PM75CLA120 Powerex, Inc., 200 E. Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 Intellimod™ L-Series Three Phase IGBT Inverter 75 Amperes/1200 Volts P A E TERMINAL CODE D F G 1 VUPC L 2 UFO M H 3 UP J J J K 4 VUP1 K 5 VVPC K K 6 VFO 7 VP 8 VVP1 9 VWPC 10 WFO Y N 11 WP B 1 Y 5 9 12 VWP1 19 13 VNC P N W 14 VN1 15 NC V B U V 16 UN W 17 VN S 18 WN 19 FO Q AE R U AG (2 PLACES) U T U AC (2 PLACES) AB (6 PLACES) AF AD AA X Z C N W V VUPC OT IN UFO VUP1 Features: £ Complete Output Power Circuit £ Gate Drive Circuit £ Protection Logic – Short Circuit – Over Temperature Using On-chip Temperature Sensing – Under Voltage £ Low Loss Using 5th Generation IGBT Chip FO VCC UP GND GND IN FO VCC SI OUT OT GND GND IN FO VCC SI OUT OT GND GND IN FO VCC SI OUT IN NC GND GND OT VVPC VFO WP VWP1 VP VVP1 UN FO VCC SI OUT GND GND IN FO VCC SI OUT GND GND OT VN SI OUT WFO VWPC NC FO VNC WN VN1 U OT P Outline Drawing and Circuit Diagram Dimensions A B C D E F G H J K L M N P Q R Inches 4.72 2.17 0.63 4.17 0.28 0.78 2.62 0.13 0.63 0.08 0.10 2.81 0.20 0.43 0.42 0.87 Millimeters 120.0 55.0 16.0 106.0 7.0 19.75 66.5 3.25 16.0 2.0 2.5 71.5 5.0 11.0 10.75 22.0 Dimensions S T U V W X Y Z AA AB AC AD AE AF AG Inches 0.46 0.59 0.91 0.57 1.26 1.22 0.69 1.14 0.51 M5 Metric 0.22 Dia. 0.28 0.08 0.02 Sq. 0.10 Dia. Description: Powerex Intellimod™ Intelligent Power Modules are isolated base modules designed for power switching applications operating at frequencies to 20kHz. Built-in control circuits provide optimum gate drive and protection for the IGBT and free-wheel diode power devices. Millimeters 11.75 15.0 23.0 14.5 32.0 31.0 17.5 29.0 13.0 M5 Dia. 5.5 7.0 2.0 Sq. 0.5 Dia. 2.5 Applications: £ Inverters £ UPS £ Motion/Servo Control £ Power Supplies Ordering Information: Example: Select the complete part number from the table below -i.e. PM75CLA120 is a 1200V, 75 Ampere Intellimod™ Intelligent Power Module. Type Current Rating Amperes VCES Volts (x 10) PM 75 120 1 Powerex, Inc., 200 E. Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 PM75CLA120 Intellimod™ L-Series Three Phase IGBT Inverter 75 Amperes/1200 Volts Absolute Maximum Ratings, Tj = 25°C unless otherwise specified Characteristics Power Device Junction Temperature Symbol PM75CLA120 Units Tj -20 to 150 °C Tstg -40 to 125 °C Mounting Torque, M5 Mounting Screws — 31 in-lb Mounting Torque, M5 Main Terminal Screws — 31 in-lb Storage Temperature Module Weight (Typical) — 380 Grams Supply Voltage, Surge (Applied between P - N) VCC(surge) 1000 Volts Self-protection Supply Voltage Limit (Short Circuit protection Capability)* VCC(prot.) 800 Volts VISO 2500 Volts VCES 1200 Volts ±IC 75 Amperes ±ICP 150 Amperes PC 457 Watts Supply Voltage (Applied between VUP1-VUPC, VVP1-VVPC, VWP1-VWPC, VN1-VNC) VD 20 Volts Input Voltage (Applied between UP-VUPC, VP-VVPC, WP-VWPC, UN- VN- WN-VNC) VCIN 20 Volts Fault Output Supply Voltage VFO 20 Volts IFO 20 mA Isolation Voltage, AC 1 minute, 60Hz Sinusoidal *VD = 13.5 ~ 16.5V, Inverter Part, Tj = 125°C IGBT Inverter Sector Collector-Emitter Voltage (VD = 15V, VCIN = 15V) Collector Current (TC = 25°C) Peak Collector Current (TC = 25°C) Collector Dissipation (TC = 25°C) Control Sector (Applied between UFO-VUPC, VFO-VVPC, WFO-VWPC, FO-VNC) Fault Output Current (UFO, VFO, WFO, FO Terminals) Electrical and Mechanical Characteristics, Tj = 25°C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units Collector-Emitter Cutoff Current ICES VCE = VCES, VD = 15V, Tj = 25°C — — 1.0 mA VCE = VCES, VD = 15V, Tj = 125°C — — 10 mA Diode Forward Voltage VEC -IC = 75A, VCIN = 15V, VD = 15V — 2.5 3.5 Volts VCE(sat) VD = 15V, VCIN = 0V, IC = 75A, — 1.8 2.3 Volts — 1.9 2.4 Volts IGBT Inverter Sector Collector-Emitter Saturation Voltage Tj = 25°C VD = 15V, VCIN = 0V, IC = 75A, Tj = 125°C Inductive Load Switching Times ton 0.5 1.0 2.5 µs trr VD = 15V, VCIN = 0 ⇔ 15V — 0.5 0.8 µs tC(on) VCC = 600V, IC = 75A — 0.4 1.0 µs toff Tj = 125°C — 2.0 3.0 µs — 0.7 1.2 µs tC(off) 2 Powerex, Inc., 200 E. Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 PM75CLA120 Intellimod™ L-Series Three Phase IGBT Inverter 75 Amperes/1200 Volts Electrical and Mechanical Characteristics, Tj = 25°C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units SC -20°C ≤ Tj ≤ 125°C, VD = 15V 150 — — Amperes toff(SC) VD = 15V — 0.2 — µs OT Trip Level 135 145 155 °C OTR Reset Level — 125 — °C UV Trip Level 11.5 12.0 12.5 Volts UVR Reset Level — 12.5 — Volts ID VD = 15V, VCIN = 15V, VN1-VNC — 15 25 mA Control Sector Short Circuit Trip Level Short Circuit Current Delay Time Over Temperature Protection (Detect Tj of IGBT Chip) Supply Circuit Under-voltage Protection (-20 ≤ Tj ≤ 125°C) Circuit Current VD = 15V, VCIN = 15V, VXP1-VXPC — 5 10 mA Input ON Threshold Voltage Vth(on) Applied between UP-VUPC, 1.2 1.5 1.8 Volts Input OFF Threshold Voltage Vth(off) VP-VVPC, WP-VWPC, UN- VN- WN-VNC 1.7 2.0 2.3 Volts Fault Output Current* IFO(H) VD = 15V, VCIN = 15V — — 0.01 mA IFO(L) VD = 15V, VCIN = 15V — 10 15 mA tFO VD = 15V 1.0 1.8 — ms Min. Typ. Max. Units Fault Output Pulse Width* *Fault output is given only when the internal SC, OT and UV protections schemes of either upper or lower devide operate to protect it. Thermal Characteristics Characteristic Symbol Junction to Case Thermal Resistance Condition Rth(j-c)Q IGBT (Per 1/6 Module) — — 0.21 °C/Watt Rth(j-c)D FWDi (Per 1/6 Module) — — 0.30 °C/Watt Case to Fin Per Module, — — 0.038 °C/Watt Value Units Contact Thermal Resistance Rth(c-f) Thermal Grease Applied Recommended Conditions for Use Characteristic Symbol Supply Voltage Condition VCC Applied across P-N Terminals ≤800 Volts VD Applied between VUP1-VUPC, 15.0 ± 1.5 Volts Control Supply Voltage** VVP1-VVPC, VWP1-VWPC, VN1-VNC Input ON Voltage VCIN(on) Applied between UP-VUPC, ≤0.8 Volts Input OFF Voltage VCIN(off) VP-VVPC, WP-VWPC, UN- VN- WN-VNC ≥9.0 Volts PWM Input Frequency fPWM — ≤20 kHz Arm Shoot-through Blocking Time tDEAD Input Signal ≥2.5 µs ** With ripple satisfying the following conditions: dv/dt swing ≤ ±5V/µs, Variation ≤ 2V peak to peak. TC Measurement Point Arm Y BOTTOM VIEW X Axis UP VP WP UN VN WN IGBT FWDi IGBT FWDi IGBT FWDi IGBT FWDi IGBT FWDi IGBT FWDi X 28.3 28.3 65.0 65.0 87.0 87.0 39.3 39.3 54.0 54.0 76.0 76.0 Y -8.2 2.0 -8.2 2.0 -8.2 2.0 6.2 -4.0 6.2 -4.0 6.2 -4.0 3 Powerex, Inc., 200 E. Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 PM75CLA120 Intellimod™ L-Series Three Phase IGBT Inverter 75 Amperes/1200 Volts FREE-WHEEL DIODE FORWARD CHARACTERISTICS (TYPICAL) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL - INVERTER PART) EMITTER CURRENT, IE, (AMPERES) 1.5 1.0 VD = 15V Tj = 25°C Tj = 125°C 0.5 0 20 40 60 80 101 100 100 COLLECTOR-CURRENT, IC, (AMPERES) VD = 15V Tj = 25°C Tj = 125°C 0 0.5 SWITCHING LOSS, ESW(on), (mJ/PULSE) REVERSE RECOVERY TIME, trr, (µs) 102 10-1 VCC = 600V VD = 15V INDUCTIVE LOAD Tj = 25°C Tj = 125°C 102 NORMALIZED TRANSIENT THERMAL IMPEDANCE, Zth(j-c') Zth = Rth • (NORMALIZED VALUE) EMITTER CURRENT, IE, (AMPERES) 101 100 Single Pulse TC = 25°C Per Unit Base = Rth(j-c) = 0.27°C/W (IGBT) Rth(j-c) = 0.39°C/W (FWDi) 10-2 10-3 10-3 10-2 10-1 TIME, (s) 4 100 2.5 3.0 VCC = 600V VD = 15V INDUCTIVE LOAD Tj = 25°C Tj = 125°C 100 100 101 VCC = 600V VD = 15V Tj = 25°C Tj = 125°C 101 101 102 SWITCHING LOSS (OFF) VS. COLLECTOR CURRENT (TYPICAL) 100 10-1 100 101 EMITTER CURRENT, IE, (AMPERES) 102 COLLECTOR CURRENT, IC, (AMPERES) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (IGBT & FWDi) 10-1 2.0 101 SWITCHING LOSS (ON) VS. COLLECTOR CURRENT (TYPICAL) REVERSE RECOVERY CHARACTERISTICS (TYPICAL) 101 1.5 102 EMITTER-COLLECTOR VOLTAGE, VEC, (VOLTS) 100 10-2 100 1.0 SWITCHING LOSS, ESW(off), (mJ/PULSE) COLLECTOR-EMITTER SATURATION VOLTAGE, VCE(sat), (VOLTS) 2.0 REVERSE RECOVERY CURRENT, Irr, (AMPERES) 102 2.5 0 REVERSE RECOVERY CHARACTERISTICS (TYPICAL) 102 101 VCC = 600V VD = 15V Tj = 25°C Tj = 125°C 100 10-1 100 101 COLLECTOR CURRENT, IC, (AMPERES) 102