UMFT60x FIFO TO USB 3.0 Bridge Evaluation Board Version 1.0 Document Reference No.:FT_001191 Clearance No.: FTDI#457 Future Technology Devices International Ltd UMFT60x (FIFO TO USB 3.0 Bridge Evaluation Board) The UMFT60xx is an evaluation/development module with either FMC(LPC)/HSMC connectors for interfacing FTDI’s FT60x USB 3.0 Superspeed IC with external hardware. The UMFT60xx allows for bridging a FIFO bus to a USB3.0 host and evaluating the functionality of the FT60x. The UMFT60xx module has the following features: Supports USB 3.0 Super Speed (5Gbps)/USB 2.0 High Speed (480Mbps)/USB 2.0 Full Speed (12Mbps) transfer 4 IN channels and 4 OUT channels on FIFO bus connectivity Supports multi voltage I/O: 1.8V, 2.5V and 3.3V High speed connector for FIFO bus : FMC(Field Programmable Mezzanine Card) or HSMC (High Speed Mezzanine Card) module FMC connector is compatible with most Xilinx FPGA reference design boards The UMFT60xx supports 2 parallel slave FIFO bus protocols (Multi-Channel FIFO / 245 Synchronous FIFO) with a data “burst” rate of up to 400MB/s. For a full list of the FT60x’s features refer to the FT60x datasheet. HSMC is compatible with most Altera FPGA reference design boards Multi powered options: external DC powered, BUS powered, FMC/HSMC powered Hardware Reset and Remote Wake Up Micro-USB3.0 receptacle As a daughter card, the UMFT60xx must work with a FIFO master board which has either a FMC or HSMC connector. There are 4 models which provide different FIFO bus interfaces and data bit widths. The modules are designed such that they can plug into most FPGA development platforms supplied by vendors such as Xilinx or Altera. Refer to options. Ordering Information for Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology Devices International Ltd will not accept any claim for damages howsoever arising as a result of u se or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. Th is document provides preliminary information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH United Kingdom. Scotland Registered Company Number: SC136640 UMFT60x FIFO TO USB 3.0 Bridge Evaluation Board Version 1.0 Document Reference No.: FT_001191 Clearance No.: FTDI#457 1 Ordering Information Part No. Description UMFT600A 16 Bit FIFO bus, HSMC connector UMFT601A 32 Bit FIFO bus, HSMC connector UMFT600X 16 Bit FIFO bus, FMC (Low Pin Count)connector UMFT601X 32 Bit FIFO bus, FMC(Low Pin Count) connector Table 1.1 UMFT60xx Ordering Information Copyright © 2015 Future Technology Devices International Limited 1 UMFT60x FIFO TO USB 3.0 Bridge Evaluation Board Version 1.0 Document Reference No.: FT_001191 Clearance No.: FTDI#457 Table of Contents 1 Ordering Information ...............................................................1 2 Hardware Description ...............................................................3 2.1 Physical Description .....................................................................5 2.1.1 2.2 Dimensions .................................................................................................... 5 Connectors, Jumpers and Push Buttons .......................................7 2.2.1 CN1 - Micro USB3.0 Receptacle ........................................................................ 7 2.2.2 CN2 – POWER JACK 2.1MM .............................................................................. 7 2.2.3 JP1 – External/VBUS Powered Selection ............................................................ 7 2.2.4 JP2 – VCC33 Selection .................................................................................... 8 2.2.5 JP3, JP6– VCCIO Selection ............................................................................... 8 2.2.6 JP4, JP5 –FIFO mode selection and GPIO pin out ................................................ 8 2.2.7 SW1, SW2 – Push Buttons for Reset and Remote Wake Up .................................. 8 2.2.8 CN4 – FMC / HSMC FIFO bus interface connector. ............................................... 9 3 Board Schematics ...................................................................13 4 Hardware Setup Guide ............................................................ 18 5 4.1 Power Configuration .................................................................. 18 4.2 Jumpers Default Position ........................................................... 18 4.3 Power Consumption ................................................................... 19 Contact Information ............................................................... 20 Appendix A – References ............................................................. 21 Document References ........................................................................ 21 Acronyms and Abbreviations .............................................................. 21 Appendix B – List of Tables & Figures .......................................... 22 List of Tables ...................................................................................... 22 List of Figures .................................................................................... 22 Appendix C – Revision History ..................................................... 23 Copyright © 2015 Future Technology Devices International Limited 2 UMFT60x FIFO TO USB 3.0 Bridge Evaluation Board Version 1.0 Document Reference No.: FT_001191 2 Clearance No.: FTDI#457 Hardware Description Figure 2-1 UMFT600A Module Top and Bottom View Figure 2-2 UMFT601A Module Top and Bottom View Figure 2-3 UMFT600X Module Top and Bottom View Copyright © 2015 Future Technology Devices International Limited 3 UMFT60x FIFO TO USB 3.0 Bridge Evaluation Board Version 1.0 Document Reference No.: FT_001191 Clearance No.: FTDI#457 Figure 2-4 UMFT601X Module Top and Bottom View The main functions of the UMFT60xx module are as follows: Provides Multi-channel FIFO mode and 245 Synchronous FIFO mode Protocols, configured by GPIOs. Configurable FIFO clock: 66.67MHz and 100MHz (100MHz only for 2.5V or 3.3V VCCIO), default clock is 100MHz. High speed FIFO bus interface: FMC (Low Pin Count) and HSMC optional. See Ordering Information. Jumpers selection allowing powered options: VBUS-powered, External DC-powered, FIFO master board-powered. Multi voltage VCCIO option:1.8V, 2.5V, 3.3V. Configurable GPIOs. Hardware reset and remote wake up support. Available with 16bit and 32bit wide FIFO bus. Copyright © 2015 Future Technology Devices International Limited 4 UMFT60x FIFO TO USB 3.0 Bridge Evaluation Board Version 1.0 Document Reference No.: FT_001191 Clearance No.: FTDI#457 2.1 Physical Description The UMFT600A/UMFT601A and UMFT600X/UMFT601X modules dimensions are illustrated in Figure 2.5 to Figure 2.8. 2.1.1 Dimensions 71.12 3.81 5.715 60.0 50.485 3.78 78.7 Figure 2-5 UMFT600A/UMFT601A Dimensions (Top view) 11.2 11.2 1.6 1.6 4.5 11.2 1.6 Figure 2-6 UMFT600A/UMFT601A Dimensions (Side view) ±0.10mm Tolerance All dimensions are in mm Copyright © 2015 Future Technology Devices International Limited 5 UMFT60x FIFO TO USB 3.0 Bridge Evaluation Board Version 1.0 Document Reference No.: FT_001191 Clearance No.: FTDI#457 63.56 3.515 11.33 60.0 70.0 Figure 2-7 UMFT600X/UMFT601X Dimensions (Top view) 11.2 1.6 6.3 Figure 2-8 UMFT600X/UMFT601X Dimensions (Side view) ±0.10mm Tolerance All dimensions are in mm Copyright © 2015 Future Technology Devices International Limited 6 UMFT60x FIFO TO USB 3.0 Bridge Evaluation Board Version 1.0 Document Reference No.: FT_001191 Clearance No.: FTDI#457 2.2 Connectors, Jumpers and Push Buttons Connectors, jumpers and push buttons are described in the following sections. 2.2.1 CN1 - Micro USB3.0 Receptacle Pin No. Name Type Description 1 VBUS P 5V DC power supply 2 D- IO USB D- line 3 D+ IO USB D+ line 4 ID IO OTG identification(N.C.) 5 GND P Ground 6 SSTX- O Super Speed USB transmitter differential pair (-) 7 SSTX+ O Super Speed USB transmitter differential pair(+) 8 GND P Ground 9 SSRX- I Super Speed USB receiver differential pair (-) 10 SSRX+ I Super Speed USB receiver differential pair (+) Table 2.1 CN1 - Micro USB3.0 Pin-out 2.2.2 CN2 – POWER JACK 2.1MM Optional external DC 5V input. Pin No. Name Type Description 1 5V P 5V power supply 2 GND P Ground 3 GND P Ground Table 2.2 CN2 – POWER JACK 2.1MM 2.2.3 JP1 – External/VBUS Powered Selection Select whether the module power is supplied by an external DC 5V or VBUS. Note this setting must be chosen in conjunction with the JP2 setting. Default is open. [Note] Jumper position Description Short pin 1-2 Select VBUS Power Short pin 2-3 Select external DV 5V Table 2.3 JP1 – 5V input Options Copyright © 2015 Future Technology Devices International Limited 7 UMFT60x FIFO TO USB 3.0 Bridge Evaluation Board Version 1.0 Document Reference No.: FT_001191 2.2.4 Clearance No.: FTDI#457 JP2 – VCC33 Selection Select whether the module main power is supplied by DC5V or the FIFO master board DC3.3V.[Note] Jumper position Description Short pin 1-2 Select powered by external DV5V or VBUS Short pin 2-3 Select powered by FIFO master Board(default) Table 2.4 JP3 – VCC33 Option 2.2.5 JP3, JP6– VCCIO Selection Select the IO voltage level. [Note] Jumper position Description JP3 JP6 Short pin 1-2 Open VCCIO=2.5V(default) Short pin 2-3 Open VCCIO=1.8V Open Short VCCIO=3.3V Table 2.5 JP3 – VCCIO Option 2.2.6 JP4, JP5 –FIFO mode selection and GPIO pin out Select Multi-channel FIFO mode or 245 Synchronous FIFO mode. JP4 pin2 is GPIO_0 pin out and JP5 pin2 is GPIO_1 pin out. Jumper position GPIO valid FIFO Mode JP5 JP4 Channel No. GPIO_0 GPIO_1 (JP4 pin2) (JP5 pin2) 1-2(or open) 1-2(or open) Multi-Channel FIFO 4 Yes Yes 1-2(or open) 2-3 Multi-Channel FIFO 2 Yes No 2-3 1-2(or open) Multi-Channel FIFO 1 No Yes 2-3 2-3 245 Synchronous FIFO 1 No No Table 2.6 JP4, JP5 – Configurations Note: Please refer to section 4 Hardware setup guide for more details power configuration options and jumpers positions. 2.2.7 SW1, SW2 – Push Buttons for Reset and Remote Wake Up SW1 – Reset, module hardware reset, mapped to FMC/HSMC connector, can be used for FIFO master reset. Drive low when press down. Copyright © 2015 Future Technology Devices International Limited 8 UMFT60x FIFO TO USB 3.0 Bridge Evaluation Board Version 1.0 Document Reference No.: FT_001191 Clearance No.: FTDI#457 SW2 – Remote Wake Up, drive low when press down. 2.2.8 2.2.8.1 CN4 – FMC / HSMC FIFO bus interface connector. FMC connector configurations-UMFT600X/UMFT601X Module FMC Pin#/Name UMFT600X UMFT601X U1: FT600 Pin#/Name U1: FT601 Pin#/Name C14/LA10_P 11 /Wake up_N (Optional, default: OPEN) 16 /Wake up_N (Optional, default: OPEN) C15/LA10_N 10 /RESET_N 15 /RESET_N C18/LA14_P 12 /GPIO_0(Optional, default: OPEN) 17 /GPIO_0(Optional, default: OPEN) C19/LA14_N 13 /GPIO_1(Optional, default: OPEN) 18 /GPIO_1(Optional, default: OPEN) C22/LA18_P_CC 43 /D_CLK (FIFO bus clock,FT600 output) 68 /D_CLK (FIFO bus clock,FT601 output) C26/LA27_P N.C. 62 /DATA18 C27_LA27_N N.C. 60 /DATA16 D14/LA09_P N.C. 8 /BE_N_3 D15/LA09_N N.C. 7 /BE_N_2 D20/LA17_P_CC N.C. 76 /DATA31 D21/LA17_N_CC N.C. 75 /DATA30 D23/LA23_P N.C. 70 /DATA25 D24/LA23_N N.C. 69 /DATA24 D26/LA26_P N.C. 63 /DATA19 D27/LA26_N N.C. 61 /DATA17 G6/LA00_P_CC N.C. 13 /OE_N G7/LA00_N_CC N.C. 12 /RD_N G12/LA08_P N.C. 11 /WR_N G13/LA08_N N.C. 10 /SIWU_N G21/LA20_P 9 /OE_N 74 /DATA29 G22/LA20_N 8 /RD_N 73 /DATA28 G24/LA22_P 7 /WR_N 67 /DATA23 G25/_LA22_N 6 /SIWU_N 65 /DATA21 G27/LA25_P 56 /DATA15 57 /DATA15 G28/LA25_N 54 /DATA13 55 /DATA13 Copyright © 2015 Future Technology Devices International Limited 9 UMFT60x FIFO TO USB 3.0 Bridge Evaluation Board Version 1.0 Document Reference No.: FT_001191 FMC Pin#/Name Clearance No.: FTDI#457 UMFT600X UMFT601X U1: FT600 Pin#/Name U1: FT601 Pin#/Name G30/LA29_P 48 /DATA11 53 /DATA11 G31/LA29_N 46 /DATA9 51 /DATA9 G33/LA31_P 42 /DATA7 47 /DATA7 G34/LA31_N 40 /DATA5 45 /DATA5 G36/LA33_P 36 /DATA3 43 /DATA3 G37/LA33_N 34 /DATA1 41 /DATA1 H13/LA07_P N.C. 9 /RXF_N H14/LA07_N N.C. 8 /TXE_N H19/LA15_P N.C. 5 /BE_N_1 H20/LA15_N N.C. 4 /BE_N_0 H22/LA19_P 5 /RXF_N 72 /DATA27 H23/LA19_N 4 /TXE_N 71 /DATA26 H25/LA21_P 3 /BE_N_1 66 /DATA22 H26/LA21_N 2 /BE_N_0 64 /DATA20 H28/LA24_P 55 /DATA14 56 /DATA14 H29/LA24_N 53 /DATA12 54 /DATA12 H31/LA28_P 47 /DATA10 52 /DATA10 H32/LA28_N 45 /DATA8 50 /DATA8 H34/LA30_P 41 /DATA6 46 /DATA6 H35/LA30_N 39 /DATA4 44 /DATA4 H37/LA32_P 35 /DATA2 42 /DATA2 H38/LA32_N 33 /DATA0 40 /DATA0 Table 2.7 CN4 – FMC connector configuration for FIFO bus 2.2.8.2 CN4 – HSMC connector configurations-UMFT600A/UMFT601A Module HSMC Pin#/Name 40 /CLKIN0 UMFT600A UMFT601A U1: FT600 Pin#/Name U1: FT601 Pin#/Name 43 /D_CLK (FIFO bus clock,FT600 output) 68 /D_CLK (FIFO bus clock,FT601 output) Copyright © 2015 Future Technology Devices International Limited 10 UMFT60x FIFO TO USB 3.0 Bridge Evaluation Board Version 1.0 Document Reference No.: FT_001191 HSMC Pin#/Name Clearance No.: FTDI#457 UMFT600A UMFT601A U1: FT600 Pin#/Name U1: FT601 Pin#/Name 41 /D0 33 /DATA0 40 /DATA0 42 /D1 45 /DATA8 60 /DATA16 43 /D2 34 /DATA1 41 /DATA1 44 /D3 46 /DATA9 61 /DATA17 47 /D4 35 /DATA2 42 /DATA2 48 /D5 47 /DATA10 62 /DATA18 49 /D6 36 /DATA3 43 /DATA3 50 /D7 48 /DATA11 63 /DATA19 53 /D8 39 /DATA4 44 /DATA4 54 /D9 53 /DATA12 64 /DATA20 55 /D10 40 /DATA5 45 /DATA5 56 /D11 54 /DATA13 65 /DATA21 59 /D12 41 /DATA6 46 /DATA6 60 /D13 55 /DATA14 66 /DATA22 61 /D14 42 /DATA7 47 /DATA7 62 /D15 56 /DATA15 67 /DATA23 65 /D16 N.C. 50 /DATA8 66 /D17 2 /BE_N_0 69 /DATA24 67 /D18 N.C. 51 /DATA9 68 /D19 3 /BE_N_1 70 /DATA25 71 /D20 N.C. 52 /DATA10 72 /D21 4 /TXE_N 71 /DATA26 73 /D22 N.C. 53 /DATA11 74 /D23 5 /RXF_N 72 /DATA27 77 /D24 13 /GPIO_1(Optional, default: OPEN) 54 /DATA12 78 /D25 6 /SIWU_N 73 /DATA28 79 /D26 12 /GPIO_0(Optional, default: OPEN) 55 /DATA13 80 /D27 7 /WR_N 74 /DATA29 Copyright © 2015 Future Technology Devices International Limited 11 UMFT60x FIFO TO USB 3.0 Bridge Evaluation Board Version 1.0 Document Reference No.: FT_001191 HSMC Pin#/Name Clearance No.: FTDI#457 UMFT600A UMFT601A U1: FT600 Pin#/Name U1: FT601 Pin#/Name 83 /D28 10 /RESET_N 56 /DATA14 84 /D29 8 /RD_N 75 /DATA30 85 /D30 11 /Wake up_N (Optional, default: OPEN) 57 /DATA15 86 /D31 9 /OE_N 76 /DATA31 101 /D40 N.C. 4 /BE_N_0 102 /D41 N.C. 8 /TXE_N 103 /D42 N.C. 5 /BE_N_1 104 /D43 N.C. 9 /RXF_N 107 /D44 N.C. 7 /BE_N_2 108 /D45 N.C. 10 /SIWU_N 109 /D46 N.C. 8 /BE_N_3 110 /D47 N.C. 11 /WR_N 113 /D48 N.C. 18 /GPIO_1(Optional, default: OPEN) 114 /D49 N.C. 12 /RD_N 115 /D50 N.C. 17 /GPIO_0(Optional, default: OPEN) 116 /D51 N.C. 13 /OE_N 119 /D52 N.C. 15 /RESET_N 121 /D54 N.C. 16 /Wake up_N (Optional, default: OPEN) Table 2.8 CN4 – HSMC connector configuration for FIFO bus Note: Refer to the FT600/FT601 device datasheet section 3 for details of the device pin out and signal descriptions. Copyright © 2015 Future Technology Devices International Limited 12 UMFT60x FIFO TO USB 3.0 Bridge Evaluation Board Version 1.0 Document Reference No.: FT_001191 Clearance No.: FTDI#457 3 Board Schematics Figure 3-1 Schematics: Power for UMFT600A/UMFT600X/UMFT601A/UMFT601X Copyright © 2015 Future Technology Devices International Limited 13 UMFT60x FIFO TO USB 3.0 Bridge Evaluation Board Version 1.0 Document Reference No.: FT_001191 Clearance No.: FTDI#457 Figure 3-2 Schematics: USB3.0 Bridge_UMFT600A/UMFT600X Copyright © 2015 Future Technology Devices International Limited 14 UMFT60x FIFO TO USB 3.0 Bridge Evaluation Board Version 1.0 Document Reference No.: FT_001191 Clearance No.: FTDI#457 Figure 3-3 Schematics: USB3.0 Bridge_UMFT601A/UMFT601X Copyright © 2015 Future Technology Devices International Limited 15 UMFT60x FIFO TO USB 3.0 Bridge Evaluation Board Version 1.0 Document Reference No.: FT_001191 Clearance No.: FTDI#457 Figure 3-4 Schematics: HSMC_UMFT600A Figure 3-5 Schematics: HSMC_UMFT601A Copyright © 2015 Future Technology Devices International Limited 16 UMFT60x FIFO TO USB 3.0 Bridge Evaluation Board Version 1.0 Document Reference No.: FT_001191 Clearance No.: FTDI#457 Figure 3-6 Schematics: FMC_UMFT600X Figure 3-7 Schematics: FMC_UMFT601X Copyright © 2015 Future Technology Devices International Limited 17 UMFT60x FIFO TO USB 3.0 Bridge Evaluation Board Version 1.0 Document Reference No.: FT_001191 Clearance No.: FTDI#457 4 Hardware Setup Guide 4.1 Power Configuration There are 3 methods of powering the UMFT60xx module. 1) FIFO master board Power (3.3V)-Connect the UMFT60xx board to the FIFO master board that has the standard configuration FMC (LPC or HPC) or HSMC female connector. This method is the default setting and recommended. 2) USB Power (5V) - Connect USB power by micro-USB3.0 or micro-USB2.0 cable to CN1. 3) DC IN (5V) - Connect DC 5V to CN2. The following table summarizes how to power the UMFT60xx module using the various methods. Power Method CN1 CN2 JP1 JP2 JP3 and JP6 FIFO master board Power(Default and Recommended) - N.C. Open Short pin 2-3 Follow FIFO master IO voltage. USB Power 5V N.C. Short pin1-2 Short pin1-2 DC IN(5V) - 5V Short pin2-3 Short pin1-2 Default: JP3 short pin1-2 VCCIO=2.5V JP6: Open Table 4.1 Board Power Configuration 4.2 Jumpers Default Position Jumper JP1 JP2 JP3 JP4 JP5 JP6 Default Position Open 2-3 1-2 1-2 1-2 Open Table 4.2 Jumpers Default Position Figure 4.1 shows the Jumpers’ locations on the PCB, and they are the same location on all 4 modules. Figure 4-1 Jumpers Locations Copyright © 2015 Future Technology Devices International Limited 18 UMFT60x FIFO TO USB 3.0 Bridge Evaluation Board Version 1.0 Document Reference No.: FT_001191 Clearance No.: FTDI#457 4.3 Power Consumption Parameter Description Minimum Typical Maximum IVCC_1 Units Conditions VCC Operating Supply Current - 190 - mA Function Mode IVCC_2 VCC Operating Supply Current - 7.0 - mA Suspend Mode IVBUS1 VBUS Operating Current - 0.34 - mA DC/HSMC/FMC Powered, Function and Suspend Mode IVBUS2 VBUS Operating Current - 191 - mA VBUS-Powered Powered, Function Mode IVBUS3 VBUS Operating Current - 7.3 - mA VBUS-Powered Powered, Suspend Mode Table 4.3 Power Consumption Copyright © 2015 Future Technology Devices International Limited 19 UMFT60x FIFO TO USB 3.0 Bridge Evaluation Board Version 1.0 Document Reference No.: FT_001191 Clearance No.: FTDI#457 5 Contact Information Head Office – Glasgow, UK Branch Office – Tigard, Oregon, USA Future Technology Devices International Limited Unit 1, 2 Seaward Place, Centurion Business Park Glasgow G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 Future Technology Devices International Limited (USA) 7130 SW Fir Loop Tigard, OR 97223-8160 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) [email protected] [email protected] [email protected] E-Mail (Sales) E-Mail (Support) E-Mail (General Enquiries) [email protected] [email protected] [email protected] Branch Office – Taipei, Taiwan Branch Office – Shanghai, China Future Technology Devices International Limited (Taiwan) 2F, No. 516, Sec. 1, NeiHu Road Taipei 114 Taiwan , R.O.C. Tel: +886 (0) 2 8791 3570 Fax: +886 (0) 2 8791 3576 Future Technology Devices International Limited (China) Room 1103, No. 666 West Huaihai Road, Shanghai, 200052 China Tel: +86 21 62351596 Fax: +86 21 62351595 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) E-mail (Sales) E-mail (Support) E-mail (General Enquiries) [email protected] [email protected] [email protected] [email protected] [email protected] [email protected] Web Site http://ftdichip.com Distributor and Sales Representatives Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s) in your country. System and equipment manufacturers and designers are responsible to ensure that their systems, and any Future Technology Devices International Ltd (FTDI) devices incorporated in their systems, meet all applicable safety, regulatory and system-level performance requirements. All application-related information in this document (including application descriptions, suggested FTDI devices and other materials) is provided for reference only. While FTDI has taken care to assure it is accurate, this information is subject to customer confirmation, and FTDI disclaims all liability for system designs and for any applications assistance provided by FTDI. Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. This document is subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Neither the whole nor any part of the information contained in, or the product described in this document, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH, United Kingdom. Scotland Registered Company Number: SC136640 Copyright © 2015 Future Technology Devices International Limited 20 UMFT60x FIFO TO USB 3.0 Bridge Evaluation Board Version 1.0 Document Reference No.: FT_001191 Clearance No.: FTDI#457 Appendix A – References Document References FT600/FT601 datasheet: DS_FT600Q_FT601Q D3xx Programmers Guide: AN379 Altera FPGA FIFO Master Programming Guide: AN377 Xilinx FPGA FIFO Master Programming Guide: AN376 Acronyms and Abbreviations Terms Description FIFO First In First Out FMC Field Programmable Mezzanine Card HPC High Pin Count HSMC IO High Speed Mezzanine Card Input Output LPC Low Pin Count USB Universal Serial Bus Copyright © 2015 Future Technology Devices International Limited 21 UMFT60x FIFO TO USB 3.0 Bridge Evaluation Board Version 1.0 Document Reference No.: FT_001191 Clearance No.: FTDI#457 Appendix B – List of Tables & Figures List of Tables Table 1.1 UMFT60xx Ordering Information ............................................................................. 1 Table 2.1 CN1 - Micro USB3.0 Pin-out.................................................................................... 7 Table 2.2 CN2 – POWER JACK 2.1MM .................................................................................... 7 Table 2.3 JP1 – 5V input Options .......................................................................................... 7 Table 2.4 JP3 – VCC33 Option .............................................................................................. 8 Table 2.5 JP3 – VCCIO Option............................................................................................... 8 Table 2.6 JP4, JP5 – Configurations ....................................................................................... 8 Table 2.7 CN4 – FMC connector configuration for FIFO bus .................................................... 10 Table 2.8 CN4 – HSMC connector configuration for FIFO bus ................................................. 12 Table 4.1 Board Power Configuration ................................................................................... 18 Table 4.2 Jumpers Default Position ...................................................................................... 18 Table 4.3 Power Consumption ............................................................................................ 19 List of Figures Figure 2-1 UMFT600A Module Top and Bottom View ............................................................... 3 Figure 2-2 UMFT601A Module Top and Bottom View ............................................................... 3 Figure 2-3 UMFT600X Module Top and Bottom View ............................................................... 3 Figure 2-4 UMFT601X Module Top and Bottom View ............................................................... 4 Figure 2-5 UMFT600A/UMFT601A Dimensions (Top view) ........................................................ 5 Figure 2-6 UMFT600A/UMFT601A Dimensions (Side view) ....................................................... 5 Figure 2-7 UMFT600X/UMFT601X Dimensions (Top view) ........................................................ 6 Figure 2-8 UMFT600X/UMFT601X Dimensions (Side view) ....................................................... 6 Figure 3-1 Schematics: Power for UMFT600A/UMFT600X/UMFT601A/UMFT601X ....................... 13 Figure 3-2 Schematics: USB3.0 Bridge_UMFT600A/UMFT600X ................................................ 14 Figure 3-3 Schematics: USB3.0 Bridge_UMFT601A/UMFT601X ................................................ 15 Figure 3-4 Schematics: HSMC_UMFT600A ............................................................................ 16 Figure 3-5 Schematics: HSMC_UMFT601A ............................................................................ 16 Figure 3-6 Schematics: FMC_UMFT600X .............................................................................. 17 Figure 3-7 Schematics: FMC_UMFT601X .............................................................................. 17 Figure 4-1 Jumpers Locations ............................................................................................. 18 Copyright © 2015 Future Technology Devices International Limited 22 UMFT60x FIFO TO USB 3.0 Bridge Evaluation Board Version 1.0 Document Reference No.: FT_001191 Clearance No.: FTDI#457 Appendix C – Revision History Document Title: UMFT60x FIFO TO USB 3.0 Bridge Evaluation Board Document Reference No.: FT_001191 Clearance No.: FTDI#457 Product Page: http://www.ftdichip.com/Products/ICs/FT600.html Document Feedback: Send Feedback Revision 1.0 Changes Initial Release Date 2015-08-25 Copyright © 2015 Future Technology Devices International Limited 23