Available at Digi-Key** www.digikey.com 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 High Precision TCXO / VCTCXO Oscillators Description: Features: The Connor-Winfield’s T100/T200 and the TV100/TV200 series have very high frequency stability with excellent phase noise performance. Available in a 5x7mm surface mount package. These TCXO's and VCTCXO's through the use of Analog Temperature Compensation are capable of holding sub 100-ppb or 200-ppb stabilities over the commercial or industrial temperature ranges. The surface mount package is designed for highdensity mounting and is optimum for mass production. Models: T100 / T200-Series TV100 / TV200-Series •Package T100-T200 Series 5 x 7mm 10 Pad TV100-TV200 Series 5 x 7mm 4 Pad •Frequencies Available: 10, 12.8, 19.2, 20.0, 24.576 or 40.0 MHz •3.3 Vdc Operation •Output Logic: LVCMOS •Frequency Stability: T100 / TV100: +/-100 ppb, 0 to 70°C T200 / TV200: +/-200 ppb, -40 to 85°C •Fixed Frequency - TCXO •Optional Control Voltage - VCTCXO •Low Jitter <0.50 ps RMS •Low Phase Noise •Tri-State Enable/Disable: Available on T100 / T200 Models. •Tape and Reel Packaging •RoHS Compliant / Lead Free T2 00 20 V 12 .0 MH 41 Z Applications: Basestation, Communications,DSL / ADSL, Femtocell, IP Timing, LTE, Precision GPS, SONET / SDH, WiMAX / WiBro, WLAN. Absolute Maximum Ratings Parameter Minimum Nominal Maximum Units Storage Temperature Supply Voltage (Vcc) Input Voltage -40 -0.5 (Vc) - - -0.5- 85 4.6 Vcc + 0.5 °C Vdc Vdc ** T200 & TV200 not available at Digi-Key Ordering Information T Type / Package TCXO / VCTCXO Series T = 5.0x7.0 mm 10 Pads TV = 5.0x7.0 mm 4 Pads 200 V Frequency Stability and Temperature Range TCXO or VCTCXO 100 = ±100 ppb, 0 to 70°C 200 = ±200 ppb, -40 to 85°C Supply Voltage = 3.3 Vdc Output Logic = LVCMOS F = TCXO V = VCTCXO Notes - 20.0M Output Frequency Frequency Format -xxx.xM Min -xxx.xxxxxxM Max *Amount of numbers after the decimal point. M = MHz Example: Part Number Bulletin Page Revision Date Tx350 1 of 6 05 02 April 2015 T100F-019.2M = 5x7mm 10 pad package, ±100 ppb, 0 to 70°C, 3.3 Vdc, LVCMOS Output, TCXO, 19.2 MHz T200V-020.0M = 5x7mm 10 pad package, ±200 ppb, -40 to 85°C, 3.3 Vdc, LVCMOS Output, VCTCXO, 20.0 MHz TV100F-010.0M = 5x7mm 4 pad package, ±100 ppb, 0 to 70°C, 3.3 Vdc, LVCMOS Output, TCXO, 10.0 MHz TV200V-012.8M = 5x7mm 4 pad package, ±200 ppb, -40 to 85°C, 3.3 Vdc, LVCMOS Output, VCTCXO, 12.8 MHz 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Operating Specifications Parameter Minimum Nominal Maximum Output Frequency (Fo)10.0, 12.8, 19.2, 20.0, 24.576 and 40.0M Frequency Calibration @ 25 °C -1.0 - 1.0 Frequency Stability (See Ordering Information for full part number) Model T100x, TV100x -100 - 100 Model T200x, TV200x -200 - 200 Frequency vs. Load Stability -0.20 - 0.20 Frequency vs. Voltage Stability -0.20 - 0.20 Static Temperature Hysteresis - - 0.40 Freq. shift after reflow soldering -1.0 - 1.0 Long Term Stability -1.0 - 1.0 Aging per Life (20 Years) -3.0 - 3.0 per Day -40 - 40 per Second - 4.63E-13 Operating Temperature Range(See Ordering Information for full part number) Model T100x, TV100x 0 - 70 Model T200x, TV200x -40 - 85 Units Notes MHz ppm 1 ppb ppb ppm ppm ppm ppm ppm 2 2 ±5% ±5% 3 4 5 ppm ppb °C °C Supply Voltage (Vcc) 3.135 3.30 3.465 Vdc Supply Current (Icc) - - 2.1 mA Jitter: Period Jitter - 3.0 5.0 ps RMS Integrated Phase Jitter (12K to 20M) - 0.3 1.0 ps RMS 6 SSB Phase Noise for Fo=10.0 MHz @ 1 Hz offset - -60 - dBc/Hz @ 10 Hz offset - -98 - dBc/Hz @ 100 Hz offset - -126 - dBc/Hz @ 1 KHz offset - -143 - dBc/Hz @ 10 KHz offset - -151 - dBc/Hz @ 100 KHz offset - -152 - dBc/Hz @ 1 MHz offset - -155 - dBc/Hz Start-Up Time - - 10 ms Control Voltage Input Characteristics Parameter Minimum Control Voltage 0.3 Frequency Pullability ±10 Control Voltage Slope Monotonic Linearity - Input Impedance 100K Modulation Bandwidth (3dB) 10 Nominal Maximum Units Notes 1.65 3.0 V - - ppm Positive Slope - 10 % - - Ohm - - KHz Bulletin Page Revision Date Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches. © Copyright 2015 The Connor-Winfield Corporation Not intended for life support applications. Tx350 2 of 6 05 02 April 2015 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Enable /Disable Input Characteristics (Pad 8) (Models T100F, T200F, T100V and T200V Only) Parameter Enable Input Voltage -(Vih) Disable Input Voltage - (Vil) Function Minimum 70%Vcc - Nominal - - Maximum - 30%Vcc Units Vdc Vdc Notes 7 7 Output Low: High or Open: Disabled (High Impedance) Enabled LVCMOS Output Characteristics Parameter Load (CL) Voltage (High) (Voh) (Low) (Vol) Duty Cycle at 50% of Vcc Rise / Fall Time 10% to 90% Minimum Nominal Maximum Units Notes - 90%Vcc - 45 - 15 - - 50 4 - - 10%Vcc 55 8 pF Vdc Vdc % ns 8 Package Characteristics Package Hermetically sealed ceramic package with grounded metal cover Environmental Characteristics Vibration: Shock: Soldering Process: Vibration per Mil Std 883E Method 2007.3 Test Condition A. Mechanical Shock per Mil Std 883E Method 2002.4 Test Condition B. RoHS compliant lead free. See soldering profile on page 2. Notes: 1.Initial calibration @ 25°C. ±2°C, for VCTCXO's Vc = 1.65V. Specifications at time of shipment after 48 hours of operation. 2.Frequency stability vs. change in temperature. [±(Fmax-Fmin)/2.Fo]. For VCTCXO's - Vc -= 1.65V 3.Frequency change after reciprocal temperature ramped over the operating range. Frequency measured before and after at 25°C 4.Two consecutive reflows after 1 hour recovery @ 25°C. 5.Frequency drift over 1 year @ 25°C. 6.BW = 12 KHz to Fo/2 MHz 7.Leave Pad 8 on models, T100F, T200F, T100V, T200V unconnected if enable / disable function is not required. When tri-stated, the output stage is disabled but the oscillator and compensation circuit are still active (current consumption < 1 mA). 8.Attention: To achieve optimal frequency stability, and in some cases to meet the specification stated on this data sheet, it is required that the circuit connected to this TCXO output must have the equivalent input capacitance that is specified by the nominal load capacitance. Deviations from the nominal load capacitance will have a graduated effect on the stability of approximately 20 ppb per pF load difference. Bulletin Page Revision Date Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches. © Copyright 2015 The Connor-Winfield Corporation Not intended for life support applications. Tx350 3 of 6 05 02 April 2015 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com T100/T200 Package Outline T100/T200 Suggested Pad Layout 0.079 Max. (2.0mm) 0.276 ±0.006 (7.0mm) 0.295 (7.49mm) 0.051 (1.28mm) 0.030 (0.76mm) Keep Out Area 0.197 ±0.006 (5.0mm) T200V 1241 20.0 MHZ 8 0.215 (5.46mm) 0.025(6 Places) (0.635mm) Pin 1 1 0.030 (0.762mm) (4 Places) 2 3 10 4 9 7 5 Top View 10 4 1 2 0.051 (1.28mm) 3 0.040 (1.02mm) (6 Places) 5 8 6 0.100 (2.54mm) Bottom View 0.038 (0.965mm) (4 Places) 7 9 0.037 (0.94mm) 6 Dimensional Tolerance: ±.005 (.127mm) ±.02 (.508mm) 0.100 (2.54mm) * Do not route any traces in the keep out area. It is recommended the next layer under the keep out area is to be ground plane. T100/T200 Pad Connections 1: 2: 3: 4: 5: 6: 7: 8: 9: 10: Do Not Connect Do Not Connect Do Not Connect Ground Output Do Not Connect Do Not Connect Enable / Disable Supply Voltage (Vcc VCTCXO: Control Voltage (Vc) TCXO: N/C T100/T200 Series Alternate Package Outline 0.095 (2.4mm) 0.276 ±0.006 (7.0mm) 0.197 ±0.006 (5.0mm) T200 1434 24.576 MHZ TV100/TV200 Package Outline 0.276 ±0.006 (7.0mm) Alternate package applies to all part numbers with output frequency of 24.576 MHz. The differences are the top view crystal size, and the overall height. Bottom view, suggested pad layout, and pad connections all remain the same as above. TV100/TV200 Suggested Pad Layout 0.079 Max. (2.0mm) 0.071 (1.8mm) 4 Places 4 TV100F 1241 10.0 MHZ 1 0.034 (0.90mm) (4 Places) 0.165 (4.2mm) (Top View) Pad 1 0.047 (1.2mm) 4 Places (Top View) 2 Dimensional Tolerance: ±.005 (.127mm) ±.02 (.508mm) (Bottom View) 4 3 0.197 ±0.006 (5.0mm) 3 0.055 (1.40mm) (4 Places) 1 0.224 (5.7mm) 2 TV100/TV200 Pad Connections 1: 2: 3: 4: VCTCXO: Voltage Control (Vc) TCXO: N/C Ground Output Supply (Vcc) Keep Out * Area * Do not route any traces in the keep out area. It is recommended the next layer under the keep out area is to be ground plane. Bulletin Page Revision Date Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches. © Copyright 2015 The Connor-Winfield Corporation Not intended for life support applications. Tx350 4 of 6 05 02 April 2015 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com T100 / T200 Design Recommendations Vcc, should have a large copper area for reduced inductance. Connect a 0.01uF bypass capacitor <0.1”(2.54mm) from the pad. 8 6 5 9 1 3 Ground, should have a large copper area for reduced inductance. Top View 50 Ohm trace <1”by design Vcc 0.010”(0.254mm) Recommended clearance inductance for internal copper flood. 4 10 T100 / T200 Test Circuit Enable/ Disable DNC DNC Buffer Vcc Supply Voltage Ground Top View 8 7 6 9 5 Ground 4 10 1 2 Output Ground 3 15 pF 0.1 uF Bypass OSC 10 nF Bypass 50 Ohm Trace Without Output Vias Buffer TCXO = N/C VCTCXO = Vc DNC DNC DNC DNC = Do Not Connect TOP LAYER GROUND LAYER ....... BOTTOM LAYER TV100 / TV200 Design Recommendations Vcc, should have a large copper area for reduced inductance. Connect a 0.01uF bypass capacitor <0.1”(2.54mm) from the pad. 4 3 9 5 10 4 1 2 Top View 0.010”(0.254mm) Recommended clearance inductance for internal copper flood. TV100 / TV200 Test Circuit 50 Ohm trace <1”by design Vcc Buffer Ground Ground, should have a large copper area for reduced inductance. Vcc Supply Voltage 3 1 2 Output Ground Top View Ground 15 pF 0.1 uF Bypass OSC 4 10 nF Bypass TCXO = N/C VCTCXO = Vc 50 Ohm Trace Without Output Vias Buffer TOP LAYER GROUND LAYER ....... BOTTOM LAYER Attention: To achieve optimal frequency stability, and in some cases to meet the specification stated on this data sheet, it is required that the circuit connected to this TCXO output must have the equivalent input capacitance that is specified by the nominal load capacitance. Deviations from the nominal load capacitance will have a graduated effect on the stability of approximately 20 ppb per pF load difference. Bulletin Page Revision Date Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches. © Copyright 2015 The Connor-Winfield Corporation Not intended for life support applications. Tx350 5 of 6 05 02 April 2015 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com LVCMOS Output Waveform Phase Noise Information 1V/Div Solder Profile Temperature 260°C 5x7 mm Tape and Reel Information 260°C 220°C 180°C 150°C 120°C 1 0 10 s Up to 120 s 60 to 90 s Typical Typical Meets IPC/JEDEC J-STD-020C Revision History Revision A00 A01 02 03 04 05 Date 12/05/11 04/24/12 04/26/12 10/12/12 01/09/13 02/04/15 Changes Advanced information data sheet released Added 12.8 MHz and +/-50ppb 0 to 70°C Models Updated integrated phase jitter to 0.3 ps RMS nominal. Removed M series Updated phase noise information Updated to 24.576 MHz and 40.0 MHz Frequencies Bulletin Page Revision Date Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches. © Copyright 2015 The Connor-Winfield Corporation Not intended for life support applications. Tx350 6 of 6 05 02 April 2015