Microcontrollers and TRIAC-based dimmers

AN392
Application note
Microcontrollers and TRIAC-based dimmers
Introduction
Today, electronics is used in home appliances for applications as widely varying as motor
regulation in a washing machine, control of a vacuum cleaner, dimming of a lamp or heating
in a coffee machine. This evolution has increased pace rapidly because appliances require
enhanced features that are easy to build and modify while electronics-based solutions
become cheaper and more sophisticated.
Within this evolution, microcontrollers (MCU) progressively replace analog controllers and
discrete solutions even in low cost applications. MCUs are more flexible, often need less
components and provide shorter time to market. With an analog IC, the designer is limited to
a fixed function frozen inside the device. With a DIAC control, features like sensor feedback
or enhanced motor drive cannot be easily implemented. With an MCU the designer can
include his own ideas and test them directly using EPROM or one time programmable (OTP)
versions.
The TRIAC is the least expensive power switch to operate directly on the 110/240 V mains.
Thus it is the optimal switch for most of the low-cost power applications operating online.
The logic level or snubberless TRIACs can operate with low gate current and can be directly
triggered by the MCU.
This application note describes two different MCU based applications: a universal motor
drive, and a light dimmer. They all operate with the same user interfaces and almost the
same software and hardware.
April 2009
Doc ID 1863 Rev 2
1/11
www.st.com
Universal motor drive
AN392
1
Universal motor drive
1.1
Power control
The power device is a TRIAC because it is the most economical online switch. In a TRIACbased controller the output power, and, for example, the motor speed, are controlled by the
phase delay of the TRIAC drive. This delay is referred to the zero crossing of the line voltage
which is detected by means of a connection to the mains neutral (Figure 1). Changing
operation from 60 Hz to 50 Hz can be achieved by making simple modifications to the MCU
EPROM/ROM table defining the TRIAC conduction angle versus power level. Automatic
selection of the 50 Hz/ 60 Hz tables can be implemented.
The TRIAC can be directly driven by the MCU. A very short gate current pulse (~ 100 µs)
could be enough to trigger the TRIAC for rms load currents above 2 A. Such pulse control
allows the low voltage MCU power supply consumption to be reduced. The snubberless
TRIAC is driven in quadrants QII and QIII with a 60 mA gate current provided by three I/O
bits of the ST6210 in parallel. This pulse is sufficiently long to ensure the TRIAC is latched at
the end of the pulse. Pulse length can be modified if another TRIAC or motor is used.
Figure 1.
1.2
Mains synchronization
User interfaces
Different user interfaces can be implemented - a touch control, a push button or a
potentiometer. The circuit diagram in Figure 2 show that the three modes are implemented
on the board to let the system designer choose the preferred user interface.
Control action is obtained when the sensor or the button is touched for more than 330 ms. If
the touch duration is between 50 ms and 330 ms, the circuit is switched on or off. A contact
of less than 50 ms causes no action.
2/11
Doc ID 1863 Rev 2
AN392
Universal motor drive
Figure 2.
Motor drive circuit diagram
Fuse
Optional
user interface
+5 V
1
Line
4.7 M
RESET 7
47
BTA16-600CW
-
10 nF
VDD
19
18
17
16
PA0
PA1
PA2
PA3
PB0 15
PB1
Version
13
12
GND
11
PB2
PB4
820-1/2W
1N4148
4.7 M
Push button
1
GND
+5 V
OSCOUT
4
OSCIN
3
Neutral
100 uF/10 V
14
5
NMI
VPP 6
VSS 20
+5 V
5.6 V
GND
ST6210
ST6210
PB3
1M
Load
Touch sensor
4.7 M
Potentiometer
2
8 MHz
22 pF
22 pF
220 nF/400 V
GND
1.3
GND
GND
GND
GND
Circuit components
The MCU chosen (ST6210) includes an 8 bit accumulator, 2 k ROM, 64 bytes RAM, an 8 bit
A/D converter that can be connected to 8 different inputs, 4 I/O lines with 40 mA sink current
capability and a timer. Hysteresis protection is included in series with each I/O pin. The
ST6210 is packaged in DIL or SMD packages. The ports, the timer and interrupt
configurations can be chosen by software, providing high flexibility. The ST6210 has been
designed to operate in very disturbed environments. Each I/O line contains internal diodes
which clamp the input voltage between Vdd and Vss. These diodes are sized to withstand a
continuous current of 1 mA (typ.).
The snubberless TRIAC (BTA 16-600CW) has been specially designed to drive loads which
generate very strong dynamic constraints such as a vacuum cleaner motor. This TRIAC can
be triggered in quadrants QI, QII or QIII with gate and latching current of 35 mA and 80 mA
respectively. In this application it is driven by three I/O lines of the ST6210 in parallel. This
TRIAC has high current switching capability ((dI/dt)c > 8.5 A/ ms and 5.5 A/ms for
BTA10600CW), and high static dv/dt ((dV/dt) > 500 V/ms). So, in this circuit, it can operate
without any snubber.
Total consumption of the board is 3 mA with an 8 MHz oscillator. The board supply comes
from the mains through a simple RCD circuit. The +5 V is referred to anode 1 of the TRIAC
in order to provide the negative gate current necessary to drive the TRIAC in quadrants QII
and QIII. The 5 V supply capacitance is connected as near as possible to the MCU with very
short interconnecting traces to maximize RFI immunity.
The touch sensor is a voltage divider between line and neutral. It works only if the +5 V
supply input of the circuit is connected to the line. This connection to the mains must be
ensured according to local electrical safety rules.
Doc ID 1863 Rev 2
3/11
Universal motor drive
1.4
AN392
Software
All operating features are contained in a 700 byte program. So more than 1 byte of ROM is
available for additional features.
A look-up table relating delay time to the power requirement contains 64 different levels. The
conduction time of the TRIAC can vary from 1.7 ms to 6.7 ms for a 60 Hz application and
from 2 ms to 8 ms to a 50 Hz application. The user can easily adjust the minimum and
maximum power levels because the corresponding delay times are slowly changing at the
top and bottom of the table.
It is recommended that all MCU inputs be filtered so that an input is validated only if it
remains constant for 15 s or more so that passive filter components can be saved. The
mains supply carries disturbances (glitches, telecommand signals, ...) which could disturb
the TRIAC drive. For this reason, a mains voltage zero crossing is only validated if it occurs
during a window of time (1.7 ms each 16.6 ms for 60 Hz operation and 2 ms each 200 ms for
50 Hz operation) selected by the internal timer of the MCU. This block acts as a filter and
again eliminates external components (Figure 3).
This circuit can be used in the following applications:
●
Vacuum regulation in a vacuum cleaner
●
Speed control in a food processor
●
Speed regulation with torque limiting in a drill
●
Unbalance detection in a washing machine
●
Washing machine door opener with remote control
Figure 3.
Major steps of the software
RESET
Initialization
Read version
Line synchronization
Sensor acquisition
Power level requirement
Delay time td1 in timer
Calculation next delay
TRIAC firing
Delay time td2 in timer
Calculation next delay
TRIAC firing
Window for zero
crossing mains
4/11
Doc ID 1863 Rev 2
AN392
2
Light dimmer
Light dimmer
For a light dimmer application, the board can be plugged in series with the line wire like a
mechanical switch. The line synchronization and the auxiliary supply are obtained from the
voltage across the TRIAC (Figure 4).
Figure 4 shows a schematic which can operate either on 110 V or 240 V mains. It uses an
MCU ST6210 and a logic level TRIAC. This circuit drives halogen or incandescent lamps
supplied directly from the mains or through a low voltage transformer. It includes soft start
and protection against transformer saturation and against open load. The user interfaces
are the same as previously presented.
Figure 4.
Light dimmer circuit diagram
Fuse
1
Line
RESET
19
18
17
16
BTA08 -600SW
+5 V
12
GND
11
PB2
PB4
Neutral
820-1/2W
4.7 M
14
4.7 M
Push button
GND
+5 V
Potentiometer
2
8 MHz
22 pF
5.6 V
GND
Touch sensor
10 nF GND
OSCOUT
4
1
+5 V
22k
15
5
NMI
6
VPP
20
VSS
OSCIN
3
200k
4.7 M
7
ST6210
ST6210
PB3
PB5
200k
100k
PB0
PB1
T?
Trans
PA0
PA1
PA2
PA3
Version
13
100k
VDD
100
12 V
Optional
user interface
+5 V
GND
22 pF
GND
GND
GND
1N4148 100 uF/10 V
220 nF/400 V
GND
2.1
Power control
Power is controlled by the phase delay (td) of the TRIAC drive. In the previous design, td is
referred to the zero crossing of the line voltage. To avoid a connection to the mains neutral
as the circuit is in series with the load, the trigger delay is referred to the zero crossing of the
current (see Figure 1). When the TRIAC anode current reaches zero, the mains voltage is
reapplied across the TRIAC. Synchronization is achieved by measuring this voltage. This
voltage is monitored over each half cycle with a network of resistances connected to two I/O
lines of the ST6210. This allows detection of spurious open load and the retriggering of the
TRIAC with multipulse operation if it is not latched after the first gate current pulse.
Doc ID 1863 Rev 2
5/11
Light dimmer
2.2
AN392
Operation with a transformer
Low power halogen spots use low voltage lamps (12 V typ.) usually supplied through a low
voltage transformer. For good application performance, the MCU program should ensure the
following:
2.3
●
At start-up, the delay time between the first gate pulse and the synchronization instant
is greater than 5 ms. This limits transformer coil induction and the risk of saturation with
associated high peak current.
●
The circuit starts on a positive line half cycle and stops on a negative one. Thus it starts
with positive induction and stops after negative induction has been applied. This helps
to minimize the size of the magnetic core material, and the current rating of the TRIAC.
●
The timer is precisely tuned in order to obtain 8.3 ms (for 60 Hz) or 10 ms (for 50 Hz)
delay between two gate pulses. As a result, the TRIAC is driven symmetrically in both
half cycles so that DC voltage content is avoided across the transformer terminals.
Saturation risk is then also reduced here. Otherwise, the voltage across the TRIAC is
monitored to detect a spurious open load condition at the secondary of the transformer.
●
The inrush current at lamp switch-on (halogen or incandescent) is also reduced due to
the soft start feature of the circuit (Figure 6).
TRIAC drive
The TRIAC is directly driven by the MCU. The pulse driving the TRIAC lasts 50 µs. The logic
level TRIAC is driven in quadrants QII and QIII with a gate current of 20 mA provided by two
I/O lines of the ST6210 in parallel. The logic level TRIAC has a maximum specified gate
triggering current of 10 mA at 25 °C.
The TRIAC is multi-pulse driven. Therefore, inductive loads can be driven without the use of
long pulse drives. As a result, the consumption on the +5 V supply can be reduced and the
supply circuit components are downsized. Before supplying the first drive pulse, the TRIAC
voltage is tested. If no voltage is detected, a spurious open load or a supply disconnection is
assumed to have occurred and the circuit is stopped. After the first driving pulse, the TRIAC
voltage is monitored. If the TRIAC is not on, another pulse is sent. The same process can be
repeated up to four times. Then, if the TRIAC is still not on, the circuit is switched off.
2.4
Circuit components
The light dimmer board (Figure 4) is almost the same as the motor drive board (Figure 2).
The major differences concern the point where the voltage is measured and the TRIAC
choice. When the board is dimming a resistive load, an RFI filter should be added to limit the
conducted noise.
In a dimmer, because of the resistive load, dynamic constraints are lower than in a motor
control, so a logic level TRIAC (BTA08-600SW) can be used. It is a sensitive TRIAC
(IGT < 10 mA) which can be triggered in quadrants I, II and III. This TRIAC has high
switching capabilities ((dI/dt)c > 2.98 A/ms, (dV/dt)c > 10 V/ms). Thus it can also operate
without any snubber across it.
The MCU board in Figure 4 is supplied only when the TRIAC is off. A minimum off-time of
the TRIAC (1.7 ms/60 Hz and 2 ms/50 Hz) is necessary to ensure a good VDD level. The
RCD circuit is the same as the one used for the board in Figure 2.
6/11
Doc ID 1863 Rev 2
AN392
2.5
Practical results
Software
The software for a light dimmer can be the same as for motor drive. The major difference
concerns the mains disturbances rejection in order to prevent lamp flickering. The timing is
carried out internally by the MCU timer. The mains period can be calculated internally by the
MCU to detect the mains frequency. But this mains frequency must not be disturbed by
noise coming from the line, as the mains synchronization signal is received every cycle.
3
Practical results
Figure 5 presents the current and voltage in a TRIAC driving a universal motor.
Figure 5.
Universal motor drive: TRIAC current and voltage
TRIAC current IT : 5 A/div
IT
TRIAC voltage VT: 250 V/div
VT
2 ms/div
Doc ID 1863 Rev 2
7/11
Practical results
AN392
Figure 6 presents the soft start operation for an incandescent lamp rated at 150 W, 230 V.
Thanks to the embedded soft start, the peak in-rush current is about 3 times the nominal
current compared with 8 to 10 times otherwise. Therefore, the lamp life time is improved.
Figure 6.
Soft start for 150 W, 230 V incandescent lamp
TRIAC current ITT: 1.0 A/dic
100 ms/div
Voltage across TRIAC VT: 100 V/div
100 ms/div
8/11
Doc ID 1863 Rev 2
AN392
4
Conclusion
Conclusion
Microcontroller units (MCU) are in common use in most areas of home appliances. The
applications described in this Application note show that enhanced appliance circuits can be
designed with ST6210 MCU and a snubberless or logic level TRIAC.
The presented circuits are a universal motor drive, and a light dimmer operating from the
110/240 V mains. The motor drive can be adapted, for instance, to vacuum cleaners, food
processors, drills or washing machines. The light dimmer drives incandescent and halogen
lamps supplied either directly from the mains or through a low voltage transformer.
Those circuits include soft start and protection features. Different user interfaces can be
chosen: touch sensor, push button or potentiometer.
Such features are obtained with only few components: an ST6210 MCU in 20 pin DIL/SMD
package with a logic level or snubberless TRIAC in TO-220 package and some passive
components.
Additional features such as motor speed regulation, torque limitation, vacuum or unbalance
control, IR presence detection, remote control, alarm, homebus interface can also be
implemented.
Doc ID 1863 Rev 2
9/11
Revision history
5
AN392
Revision history
Table 1.
10/11
Document revision history
Date
Revision
Changes
Jan-1998
1
Initial release.
24-Apr-2009
2
Reformatted to current standards. Updated for current products.
Doc ID 1863 Rev 2
AN392
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2009 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
Doc ID 1863 Rev 2
11/11