MB3800 - Spansion

The following document contains information on Cypress products.
FUJITSU MICROELECTRONICS
DATA SHEET
DS04-27212-4Ea
ASSP For Power Supply Applications
BIPOLAR
Switching Regulator Controller
(Low Voltage)
MB3800
■ DESCRIPTION
The MB3800 is a single-channel switching regulator control IC for low voltage applications incorporating a soft
start function and short circuit detection function. The device has a low minimum operating voltage of 1.8 V and
is ideal for the power supply of battery-operated electronic equipment.
■ FEATURES
•
•
•
•
•
•
•
•
•
Wide supply voltage operating range: 1.8 V to 15 V
Low current consumption: Typically 5.5 mA in operation, 1 µA or less in stand-by
High speed operation is possible: Maximum 1 MHz
The error amplifier gain is set inside the IC, so peripheral components are minimized.
Incorporates a soft start circuit.
Incorporates a timer-latch type short circuit detection circuit (SCP).
Totem-pole type output with adjustable on/off current (for NPN transistors)
Incorporates a stand-by function.
Three types of packages (SOP-8 : 2 types, SSOP-8 : 1 type)
■ Application
• LCD monitor/panel
• Power supply module
• Portable apparatus
etc.
Copyright©1994-2008 FUJITSU MICROELECTRONICS LIMITED All rights reserved
2006.5
MB3800
■ PIN ASSIGNMENT
(TOP VIEW)
–IN
1
8
FB
SCP
2
7
OSC
V CC
3
6
GND
BR/CTL
4
5
OUT
(FPT-8P-M01)
(FPT-8P-M02)
(FPT-8P-M03)
■ PIN DESCRIPTION
2
Pin No.
Symbol
I/O
Description
1
–IN
I
2
SCP
—
Soft start and SCP setting capacitor connection pin
3
VCC
—
Power supply pin
4
BR/CTL
I
Output current setting and control pin
5
OUT
O
Totem-pole type output pin
6
GND
—
Ground pin
7
OSC
—
Capacitor and resistor connection pin for setting the oscillation frequency
8
FB
O
Error amplifier output pin
Error amplifier inverting input pin
MB3800
■ BLOCK DIAGRAM
V CC
OSC
3
7
Reference
voltage supply
Sawtooth wave
oscillator
0.6 V–
OUT
0.1 V–
5
0.1 V
1.25 V
–IN
1
–
PWM
36 kΩ
+
0.5 V
– Comp.
+
+
+
Error Amp
500 Ω
30 kΩ
Output drive
control circuit
0.3 V
DTC 0.6 V
FB
8
Soft start SCP
6
2
GND
4
SCP
BR/CTL
3
MB3800
■ ABSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Power supply voltage
VCC
Output source current
O+
I
Output sink current
IO–
Allowable dissipation
Storage temperature
PD
Rating
Condition
Unit
Min
Max
—
16
V
—
–50
mA
—
50
mA
FPT-8P-M01, Ta ≤ +25°C
—
570*
mW
FPT-8P-M02, Ta ≤ +25°C
—
430*
mW
SSOP-8, Ta ≤ +25°C
—
580*
mW
—
–55
+125
°C
—
Tstg
*: When mounted on a 10 cm square double-sided epoxy board.
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
■ RECOMMENDED OPERATING CONDITIONS
(Ta = +25°C)
Parameter
Symbol
Value
Unit
Min
Typ
Max
VCC
1.8
—
15
V
VI
–0.2
—
+1.0
V
BR/CTL pin input voltage
VBR
–0.2
—
VCC
V
Output source current
I O+
–40
—
—
mA
Output sink current
IO–
—
—
40
mA
SCP pin capacitance
CPE
—
0.1
—
µF
Phase compensation capacitance
CP
—
0.1
—
µF
Output current setting resistance
RB
150
390
5000
Ω
Timing resistance
RT
1.0
3.0
10.0
kΩ
Timing capacitance
CT
100
270
10000
pF
Oscillation frequency
fOSC
10
500
1000
kHz
Operating Ambient temperature
Ta
–30
+25
+85
°C
Power supply voltage
Error amplifier input voltage
WARNING: The recommended operating conditions are required in order to ensure the normal operation of the
semiconductor device. All of the device’s electrical characteristics are warranted when the device is
operated within these ranges.
Always use semiconductor devices within their recommended operating condition ranges. Operation
outside these ranges may adversely affect reliability and could result in device failure.
No warranty is made with respect to uses, operating conditions, or combinations not represented on
the data sheet. Users considering application outside the listed conditions are advised to contact their
representatives beforehand.
4
MB3800
■ ELECTRICAL CHARACTERISTICS
Parameter
Circuit to prevent
malfunction at low
input voltage
(U.V.L.O.)
Reset voltage
Symbol
Condition
VR
(VCC = +2 V, Ta = +25 °C)
Value
Unit
Min Typ Max
—
—
0.9
V
1.1
1.3
1.5
V
–1.5
–1.0
–0.7
µA
0.7
0.8
0.9
V
–1.5
–1.0
–0.7
µA
0.7
0.8
0.9
V
400
500
600
kHz
—
Threshold voltage
VTH
Charging current
ICS
Soft start
Voltage at soft start
completion
VtS
Short circuit
detection (S.C.P.)
Charging current
ICPC
Threshold voltage
VtPC
Oscillation frequency
fOCS
RT = 3.0 kΩ, CT = 270 pF
Frequency input
stability
fdV
VCC = 2 V to 15 V
—
2
10
%
Frequency variation
with temperature
fdT
Ta = –30°C to +85°C
—
5
—
%
Input threshold
voltage
VT
VFB = 450 mV
480
500
520
mV
VT input stability
VTdV
VCC = 2 V to 15 V
—
5
20
mV
VT variation with
temperature
VTdT
Ta = –30°C to +85°C
—
1
—
%
Input bias current
IB
–1.0
–0.2
+1.0
µA
Voltage gain
AV
70
100
145
V/V
Frequency bandwidth
BW
—
6
—
MHz
Maximum output
voltage range
VOM+
0.78
0.87
—
V
—
0.05
0.2
V
—
–40
–24
µA
24
40
—
µA
65
75
85
%
Sawtooth wave
oscillator (OSC)
Error amplifier
Idle period
adjustment section
VSCP = 0 V
—
VSCP = 0 V
—
VIN = 0 V
—
AV = 0 dB
—
VOM–
OM+
Output source current
I
Output sink current
IOM–
Maximum duty cycle
tDUTY
VFB = 0.45 V
RT = 3.0 kΩ, CT = 270 pF
VFB = 0.8 V
(Continued)
5
MB3800
(Continued)
Parameter
Symbol
Min
Typ
Max
1.0
1.2
—
V
VOH2
RB = 750 Ω, VCC = 1.8 V
IO = –10 mA
0.8
1.0
—
V
VOL1
RB = 390 Ω, IO = 15 mA
—
0.1
0.2
V
VOL2
RB = 750 Ω, VCC = 1.8 V
IO = 10 mA
—
0.1
0.2
V
Output source current
IO+
RB = 390 Ω, VO = 0.9 V
—
–30
–20
mA
Output sink current
IO–
RB = 390 Ω, VO = 0.3 V
30
60
—
mA
Pull down resistance
RO
20
30
40
kΩ
Pin voltage
VBR
0.2
0.3
0.4
V
Input off condition
IOFF
–20
—
0
µA
Input on condition
ION
—
—
–45
µA
Pin current range
IBR
–1.8
—
–0.1
mA
Stand-by current
ICCS
BR/CTL pin open or VCC
—
—
1
µA
Average supply
current
ICC
RB = 390 Ω
—
5.5
9.3
mA
—
RB = 390 Ω
—
■ DIAGRAM
FB pin voltage
Reference input for short circuit
detection comparator
Idle period setting voltage
Sawtooth wave output
Soft start setting voltage
OUT pin waveforms
SCP pin waveforms
Soft start
tS
ON
Power supply control SW
OFF
6
Unit
RB = 390 Ω, IO = –15 mA
Output section
Entire device
Value
VOH1
Output voltage
Output current
setting section/
Control section
Condition
t PE
Output
short
circuit
Output short circuit
Short circuit
detection
MB3800
■ HOW TO SET THE TIME CONSTANT FOR SOFT START AND SHORT CIRCUIT
DETECTION
1. Soft Start
At power on, the capacitor CPE connected to the SCP pin (pin 2) starts charging. The PWM comparator compares
the soft start setting voltage as a proportion of the voltage at the SCP pin with the sawtooth waveform.
The comparison controls the ON duty of the OUT pin (pin 5), causing the soft start operation. On completion of soft
start operation, the voltage at the SCP pin stays low, the soft start setting voltage stays high, and the circuit enters
the output short circuit detection wait state.
Soft start time (The time until the output ON duty reaches approximately 50%)
tS [s] ≅ 0.35 × CPE [µF]
2. Short Circuit Protection
If the switching regulator output suddenly drops due to load effect, the error amplifier output (FB pin (pin 8)) is fixed
at VOM+ and capacitor CPE starts charging. When the voltage at the SCP pin reaches approximately 0.8 V, the OUT
pin (pin 5) is set low and the SCP pin (pin 2) stays low.
Once the protection circuit operates, the circuit can be restored by resetting the power supply.
• Short circuit detection time
tPE [s] ≅ 0.8 × CPE [µF]
7
MB3800
■ TYPICAL CHARACTERISTICS
Input threshold voltage vs. Supply voltage
T a = +25°C
R B = 390 Ω
10
1.0
Input threshold voltage V T (V)
Average supply current I CC (mA)
Average supply current vs. Supply voltage
8
6
4
2
0
0
4
8
12
16
0.8
0.6
0.4
0.2
0
20
T a = +25°C
4
0
Input threshold voltage vs. Supply voltage
0.8
0.6
0.4
0.2
0
High level output voltage V OUT (V)
T a = +25°C
0
1.0
2.0
3.0
4.0
5.0
10
V CC = 2 V
5
0
–5
–10
–15
–40
–20
0
+20
+40
+60
+80
Low level output
1.6
1.2
0.8
0.4
–10
Input threshold voltage variation ratio vs.
Operating ambient temperature
High level output
V CC = 2 V
R B = 390 Ω
T a = +25°C
0
20
Operating ambient temperature T a (°C)
2.0
0
16
Supply voltage V CC (V)
–20
–30
–40
High level output current IOUT (mA)
–50
Low level output voltage V OUT (mV)
Input threshold voltage V T (V)
1.0
12
Supply voltage V CC (V)
Input threshold voltage variation ratio ∆V T/V T (%)
Supply voltage V CC (V)
8
+100
V CC = 2 V
R B = 390 Ω
T a = +25°C
500
400
300
200
100
0
0
20
40
60
80
100
Low level output current IOUT (mA)
(Continued)
8
MB3800
-50
-40
V CC = 2 V
V OUT = 0.9 V
T a = +25°C
-30
-20
-10
0
0
-0.4
-0.8
-1.2
-1.6
BR/CTL pin input voltage vs. BR/CTL pin input current
BR/CTL pin input voltage V BR (mV)
Output source current IOUT (mA)
Output source current vs. BR/CTL pin input current
500
400
300
200
100
0
-2.0
V CC = 2 V
T a = +25°C
0
BR/CTL pin input current I BR (mA)
-0.8
-0.4
-1.2
-1.6
-2.0
BR/CTL pin input current I BR (mA)
Oscillation frequency vs.Timing resistor
Average supply current vs. BR/CTL pin input current
5.0
V CC = 2 V
T a = +25°C
Oscillation frequency f OSC (Hz)
Average supply current I CC (mA)
1M
4.0
3.0
2.0
1.0
0
0
-40
-20
-60
-80
500 k
200 k
100 k
C T = 1000 pF
50 k
20 k
C T = 10000 pF
10 k
5k
2k
1k
-100
BR/CTL pin input current I BR (µA)
10 k
5k
20 k
Frequency variation ratio vs. Operating ambient temperature
10
10
C T = 270 pF
R T = 3.0 kΩ
Ta = +25°C
5
Frequency variation ratio ∆f/f (%)
Frequency variation ratio ∆f/f (%)
2k
Timing resistor R T (Ω)
Frequency variation ratio vs. Supply voltage
0
-5
-10
-15
V CC = 2 V
T a = +25°C
C T = 100 pF
0
2
4
6
8
10
12
Supply voltage V CC (V)
14
16
V CC = 2 V
C T = 270 pF
R T = 3.0 kΩ
5
0
-5
-10
-15
-40
-20
0
+20
+40
+60
+80 +100
Operating ambient temperature T a (°C)
(Continued)
9
MB3800
(Continued)
Maximum duty cycle vs. Oscillation frequency
V CC = 2 V
C T = 270 pF
Ta = +25°C
Maximum duty cycle t DUTY (%)
100
80
60
40
20
0
10 k
100 k
1M
Oscillation frequency f OSC (Hz)
Output pin voltage and current waveforms
(reference data)
2V
(V)
6
V CC = 2 V
C T = 270 pF
R T = 1.0 kΩ
4
V OUT
2
0
(mA)
50
I OUT
0
–50
10 mV
0
200 ns
0.4
0.8
1.2
1.6
2.0 t(µs)
Note: The OFF delay time of V OUT depends on the
characteristics of the external transistor.
Measurement circuit diagram
V CC
(5 V)
22 µH
18 kΩ
MB3800
5
I OUT
+
V OUT 10 µF
4
2 kΩ
390 Ω
–IN
10
MB3800
■ FUNCTIONAL DESCRIPTION
1. Switching Regulator Function
(1) Reference voltage circuit
The reference voltage circuit generates a temperature-compensated reference voltage (≅1.25V) from voltage
supplied from the VCC pin (pin 3). In addition to providing the reference voltage for the switching regulator, the circuit
also sets the idle period.
(2) Sawtooth wave oscillator
The sawtooth oscillator generates a sawtooth wave (up to 1 MHz) that is stable with respect to the supply voltage
and temperature. The capacitor and resistor that set the oscillation frequency are connected to the OSC pin (pin 7).
(3) Error amplifier (Error Amp)
The error amplifier detects the output voltage of the switching regulator and outputs the PWM control signal. The
voltage gain is fixed, and connecting a phase compensation capacitor to the FB pin (pin 8) provides stable phase
compensation for the system.
(4) PWM comparator (PWM Comp.)
The voltage comparator has one inverting and three non-inverting inputs. The comparator is a voltage/pulse width
converter that controls the ON time of the output pulse depending on the input voltage. The output level is high (H)
when the sawtooth wave is lower than the error amplifier output voltage, soft start setting voltage, and idle period
setting voltage.
(5) Output circuit
The output circuit has a totem pole type configuration and can drive an external NPN transistor directly. The value
of the ON/OFF current can be set by a resistor connected to the BR/CTL pin (pin 4).
2. Power Supply Control Function
Stand-by mode (supply current 1 µA or less) can be set by connecting the BR/CTL pin (pin 4) to VCC or by making
the pin open circuit.
SW
Mode
OFF
Stand-by mode
ON
Operating mode
MB3800
4
BR/CTL
RB
SW
11
MB3800
3. Other Functions
(1) Soft start and short circuit detection
Soft start operation is set by connecting capacitor CPE to the SCP pin (pin 2). Soft start prevents a current spike on
start-up.
On completion of soft start operation, the SCP pin (pin 2) stays low and enters the short circuit detection wait state.
When an output short circuit occurs, the error amplifier output is fixed at VOM+ and capacitor CPE starts charging.
After charging to approximately 0.8 V, the OUT pin (pin 5) is set low and the SCP pin (pin 2) stays low.
Once the protection circuit operates, the circuit can be restored by resetting the power supply. (See “■ HOW TO
SET THE TIME CONSTANT FOR SOFT START AND SHORT CIRCUIT DETECTION”.)
(2) Circuit to prevent malfunction at low input voltage
Transients when powering on or instantaneous glitches in the supply voltage can lead to malfunction of the control
IC and cause system damage or failure. The circuit to prevent malfunction at low input voltage detects a low input
voltage by comparing the supply voltage to the internal reference voltage. On detection, the circuit fixes the OUT
pin (pin 5) to low.
The system recovers when the supply voltage rises back above the threshold voltage of the malfunction prevention
circuit.
■ APPLICATION EXAMPLE
18 kΩ
22 µH
ÐIN
SCP
V in
(3 V)
1
8
2
7
FB
OSC
+
MB3800
+
V CC
3
6
BR/CTL
4
0.1 µF
5
33 µF
390 Ω
2 kΩ
GND
OUT
0.1 µF
270 pF
3 kΩ
CTL
12
Vo
(5 V)
10 µF
MB3800
■ NOTES ON USE
• Take account of common impedance when designing the earth line on a printed wiring board.
• Take measures against static electricity.
- For semiconductors, use antistatic or conductive containers.
- When storing or carrying a printed circuit board after chip mounting, put it in a conductive bag or container.
- The work table, tools and measuring instruments must be grounded.
- The worker must put on a grounding device containing 250 kΩ to 1 MΩ resistors in series.
• Do not apply a negative voltage
- Applying a negative voltage of −0.3 V or less to an LSI may generate a parasitic transistor, resulting in
malfunction.
■ ORDERING INFORMATION
Part number
Package
Remarks
MB3800PF-❏❏❏
8-pin Plastic SOP
(FPT-8P-M01)
Conventional version
MB3800PNF-❏❏❏
8-pin Plastic SOP
(FPT-8P-M02)
Conventional version
MB3800PFV-❏❏❏
8-pin Plastic SSOP
(FPT-8P-M03)
Conventional version
MB3800PF-❏❏❏E1
8-pin Plastic SOP
(FPT-8P-M01)
Lead Free version
MB3800PNF-❏❏❏E1
8-pin Plastic SOP
(FPT-8P-M02)
Lead Free version
MB3800PFV-❏❏❏E1
8-pin Plastic SSOP
(FPT-8P-M03)
Lead Free version
■ RoHS Compliance Information of Lead (Pb) Free version
The LSI products of Fujitsu Microelectronics with “E1” are compliant with RoHS Directive , and has observed
the standard of lead, cadmium, mercury, Hexavalent chromium, polybrominated biphenyls (PBB) , and polybrominated diphenyl ethers (PBDE) .
The product that conforms to this standard is added “E1” at the end of the part number.
13
MB3800
■ MARKING FORMAT (Lead Free version)
3800
Lead Free version
E1XXXX
XXX
SOP-8
(FPT-8P-M01)
INDEX
3800
XXXX
E1 XXX
Lead Free version
3800
Lead Free version
1 XXX
XXX
INDEX
14
SOP-8
(FPT-8P-M02)
SSOP-8
(FPT-8P-M03)
MB3800
■ LABELING SAMPLE (Lead free version)
lead-free mark
JEITA logo
MB123456P - 789 - GE1
(3N) 1MB123456P-789-GE1
1000
(3N)2 1561190005 107210
JEDEC logo
G
Pb
QC PASS
PCS
1,000
MB123456P - 789 - GE1
2006/03/01
ASSEMBLED IN JAPAN
MB123456P - 789 - GE1
1/1
0605 - Z01A
1000
1561190005
Lead Free version
15
MB3800
■ MB3800PF-❏❏❏E1, MB3800PNF-❏❏❏E1, MB3800PFV-❏❏❏E1
RECOMMENDED CONDITIONS of MOISTURE SENSITIVITY LEVEL
Item
Condition
Mounting Method
IR (infrared reflow) , Manual soldering (partial heating method)
Mounting times
2 times
Storage period
Before opening
Please use it within two years after
Manufacture.
From opening to the 2nd
reflow
Less than 8 days
When the storage period after
opening was exceeded
Please processes within 8 days
after baking (125 °C, 24H)
5 °C to 30 °C, 70%RH or less (the lowest possible humidity)
Storage conditions
[Temperature Profile for FJ Standard IR Reflow]
(1) IR (infrared reflow)
H rank : 260 °C Max
260 °C
255 °C
170 °C
to
190 °C
(b)
RT
(a)
(a) Temperature Increase gradient
(b) Preliminary heating
(c) Temperature Increase gradient
(d) Actual heating
(d’)
(e) Cooling
(d)
(e)
(d')
: Average 1 °C/s to 4 °C/s
: Temperature 170 °C to 190 °C, 60s to 180s
: Average 1 °C/s to 4 °C/s
: Temperature 260 °C Max; 255 °C or more, 10s or less
: Temperature 230 °C or more, 40s or less
or
Temperature 225 °C or more, 60s or less
or
Temperature 220 °C or more, 80s or less
: Natural cooling or forced cooling
Note : Temperature : the top of the package body
(2) Manual soldering (partial heating method)
Conditions : Temperature 400 °C Max
Times
: 5 s max/pin
16
(c)
MB3800
■ PACKAGE DIMENSIONS
8-pin plastic SOP
(FPT-8P-M01)
8-pin plastic SOP
(FPT-8P-M01)
Lead pitch
1.27 mm
Package width ×
package length
5.3 × 6.35 mm
Lead shape
Gullwing
Sealing method
Plastic mold
Mounting height
2.25 mm MAX
Weight
0.10 g
Code
(Reference)
P-SOP8-5.3×6.35-1.27
Note 1) *1 : These dimensions include resin protrusion.
Note 2) *2 : These dimensions do not include resin protrusion.
Note 3) Pins width and pins thickness include plating thickness.
Note 4) Pins width do not include tie bar cutting remainder.
+0.25
+.010
+0.03
*1 6.35 –0.20 .250 –.008
0.17 –0.04
+.001
8
.007 –.002
5
*2 5.30±0.30 7.80±0.40
(.209±.012) (.307±.016)
INDEX
Details of "A" part
+0.25
2.00 –0.15
+.010
.079 –.006
1
1.27(.050)
"A"
4
0.47±0.08
(.019±.003)
0.13(.005)
(Mounting height)
0.25(.010)
0~8˚
M
0.50±0.20
(.020±.008)
0.60±0.15
(.024±.006)
+0.10
0.10 –0.05
+.004
.004 –.002
(Stand off)
0.10(.004)
C
2002 FUJITSU LIMITED F08002S-c-6-7
Dimensions in mm (inches).
Note: The values in parentheses are reference values.
(Continued)
17
MB3800
8-pin plastic SOP
Lead pitch
1.27 mm
Package width ×
package length
3.9 × 5.05 mm
Lead shape
Gullwing
Sealing method
Plastic mold
Mounting height
1.75 mm MAX
Weight
0.06 g
(FPT-8P-M02)
8-pin plastic SOP
(FPT-8P-M02)
+0.25
Note 1) *1 : These dimensions include resin protrusion.
Note 2) *2 : These dimensions do not include resin protrusion.
Note 3) Pins width and pins thickness include plating thickness.
Note 4) Pins width do not include tie bar cutting remainder.
+.010
+0.03
*1 5.05 –0.20 .199 –.008
0.22 –0.07
+.001
.009 –.003
8
5
*2 3.90±0.30 6.00±0.40
(.154±.012) (.236±.016)
Details of "A" part
45˚
1.55±0.20
(Mounting height)
(.061±.008)
0.25(.010)
0.40(.016)
1
"A"
4
1.27(.050)
0.44±0.08
(.017±.003)
0.13(.005)
0~8˚
M
0.50±0.20
(.020±.008)
0.60±0.15
(.024±.006)
0.15±0.10
(.006±.004)
(Stand off)
0.10(.004)
C
2002 FUJITSU LIMITED F08004S-c-4-7
Dimensions in mm (inches).
Note: The values in parentheses are reference values.
(Continued)
18
MB3800
(Continued)
8-pin plastic SSOP
(FPT-8P-M03)
8-pin plastic SSOP
(FPT-8P-M03)
Lead pitch
0.80 mm
Package width ×
package length
4.2 × 3.5 mm
Lead shape
Gullwing
Sealing method
Plastic mold
Mounting height
1.45 mm MAX
Weight
0.04 g
Code
(Reference)
P-SSOP8-4.2×3.5-0.80
Note 1) *1 : Resin protrusion. (Each side : +0.15 (.006) Max).
Note 2) *2 : These dimensions do not include resin protrusion.
Note 3) Pins width and pins thickness include plating thickness.
Note 4) Pins width do not include tie bar cutting remainder.
+0.03
*1 3.50±0.10(.138±.004)
0.17 –0.04
+.001
8
.007 –.002
5
*2 4.20±0.10
6.20±0.20
(.165±.004) (.244±.008)
INDEX
Details of "A" part
+0.20
1.25 –0.10
+.008
.049 –.004
(Mounting height)
0.25(.010)
1
"A"
4
0.80(.031)
0.37±0.08
(.015±.003)
0.10(.004)
0~8˚
M
0.50±0.20
(.020±.008)
0.60±0.15
(.024±.006)
0.10±0.10
(.004±.004)
(Stand off)
0.10(.004)
C
2002 FUJITSU LIMITED F08005S-c-3-5
Dimensions in mm (inches).
Note: The values in parentheses are reference values.
19
FUJITSU MICROELECTRONICS LIMITED
Shinjuku Dai-Ichi Seimei Bldg. 7-1, Nishishinjuku 2-chome, Shinjuku-ku,
Tokyo 163-0722, Japan
Tel: +81-3-5322-3347 Fax: +81-3-5322-3387
http://jp.fujitsu.com/fml/en/
For further information please contact:
North and South America
FUJITSU MICROELECTRONICS AMERICA, INC.
1250 E. Arques Avenue, M/S 333
Sunnyvale, CA 94085-5401, U.S.A.
Tel: +1-408-737-5600 Fax: +1-408-737-5999
http://www.fma.fujitsu.com/
Asia Pacific
FUJITSU MICROELECTRONICS ASIA PTE LTD.
151 Lorong Chuan, #05-08 New Tech Park,
Singapore 556741
Tel: +65-6281-0770 Fax: +65-6281-0220
http://www.fujitsu.com/sg/services/micro/semiconductor/
Europe
FUJITSU MICROELECTRONICS EUROPE GmbH
Pittlerstrasse 47, 63225 Langen,
Germany
Tel: +49-6103-690-0 Fax: +49-6103-690-122
http://emea.fujitsu.com/microelectronics/
FUJITSU MICROELECTRONICS SHANGHAI CO., LTD.
Rm.3102, Bund Center, No.222 Yan An Road(E),
Shanghai 200002, China
Tel: +86-21-6335-1560 Fax: +86-21-6335-1605
http://cn.fujitsu.com/fmc/
Korea
FUJITSU MICROELECTRONICS KOREA LTD.
206 KOSMO TOWER, 1002 Daechi-Dong,
Kangnam-Gu,Seoul 135-280
Korea
Tel: +82-2-3484-7100 Fax: +82-2-3484-7111
http://www.fmk.fujitsu.com/
FUJITSU MICROELECTRONICS PACIFIC ASIA LTD.
10/F., World Commerce Centre, 11 Canton Road
Tsimshatsui, Kowloon
Hong Kong
Tel: +852-2377-0226 Fax: +852-2376-3269
http://cn.fujitsu.com/fmc/tw
All Rights Reserved.
The contents of this document are subject to change without notice.
Customers are advised to consult with sales representatives before ordering.
The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose
of reference to show examples of operations and uses of FUJITSU MICROELECTRONICS device; FUJITSU MICROELECTRONICS
does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information.
FUJITSU MICROELECTRONICS assumes no liability for any damages whatsoever arising out of the use of the information.
Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use
or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU MICROELECTRONICS
or any third party or does FUJITSU MICROELECTRONICS warrant non-infringement of any third-party's intellectual property right or
other right by using such information. FUJITSU MICROELECTRONICS assumes no liability for any infringement of the intellectual
property rights or other rights of third parties which would result from the use of information contained herein.
The products described in this document are designed, developed and manufactured as contemplated for general use, including without
limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured
as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect
to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in
nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in
weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite).
Please note that FUJITSU MICROELECTRONICS will not be liable against you and/or any third party for any claims or damages arising
in connection with above-mentioned uses of the products.
Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by
incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current
levels and other abnormal operating conditions.
Exportation/release of any products described in this document may require necessary procedures in accordance with the regulations of
the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws.
The company names and brand names herein are the trademarks or registered trademarks of their respective owners.
Edited
Strategic Business Development Dept.