ROHM BP5055-12

BP5055-12
Non-isolated AC/DC converter
Dimensions(Unit : mm)
Absolute Maximum Ratings
Case temperature
Tcmax
105
C
Output current
Iomax 1
Iomax 2
250
130
mA
mA
DC
Refer to derating curve
Ambient temperature +
the module self-heating Tcmax
PEAK value of current (Vi= to −420V)
PEAK value of current (Vi=−420 to−600V)
9.9MAX.
28.2MAX.
Conditions
Marking Side
Unit
V
C
C
21.5MAX.
Limits
−600
−20 to 80
−25 to 105
4.0 +1.0
Parameter
Symbol
Input voltage
Vi
Operating temperature range
Topr
Storage temperature range
Tstg
0.5+0.1
1.3 +0.2
3.25MAX.
P=5.08+ 0.2
0.25+0.05
5.55MAX.
2.54x9=22.86TYP.
4.35MAX.
Electrical Characteristics
Unless otherwise specified Ta=25°C, Vi=−311V, IO=250mA
Max.
−600
−13.4
250
130
0.25
0.20
0.20
0.07
0.05
0.08
77
Derating Curve
Conditions
Unit
V
V
mA
mA
V
V
Vp-p
%
Derating Curve
Output Current Io(mA)
Typ.
−311
−12.7
Vi=−240V to −420V
Vi=−420V to −600V
Vi=−240V to −600V lo=130mA
lo=0 to 250mA
Pin No.
1
2
3
4
5
6
7
8
9
10
BP5055-12
Vi
~
ZNR
R1
+
+
10
A
L1
C4
D1
C3
+
V
150
Vo
Be sure to use fuse for safety.
For actual usage, Please kindly evaluate and confirm our part mounted in your product,
Especially, Please make sure to confirm the load current does not exceed Max. rated current
by using the current probe.
External components setting
FUSE: fuse
C1, C2: Input capacitor
Please make sure to use quick acting fuse (1A)
C3: Output capacitor
above 30V, 220 to 1000µF, Low impedance
ESR:0.18Ω Max.
Ripple current 0.65Arms above
Impedance of capacitor effects the output ripple voltage.
50
above 450V, 22 to 100µF
Ripple current 0.7Arms above
100
90
80
70
60
50
40
30
20
10
0
0
Conversion Efficiency
(Ta=25 C, Vi=-311V)
50
100
150
200
Output Current Io(mA)
250
Line Regulation
(Ta=25 C, Io=130mA)
−13.5
−13.3
−13.1
−12.9
−12.7
−12.5
−12.3
−12.1
−11.9
−11.7
−11.5
−200 −250 −300 −350 −400 −450 −500 −550 −600 −650
Input Voltage Vi(V)
Surface Temperature Rising
40
35
30
25
20
15
10
5
0
0
C4: For noise terminal voltage Above 600V, 0.1 to 0.22µF
reduction capacitor
Film capacitor or Ceramic capacitor
Reduce the noise terminal voltage.
The constant value should be evaluated in the product.
L1: Power inductor
Inductance:1.0mH, Rating current: above 0.74A
Choose components that do not easily get magnetically saturated in high temperature.
Recommended part : C13-FR 1.0mH (MITSUMI)
D1: Flywheel diode
Above 1000V, current: above 1.0A
Fast recovery diode
Please note that both the switching and efficiency characteristics of the
module are affected by this diode.
Recommended products: UF4007 (VISHAY)
D2: Rectifier diode
Use a rectifying diode with the peak reverse voltage of 1kV or higher, the
average rectification current of 1A or larger and the peak surge current of
20A or larger. When using an input capacitor of a large capacity, choose a
component that endures the inrush current on power-up.
This product is compatible with full-wave rectification.
R1: For noise terminal voltage 10 to 22Ω, 1W
Reduce the noise terminal voltage.
reduction capacitor
The constant value should be evaluated in the product.
ZNR: Varistor
Vi=−420V to −600V
100
Load Regulation
FUSE
C1
C2
8
Function
Input terminal : Vi(-311VDC)
Skip
Skip
COMMON
Skip
Power inductor terminal
Skip
Power inductor terminal
Skip
Output terminal : Vo(-12.7VDC)
Output Voltage -Vo(V)
D2
6
Vi=−240V to −420V
200
Conversion Efficiency
BP5055-12
4
250
0
-20-10 0 10 20 30 40 50 60 70 80 90
Ambient Temperature Ta( C)
Application circuit
1
300
Conversion Efficiency (%)
Parameter
Symbol Min.
−240
Input voltage range
−12.0
Output voltage
Output current1
lo1
Output current2
lo2
Line regulation
Load regulation
Output ripple voltage
Conversion efficiency
70
Varistor must be used. It protects this part from lightning surge and static electricity.
Surface Temperature Rising
(Ta=25 C, Vi=-311V)
50
100
150
200
Output Current Io(mA)
250
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level
of reliability and the malfunction of which would directly endanger human life (such as medical
instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers
and other safety devices), please be sure to consult with our sales representative in advance.
It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance
of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow
for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in
order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM
cannot be held responsible for any damages arising from the use of the products under conditions out of the
range of the specifications or due to non-compliance with the NOTES specified in this catalog.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact your nearest sales office.
ROHM Customer Support System
www.rohm.com
Copyright © 2007 ROHM CO.,LTD.
THE AMERICAS / EUPOPE / ASIA / JAPAN
Contact us : webmaster@ rohm.co. jp
21, Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan
TEL : +81-75-311-2121
FAX : +81-75-315-0172
Appendix1-Rev2.0