AS1115

austriamicrosystems AG
is now
ams AG
The technical content of this austriamicrosystems datasheet is still valid.
Contact information:
Headquarters:
ams AG
Tobelbaderstrasse 30
8141 Unterpremstaetten, Austria
Tel: +43 (0) 3136 500 0
e-Mail: [email protected]
Please visit our website at www.ams.com
Datas h eet
A S 111 5
64 L E D s, I ²C I n t er f ac ed L E D Dr i v er w i th K ey sc an
2 Key Features
1 General Description
up to 1MHz I²C-Compatible Interface
Individual LED Segment Control
Readback for 16 Keys plus Interrupt
Open and Shorted LED Error Detection
- Global or Individual Error Detection
Hexadecimal- or BCD-Code for 7-Segment Displays
200nA Low-Power Shutdown Current (typ; data retained)
Digital and Analog Brightness Control
Display Blanked on Power-Up
Drive Common-Cathode LED Displays
Supply Voltage Range: 2.7 to 5.5V
Additionally the AS1115 offers a diagnostic mode for easy and fast
production testing.
Software Reset
Optional External Clock
The AS1115 features a low shutdown current of typically 200nA, and
an operational current of typically 350µA. The number of digits can
be programmed, the devices can be reset by software, and an external clock is also supported.
Package:
The devices include an integrated BCD code-B/HEX decoder, multiplex scan circuitry, segment and display drivers, and a 64-bit memory. Internal memory stores the shift register settings, eliminating the
need for continuous device reprogramming.
am
lc s
on A
te G
nt
st
il
All outputs of the AS1115 can be configured for key readback. Keyswitch status is obtained by polling for up to 64 keys while 16 keys
can be used to trigger an interrupt.
lv
Every segment can be individually addressed and updated separately. Only one external resistor (RSET) is required to set the current. LED brightness can be controlled by analog or digital means.
al
id
The AS1115 is a compact LED driver for 64 single LEDs or 8 digits of
7-segments. The devices can be programmed via an I²C compatible
2-wire interface.
- QSOP-24
- TQFN(4x4)-24
The device is available in a QSOP-24 and the TQFN(4x4)-24 package.
3 Applications
The AS1115 is ideal for seven-segment or dot matrix user interface
displays of set-top boxes, VCRs, DVD-players, washing machines,
micro wave ovens, refrigerators and other white good or personal
electronic applications.
ni
VDD
2.7 to 5.5V
9.53kΩ
ca
Figure 1. AS1115 - Typical Application Diagram
ch
ISET
SDA
Te
SCL
µP
IRQ
SDA
DIG0 to
DIG7
8
SEGA-DP
KEY0-7
8
AS1115
8
SCL
KEYA
IRQ
KEYB
GND
www.austriamicrosystems.com/LED-Driver-ICs/AS1115
Revision 1.08
1 - 25
AS1115
Datasheet - P i n o u t
4 Pinout
Pin Assignments
al
id
3
AS1115
DIG5 5
16 VDD
15 SEGG
14 SEGB
Exposed
Pad
7
8
9
10 11 12
KEYB
ISET
13 SEGF
KEYA
DIG6 6
DIG7
KEYB 12
KEYA 11
DIG7 10
DIG6 9
DIG5 8
SEGDP
17 SEGC
GND
QSOP-24
1
DIG0:DIG7
2-5, 7-10
GND
KEYA
KEYB
6
11
12
ISET
13
SCL
IRQ
SEGA:SEGG,
SEGDP
14
24
SCL
SEGA
am
lc s
on A
te G
nt
st
il
GND 6
SEGD
DIG3 2
TQFN(4x4)-24
22
Description
Serial-Data I/O. Open drain digital I/O I²C data pin.
1, 2, 4, 5, 6, 7, 23, Digit Drive Lines. Eight digit drive lines that sink current from the display common
24
cathode. Keyscan detection optional, but must be polled by the µProzessor.
3
Ground.
8
Keyscan Input. Keyscan lines for key readback. Can be used for self-addressing.
9
Keyscan Input. Keyscan lines for key readback.
Set Segment Current. Connect to VDD or a reference voltage through RSET to set the
10
peak segment current (see Selecting RSET Resistor Value and Using External
Drivers on page 19).
11
Serial-Clock Input. 3.4MHz maximum rate.
21
Interupt Request Output. Open drain pin.
Seven Segment and Decimal Point Drive Lines. 8 seven-segment drives and decimal
12-15, 17-20
point drive that source current to the display.
16
Positive Supply Voltage. Connect to +2.7 to +5.5V supply.
Exposed Pad. This pin also functions as a heat sink. Solder it to a large pad or to the
Exposed Pad
circuit-board ground plane to maximize power dissipation.
ca
Pin Name
SDA
15-18,
20-23
19
ni
VDD
DIG4 7
DIG3 5
DIG2 4
DIG1 3
SDA 1
DIG0 2
Table 1. Pin Descriptions
IRQ
18 SEG E
DIG4 4
Pin Descriptions
SDA
DIG0
24 23 22 21 20 19
DIG2 1
lv
AS1115
DIG1
13 ISET
14 SCL
15 SEGA
16 SEGF
17 SEGB
18 SEGG
19 VDD
20 SEGC
21 SEG E
22 SEGDP
23 SEGD
24 IRQ
Figure 2. Pin Assignments (Top View)
Te
ch
-
www.austriamicrosystems.com/LED-Driver-ICs/AS1115
Revision 1.08
2 - 25
AS1115
Datasheet - A b s o l u t e M a x i m u m R a t i n g s
5 Absolute Maximum Ratings
Stresses beyond those listed in Table 2 may cause permanent damage to the device. These are stress ratings only, and functional operation of
the device at these or any other conditions beyond those indicated in Section 6 Electrical Characteristics on page 4 is not implied.
Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Table 2. Absolute Maximum Ratings
Min
Max
Units
-0.3
7
V
-0.3
7 or
VDD + 0.3
V
DIG0:DIG7 Sink Current
500
mA
SEGA:SEGG, SEGDP Sink Current
100
mA
100
mA
Comments
al
id
Parameter
VDD to GND
All other pins to GND
Input Current (latch-up immunity)
-100
Electrostatic Discharge HBM
Thermal Information
Norm: JEDEC 78
am
lc s
on A
te G
nt
st
il
Electrostatic Discharge
lv
Electrical Parameters
+/- 1
Thermal Resistance ΘJA
kV
Norm: MIL 883 E method 3015
88
°C/W
on PCB, QSOP-24 package
30.5
°C/W
on PCB, TQFN(4x4)-24 package
+150
ºC
+150
ºC
Temperature Ranges and Storage Conditions
Junction Temperature
Storage Temperature Range
-55
Package Body Temperature
Humidity non-condensing
5
ºC
85
%
1
Represents a max. floor life time of unlimited
Te
ch
ni
ca
Moisture Sensitive Level
+260
The reflow peak soldering temperature (body temperature)
specified is in accordance with IPC/JEDEC J-STD020“Moisture/Reflow Sensitivity Classification for NonHermetic Solid State Surface Mount Devices”.
The lead finish for Pb-free leaded packages is matte tin
(100% Sn).
www.austriamicrosystems.com/LED-Driver-ICs/AS1115
Revision 1.08
3 - 25
AS1115
Datasheet - E l e c t r i c a l C h a r a c t e r i s t i c s
6 Electrical Characteristics
VDD = 2.7V to 5.5V, RSET = 9.53kΩ, typ. values @ TAMB = +25ºC, VDD = 5.0V (unless otherwise specified). All limits are guaranteed. The
parameters with min and max values are guaranteed with production tests or SQC (Statistical Quality Control) methods.
Table 3. Electrical Characteristics
TAMB
Parameter
Conditions
Min
Operating Temperature Range
-40
Operating Junction Temperature Range
-40
VDD
Operating Supply Voltage
2.7
IDDSD
Shutdown Supply Current
TJ
All digital inputs at VDD or GND,
TAMB = +25ºC
0.2
RSET = open circuit.
0.35
IDD
Operating Supply Current
fOSC
Display Scan Rate
8 digits scanned
0.48
IDIGIT
Digit Drive Sink Current
VOUT = 0.65V
320
ISEG
Segment Drive Source Current
Unit
+85
°C
+125
°C
5.5
V
2
µA
4
µA
All segments and decimal point on;
ISEG = -40mA.
0.6
mA
335
am
lc s
on A
te G
nt
st
il
ISEG
Max
lv
single digit, TAMB = +85ºC
∆ISEG
Typ
al
id
Symbol
Segment Drive Current Matching
Segment Drive Source Current
VDD = 5.0V, VOUT = (VDD -1V)
-35
0.96
-41
-47
3
Average Current
kHz
mA
mA
%
47
mA
Max
1
Unit
µA
V
V
V
Table 4. Logic Inputs/Outputs Characteristics
Symbol
IIH, IIL
VIH
VIL
VOL(SDA)
Parameter
Input Current SDA, SCL
Logic High Input Voltage SDA, SCL
Logic Low Input Voltage SDA, SCL
SDA Output Low Voltage
VKEYopen
Keyscan Open Input Voltage
VKEYshort
VOL(IRQ)
∆VI
Keyscan Short Input Voltage
Interrupt Output Low Voltage
Hysteresis Voltage
Min
-1
0.7xVDD
Typ
0.3xVDD
0.4
ISINK = 3mA
0.8xVDD
ISINK = 3mA
DIN, CLK, LD/CS
0.7x
VDD
0.05x
VDD
Open Detection Level Threshold
V
V
V
550
0.8x
VDD
pF
0.15x VDD
V
V
Te
ch
ni
Short Detection Level Threshold
0.75x
VDD
0.1x
VDD
V
0.7x VDD
0.4
1
Capacitive Load for each Bus Line
ca
CB
Conditions
VIN = 0V or VDD
www.austriamicrosystems.com/LED-Driver-ICs/AS1115
Revision 1.08
4 - 25
AS1115
Datasheet - E l e c t r i c a l C h a r a c t e r i s t i c s
Table 5. Timing Characteristics (CB = 550pF (max) on each Bus Line)
Parameter
fSCL
SCL Frequency
Bus Free Time Between STOP and START
Conditions
Hold Time for Repeated
START Condition
tHOLDSTART
Min
ns
500
SCL High Period
260
tRISE
ns
ns
260
ns
50
SDA + SCL Rise Time
SDA + SCL Fall Time
tFALL
tSETUPSTOP STOP Condition Setup Time
MHz
260
SCL Low Period
tSETUPDATA
Unit
1
ns
tLOW
tSETUPSTART
Max
500
tHIGH
Setup Time for Repeated
START Condition
Data Setup Time
Typ
260
120
ns
120
ns
ns
50
ns
20
ms
am
lc s
on A
te G
nt
st
il
tSPIKESUP Pulse Width of Spike Suppressed
Key Readback
Debounce Time
ns
lv
tBUF
Conditions
al
id
Symbol
Note: The Min / Max values of the Timing Characteristics are guaranteed by design.
Figure 3. Timing Diagram
SDI
tBUF
tHOLDSTART
tHIGH
tHOLDSTART
tR
tLOW
ca
SCL
tSPIKESUP
tSETUPDATA
tF
tHOLDDATA
Repeated
START
Te
ch
ni
STOP START
tSETUPSTOP
tSETUPSTART
www.austriamicrosystems.com/LED-Driver-ICs/AS1115
Revision 1.08
5 - 25
AS1115
Datasheet - Ty p i c a l O p e r a t i n g C h a r a c t e r i s t i c s
7 Typical Operating Characteristics
RSET = 9.53kΩ, VRset = VDD;
Figure 4. Display Scan Rate vs. Supply Voltage;
Figure 5. Display Scan Rate vs. Temperature;
800
780
Vdd=2.7V
Vdd=5V
Vdd=5.5V
740
720
760
740
lv
fosc (Hz) .
fosc (Hz) .
al
id
Vdd=4V
780
760
720
700
Tamb=-40°C
am
lc s
on A
te G
nt
st
il
700
Tamb=+25°C
Tamb=+85°C
680
2.7
3.1
3.5
3.9
4.3
4.7
5.1
680
-40
5.5
-15
10
Figure 6. Segment Current vs. Temperature;
60
Iseg (mA) .
20
Vseg = 1.7V; Vdd = 2.7V
Vseg = 1.7V; Vdd = 5V
10
Vseg
Vseg
Vseg
Vseg
30
20
10
0
-15
10
35
60
85
0
10
20
Tamb (°C)
30
40
50
60
70
80
90
Rset (kOhm)
Figure 9. Segment Current vs. VDD; VRset = 2.8V
ni
Figure 8. Segment Current vs. Supply Voltage;
50
Vseg
Vseg
Vseg
Vseg
ch
45
40
= 1.7V
= 2V
= 2.3V
= 3.1V
35
Iseg (mA) .
40
Te
Iseg (mA) .
= 4V; Vdd = 5V
= 3V; Vdd = 5V
= 2V; Vdd = 5V
= 1.7V; Vdd = 2.7V
Vseg = 3V; Vdd = 5V
Vseg = 4V; Vdd = 5V
ca
Iseg (mA) .
30
50
85
Figure 7. Segment Current vs. RSET;
40
40
60
60
50
50
0
-40
35
Tamb (°C)
Vdd (V)
30
20
25
20
15
Vseg = 1.7V
10
Vseg = 3V
10
30
Vseg = 4V
5
0
0
2.7
3.1
3.5
3.9
4.3
4.7
5.1
5.5
2.7
Vdd (V)
www.austriamicrosystems.com/LED-Driver-ICs/AS1115
3
3.3
3.6
3.9
4.2
Vdd (V)
Revision 1.08
6 - 25
AS1115
Datasheet - Ty p i c a l O p e r a t i n g C h a r a c t e r i s t i c s
Figure 10. VDIGIT vs. IDIGIT
Figure 11. Input High Level vs. Supply Voltage
0.4
3.5
3
2.5
0.2
1.5
1
= 2.7V
= 3.3V
= 4V
= 5V
= 5.5V
0.5
0
0
0.05
0.1
0.15
0.2
Idig (A)
0.25
0.3
Figure 12. ISEG vs. VSEG; VDD = 5V
50
40
3.5
4.3
4.7
5.1
5.5
Vdd (V)
50
= 10k
= 13k
= 18k
= 30k
= 56k
Rext
Rext
Rext
Rext
Rext
45
40
= 8k2
= 10k
= 13k
= 18k
= 30k
Iseg (mA) .
30
30
25
25
20
20
15
15
10
10
5
5
0
0
2
2.5
3
3.5
4
4.5
5
1
1.5
2
ca
ni
45
ch
40
3
3.5
4
Rext
Rext
Rext
Rext
Rext
Figure 15. ISEG vs. VSEG; VDD = 2.7V
= 6k8
= 8k2
= 10k
= 13k
= 18k
35
30
Te
25
20
50
Rext
Rext
Rext
Rext
Rext
45
40
= 4k7
= 5k6
= 6k8
= 10k
= 13k
35
Iseg (mA) .
Figure 14. ISEG vs. VSEG; VDD = 3.3V
50
2.5
Vseg (V)
Vseg (V)
Iseg (mA) .
3.9
35
35
Iseg (mA) .
3.1
Figure 13. ISEG vs. VSEG; VDD = 4V
Rext
Rext
Rext
Rext
Rext
45
2.7
0.35
am
lc s
on A
te G
nt
st
il
0
lv
Vdd
Vdd
Vdd
Vdd
Vdd
0.1
2
al
id
Vih (V) .
Vdig (V) .
0.3
30
25
20
15
15
10
10
5
5
0
0
1
1.2 1.4 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2
1
Vseg (V)
www.austriamicrosystems.com/LED-Driver-ICs/AS1115
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
Vseg (V)
Revision 1.08
7 - 25
AS1115
Datasheet - D e t a i l e d D e s c r i p t i o n
8 Detailed Description
Block Diagram
al
id
Figure 16. AS1115 - Block Diagram (QSOP-24 Package)
Open/Short
Detection
+
–
RSET
19
+
am
lc s
on A
te G
nt
st
il
VDD
–
Oszillator
VDD
lv
VDD
13
ISET
24
IRQ
8
SEGA-G,
SEGDP
Digital Control
Logic
8
2-5, 7-10
DIG0 to DIG7
(PWM, Debounce,....)
VDD
15-18, 20-23
2
11, 12
KEYA, KEYB
VDD
14
SCL
1
Registers
6
GND
Data - Registers
Control - Registers
Scan - Registers
AS1115
ch
ni
ca
SDA
I²C
Interface
Figure 17. ESD Structure
Te
VDD
valid for the pins:
- IRQ
- SCL
- SDA
- ISET
- SEGA-G, SEGDP
- KEYA, KEYB
www.austriamicrosystems.com/LED-Driver-ICs/AS1115
VDD
valid for the pins:
- DIG0 to DIG7
Revision 1.08
8 - 25
AS1115
Datasheet - D e t a i l e d D e s c r i p t i o n
I²C Interface
The AS1115 supports the I²C serial bus and data transmission protocol in high-speed mode at 3.4MHz. The AS1115 operates as a slave on the
I²C bus. The bus must be controlled by a master device that generates the serial clock (SCL), controls the bus access, and generates the START
and STOP conditions. Connections to the bus are made via the open-drain I/O pins SCL and SDA.
1
0
8
0
0
0
A1
0
9
A0 R/W
1
8
D15 D14 D13 D12 D11 D10
D9
9
D8
lv
Default values at power up: A1 = A0 = 0
al
id
Figure 18. I²C Interface Initialization
am
lc s
on A
te G
nt
st
il
Figure 19. Bus Protocol
MSB
SDI
ACK from
Receiver
Slave Address
R/W
Direction Bit
ACK from
Receiver
1
SCL
2
6
7
8
9
ACK
START
1
2
3-8
8
9
ACK
Repeat if More Bytes Transferred
STOP or
Repeated
START
The bus protocol (as shown in Figure 19) is defined as:
ni
Bus Not Busy. Data and clock lines remain HIGH.
Start Data Transfer. A change in the state of the data line, from HIGH to LOW, while the clock is HIGH, defines a START condition.
Stop Data Transfer. A change in the state of the data line, from LOW to HIGH, while the clock line is HIGH, defines the STOP condition.
Data Valid. The state of the data line represents valid data, when, after a START condition, the data line is stable for the duration of the
HIGH period of the clock signal. There is one clock pulse per bit of data.
Each data transfer is initiated with a START condition and terminated with a STOP condition. The number of data bytes transferred
between START and STOP conditions is not limited and is determined by the master device. The information is transferred byte-wise and
each receiver acknowledges with a ninth-bit.
Within the I²C bus specifications a high-speed mode (3.4MHz clock rate) is defined.
- Acknowledge: Each receiving device, when addressed, is obliged to generate an acknowledge after the reception of each byte. The master device must generate an extra clock pulse that is associated with this acknowledge bit. A device that acknowledges must pull down the
SDA line during the acknowledge clock pulse in such a way that the SDA line is stable LOW during the HIGH period of the acknowledge
clock pulse. Of course, setup and hold times must be taken into account. A master must signal an end of data to the slave by not generat-
Te
ch
-
ca
- Data transfer may be initiated only when the bus is not busy.
- During data transfer, the data line must remain stable whenever the clock line is HIGH. Changes in the data line while the clock line is
HIGH will be interpreted as control signals.
The bus conditions are defined as:
www.austriamicrosystems.com/LED-Driver-ICs/AS1115
Revision 1.08
9 - 25
AS1115
Datasheet - D e t a i l e d D e s c r i p t i o n
al
id
ing an acknowledge bit on the last byte that has been clocked out of the slave. In this case, the slave must leave the data line HIGH to
enable the master to generate the STOP condition.
- Figure 19 on page 9 details how data transfer is accomplished on the I²C bus. Depending upon the state of the R/W bit, two types of
data transfer are possible:
- Master Transmitter to Slave Receiver. The first byte transmitted by the master is the slave address, followed by a number of data bytes.
The slave returns an acknowledge bit after the slave address and each received byte.
- Slave Transmitter to Master Receiver. The first byte, the slave address, is transmitted by the master. The slave then returns an acknowledge bit. Next, a number of data bytes are transmitted by the slave to the master. The master returns an acknowledge bit after all received
bytes other than the last byte. At the end of the last received byte, a not-acknowledge is returned. The master device generates all of the
serial clock pulses and the START and STOP conditions. A transfer is ended with a STOP condition or a repeated START condition. Since
a repeated START condition is also the beginning of the next serial transfer, the bus will not be released.
The AS1115 can operate in the following slave modes:
am
lc s
on A
te G
nt
st
il
lv
- Slave Receiver Mode. Serial data and clock are received through SDA and SCL. After each byte is received, an acknowledge bit is transmitted. START and STOP conditions are recognized as the beginning and end of a serial transfer. Address recognition is performed by
hardware after reception of the slave address and direction bit.
- Slave Transmitter Mode. The first byte (the slave address) is received and handled as in the slave receiver mode. However, in this mode
the direction bit will indicate that the transfer direction is reversed. Serial data is transmitted on SDA by the AS1115 while the serial clock
is input on SCL. START and STOP conditions are recognized as the beginning and end of a serial transfer.
I²C Device Address Byte
The address byte (see Figure 20) is the first byte received following the START condition from the master device.
Figure 20. I²C Device Address Byte
predefined address:
updated address:
MSB
6
5
4
3
2
1
LSB
0
0
0
0
0
0
0
R/W
MSB
6
5
4
3
2
1
LSB
0
0
0
0
0
A1
A0
R/W
ch
ni
ca
- The default slave address is factory-set to 0000000.
- The two LSB bits of the address byte are the device select bits, A0 to A1, which can be set by the self address command after startup. A
maximum of four devices with the same pre-set code can therefore be connected on the same bus at one time.
A short writes a logical “0” whereas an open writes a logical “1” as address bit (see Figure 26 on page 15).
- The last bit of the address byte (R/W) define the operation to be performed. When set to a 1 a read operation is selected; when set to a 0
a write operation is selected.
Following the START condition, the AS1115 monitors the I²C bus, checking the device type identifier being transmitted. Upon receiving the
address code, and the R/W bit, the slave device outputs an acknowledge signal on the SDA line.
I²C Device Self Addressing
Te
If this feature is used, 2 of the 16 key readback nodes can be left open or shorted for self-addressing. This is done with KEYA together with
SEGG (A0) and SEGF (A1). This two nodes cannot be used for key-readback in this case. After startup all devices have the predefined address
0000000. A single command for self addressing will update all connected AS1115. This command has to be done after startup or every time the
AS1115 gets disconnected from the supply. The I²C address definition must be done with fixed connection, since I²C detection is excluded from
debounce time of key registers.
www.austriamicrosystems.com/LED-Driver-ICs/AS1115
Revision 1.08
10 - 25
AS1115
Datasheet - D e t a i l e d D e s c r i p t i o n
Command Byte
The AS1115 operation, (see Table 6) is determined by a command byte (see Figure 21 on page 11).
Figure 21. Command Byte
6
5
4
3
2
1
LSB
D15
D14
D13
D12
D11
D10
D09
D08
al
id
MSB
Figure 22. Command and Single Data Byte Received
From Master to Slave
S
0
R/W A
D8
D7
D6
D5
A
Command Byte
D4
D3
D2
D1
D0
A
Data Byte
am
lc s
on A
te G
nt
st
il
Slave Address
D15 D14 D13 D12 D11 D10 D9
lv
AS1115 Registers
From Slave to Master
P
1 Byte
Acknowledge
from AS1115
Acknowledge
from AS1115
0
Acknowledge
from AS1115
0
0
Autoincrement
Memory Word
Address
Figure 23. Setting the Pointer to a Address Register to select a Data Register for a Read Operation
From Master to Slave
AS1115 Registers
From Slave to Master
S
0
Slave Address
D15 D14 D13 D12 D11 D10 D9
R/W A
A
Command Byte
Acknowledge
from AS1115
0
P
0
ca
Acknowledge
from AS1115
D8
ni
Figure 24. Reading nBytes from AS1115
Auto increment
Memory Word
Address
From Master to Slave
ch
From Slave to Master
Te
S
Acknowledge
from AS1115
Slave Address
Acknowledge
from Master
0
Stop reading
Not Acknowledge
from Master
0
1
n Bytes
R/W A
1
First Data Byte
D7
D6
D5
D4
D3
D2
A
D1
AS1115 Registers
www.austriamicrosystems.com/LED-Driver-ICs/AS1115
Revision 1.08
D0
/A
Second Data Byte
D7
D6
D5
D4
D3
D2
D1
P
D0
Auto increment
to next address
11 - 25
AS1115
Datasheet - D e t a i l e d D e s c r i p t i o n
Initial Power-Up
On initial power-up, the AS1115 registers are reset to their default values, the display is blanked, and the device goes into shutdown mode. At
this time, all registers should be programmed for normal operation.
Note: The default settings enable only scanning of one digit; the internal decoder is disabled and the Intensity Control Register (see page
17) is set to the minimum values.
al
id
Shutdown Mode
The AS1115 devices feature a shutdown mode, where they consume only 200nA (typ) current. Shutdown mode is entered via a write to the Shutdown Register (see Table 7). During shutdown mode the Digit-Registers maintain their data.
Shutdown mode can either be used as a means to reduce power consumption or for generating a flashing display (repeatedly entering and leaving shutdown mode). For minimum supply current in shutdown mode, logic input should be at GND or VDD (CMOS logic level).
lv
When entering or leaving shutdown mode, the Feature Register is reset to its default values (all 0s) when Shutdown Register bit D7 (page 13) =
0.
am
lc s
on A
te G
nt
st
il
Note: When Shutdown Register bit D7 = 1, the Feature Register is left unchanged when entering or leaving shutdown mode. If the AS1115
is used with an external clock, Shutdown Register bit D7 should be set to 1 when writing to the Shutdown Register.
Digit- and Control-Registers
The AS1115 devices contain 8 Digit-Registers,11 control-registers and 10 diagnostic-registers, which are listed in Table 6. All registers are
selected using a 8-bit address word, and communication is done via the I²C interface.
Digit Registers – These registers are realized with an on-chip 64-bit memory. Each digit can be controlled directly without rewriting the
whole register contents.
Control Registers – These registers consist of decode mode, display intensity, number of scanned digits, shutdown, display test and features selection registers.
Type
Table 6. Register Address Map
Address
Register
D15:D13
Digit 0
Digit 2
Digit 3
Digit 4
Digit 5
Digit 6
D9
D8
D7:D0
Page
000
0
0
0
0
1
N/A
0
0
0
1
0
N/A
000
0
0
0
1
1
000
0
0
1
0
0
000
0
0
1
0
1
000
0
0
1
1
0
N/A
000
0
0
1
1
1
N/A
000
0
1
0
0
0
N/A
(see Table 9 on page 14,
Table 10 on page 14 and
Table 11 on page 15)
N/A
N/A
N/A
000
0
1
0
0
1
(see Table 8 on page 13)
13
Global Intensity
000
0
1
0
1
0
(see Table 17 on page 17)
17
Scan Limit
000
0
1
0
1
1
(see Table 19 on page 17)
17
Shutdown
000
0
1
1
0
0
(see Table 7 on page 13)
12
Self Addressing
001
0
1
1
0
1
Feature
000
0
1
1
1
0
N/A
(see Table 20 on page 18)
18
13
Display Test Mode
000
0
1
1
1
1
(see Table 14 on page 16)
DIG0:DIG1 Intensity
000
1
0
0
0
0
(see Table 18 on page 17)
Te
Control Register
ni
Decode-Mode
D10
ch
Digit 7
D11
000
ca
Digit Register
Digit 1
D12
DIG2:DIG3 Intensity
000
1
0
0
0
1
(see Table 18 on page 17)
DIG4:DIG5 Intensity
000
1
0
0
1
0
(see Table 18 on page 17)
DIG6:DIG7 Intensity
000
1
0
0
1
1
(see Table 18 on page 17)
www.austriamicrosystems.com/LED-Driver-ICs/AS1115
Revision 1.08
12 - 25
AS1115
Datasheet - D e t a i l e d D e s c r i p t i o n
Address
Register
Page
D12
D11
D10
D9
D8
Diagnostic Digit 0
000
1
0
1
0
0
N/A
Diagnostic Digit 1
000
1
0
1
0
1
N/A
Diagnostic Digit 2
000
1
0
1
1
0
N/A
Diagnostic Digit 3
000
1
0
1
1
1
N/A
Diagnostic Digit 4
000
1
1
0
0
0
Diagnostic Digit 5
000
1
1
0
0
1
Diagnostic Digit 6
000
1
1
0
1
0
Diagnostic Digit 7
000
1
1
0
1
1
KEYA
000
1
1
1
0
0
KEYB
000
1
1
1
0
1
D7:D0
al
id
D15:D13
N/A
N/A
N/A
N/A
lv
Keyscan/Diagnostic Register
Type
Table 6. Register Address Map
am
lc s
on A
te G
nt
st
il
The Shutdown Register controls AS1115 shutdown mode.
Table 7. Shutdown Register Format (Address (HEX) = 0x0C))
Mode
Shutdown Mode,
Reset Feature Register to Default Settings
Shutdown Mode, Feature Register Unchanged
Normal Operation,
Reset Feature Register to Default Settings
Normal Operation, Feature Register Unchanged
Register Data
HEX Code
D7
D6
D5
D4
D3
D2
D1
D0
0x00
0
X
X
X
X
X
X
0
0x80
1
X
X
X
X
X
X
0
0x01
0
X
X
X
X
X
X
1
0x81
1
X
X
X
X
X
X
1
Decode Enable Register (0x09)
The Decode Enable Register sets the decode mode. BCD/HEX decoding (either BCD code – characters 0:9, E, H, L, P, and -, or HEX code –
characters 0:9 and A:F) is selected by bit D2 (page 18) of the Feature Register. The Decode Enable Register is used to select the decode mode
or no-decode for each digit. Each bit in the Decode Enable Register corresponds to its respective display digit (i.e., bit D0 corresponds to digit 0,
bit D1 corresponds to digit 1 and so on). Table 9 lists some examples of the possible settings for the Decode Enable Register bits.
Note: A logic high enables decoding and a logic low bypasses the decoder altogether.
ca
When decode mode is used, the decoder looks only at the lower-nibble (bits D3:D0) of the data in the Digit-Registers, disregarding bits D6:D4.
Bit D7 sets the decimal point (SEG DP) independent of the decoder and is positive logic (bit D7 = 1 turns the decimal point on). Table 9 lists the
code-B font; Table 10 lists the HEX font.
ni
When no-decode mode is selected, data bits D7:D0 of the Digit-Registers correspond to the segment lines of the AS1115. Table 11 shows the
1:1 pairing of each data bit to the appropriate segment line.
ch
Table 8. Decode Enable Register Format Examples
HEX Code
No decode for digits 7:0
Code-B/HEX decode for digit 0. No decode for digits 7:1
Code-B/HEX decode for digit 0:2. No decode for digits 7:3
Code-B/HEX decode for digits 0:5. No decode for digits 7:6
Code-B/HEX decode for digits 0,2,5.
No decode for digits 1, 3, 4, 6, 7
Te
Decode Mode
www.austriamicrosystems.com/LED-Driver-ICs/AS1115
0x00
0x01
0x07
0x3F
D7
0
0
0
0
D6
0
0
0
0
D5
0
0
0
1
0x25
0
0
1
Revision 1.08
Register Data
D4 D3
0
0
0
0
0
0
1
1
0
0
D2
0
0
1
1
D1
0
0
1
1
D0
0
1
1
1
1
0
1
13 - 25
AS1115
Datasheet - D e t a i l e d D e s c r i p t i o n
Figure 25. Standard 7-Segment LED Intensity Control and Inter-Digit Blanking
A
F
B
G
E
DP
Table 9. Code-B Font
D7
D6:D4
D3 D2 D1 D0
Character
Register Data
D7
D6: D4
D3 D2 D1 D0
X
0
0
0
0
X
0
1
1
0
X
0
0
0
1
X
0
1
1
1
X
0
X
0
X
0
X
0
*
Character
Register Data
D7
D6:D4
D3 D2 D1 D0
lv
Register Data
X
1
1
0
0
X
1
1
0
1
am
lc s
on A
te G
nt
st
il
Character
al
id
C
D
0
1
0
X
1
0
0
0
X
1
1
1
0
0
1
1
X
1
0
0
1
X
1
1
1
1
1
0
0
X
1
0
1
0
X
X
X
X
X
1
0
1
X
1
0
1
1
*
1
The decimal point can be enabled with every character by setting bit D7 = 1.
Table 10. HEX Font
Register Data
D7
D6:D4
X
0
0
0
0
0
0
0
1
ni
X
D3 D2 D1 D0
Character
ca
Character
0
Te
ch
X
*
Register Data
D7
D6: D4
D3 D2 D1 D0
Character
Register Data
D7
D6:D4
D3 D2 D1 D0
X
0
1
1
0
X
1
1
0
0
X
0
1
1
1
X
1
1
0
1
0
1
0
X
1
0
0
0
X
1
1
1
0
X
1
1
1
1
X
X
X
X
X
X
0
0
1
1
X
1
0
0
1
X
0
1
0
0
X
1
0
1
0
X
0
1
0
1
X
1
0
1
1
*
1
The decimal point can be enabled with every character by setting bit D7 = 1.
www.austriamicrosystems.com/LED-Driver-ICs/AS1115
Revision 1.08
14 - 25
AS1115
Datasheet - D e t a i l e d D e s c r i p t i o n
Table 11. No-Decode Mode Data Bits and Corresponding Segment Lines
D7
DP
Corresponding Segment Line
D6
A
D5
B
D4
C
D3
D
D2
E
D1
F
D0
G
I²C Self Addressing
al
id
If this feature is used, 2 of the 16 key readback nodes can be left open or shorted for self-addressing. This is done with KEYA together with
SEGG (A0) and SEGF (A1). This two nodes cannot be used for key-readback in this case. After startup all devices have the predefined address
0000000. A single command for self addressing will update all connected AS1115. This command has to be done after startup or every time the
AS1115 gets disconnected from the supply. The I²C address definition must be done with fixed connection, since I²C detection is excluded from
debounce time of key registers.geht
Note: A short writes a logical “0” whereas an open writes a logical “1” as address bit (see Figure 26).
D7
X
X
Figure 26. Address Coding
Keyscan Register
D6
X
X
D5
X
X
D4
X
X
D3
X
X
D2
X
X
D1
X
X
D0
0
1
am
lc s
on A
te G
nt
st
il
Factory-set IC address
User-set IC address
lv
Table 12. Self Addressing Register (Address (HEX) = 0x2D))
ca
These two registers contain the result of the keyscan input of the 16 keys. To ensure proper results the data in these registers are updated only
if the logic data scanned is stable for 20ms (debounce time). A change of the data stored within these two registers is indicated by a logic low on
the IRQ pin. The IRQ is high-impedance if a read operation on the key scan registers is started.
Table 13. LED Diagnostic Register Address
ni
Register HEX Address
D7
D6
D5
Segment
D4
D3
D2
D1
D0
DP
A
B
C
E
F
G
D
ch
0x1C
0x1D
Key
KEYA
KEYB
Te
Note: If I²C self addressing is used segment G&F of KEYA is used for the two LSB of the I²C address. In this case these two nodes cannot be
used as a key. Additionally the debounce time is disabled for these two bits.
The data within the keyscan register is updated continuously during every cycle (1/10 of refresh rate). Therefore, to get a valid readback of keys it is recommended to read out the keyscan registers immediately after the IRQ is triggered. A short writes a logical “0”
whereas an open writes a logical “1” as keyscan register bit.
Note: If the blink_en bit (bit D4 in the Feature Register 0x0E) is set to ‘1’, the keyscan is not returning a valid value.
www.austriamicrosystems.com/LED-Driver-ICs/AS1115
Revision 1.08
15 - 25
AS1115
Datasheet - D e t a i l e d D e s c r i p t i o n
Display-Test Mode
The AS1115 can detect open or shorted LEDs. Readout of either open LEDs or short LEDs is possible, as well as a OR relation of open and
short.
Note: All settings of the digit- and control-registers are maintained.
Table 14. Testmode Register Summary
D6
RSET_short
D5
RSET_open
D4
LED_global
D3
LED_test
D2
LED_open
D1
LED_short
D0
DISP_test
al
id
D7
X
Table 15. Testmode Register Bit Description (Address (HEX) = 0x0F))
Addr: 0x0F
Address
Bit Name
Default
Access
D7:D0
D0
DISP_test
0
W
Optical display test. (Testmode for external visual test.)
0: Normal operation; 1: Run display test (All digits are tested independently
from scan limit & shutdown register.)
D1
LED_short
0
W
Starts a test for shorted LEDs. (Can be set together with D2)
0: Normal operation; 1: Activate testmode
D2
LED_open
0
W
Starts a test for open LEDs. (Can be set together with D1)
0: Normal operation; 1: Activate testmode
D3
LED_test
0
R
Indicates an ongoing open/short LED test
0: No ongoing LED test; 1: LED test in progress
D4
LED_global
0
R
Indicates that the last open/short LED test has detected an error
0: No error detected; 1: Error detected
D5
RSET_open
0
R
Checks if external resistor RSET is open
0: RSET correct; 1: RSET is open
D6
RSET_short
0
R
Checks if external resistor RSET is shorted
0: RSET correct; 1: RSET is shorted
0
-
Not used
am
lc s
on A
te G
nt
st
il
lv
Bit
D7
LED Diagnostic Registers
These eight registers contain the result of the LED open/short test for the individual LED of each digit.
Table 16. LED Diagnostic Register Address
DP
D6
A
D5
B
D4
C
ni
DIG0
DIG1
DIG2
DIG3
D7
ca
Segment
Digit
D3
D2
D
E
D1
F
D0
G
Register
HEX
Address
0x18
0x19
0x1A
0x1B
Segment
Digit
D7
D6
D5
D4
D3
D2
D1
D0
DIG4
DIG5
DIG6
DIG7
DP
A
B
C
D
E
F
G
ch
Register
HEX
Address
0x14
0x15
0x16
0x17
Note: If one or more short occures in the LED array, detection of individual LED fault could become ambiguous.
Intensity Control Register (0x0A)
Te
The brightness of the display can be controlled by digital means using the Intensity Control Registers and by analog means using RSET (see
Selecting RSET Resistor Value and Using External Drivers on page 19). The intensity can be controlled globally for all digits, or
for each digit individually. The global intensity command will write intensity data to all four individual brightness registers, while the individual
intensity command will only write to the associated individual intensity register.
www.austriamicrosystems.com/LED-Driver-ICs/AS1115
Revision 1.08
16 - 25
AS1115
Datasheet - D e t a i l e d D e s c r i p t i o n
Display brightness is controlled by an integrated pulse-width modulator which is controlled by the lower-nibble of the Intensity Control Register.
The modulator scales the average segment-current in 16 steps from a maximum of 15/16 down to 1/16 of the peak current set by RSET.
Table 17. Intensity Register Format
1/16 (min on)
2/16
3/16
4/16
5/16
6/16
7/16
8/16
0xX0
0xX1
0xX2
0xX3
0xX4
0xX5
0xX6
0xX7
MSB
0
0
0
0
0
0
0
0
Register Data
D2
D1
0
0
0
0
0
1
0
1
1
0
1
0
1
1
1
1
LSB
0
1
0
1
0
1
0
1
Duty Cycle
HEX Code
9/16
10/16
11/16
12/16
13/16
14/16
15/16
15/16 (max on)
0xX8
0xX9
0xXA
0xXB
0xXC
0xXD
0xXE
0xXF
Table 18. Intensity Register Address
0x0A
0x10
0x11
0x12
0x13
Register Data
D2
D1
0
0
0
0
0
1
0
1
1
0
1
0
1
1
1
1
LSB
0
1
0
1
0
1
0
1
Register Data
am
lc s
on A
te G
nt
st
il
Register HEX Address
MSB
1
1
1
1
1
1
1
1
al
id
HEX Code
lv
Duty Cycle
Type
Global
Digit
Digit
Digit
Digit
D7:D4
X
Digit 1 Intensity
Digit 3 Intensity
Digit 5 Intensity
Digit 7 Intensity
D3:D0
Global Intensity
Digit 0 Intensity
Digit 2 Intensity
Digit 4 Intensity
Digit 6 Intensity
Scan-Limit Register (0x0B)
The Scan-Limit Register controls which of the digits are to be displayed. When all 8 digits are to be displayed, the update frequency is typically
700Hz. If the number of digits displayed is reduced, the update frequency is increased. The frequency can be calculated using 10 x fOSC/(N+2),
where N is the number of digits.
Note: To avoid differences in brightness this register should not be used to blank parts of the display (leading zeros).
Table 19. Scan-Limit Register Format (Address (HEX) = 0x0B))
0xX0
0xX1
0xX2
0xX3
Register Data
D7:D3 D2 D1 D0
X
0
0
0
X
0
0
1
X
0
1
0
X
0
1
1
Scan Limit
HEX
Code
Display digits 0:4
Display digits 0:5
Display digits 0:6
Display digits 0:7
0xX4
0xX5
0xX6
0xX7
Register Data
D7:D3 D2 D1 D0
X
1
0
0
X
1
0
1
X
1
1
0
X
1
1
1
Te
ch
ni
Display digit 0 only
Display digits 0:1
Display digits 0:2
Display digits 0:3
HEX
Code
ca
Scan Limit
www.austriamicrosystems.com/LED-Driver-ICs/AS1115
Revision 1.08
17 - 25
AS1115
Datasheet - D e t a i l e d D e s c r i p t i o n
Feature Register (0x0E)
The Feature Register is used for enabling various features including switching the device into external clock mode, applying an external reset,
selecting code-B or HEX decoding, enabling or disabling blinking, setting the blinking rate, and resetting the blink timing.
Note: At power-up the Feature Register is initialized to 0.
Table 20. Feature Register Summary
D6
D5
D4
D3
D2
D1
blink_
start
sync
blink_
freq_sel
blink_en
NU
decode_sel
reg_res
Table 21. Feature Register Bit Descriptions (Address (HEX) = 0xXE)
clk_en
D1
reg_res
D2
decode_sel
D3
NU
D4
blink_en
D5
blink_freq_sel
D6
sync
D7
blink_start
lv
D0
am
lc s
on A
te G
nt
st
il
Bit Name
Feature Register
Enables and disables various device features.
Default
Access
Bit Description
External clock active.
0
R/W
0 = Internal oscillator is used for system clock.
1 = Pin CLK of the serial interface operates as system clock input.
Resets all control registers except the Feature Register.
0 = Reset Disabled. Normal operation.
0
R/W
1 = All control registers are reset to default state (except the Feature Register)
identically after power-up.
Note: The Digit Registers maintain their data.
Selects display decoding for the selected digits (Table 8 on page 13).
0 = Enable Code-B decoding (see Table 9 on page 14).
0
R/W
1 = Enable HEX decoding (see Table 10 on page 14).
Not used
Enables blinking.
0
R/W
0 = Disable blinking. 1 = Enable blinking.
Sets blink with low frequency (with the internal oscillator enabled):
0 = Blink period typically is 1 second (0.5s on, 0.5s off).
0
R/W
1 = Blink period is 2 seconds (1s on, 1s off).
Synchronizes blinking on the rising edge of pin LD/CS. The multiplex and blink timing
counter is cleared on the rising edge of pin LD/CS. By setting this bit in multiple devices,
0
R/W
the blink timing can be synchronized across all the devices.
Start Blinking with display enabled phase. When bit D4 (blink_en) is set, bit D7
determines how blinking starts.
0
R/W
0 = Blinking starts with the display turned off.
1 = Blinking starts with the display turned on.
Te
ch
ni
Bit
clk_en
ca
Addr: 0xXE
D0
al
id
D7
www.austriamicrosystems.com/LED-Driver-ICs/AS1115
Revision 1.08
18 - 25
AS1115
Datasheet - Ty p i c a l A p p l i c a t i o n
9 Typical Application
Selecting RSET Resistor Value and Using External Drivers
Brightness of the display segments is controlled via RSET. The current that flows into ISET defines the current that flows through the LEDs.
al
id
Segment current is about 200 times the current in ISET. Typical values for RSET for different segment currents, operating voltages, and LED voltage drop (VLED) are given in Table 22 & Table 23. The maximum current the AS1115 can drive is 47mA. If higher currents are needed, external drivers must be used, in which case it is no longer necessary that the devices drive high currents.
Note: The display brightness can also be logically controlled (see Intensity Control Register (0x0A) on page 16).
Table 22. RSET vs. Segment Current and LED Forward Voltage, VDD = 2.7V & 3.3V & 3.6V
VLED
VLED
VLED
2.0V
2.5V
1.5V
2.0V
5kΩ
6.9kΩ
10.7kΩ
22.2kΩ
4.4kΩ
5.9kΩ
9.6kΩ
20.7kΩ
6.7kΩ
9.1kΩ
13.9kΩ
28.8kΩ
6.4kΩ
8.8kΩ
13.3kΩ
27.7kΩ
5.7kΩ
8.1kΩ
12.6kΩ
26kΩ
7.5kΩ
10.18kΩ
15.6kΩ
31.9kΩ
7.2kΩ
9.8kΩ
15kΩ
31kΩ
2.5V
3.0V
lv
1.5V
VDD = 3.6V
2.0V
VDD = 3.3V
1.5V
6.6kΩ
9.2kΩ
14.3kΩ
29.5kΩ
am
lc s
on A
te G
nt
st
il
40
30
20
10
VDD = 2.7V
ISEG (mA)
5.5kΩ
7.5kΩ
13kΩ
27.3kΩ
Table 23. RSET vs. Segment Current and LED Forward Voltage, VDD = 4.0V & 5.0V
VLED
VLED
2.0V
2.5V
3.0V
3.5V
1.5V
2.0V
2.5V
3.0V
3.5V
4.0V
40
30
20
10
8.6kΩ
11.6kΩ
17.7kΩ
36.89kΩ
8.3kΩ
11.2kΩ
17.3kΩ
35.7kΩ
7.9kΩ
10.8kΩ
16.6kΩ
34.5kΩ
7.6kΩ
9.9kΩ
15.6kΩ
32.5kΩ
5.2kΩ
7.8kΩ
13.6kΩ
29.1kΩ
11.35kΩ
15.4kΩ
23.6kΩ
48.9kΩ
11.12kΩ
15.1kΩ
23.1kΩ
47.8kΩ
10.84kΩ
14.7kΩ
22.6kΩ
46.9kΩ
10.49kΩ
14.4kΩ
22kΩ
45.4kΩ
10.2kΩ
13.6kΩ
21.1kΩ
43.8kΩ
9.9kΩ
13.1kΩ
20.2kΩ
42kΩ
VDD = 5.0V
1.5V
VDD = 4.0V
ISEG
(mA)
Calculating Power Dissipation
The upper limit for power dissipation (PD) for the AS1115 is determined from the following equation:
PD = (VDD x 5mA) + (VDD - VLED)(DUTY x ISEG x N)
Where:
(EQ 1)
ni
Dissipation Example:
ca
VDD is the supply voltage.
DUTY is the duty cycle set by intensity register (page 17).
N is the number of segments driven (worst case is 8)
VLED is the LED forward voltage
ISEG = segment current set by RSET
(EQ 2)
PD = 5V(5mA) + (5V - 2.2V)(15/16 x 40mA x 8) = 0.865W
(EQ 3)
ch
ISEG = 40mA, N = 8, DUTY = 15/16, VLED = 2.2V at 40mA, VDD = 5V
Thus, for a TQFN(4x4)-24 package ΘJA = +30.5°C/W, the maximum allowed TAMB is given by:
(EQ 4)
Te
TJ,MAX = TAMB + PD x ΘJA = 150°C = T AMB + 0.865W x 30.5°C/W
In this example the maximum ambient temperature must stay below 123.61°C.
www.austriamicrosystems.com/LED-Driver-ICs/AS1115
Revision 1.08
19 - 25
AS1115
Datasheet - Ty p i c a l A p p l i c a t i o n
8x8 Dot Matrix Mode
The application example in Figure 27 shows the AS1115 in the 8x8 LED dot matrix mode.
The LED columns have common cathodes and are connected to the DIG0:7 outputs. The rows are connected to the segment drivers. Each of
the 64 LEDs can be addressed separately. The columns are selected via the digits as listed in Table 6 on page 12.
al
id
The Decode Enable Register (see page 13) must be set to ‘00000000’ as described in Table 8 on page 13. Single LEDs in a column can
be addressed as described in Table 11 on page 15, where bit D0 corresponds to segment G and bit D7 corresponds to segment DP.
Figure 27. Application Example as LED Dot Matrix Driver
VDD
2.7 to 5V
DIG0 to
DIG7
ISET
SDA
SDA
µP
IRQ
SCL
am
lc s
on A
te G
nt
st
il
SCL
AS1115
SEG A to G
SEP DP
Diode Arrangement
lv
9.53kΩ
IRQ
GND
Keyscan
The key readback of the AS1115 can be used either for push buttons as well as switches. If only a single key is pressed (shorted) at a time no
additional diodes are required. If a detection of multiple simultaneous keystrokes is required diodes within the keypath, as shown in Figure 28,
are required. Pressing multiple keys without the diodes would result in ambiguous results. Since KEYA and KEYB have independent inputs only
keys on the same path are affected.
Figure 28. Keyscan Configuration
KEYA
KEYB
ch
ni
IRQ
SEGB
ca
SEGA
SEGC
SEGD
SEG E
SEGF
SEGG
SEGDP
Diodes are optional and only required if multiple keystrokes must be
detected simultaneously.
If I²C Self-Addressing is used these two keys cannot be used for readback and must be either hard wired opened or shorted.
A short writes a logical “0” whereas an open writes a logical “1” as
address bit.
Note: If the blink_en bit (bit D4 in the Feature Register 0x0E) is set to ‘1’, the keyscan is not returning a valid value.
Te
Supply Bypassing and Wiring
In order to achieve optimal performance the AS1115 should be placed very close to the LED display to minimize effects of electromagnetic interference and wiring inductance.
Furthermore, it is recommended to connect a 10µF and a 0.1µF ceramic capacitor between pins VDD and GND to avoid power supply ripple
(see Figure 27).
www.austriamicrosystems.com/LED-Driver-ICs/AS1115
Revision 1.08
20 - 25
AS1115
Datasheet - P a c k a g e D r a w i n g s a n d M a r k i n g s
10 Package Drawings and Markings
am
lc s
on A
te G
nt
st
il
lv
al
id
Figure 29. QSOP-24 Marking
Figure 30. TQFN(4x4)-24 Marking
Table 24. Packaging Code
YY
WW
manufacturing week
R/X
ZZ
plant identifier
free choice / traceability code
Te
ch
ni
ca
last two digits of the current year
www.austriamicrosystems.com/LED-Driver-ICs/AS1115
Revision 1.08
21 - 25
AS1115
Datasheet - P a c k a g e D r a w i n g s a n d M a r k i n g s
Te
ch
ni
ca
am
lc s
on A
te G
nt
st
il
lv
al
id
Figure 31. QSOP-24 Package
www.austriamicrosystems.com/LED-Driver-ICs/AS1115
Revision 1.08
22 - 25
AS1115
Datasheet - P a c k a g e D r a w i n g s a n d M a r k i n g s
Te
ch
ni
ca
am
lc s
on A
te G
nt
st
il
lv
al
id
Figure 32. TQFN(4x4)-24 Package
www.austriamicrosystems.com/LED-Driver-ICs/AS1115
Revision 1.08
23 - 25
AS1115
Datasheet - O r d e r i n g I n f o r m a t i o n
11 Ordering Information
The devices are available as the standard products shown in Table 25.
Table 25. Ordering Information
Description
64 LEDs, I²C Interfaced LED Driver with
Keyscan
Delivery Form
Tape and Reel
Tape and Reel
Note: All products are RoHS compliant and austriamicrosystems green.
Buy our products or get free samples online at ICdirect: http://www.austriamicrosystems.com/ICdirect
Technical Support is found at http://www.austriamicrosystems.com/Technical-Support
Te
ch
ni
ca
am
lc s
on A
te G
nt
st
il
For further information and requests, please contact us mailto:[email protected]
or find your local distributor at http://www.austriamicrosystems.com/distributor
Package
QSOP-24
TQFN(4x4)-24
al
id
Marking
AS1115
AS1115
lv
Ordering Code
AS1115-BSST
AS1115-BQFT
www.austriamicrosystems.com/LED-Driver-ICs/AS1115
Revision 1.08
24 - 25
AS1115
Datasheet
Copyrights
Copyright © 1997-2012, austriamicrosystems AG, Tobelbaderstrasse 30, 8141 Unterpremstaetten, Austria-Europe. Trademarks Registered ®.
All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of
the copyright owner.
All products and companies mentioned are trademarks or registered trademarks of their respective companies.
al
id
Disclaimer
lv
Devices sold by austriamicrosystems AG are covered by the warranty and patent indemnification provisions appearing in its Term of Sale.
austriamicrosystems AG makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding
the freedom of the described devices from patent infringement. austriamicrosystems AG reserves the right to change specifications and prices at
any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with austriamicrosystems AG for
current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range,
unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are
specifically not recommended without additional processing by austriamicrosystems AG for each application. For shipments of less than 100
parts the manufacturing flow might show deviations from the standard production flow, such as test flow or test location.
ca
am
lc s
on A
te G
nt
st
il
The information furnished here by austriamicrosystems AG is believed to be correct and accurate. However, austriamicrosystems AG shall not
be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use,
interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing,
performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of
austriamicrosystems AG rendering of technical or other services.
Headquarters
ni
Contact Information
ch
austriamicrosystems AG
Tobelbaderstrasse 30
A-8141 Unterpremstaetten, Austria
Te
Tel: +43 (0) 3136 500 0
Fax: +43 (0) 3136 525 01
For Sales Offices, Distributors and Representatives, please visit:
http://www.austriamicrosystems.com/contact
www.austriamicrosystems.com/LED-Driver-ICs/AS1115
Revision 1.08
25 - 25