5mm WHITE LAMP LED IWL-W5FH1F-TNB SPECIFICATION ① Product : 5mm WHITE FLAT TYPE LAMP ② Part No : IWL-W5FH1F-TNB ③ Customer : ④ Date : 2008. 06. 10 Ver.1.1 Customer : Checked By Checked By Checked By Checked By Approval Manufacturer : ITSWELL Co., LTD Proposed By Checked By Checked By Checked By Approval Comment Incheon Factory 58B-4L 626-3 Gozan-dong Namdong-gu Incheon-city 405-817 KOREA Tel: 82-31-814-1972 FAX: 82-31-822-9009 Ochang Factory & Head Office : 363-880, 9-4Block, Ochang Scientific Industrial Complex, 1115-4 Namchon-ri, Oksan-myeon, Chengwongun, Chungbuk 363-911 Korea URL : www.itswell.com, TEL : int) 82-43-218-1800, FAX.: int) 82-43-218-1805 IWL-W5FH1F-TNB Version of 1.1 PAGE : ‹#› / 10 5mm WHITE LAMP LED IWL-W5FH1F-TNB ■ Features • • • • • Flat type lamp 5mm resin mold type Colored White ,Clear transparency lens type High luminous intensity Chip material based GaN ■ Absolute Maximum Ratings(Ta=25℃) Parameter Symbol Value Unit Pd 114 mW Continuous Forward Current IF 30 mA Peak Forward Current IFP 100 mA Reverse Voltage VR 5 V Operating Temperature Topr -25 ~ 80 ℃ Storage Temperature Tstg -40 ~100 ℃ Soldering Temperature Tsol 260 (5 sec) ℃ Power Dissipation ※1 ※1 Duty ratio = 1/10, Pulse width = 0.1ms ■ Electro-optical Characteristics(Ta=25℃) Parameter Symbol Condition Min. Typ. Max. Unit Forward Voltage ※2 VF IF= 20mA 2.8 3.4 3.8 V Reverse Voltage VRZ IRZ= 5mA - 0.9 1.5 V IV IF= 20mA 425 555 1600 mcd 2Θ 1/2 IF= 20mA - 110 - deg. - IF= 20mA - x;:0.3 Y:0.3 - - Luminous Intensity ※3 Viewing angle ※4 Chromaticity Coordinates ※5 ※2 Luminous Intensity is tested by a tester calibrated by CAS 140B(CIE LED_B) and has an accuracy of 10% ※3 Viewing angle is the angle until 50% of brightness measured from the front part of LED. ※4 Dominant wavelength has an accuracy of ±1nm. IWL-W5FH1F-TNB Version of 1.1 PAGE : ‹#› / 10 5mm WHITE LAMP LED IWL-W5FH1F-TNB ■ CIE Rank (IF=20mA, Ta=25℃) A B C D E F X Y X Y X Y X Y X Y X Y 0.25 0.209 0.26 0.263 0.27 0.239 0.28 0.253 0.29 0.268 0.3 0.323 0.25 0.249 0.26 0.223 0.27 0.279 0.28 0.293 0.29 0.308 0.3 0.283 0.26 0.263 0.27 0.239 0.28 0.293 0.29 0.308 0.3 0.323 0.31 0.297 0.26 0.223 0.27 0.279 0.28 0.253 0.29 0.268 0.3 0.283 0.31 0.337 0.25 0.209 0.26 0.263 0.27 0.239 0.28 0.253 0.29 0.268 0.3 0.323 0.32 0.33 0.34 A- A-1 X Y X Y 0.23 0.18 0.24 0.193 0.23 0.22 0.24 0.235 0.24 0.235 0.25 0.249 0.24 0.193 0.25 0.209 0.23 0.18 0.24 0.193 0.24 0.25 0.38 0.37 0.36 0.35 0.34 0.33 0.32 0.31 0.3 0.29 0.28 0.27 0.26 0.25 0.24 0.23 0.22 0.21 0.2 0.19 0.18 0.17 0.22 0.23 * x,y coordinates for white lamp 0.26 0.27 0.28 0.29 0.3 0.31 * The CIE(1931) standard colorimetric system * Chromaticity coordinates Measured : 0.01sr(CIE. LED_B) * Measurement Uncertainty of the Color Coordinates : ±0.005 IWL-W5FH1F-TNB Version of 1.1 PAGE : ‹#› / 10 5mm WHITE LAMP LED IWL-W5FH1F-TNB ■ Typical Curves Forward Current vs. Forward Voltage Forward Current vs. Ambient Temperature 40 DC Forward Current(mA) Forward Current(mA) 100 10 1 2.0 2.5 3.0 3.5 4.0 Forward Voltage(V) 10 0 0 20 40 60 80 Ambient Temperature(?℃ ) 10 1 20 40 60 Ambient Temperature(?℃ ) 80 Relative Intensity vs. Wavelength 150 100 50 0 0 10 20 Forward Current(mA) Relative intensity 30 Radiation Diagram 0 1.0 30 0.8 0.6 30 60 60 0.4 0.2 0.0 400 100 Relative Luminous Intensity vs. Forward Current Relative Luminous Intensity(%) Relitive Luminous Intensity 20 4.5 Relative Luminous Intensity vs. Ambient Temperature 0.1 0 30 90 1.0 500 600 700 Wavelength(nm) 90 0.5 0 0.5 1.0 800 IWL-W5FH1F-TNB Relative Lumminous Intensity(%) Version of 1.1 PAGE : ‹#› / 10 5mm WHITE LAMP LED IWL-W5FH1F-TNB ■ Out Line Dimension - With Stopper - Without Stopper 1 1 2 1 2 2 1 1 2 2 ■ Taping Dimension & Packing - Bulk Packing □ Inner Box □ Bag packing Label 75 105 230 □ Out Packing ▪ Maximum Inner Box 20 / 1 Box 30,000 pcs/ 1 Box ▪ Out box material : Carton IWL-W5FH1F-TNB Version of 1.1 PAGE : ‹#› / 10 5mm WHITE LAMP LED IWL-W5FH1F-TNB - Tapping Packing Note : 1. All dimensions are in millimeters. 2. Tolerance is ±0.5mm Out Box Label Taping Box Tapping Box (Carton) 1 Tapping box / Pack with Silica gel 2,000 pcs/ 1 Tapping IWL-W5FH1F-TNB Maximum 10 tapping box / Box 20,000 pcs/ Box Version of 1.1 PAGE : ‹#› / 10 5mm WHITE LAMP LED IWL-W5FH1F-TNB ■ Precaution in use ① Soldering Conditions When soldering Dome LED , Heat may affect the electrical and optical characteristics of the LEDs. In soldering, do not stress the lead frame and the resin part under the high temperature. The epoxy part should be protected from mechanical stress or vibration until the Dome LEDs return to room temperature after soldering. ▪ Preliminary heating to be at 180℃ max. for 120 Seconds max. ▪ Soldering heat to be at 260℃ max. for 5sec. Max. ▪ For manual Soldering is Not more than 3sec @MAX350℃, under soldering iron ℃ 6 ℃Max. 5sec g n0 i 5 t a 1 e~ h0 -2 e1 r P . c e s / 5 . 2 ~ 2 ℃ 0 4 2 . x a M . c e s 5 . 2 ~ 2 ) ( p m e T ℃ 60sec. Max. Above 200℃ . x a M . c e s 0 2 1 ) . c e s ( e m i T ② Storage Use with 7days after opening packing. Store in 10 to 30 ℃ Dome LED lead frames are plated silver. The silver surface may be affected by environment which contain corrosive gases and so on. Please avoid condition which may cause the Dome LED to corroded, tarnish or discolor. ③ Static Electricity Static electricity or surge voltage damages the Dome LEDs. It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs. A tip soldering iron is requested to be grounded. An ionizer should also be installed where risk of static. All devices, equipment and machinery must be properly grounded (via 1MΩ). It is recommended that measures be taken against surge voltage to the equipment that mounts the Dome LEDs. ④ Cleaning Isopropyl Alcohol or Ethylene Alcohol is recommended in 5 minutes at room temperature. Don’t use unspecified chemical may cause crack or haze on the surface of the epoxy resin. Before cleaning, a pre-test should be done to confirm whether any damage to the Dome LED will occur. Freon solvents should not be used to clean the Dome LEDs because of worldwide regulations. IWL-W5FH1F-TNB Version of 1.1 PAGE : ‹#› / 10 5mm WHITE LAMP LED IWL-W5FH1F-TNB ■ Reliability - Reliability Test Item Standard Test Method Test Item Test Conditions Number of Damaged Note Resistance to Soldering Heat (Reflow Soldering) JEITA ED-4701 300 301 Tsld = 260℃, 5sec. (Pretreatment 30 ℃, 70%, 168hrs) 2 times 0/50 Solderabilty (Reflow Soldering) JEITA ED-4701 200 303 Tsld = 235 ± 5℃, 5sec. (Lead Solder) 1 time Over 95% 0/50 Thermal Shock JEITA ED-4701 100 105 -40 ℃ ~ 100 ℃ 15sec 15sec 100 Cycles 0/50 Temperature Cycle JEITA ED-4701 100 105 -40 ℃ ~ 25℃~ 100℃ ~ 25 ℃, 30min 5min 30min 5min 100 Cycles 0/50 High Temp. Storage JEITA ED-4701 200 201 Ta = 100℃ 1000hrs 0/50 Temp. Humidity Storage JEITA ED-4701 100 103 Ta = 60 ℃, RH = 90% 1000hrs 0/50 Low Temp. Storage JEITA ED-4701 200 202 Ta = -40 ℃ 1000hrs 0/50 0/50 Steady State Operating Life Condition - Ta = 25 ℃, IF = 20mA 1000hrs Steady State Operating Life of High Temp. - Ta = 85 ℃, IF = 5mA 1000hrs 0/50 Steady State Operating Life of High Humidity Heat - 60 ℃, RH = 90%, IF = 15mA 500hrs 0/50 Steady State Operating Life of Low Temp. - Ta = -30, IF = 20mA 1000hrs 0/50 - Criteria for Judging the Damage Items Test Conditions Criteria for judgment Luminous Intensity ( IV ) IF = 20mA > 70% of S Forward Voltage IF = 20mA Less than 120% of U ( VF ) * U means the upper limit of specified characteristics, S means initial value. IWL-W5FH1F-TNB Version of 1.1 PAGE : ‹#› / 10 5mm WHITE LAMP LED IWL-W5FH1F-TNB ■ Part Name Description I W L – W 5 F H1 F - TNB Option : T : Water clear, N : Without Stopper, B : Bulk F : With Flange View Angle : 1100 F : Flat Type Size : 5mm Color : White L : Dome LED Lamp IT : Company Name, ITSWELL Co., Ltd. ■ ATTENTION : Electric Static Discharge (ESD) Protection The symbol shown on the page herein to introduce ‘Electro-Optical Characteristics’. ESD protection for GaP and AlGaAs is based chips is still Necessary even though they are safe in low static-electric discharge. Material in AlInGaP, GaP, or/and InGaN based chips are static sensitive devices. ESD protection has to considered and taken in the initial design stage. If manual work/process is needed, please ensure the device is well protective From ESD during all the process. LED’s ESD Level is ‘Class 2’ and The range of Forward Voltage is 1999V ~ 3999V. ■ ATTENTION : Precaution in drive I Reverse Voltage 0.7V V LED+Zener Diode ▪ Do not apply reverse voltage more than 0.7V. ▪ Product with Zener Diode is needed to discriminate the characteristics of product by fixing current and measuring voltage. IWL-W5FH1F-TNB Version of 1.1 PAGE : ‹#› / 10 5mm WHITE LAMP LED IWL-W5FH1F-TNB ■ Spec. Review History Review Ver. Date Correction List Ver 1.1 2008.06.10 Establish IWL-W5FH1F-TNB Etc. Version of 1.1 PAGE : ‹#› / 10