Topview 1608 Red LEDs IWS-165-RXWF SPECIFICATION Product : Red SMD LED (1608, 0.5t) Part No. : IWS-165-RXWF Customer : Date : 2006. 01. 25 Ver. 1.0 Customer : Checked By Checked By Checked By Checked By Approval Manufacturer : ITSWELL Co., LTD Proposed By Checked By Checked By Checked By Approval Comment Suwon Company : 442-190, 802 Uman Industrial Comples, 300-5 Uman-dong, Paldal-gu, Gyeonggi-do, Korea Tel:+82-31-244-0002, FAX:+82+31-244-1806 Ochang Company : 363-880, 9-4Block, Ochang Scientific Industrial Complex, Ochang, Cheongwon, Chungbuk, Korea URL : www.itswell.com, TEL : int) 82-43-218-1800, FAX.: int) 82-43-218-1805 IWS –165-RXWF Version of 1. 0 PAGE : 1 / 10 Topview 1608 Red LEDs IWS-165-RXWF 1. Features ▪ High Luminous Intensity : Long operation life ▪ Low Current Application : Low power consumption ▪ Excellent Uniformity on Color, Intensity and Forward Current ▪ 100% Probing Test 2. Applications ▪ Telecommunication : Indicator and backlighting in telephone ▪ Flat Key Pad backlight for Mobile, switch and symbol ▪ Indoor sign boards ▪ General Use 3. Outline Drawing and Dimension Tolerance : ± 0.1 Unit : mm Cathode 1 2 Anode Recommendable soldering pattern IWS –165-RXWF Version of 1. 0 PAGE : 2 / 10 Topview 1608 Red LEDs IWS-165-RXWF 4. Absolute Maximum Ratings Items Symbols Ratings Unit Operation Forward Current IF 20 mA Peak Pulsed Forward Current*1 IPF 60 mA Power Dissipation PD 48 mW Reverse Voltage VR 5 V Operating Temperature Range Top -30 ~ +85 ℃ Storage Temperature Range TS -40 ~ +100 ℃ TSOL 260±5 ℃ Soldering Temperature * 1 Duty ratio = 1/10, Pulse width = 0.1ms 5. Electrical & Optical Characteristics (Ta : 25℃) Parameter Symbol Conditions Min. Typ. Max. Unit. Forward Voltage VF IF = 5 mA 1.7 2.0 2.5 V Reverse Current IR VR = 5 V - - 10 uA Luminous Intensity*2 IV IF = 5 mA 20 - 78 mcd WD IF = 5 mA 618 - 635 nm 2Θ1/2 IF = 5 mA - 130 - º Dominant Wavelength*3 View Angle*4 • 2 Luminous Intensity is tested by a tester calibrated by CAS 140B(CIE LED_B) and has an accuracy of 10% • 3 Dominant wavelength has an accuracy of ±1nm. • 4 Viewing angle is the angle until 50% of brightness measured from the front part of LED. 5.1 Luminous Intensity Rank 5.3 Forward Voltage Rank Rank Luminous Intensity (mcd) Rank Forward Voltage (V) E 20 - 28 a 1.7 - 1.9 F 28 - 40 b 1.9 - 2.1 G 40 - 56 c 2.1 - 2.3 H 56 - 78 d 2.3 - 2.5 5.2 Dominant Wavelength Rank Rank Dominant wavelength (nm) A 618 - 635 IWS –165-RXWF Version of 1. 0 PAGE : 3 / 10 Topview 1608 Red LEDs IWS-165-RXWF 6. Typical Characteristic Curve Forward Current vs. Forward Voltage Forward Current vs. Ambient Temperature 30 10 1 0.1 0.01 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 Forward Voltage(V) Relative Luminous Intensity vs. Ambient Temperature Relitive Luminous Intensity 10 1 0.1 -40 -20 0 20 40 60 Ambient Temperature( ℃ ) 80 Relative Luminous Intensity vs. Wavelength 20 10 0 0 20 40 60 80 o Ambient Temperature( C) 100 Luminous Intensity vs. Forward Current Relative Luminous Intensity(%) DC Forward Current(mA) Forward Current(mA) 100 300 250 200 150 100 50 0 10 20 30 40 Forward Current(mA) 50 Radiation Diagram Y 100 X Relative Intensity(%) X 80 Y 60 40 20 0 500 550 600 650 700 750 800 Wavelength(nm) IWS –165-RXWF Relative Luminous Intensity(%) Version of 1. 0 PAGE : 4 / 10 Topview 1608 Red LEDs IWS-165-RXWF 7. Dimension of Tape / Reel Unit : mm MA X5 ˚ A' 0.20 B' (2.75) 4.00 *R *R 0.55 1.8 A 3.50 B 8.00 2.00 1.75 4.00 SECTION B-B' 0.90 MA X5 ˚ *R Tolerance ±0.1 , Unit: mm *R SECTION A-A' Label 부착 위치 80 70 X ×50 37 Scale 기호표시위치 Index Label (1) Quantity : Product are packed in one taping reel of max. 4,000 pcs. (2) Cumulative Tolerance : Cumulative Tolerance/10 pitches to be ±0.2mm (3) Adhesion Strength of Cover Tape : Adhesion strength to be 0.1-0.7N when the cover tape is turned off from the carrier tape at 10℃ angle to be the carrier tape. (4) Packaging : P/N, Manufacturing data Code No. and quantity to be indicated on a damp proof Package. IWS –165-RXWF Version of 1. 0 PAGE : 5 / 10 Topview 1608 Red LEDs IWS-165-RXWF 8. Packing Dimension 250 Bake: 60°C, 4hrs 220 Label Label Wheel Diameter : 180 mm Width : 12 mm 1608 ⇒ 4,000 pcs/Reel Shield Bag(Polyester/Al/LDPE) 1 Reel/Bag ( T = 0.1 mm ) with Silica gel Al Pack & Reel Label, Box Label (70 × 37) RANK # Lot : IWS-165-RXWF MIN AVG MAX CHIP LED 226 STD VF[volt] IV[mcd] WD[nm] Q’ty : yyyy/mm/dd www.itswell.com 150 224 Maximum 10 Bags / 1 Inner Box 1608 ⇒ 40,000 pcs / 1 Inner Box IWS –165-RXWF Version of 1. 0 PAGE : 6 / 10 Topview 1608 Red LEDs IWS-165-RXWF 9. Precaution in use 9.1 Soldering Conditions When soldering SMD LED , Heat may affect the electrical and optical characteristics of the LEDs. In soldering, do not stress the lead frame and the resin part under the high temperature. The epoxy part should be protected from mechanical stress or vibration until the SMD LEDs return to room temperature after soldering. ▪ Preliminary heating to be at 150℃ max. for 180 Seconds max. ▪ Soldering heat to be at 260℃ max. for 5 sec. Max. ▪ For manual Soldering is Not more than 3 sec @MAX 350 ℃, under soldering iron <Recommendable soldering pattern> 120~180sec.Max 9.2 Storage Use with 7days after opening packing. Store in 10 to 30 ℃ SMD LED lead frames are plated silver. The silver surface may be affected by environment which contain corrosive gases and so on. Please avoid condition which may cause the SMD LED to corroded, tarnish or discolor. 9.3 Static Electricity Static electricity or surge voltage damages the SMD LEDs. It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs. A tip soldering iron is requested to be grounded. An ionizer should also be installed where risk of static. All devices, equipment and machinery must be properly grounded (via 1MΩ). It is recommended that measures be taken against surge voltage to the equipment that mounts the SMD LEDs. 9.4 Cleaning Isopropyl Alcohol or Ethylene Alcohol is recommended in 5 minutes at room temperature. Don’t use unspecified chemical may cause crack or haze on the surface of the epoxy resin. Before cleaning, a pre-test should be done to confirm whether any damage to the SMD LED will occur. Freon solvents should not be used to clean the LEDs because of worldwide regulations. IWS –165-RXWF Version of 1. 0 PAGE : 7 / 10 Topview 1608 Red LEDs IWS-165-RXWF 10. Reliability 10.1 Reliability Test Item Test Items Test Conditions Notes High Temperature Storage 85 ℃, 500 hr. 0/32 Low Temperature Storage -30 ℃, 500 hr. 0/32 Temp. Humidity Storage 50 ℃, 95 % RH, 500 hr. 0/32 Steady State Operating life 25 ℃, 5 mA , 500 hr. 0/32 High Temperature Operating Life 85 ℃, 5 mA, 500 hr. 0/32 Low Temperature Operating Life -30 ℃, 5 mA, 500 hr. 0/32 Steady State Operating life Of High Humidity Heat 50 ℃, 95 % RH, 5 mA 500 hr. 0/32 Temperature Cycle -40 ℃(30 min) → 25 ℃ (5 min.) → 100 ℃ (30 min.) → 25 ℃ (5 min.), 100 cycle 0/22 ESD HBM, 100pF, 1.5kohm, 3 times (Contact Mode : 0/22 Forward Min 2kV, Reverse Min 200V) Pressure Cooker Test 121℃, 2 atm., 99.6 % RH, 48hr. 0/22 10.2 Criteria for Judging the Damage Items Test Conditions Criteria for judgment Luminous Intensity ( IV ) IF = 5 mA More than > 50% of S Forward Voltage ( VF ) IF = 5 mA Less than 120% of U Reverse Current ( IR ) VR = 5 V Less than 10㎂ * U means the upper limit of specified characteristics, S means initial value. IWS –165-RXWF Version of 1. 0 PAGE : 8 / 10 Topview 1608 Red LEDs IWS-165-RXWF 11. Part Name Description I W S – 1 6 5 – RXWF Red color series 165 : 1.6 mm x 0.8 mm, 0.5 mm t dimension SMD Type Chip LED Company Name, ITSWELL Co., Ltd. 12. Rank Description E A a Forward Voltage (VF) Dominant wavelength (WD) Luminous intensity (IV) 13. ATTENTION : Electric Static Discharge (ESD) Protection The symbol shown on the page herein to introduce ‘Electro-Optical Characteristics’. ESD protection for GaP and AlGaAs is based chips is still Necessary even though they are safe in low static-electric discharge. Material in AlInGaP, GaP, or/and InGaN based chips are STATIC SENSITIVE devices. ESD protection has to considered and taken in the initial design stage. If manual work/process is needed, please ensure the device is well protective From ESD during all the process. LED’s ESD Level is ‘Class II’ and The range of Forward Voltage is 2000V ~ 3999V. After opening the package, the LED’s should be kept at 30℃, 70%RH or less. The LEDs must be dip soldered within seven days(168 hours) after opening the moisture-proof packing. It is better not to use different rank LEDs. If use mixed rank, could not attain your object for highest quality of products. IWS –165-RXWF Version of 1. 0 PAGE : 9 / 10 Topview 1608 Red LEDs IWS-165-RXWF ■ Spec. Review History Review Ver. Date Correction List Ver 1.0 2006. 1.25 Establish IWS –165-RXWF Etc. Version of 1. 0 PAGE : 10 / 10