Topview 3528 SMD LED IWS-L3514-CW-K2

Topview 3528 SMD LED
IWS-L3514-CW-K2
SPECIFICATION
Product : Topview 3528 White SMD LED
Part No. : IWS-L3514-CW-K2
Date : 2010. 04. 19 Ver. 2.0
Proposed By Checked By
Checked By
Checked By
Approval
Comment
ITSWELL Co., Ltd
58B-4L, 626-3 Gojan-dong, Namdong-gu, Incheon 405-817 KOREA
TEL:+82-32-813-1801, FAX:+82+32-816-1900
URL: http://www.itswell.com,
IWS-L3514-CW-K2
Version of 2.0
PAGE : 1 / 12
Topview 3528 SMD LED
IWS-L3514-CW-K2
1. Features
• 2 Chip High-Luminosity SMD LED
• 3.5 x 2.8 x 1.9 mm (L x W x H), Small Size Surface Mount Type
• Wide Viewing Angle
• Long Operating Life
2. Applications
• Automotive: Backlight in Dashboard and Switch
• Lighting Device: Indicator, General Lighting
• Camera Flash, Hand Carrier Flash
• General Use
3. Outline Drawing and Dimension
Unit : mm, Tolerance : ±0.1mm
(1)
(3)
(2)
(4)
[ Top view ]
[ Bottom view ]
(1)
(3)
(2)
Cathode
(4)
Anode
[ Side view ]
[ Circuit diagram ]
Note
1. All dimensions are in millimeters
2. All dimensions without tolerances are for reference only
IWS-L3514-CW-K2
Version of 2.0
PAGE : 2 / 12
Topview 3528 SMD LED
IWS-L3514-CW-K2
4. Absolute Maximum Ratings( Ta = 25 ℃ )
Parameter
Symbol
Value
Unit
Power Dissipation
Pd
216
mW
Continuous Forward Current
IF
60
mA
Peak Forward Current ※1
IFP
200
mA
Operating Temperature
Topr
-30 ~ 85
℃
Storage Temperature
Tstg
-40 ~100
℃
Soldering Temperature
Tsol
260 (5sec)
℃
※1 Duty ratio = 1/10, Pulse width = 0.1ms
5. Electro-optical Characteristics( Ta = 25 ℃ )
Parameter
Symbol
Conditions
Min.
Typ.
Max.
Unit.
Forward Voltage (per chip)
VF
IF = 40 mA
2.8
3.2
3.6
V
Reverse Voltage (per chip)
VR
IR = 5 mA
0.7
0.8
1.5
V
Luminous Intensity ※2
IV
IF = 40 mA
2100
-
4500
mcd
Color Coordinates ※3
CIE x
CIE y
IF = 40 mA
Viewing Angle ※4
2θ1/2
IF = 40 mA
Refer to Color Coordinates Rank
-
120
-
º
※2
Luminous Intensity is tested by a tester calibrated by CAS 140B(CIE LED_B) and has an accuracy of 10%
Color Coordinates has an accuracy of ±0.01.
※4 Viewing Angle is the angle until 50% of brightness measured from the front part of LED.
※3
5.1 Luminous Intensity Rank
5.2 Forward Voltage Rank
Rank
Luminous Intensity (mcd)
Rank
Forward Voltage (V)
N
2100 – 2700
0
2.8 ~ 3.0
P
2700 – 3500
2
3.0 ~ 3.2
Q
3500 – 4500
4
3.2 ~ 3.4
6
3.4 ~ 3.6
IWS-L3514-CW-K2
Version of 2.0
PAGE : 3 / 12
Topview 3528 SMD LED
IWS-L3514-CW-K2
5.3 Color Coordinates Rank ( IF = 40 mA, Ta = 25 ℃ )
BW
CW
Z1
Z2
A1
A2
B1
B2
x
y
x
y
x
y
x
y
x
y
x
y
0.2400
0.2000
0.2500
0.2100
0.2600
0.2200
0.2700
0.2300
0.2800
0.2400
0.2900
0.2500
0.2400
0.2600
0.2500
0.2700
0.2600
0.2800
0.2700
0.2900
0.2800
0.3000
0.2900
0.3100
0.2500
0.2700
0.2600
0.2800
0.2700
0.2900
0.2800
0.3000
0.2900
0.3100
0.3000
0.3200
0.2500
0.2100
0.2600
0.2200
0.2700
0.2300
0.2800
0.2400
0.2900
0.2500
0.3000
0.2600
PW
7500K
7040K-4746K
8145-7040K
7040K-6020K
Y
6020K-5331K
V1
6500K
5331K-4746K
V2
7040K-6530K
V3
5700K
6530K-6020K
Z
6020K-5665K
A
B
x
y
x
y
x
y
x
y
x
y
x
y
x
y
0.3057
0.2671
0.3125
0.2842
0.3243
0.2951
0.3353
0.3053
0.3089
0.3012
0.3152
0.3070
0.3229
0.3142
0.2891
0.3175
0.3089
0.3012
0.3229
0.3142
0.3362
0.3259
0.3008
0.3399
0.3095
0.3484
0.3198
0.3585
0.3025
0.3321
0.3229
0.3142
0.3362
0.3259
0.3500
0.3371
0.3095
0.3484
0.3198
0.3585
0.3282
0.3652
0.3140
0.2770
0.3243
0.2951
0.3353
0.3053
0.3472
0.3164
0.3152
0.3070
0.3229
0.3142
0.3292
0.3200
PW
NW
5700K
5000K
4500K
5665K-5311K
5311K-5028K
5028K-4746K
4746K-4503K
4503K-4260K
4260K-3985K
C
L
M
D
E
F
3985K-3710K
G
x
y
x
y
x
y
x
y
x
y
x
y
x
y
0.3292
0.3200
0.3362
0.3259
0.3429
0.3317
0.3500
0.3371
0.3574
0.3428
0.3648
0.3479
0.3755
0.3550
0.3282
0.3652
0.3381
0.3732
0.3465
0.3797
0.3562
0.3843
0.3650
0.3899
0.3756
0.3966
0.3882
0.4044
0.3381
0.3732
0.3465
0.3797
0.3567
0.3881
0.3650
0.3899
0.3756
0.3966
0.3882
0.4044
0.4035
0.4134
0.3362
0.3259
0.3429
0.3317
0.3500
0.3371
0.3574 0.3428
WW
0.3648
0.3479
0.3755
0.3550
0.3865
0.3617
3500K
3000K
2700K
3710K-3465K
3465K-3220K
3220K-3045K
3045K-2870K
2870K-2670K
J
K
P
Q
R
2670K-2500K
S
x
y
x
y
x
y
x
y
x
y
x
y
0.3865
0.3617
0.3988
0.3684
0.4117
0.3745
0.4221
0.3790
0.4599
0.4329
0.4767
0.4360
0.4022
0.4094
0.4165
0.4169
0.4332
0.4241
0.4456
0.4287
0.4767
0.4360
0.4921
0.4374
0.4165
0.4169
0.4332
0.4241
0.4456
0.4287
0.4599
0.4329
0.4486
0.3875
0.4621
0.3902
0.3988
0.3684
0.4117
0.3745
0.4221
0.3790
0.4344
0.3833
0.4344
0.3833
0.4486
0.3875
IWS-L3514-CW-K2
Version of 2.0
PAGE : 4 / 12
Topview 3528 SMD LED
IWS-L3514-CW-K2
CIE y
Chromaticity Diagram
CIE x
IWS-L3514-CW-K2
Version of 2.0
PAGE : 5 / 12
Topview 3528 SMD LED
IWS-L3514-CW-K2
6. Typical Characteristics Curves
Forward Current vs.
Ambient Temperature
Ta=25℃
80
DC Forward Current(mA)
Forward Current(mA)
Forward Current vs.
Forward Voltage
100
10
1
2.0
2.5
3.0
3.5
4.0
Forward Voltage(V)
20
40
60
o
Lead Temperature( C)
Relative Luminous Intensity(%)
Relitive Luminous Intensity
40
30
20
10
20
40
60
80
100
o
Relative Luminous Intensity vs.
Forward Current
IF=40mA
0
50
Ambient Temperature( C)
1
0.1
60
0
0
4.5
Relative Luminous Intensity vs.
Ambient Temperature
10
70
80
Ta=25℃
125
100
75
50
25
0
0
10
20
30
40
50
Forward Current(mA)
60
Radiation Diagram
Relative Intensity vs. Wavelength
Ta=25℃, IF=40mA
Ta=25℃
0.6
0.4
0.2
0.0
400
0
1 IF=40mA
0.8
Relative Luminoussity(a.u)
Relative intensity
1.0
500
600
700
Wavelength(nm)
IWS-L3514-CW-K2
800
10
20
30
40
50
60
0.5
70
80
0
90
60
30
Radiation Angle
0
Version of 2.0
0.5
PAGE : 6 / 12
90
1
Topview 3528 SMD LED
IWS-L3514-CW-K2
7. Dimension of Tape / Reel
7.1 Tape Dimension
B
Cathode
A
A'
Anode
B'
< SECTION B-B'>
Tolerance ±0.1 , Unit: mm
< SECTION A-A'>
7.2 Reel Dimension
Label
IWS-L3514-CW-K2
Version of 2.0
PAGE : 7 / 12
Topview 3528 SMD LED
IWS-L3514-CW-K2
8. Packing Dimension
Unit :mm
Aluminum Shield Bag
Reel
250
Bake: 60°C, 48hrs
220
Label
Label
Reel
Inclouding Silica gel in a bag
Card board Box
Al Pack Label, Reel Label
(70 × 37)
CHIP LED
Lot :
226
IWS-L3514-CW-K2
MIN
AVG
MAX
STD
Label
VF[volt]
Iv[mcd]
CCT[K]
Q’ty :
yyyy/mm/dd
www.itswell.com
150
224
Dimensions (mm)
Reel / Box
Q’ty / Box(pcs)
Reel
Φ180mm,
12mm Width
–
2,000 Max
Al Shield Bag
250x220
–
2,000 Max
Card board Box
224x150x226
10 Max
20,000 Max
IWS-L3514-CW-K2
Version of 2.0
PAGE : 8 / 12
Topview 3528 SMD LED
IWS-L3514-CW-K2
9. Precaution in use
9.1 Soldering Conditions
 When soldering Power SMD, Heat may affect the electrical and optical characteristics of the
LEDs.
 In soldering, do not stress the lead frame and the resin part under the high temperature.
 The silicone part should be protected from mechanical stress or vibration until the Power SMD
return to room temperature after soldering.
▪ Preliminary heating to be at 160 ℃ max. for 120 Seconds max.
▪ Soldering heat to be at 260 ℃ max. for 5 sec. Max.
▪ For manual Soldering is Not more than 3 sec @MAX 350 ℃, under soldering iron
< Lead Free >
260℃ Max.
5sec. Max.
<Recommendable soldering pattern>
<Unit: mm>
1~5 ℃/sec
Pre-heating
140~160℃
1~5 ℃/sec
120sec.Max.
60sec.Max.
Above 220℃
9.2 Storage
 Before opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.
 The LEDs should be used within a year.
 After opening the package, the LEDs should be kept at 30℃ or less and 30%RH or less.
 The LEDs should be used within 168 hours (7 day) after opening the package.
 If the moisture absorbent material (silicagel) has faded away or the LED have exceeded
the storage time, baking treatment should be performed using the following conditions.
Baking treatment: 60℃±5 for 72 hours.
9.3 Static Electricity
 Static electricity or surge voltage damages the Power SMD . It is recommended that a wrist band
or an anti-electrostatic glove be used when handling the LEDs.
 A tip soldering iron is requested to be grounded. An ionizer should also be installed where risk
of static.
 All devices, equipment and machinery must be properly grounded (via 1MΩ). It is recommended
that measures be taken against surge voltage to the equipment that mounts the Power SMD.
9.4 Cleaning
 Isopropyl Alcohol or Ethylene Alcohol is recommended in 5 minutes at room temperature.
Don’t use unspecified chemical may cause crack or haze on the surface of the epoxy resin.
 Before cleaning, a pre-test should be done to confirm whether any damage to the LED will occur.
 Freon solvents should not be used to clean the LEDs because of worldwide regulations.
9.5 Heat Generation
 When the LEDs are illuminating, operating current should be decided after being considering
the ambient maximum temperature.
 Please consider the heat generation of the LED when it is designed the PCB.
IWS-L3514-CW-K2
Version of 2.0
PAGE : 9 / 12
Topview 3528 SMD LED
IWS-L3514-CW-K2
10. Reliability
10.1 Reliability Test Item
Test Items
Test Conditions
Notes
High Temperature Storage
100℃, 1,000hr.
0/25
Low Temperature Storage
-40℃, 1,000hr.
0/25
Temp. Humidity Storage
60℃, 90% RH, 1,000hr.
0/25
Steady State Operating life
25℃, 48mA , 1,000hr.
0/25
High Temperature
Operating Life
85℃, 20mA, 1,000hr
0/25
Low Temperature
Operating Life
-30℃, 40mA, 1,000hr.
0/25
Steady State Operating life
Of High Humidity Heat
60℃, 90% RH, 30mA, 1,000hr.
0/25
Thermal Shock
-40℃(30min)↔100℃(30min.), 100 cycle
0/20
ESD
HBM, 100 pF, 1.5 kohm, 3 times
0/20
10.2 Criteria for Judging the Damage
Parameters
Test Conditions
Criteria for judgment
Forward Voltage ( VF )
IF = 40 mA
Less than 110% of U
Luminous Intensity ( IV )
IF = 40 mA
> 70% of S
* U means the upper limit of specified characteristics, S means initial value.
IWS-L3514-CW-K2
Version of 2.0
PAGE : 10 / 12
Topview 3528 SMD LED
IWS-L3514-CW-K2
11. Part Name Description
□□□-□□□□□-□□-□□
Information of Manufacturer
Color
UV : Violet
UB : Blue
UC : Cyan
UG : Green
UY : Yellow
UO : Orange
UR : Red
DR : Deep Red
EI : IR 850nm
NI : IR 950nm
Number of leads
BW : 0.26이하
CW : 0.26<x<0.3
PW : 5000~8000K
NW : 3600~5000K
WW : 2600~3600K
2 : 2 leads
3 : 3 leads
4 : 4 leads
6 : 6 leads
Package Dimension 351 : 3.5x2.8
302 : 3.0x2.0
506 : 5.0x6.2
505 : 5.4x5.0
909 : 9.0x9.0
Frame type P : PCB
M : Metal PCB
L : PLCC
C : Ceramic
S : Slug type
S : SMD type LED package
IW : ITSWELL Co., Ltd. (Company Name)
12. Rank Description
P
A1
2
Forward Voltage Rank
Color Coordinates Rank
Luminous Intensity Rank
13. Attention : Electric Static Discharge (ESD) Protection
The symbol shown on the page herein to introduce ‘Electro-Optical
Characteristics’. ESD protection for GaP and AlGaAs is based chips is still
Necessary even though they are safe in low static-electric discharge.
Material in AlInGaP, GaP, or/and InGaN based chips are STATIC SENSITIVE
devices. ESD protection has to considered and taken in the initial design stage.
If manual work/process is needed, please ensure the device is well protective
From ESD during all the process.
IWS-L3514-CW-K2
Version of 2.0
PAGE : 11 / 12
Topview 3528 SMD LED
IWS-L3514-CW-K2
■ Spec. Review History
Review Ver.
Date
Correction List
Ver 1.0
2009.09.28
Established
Ver 2.0
2010.04.19
Changed Color Coordinates Rank
& Recommendable soldering
pattern & Part Name Description
IWS-L3514-CW-K2
Etc.
Version of 2.0
PAGE : 12 / 12