SE1509-L

SPECIFICATION FOR APPROVAL
REF. :
SE1509□□□□L□-□□□
ABC'S DWG NO.
PROD.
Shielded SMD Power Inductor
NAME
REV.
20130506-A
PAGE
1
Ⅰ﹒Configuration and dimensions:
C
1R2
B
A
1
E
2.80 ref.
2.80 ref.
2
15.60 ref.
3.20 ref.
5.5
4.40 ref.
9.20 ref.
8.60 ref.
1
F
D
3
(PCB Pattern)
Unit:m/m
A
B
C
D
E
F
15.0±0.40
15.0±0.40
9.50±0.50
7.80±0.50
4.00±0.25
10.00 ref.
Ⅱ﹒Schematic diagram:
1
2
3
Ⅲ﹒Description:
a﹒Ferrite ER core construction.
b﹒Magnetically shielded.
c﹒Enamelled copper wire:F class
Peak Temp:245℃ max.
Max. Peak Temp - 5℃:30sec max.
Max time above 217℃ :60sec~150sec max.
d﹒Product weight: 7.35g(ref.)
Temperature
Rising Area
e﹒Moisture sensitivity Level 1
f﹒Products comply with RoHS' requirements
AR-001C
Reflow Area
Forced Cooling Area
+3.0℃ / sec max. -(1.0 ~ 5.0)℃ / sec max.
Peak Temperature:
245℃
217℃
Temperature ( ℃ )
a•Storage temp. : -40℃~ +125℃
b•Operating temp. : -40℃ ~ +125℃
( Temp. rise included )
c﹒Resistance to solder heat :245℃,10 sec.
150 ~ 200℃ / 60 ~ 120sec
250
g﹒Halogen free available
Ⅳ﹒General specification:
Preheat Area
+4.0℃ / sec max.
60sec~150sec
200
60sec max.
150
60sec~120sec
100
50
0
50
100
150
Time ( seconds )
200
250
SPECIFICATION FOR APPROVAL
REF. :
SE1509□□□□L□-□□□
ABC'S DWG NO.
PROD.
Shielded SMD Power Inductor
NAME
REV.
20130506-A
PAGE
Ⅴ﹒Electrical characteristics:
DWG. No.
Inductance
(uH)
SE15091R2ML□-□□□
SE15091R4ML□-□□□
SE15091R8ML□-□□□
SE15092R0ML□-□□□
SE15092R5ML□-□□□
SE15092R8ML□-□□□
SE15093R0ML□-□□□
SE15093R6ML□-□□□
SE15093R9ML□-□□□
SE15094R5ML□-□□□
SE15094R8ML□-□□□
SE15095R6ML□-□□□
1.20±20%
1.40±20%
1.80±20%
2.00±20%
2.50±20%
2.80±20%
3.00±20%
3.60±20%
3.90±20%
4.50±20%
4.80±20%
5.60±20%
1).
2). "-
:Packaging information:
Code
□□□":Reference code
RDC
(mΩ)
max.
2.0
2.0
3.0
3.0
3.4
3.4
4.3
4.3
6.5
6.5
7.2
7.2
Irms (A)
(△T=40℃ max.)
max.
16.0
15.0
14.0
13.0
12.0
12.0
10.0
10.0
9.0
8.0
7.0
6.0
Isat (A)
(△L/L0A=20%)
typ.
19.0
18.0
18.0
16.0
14.5
14.0
13.0
12.0
11.5
10.5
10.0
9.0
5). Inductance Test Freq.:100KHz / 1V
6). Isat base on △L/L0A=20% typ.
3). Electrical specifications at 25℃
4). Irms base on temp. rise at 40℃ max.& inductance drop 10% max.
@ Inductance VS. DC Superposition Characteristics
6.0
5R6
5.0
4R5
Inductance ( uH )
4.0
3.0
3R0
2.0
2R0
1R2
1.0
0
AR-001C
5
10
15
DC Current ( A )
20
25
2
SPECIFICATION FOR APPROVAL
REF. :
SE1509□□□□L□-□□□
ABC'S DWG NO.
PROD.
Shielded SMD Power Inductor
NAME
REV.
20130506-A
PAGE
3
Ⅵ﹒Packaging information:
( 1 ) Configuration
T
Cover Tape
A
B
N
2.0±0.5
∮C
∮C
D
G
Embossed carrier
※Carrier tape width : D
P:24 m/m
4 m/m
Start
End
1R2
1R2
1R2
Leader
no component
200 m/m min.
Trailer
no component
400 m/m min.
Components
User direction of feed
( 2 ) Dimensions
Unit:m/m
Style
A
13 - 32
330
B
21±0.8
C
D
13
32
G
34
+0
N
100
-0
T
38.4
( 3 ) Q'TY & G.W. Per package
Inner : Reel
Code
B
AR-001C
Outer : Carton
Q'TY (pcs)
G.W. (gw)
Style
Q'TY (pcs)
G.W. (Kg)
Size (cm)
200
1370
13 - 32
800
6.8
38 x 37 x 22
SPECIFICATION FOR APPROVAL
REF. :
ABC'S DWG NO.
PROD.
Shielded SMD Power Inductor
NAME
REV.
SE1509□□□□L□-□□□
20130506-A
PAGE
4
Ⅶ﹒Reliability test:
Item
1.High Temperature
Exposure
Reference documents
MIL-STD-202 Method 108
Test Condition
1.Temperature: 125℃
2.Time:96 hours.
1.Temperature: -40℃ ~ 125℃
2.Temperature Cycling JESD22 Method JA-104
2.Number of cycle:96 cycle
3.Dwell time:30 minutes
3.Biased Humidity Test MIL-STD-202 Method 103
1.Temperature: 85±5 ℃
2.Time:96 Hours
3.Humidity: 85±5% RH.
1.Temperature: 125℃
2.Time:96 hours.
3.Apply rated current.
4.Operational Life
MIL-PRF-27
5.Exeternal Visual
MIL-STD-883 Method 2009 constructions, marking and
Inspect product
workmanship.
Test Specification
1.No mechanical and electrical
damage.
2.Inductance shall not change
more than ±25%.
1.No mechanical and electrical
damage.
2.Inductance shall not change
more than ±25%.
1.No mechanical and electrical
damage.
2.Inductance shall not change
more than ±25%.
1.No mechanical and electrical
damage.
2.Inductance shall not change
more than ±25%.
1.No pollution on the surface of
products.
2.Clear marking.
3.No crack.
6.Physical Dimensions JESD22 Method JB-100
Verify physical dimensions to
the applicable product detail
specification.
Per product specification
standard
7.Resistance to solvents MIL-STD-202 Method 215
Immerse into solvent for 3±0.5 minutes &
brush 10 times for therr cycles.
1.No body change in apperarance.
2.No marking blurred.
3.Inductance shall not change
more than ±25%.
8.Vibration Test
MIL-STD-202 Method 204
1.Frequency and Amplitued :
10-2000-10 Hz, 1.5 mm.
2.Direction:X, Y, Z
3.Test duration:2 hours for each direction,
6 hours in total.
1.No mechanical and electrical
damage.
2.Inductance shall not change
more than ±25%.
9.Resistance To
Soldering Heat Test
MIL-STD-202 Method 210
1.Highest temperature: 245±5℃
2.Time(temp.≧ 217℃):60~150 Second.
3.IR reflow times:3 times.
10.Rated current
MIL-STD-202 Method 330
11.Temperature rise
MIL-PRF-27
12.Over load
MIL-PRF-27
1.No mechanical and electrical
damage.
2.Inductance shall not change
more than ±25%.
1.No mechanical and electrical
damage.
Apply rated current for 5 second.
2.Inductance shall not change
more than ±25%.
1.No mechanical and electrical
damage.
Apply rated current for 10 minutes.
2.Inductance shall not change
more than ±25%.
1.No mechanical and electrical
damage.
Apply twice as rated current for 5 minutes.
(It's not application to some special design) 2.Inductance shall not change
more than ±25%.
1.Baking in pre-testing:
155±5℃ / 16Hours±30 min.
2.Peak temperature:240±5℃
3.Time(temp.≧217℃):60~150 second.
4.IR reflow times:1 times.
The terminal shall be at least 95%
covered with fresh solder.
User Spec.
1.Operating temperature: -40℃~125℃
2.Room temperature:25℃.
1.No mechanical and electrical
damage.
2.Inductance shall not change
more than ±25%.
MIL-STD-202 Method 201
1.DV:500V
2.Time:1minutes
16.Drop
JESD22-B111
Packaged & Drop down from 1m.In 1 angle
1ridges & 2 surfaces orientation.
17.Terminal Strength
Test
JIS-C-6429
1.Apply push force to samples
mounted on PCB.
2.Force of 1.8 kg for 60±1 seconds.
13.Solderability Test
14.Electrical
Characteriazation
15.Withstanding
Voltage Test
AR-001C
J-STD-002
1.During the test no breakdown.
2.The characteristic is normal after test.
1.No case deformation or change in
appearance.
2.Inductance shall not change
more than ±25%.
After test, inductors shall be no
mechanical damage.