Document No: 9100-127-1231-99 Issued: November, 2011 Sheet 1 of 2 INSTALLATION INSTRUCTIONS and PARTS LIST SINGLE, DUAL and RETRO FIXTURES MINI L-810 OBSTRUCTION LIGHT ------------------------------------------------------------------------------------------------------------------------------------------Model No RTO 1x07 xxx RTO 1x06 xxx RTO BW07 xxx RTO 1R18 xxx Description 120-240 VAC, FAA 277 VAC 120-277 VAC 12-48 VDC Model No RTO 6x07 xxx RTO 1x08 xxx RTO CR07 xxx RTO 6CR7 xxx 5th digit ... x = color last 3 Description Model No 120-240 VAC, Canada RTO 0x07 xxx 12-48 VDC RTO 2x07 xxx 120-240 VAC, IR RTO CR08 xxx 120-240 VAC, Canada IR digits ... 001 = Single 002 = Dual 004 = Retro Description 120-240 VAC, NonFAA 120-240 VAC, C1D2 12-48 VDC, IR WARNING: DE-ENERGIZE CIRCUIT BEFORE INSTALLING OR WORKING ON FIXTURE The light assembly fixture can be mounted in any position. When mounted 'upright' [as illustrated] the fixture will meet the designed optical specifications for Aircraft Obstruction Warnings. When mounted in any other position, the fixture will not meet the designed optical specifications mentioned and will be considered as a visual signal fixture. SINGLE FIXTURE INSTALLATION STEPS: ► The wire housing 2A has a 1” NPT [3/4" bushing] end to be assembled to conduit [right angle or vertical] Use a 1-1/2” wrench to tighten and attach the wire housing 2A to the conduit Remove reducing bushing 5 if threading into 1” NPT conduit Use 1” NPT plug 4 to close threaded opening not being used ► Feed the supply wires through the conduit and wire housing 2A leaving approx 6” of wire for termination inside the wire housing 2A . ► Electrically connect the supply wires to the light assembly 1 wires Connect the light assembly wire [with voltage label] to the Hot AC line or Positive [+] line Connect the light assembly wire [without label] to the Neutral AC line or Negative [-] line Connect the light assembly green grounding wire to the Ground line ► Tuck the connected wires inside the wire housing 2A . ► Position light assembly 1 over the wire housing 2A and secure using the holding screws 3 . ► Restore power and verify operation DUAL FIXTURE INSTALLATION STEPS: ► The dual housing 2B has a 1” NPT end to be assembled to conduit Remove reducing bushing 5 if threading into 1” NPT conduit Use a 1-1/2” wrench to tighten and attach the dual housing 2B to the conduit Tighten the 1/4 screw 3 to secure the dual wire housing in position ► Feed the supply wires through the conduit and dual housing 2B leaving approx 6” of wire for termination inside the wire housing 2B . ► Electrically connect the supply wires to the light assembly 1 wires same as SINGLE FIXTURE installation ► Tuck the connected wires inside the dual housing 2B . ► Position each light assembly 1 over the dual housing 2B and use the holding screws 3 to secure the light assembly in place ► Restore power and verify operation ------------------------------------------------------------------------------------------------------------------------------------------1501 Route 34 South, Farmingdale, NJ 07727 Tel: [732] 919-3119 Fax: [732] 751-5778 www.dialight.com Document No: 9100-127-1231-99 Issued: November, 2011 Sheet 2 of 2 INSTALLATION INSTRUCTIONS and PARTS LIST SINGLE, DUAL and RETRO FIXTURES MINI L-810 OBSTRUCTION LIGHT ------------------------------------------------------------------------------------------------------------------------------------------RETRO INSTALLATION STEPS: ► Remove existing lens and clamp 6 from existing fixture ► Do not discard clamp 6 since it will be used to secure light assembly 1A . ► Remove and discard all internal components required for use with incandescent bulb ► Leave only the source wires that lead into the existing base 2C . ► Electrically connect the supply wires to the light assembly 1A wires same as SINGLE FIXTURE installation ► Tuck the connected wires inside the existing base 2C . ► Place light assembly 1A on existing base 2C and secure using existing clamp 6 . ► Restore power and verify operation RETRO ONTO 3/4-14 NPT CONDUIT INSTALLATION STEPS: ► Electrically connect the supply wires to the light assembly 1A wires same as SINGLE FIXTURE installation ► Use a 1-1/4” wrench to tighten and attach the light assembly 1A to the conduit ► Restore power and verify operation Please refer to product data sheet for electrical parameters if required Single Housing Fixture Dual Housing Fixture Retro Fixture [Housing] Retro Fixture [Conduit] Patent Pending Item 1 1A 2A 2B 2C Part No. . . 860-1000 860-2000 . PARTS LIST Description Item Light Assembly (w/ Adapter) 3 Light Assembly (w/o Adapter) 4 Single Housing 5 Dual Housing 6 Existing Installed Housing . Part No. . . . . . Description 1/4-20 x ½ Holding Screw 1” Plug 1” to 3/4" Bushing Existing Installed Clamp Rev E ECO No 5156 Drn AV Chk ALV App SM CM JB ------------------------------------------------------------------------------------------------------------------------------------------1501 Route 34 South, Farmingdale, NJ 07727 Tel: [732] 919-3119 Fax: [732] 751-5778 www.dialight.com Date 12-2-11