ID (VID) 0403h FTDI default VID (hex) USB Product UD (PID) 6014h FTDI default PID (hex) Serial Number Enabled? Notes Yes A unique serial number is generated and programmed into Serial Number See Note Manufacturer Name the EEPROM during device final test. FTDI Product description depends on the cable. The following lists a the Product descriptions for each different cable. Product Description See note C232HM-VSW3V3 C232HM-VSW5V0 Max Bus Power Current Power Source 500mA Includes power available from the cable plus power required for the FT232H Bus Powered Device Type FT232H USB Version 0200 Returns USB 2.0 device description to the host. Note: The device is a USB 2.0 Hi-Speed device (480Mb/s). Remote Wake Up Disabled 500uA suspend limit when in this state High Current I/Os Enabled Enables the high drive level on the CBUS I/O pins. Invert TXD Disabled Signal on this pin becomes TXD# if enable. Invert RXD Disabled Signal on this pin becomes RXD# if enable. Invert RTS# Disabled Signal on this pin becomes RTS if enable. Invert CTS# Disabled Signal on this pin becomes CTS if enable. Default Internal EEPROM Configuration The internal EEPROM in the cable can be re-programmed over USB using the utility program FT_PROG. Both can be downloaded from www.ftdichip.com. Copyright © 2012 Future Technology Devices International Limited 15 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.1 Clearance No.: FTDI# 214 Appendix B - List of Figures and Tables List of Figures Figure 1-1 Using the C232HM MPSSE Cable ................................................................ 1 Figure 3-1 C232HM MPSSE Cable Connections (numbers refer to pad numbers on the PCB) ........................................................................................................................... 6 Figure 3-2 C232HM MPSSE Cable Mechanical Details (dimensions in mm) ................ 7 Figure 4.1 Circuit Schematic of C232HM-DDHSL-0.................................................... 11 Figure 4.2 - Circuit Schematic of PCB - C232HM-EDHSL-0 ........................................ 12 List of Tables Table 1.1 C232HM MPSSE Cable Descriptions and Part Numbers ................................ 2 Table 3.1 Common Cable Signal Descriptions ............................................................. 8 Table 3.2 MPSSE Option JTAG - Signal Descriptions ................................................... 8 Table 3.3 MPSSE Option SPI - Signal Descriptions ...................................................... 8 Table 3.4 MPSSE Option I2C - Signal Descriptions ...................................................... 8 Table 3.5 C232HM-DDHSL-0 Operating Parameters .................................................. 9 Table 3.6 C232HM-EDHSL-0 Power Supply Output Parameters ................................. 9 Table 3.7 C232HD-DDHSP-0 and C232HD-EDHSP-0 I/O Pin Characteristics ............. 10 Copyright © 2012 Future Technology Devices International Limited 16 Document Reference No.: FT_000401 USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet Version 1.1 Clearance No.: FTDI# 214 Appendix C – Revision History Version 1.0 First Release 21st July 2011 Version 1.1 Updated schematic to give correct the 14th March 2012 correct part number for the fuse, and correct current limits in Table1.1. Updated section 1.1, Linux Version Copyright © 2012 Future Technology Devices International Limited 17