Available at Digi-Key** www.digikey.com 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 Telecom Performance 5x7mm TCXO / VCTCXO T / TV Series Description: Features: Connor-Winfield's Txxx and TVxxx series are TV 50 10 4 14 5x7mm TCXO and .0 MH 07 Z VCTCXO products with exceptional frequency stability and low phase noise. Through the use of analog temperature compensation, these products are capable of holding Stratum 3 level temperature stabilities of ±0.28 ppm over the commercial and industrial temperature ranges. Available in 4-pad or 10-pad surface mount footprints. These products are designed for such applications as IEEE 1588 PTP and Synchronous Ethernet. All models will meet ±4.6 ppm accuracies for twenty years •Frequency Stabilities Available: +/-0.28 ppm (6.4 to 49.152 MHz) +/-0.50 ppm (6.4 to 49.152 MHz) +/-1.00 ppm or +/-2.00 ppm (6.4 to 54 MHz) •Temperature Ranges Available: 0 to 85°C, 0 to 70°C, -40 to 85°C or -20 to 70°C Packages Available: •T - Series: 5 x 7mm - 10 Pad •TV - Series: 5 x 7mm - 4 Pad •3.3 Vdc Operation •Output Logic: LVCMOS or Clipped Sinewave •Fixed Frequency - TCXO •Voltage Controlled - VCTCXO •Low Jitter <0.50 ps RMS •Low Phase Noise •Tri-State Enable/Disable: (T Model Series Only) •Tape and Reel Packaging •RoHS Compliant / Lead Free Applications: •IEEE 1588 Applications •Synchronous Ethernet slave clocks, ITU-T G.8262 EEC options 1 & 2 •Compliant to Stratum 3, GR-1244-CORE & GR-253-CORE •Wireless Communications •Small Cells •Test and Measurement •GPS Standard Frequencies Available * * 6.4, 9.72, 10, 10.24, 12.5, 12.8, 13.5, 19.2, 19.44, 20, 20.48, 25, 27, 38.88 MHz Available frequencies from the factory for small quantity orders or quick delivery. Additional frequencies are available. Alternate package outline for select part numbers 38MHz to 52MHz ** Not all Models available at Digi-Key TV Type / Package TCXO / VCTCXO Series T = 5.0x7.0 mm 10 Pads TV = 5.0x7.0 mm 4 Pads Ordering Information 5 Temperature Range 3 = 0 to 85 °C 5 = 0 to 70°C 6 = -40 to 85°C 7 = -20 to 70°C 0 4 - 010.0M Frequency Stability Features Output Frequency 0 = ±0.28 ppm 1 = ±0.50 ppm 2 = ±1.00 ppm 3 = ±2.00 ppm 2 = TCXO, LVCMOS, 3.3 Vdc 3 = TCXO, Clipped Sinewave, 3.3 Vdc 4 = VCTCXO, LVCMOS, 3.3 Vdc 5 = VCTCXO, Clipped Sinewave, 3.3 Vdc Frequency Format -xxx.xM Min -xxx.xxxxxxM Max *Amount of numbers after the decimal point. M = MHz Example: Part Number Bulletin Page Revision Date Tx176 1 of 6 19 01 April 2015 TV504-010.0M = 5x7mm 4 pad package, ±0.28 ppm, 0 to 70°C, 3.3 Vdc, LVCMOS Output, VCTCXO T715-012.8M = 5x7mm 10 pad package, ±0.50 ppm, -20 to 70°C, 3.3 Vdc, Clipped Sinewave Output, VCTCXO T522-050.0M = 5x7mm 10 pad package, ±1.0 ppm, 0 to 70°C, 3.3 Vdc, LVCMOS Output, TCXO TV602-010.0M = 5x7mm 4 pad package, ±0.28 ppm, -40 to 85°C, 3.3 Vdc, LVCMOS Output, TCXO 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Absolute Maximum Ratings Parameter Storage Temperature Supply Voltage (Vcc) Input Voltage Minimum -55 -0.5 -0.5 Nominal - - - Maximum 95 6.0 Vcc + 0.5 Units °C Vdc Vdc Notes Operating Specifications Parameter Minimum Nominal Maximum Units Notes Output Frequency (Fo) Models Tx0x, TVx0x 6.4 - 49.152 MHz Models Tx1x, TVx1x 6.4 - 49.152 MHz Models Tx2x, TVx2x 6.4 - 54 MHz Models Tx3x, TVx3x 6.4 - 54 MHz Operating Temperature Range(See Ordering Information for full part number) Models T3xx, TV3xx 0 - 85 °C Models T5xx, TV5xx 0 - 70 °C Models T6xx, TV6xx -40 - 85 °C Models T7xx, TV7xx -20 - 70 °C Frequency Calibration @ 25 °C -1.0 - 1.0 ppm 1 Frequency Stability (See Ordering Information for full part number) Per STRATUM 3 GR-1244-CORE Frequency Stability ±0.28 ppm is only available in the frequency range of 6.4 to 49.152 MHz. Models Tx0x, TVx0x -0.28 - 0.28 ppm 2 Holdover Stability -0.32 - 0.32 ppm 3 Constant Temperature Stability -40 - 40 ppb Over 24 Hrs. Frequency Stability (See Ordering Information for full part number) Models Tx1x, TVx1x -0.50 - 0.50 ppm 2 Models Tx2x, TVx2x -1.00 - 1.00 ppm 2 Models Tx3x, TVx3x -2.00 - 2.00 ppm 2 Frequency vs. Load Stability -0.05 - 0.05 ppm ±5% Frequency vs. Voltage Stability -0.05 - 0.05 ppm ±5% Static Temperature Hysteresis - - 0.40 ppm 4 Freq. shift after reflow soldering -1.0 - 1.0 ppm 5 Long Term Stability -1.0 - 1.0 ppm 6 Aging per Life (20 Years) -3.0 - 3.0 ppm per Day -40 - 40 ppb Total Frequency Tolerance -4.6 - 4.6 ppm 7 Supply Voltage (Vcc) 3.135 3.30 3.465 Vdc Supply Current (Icc) LVCMOS - 2.1 6.0 mA Clipped Sinewave - 1.3 2.9 mA Jitter: Period Jitter - 3.0 5.0 ps RMS Integrated Phase Jitter (12K to Fo/2) - 0.3 1.0 ps RMS 8 Allan Deviation (1s) - 1.0E-10 Typical SSB Phase Noise For Fo 10.0 MHz 25.0 MHz 50.0 MHz @ 10 Hz offset -98 -90 -73 dBc/Hz @ 100 Hz offset -125 -120 -103 dBc/Hz @ 1 KHz offset -143 -140 -134 dBc/Hz @ 10 KHz offset -151 -151 -151 dBc/Hz @ 100 KHz offset -152 -152 -152 dBc/Hz @ 1 MHz offset -155 -154 -154 dBc/Hz Start-Up Time - - 10 ms Bulletin Page Revision Date Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches. © Copyright 2015 The Connor-Winfield Corporation Not intended for life support applications. Tx176 2 of 6 19 01 April 2015 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Control Voltage Input Characteristics Parameter Minimum Control Voltage 0.3 Frequency Pullability ±10 Pull Slope (Vc=1.65V) - Control Voltage Slope Monotonic Linearity - Input Impedance 100K Modulation Bandwidth (3dB) 10 Nominal Maximum Units 1.65 3.0 V ±12 - ppm 8.00 - ppm/V Positive Slope - 5 % - - Ohm - - Notes KHz OE Enable /Disable Input Characteristics (Pad 8) T Series only Parameter Enable Input Voltage -(Vih) Disable Input Voltage - (Vil) Function Nominal - - Maximum - 30%Vcc Units Vdc Vdc Notes 9 9 Maximum Units Notes - - 10%Vcc - 4 55 8 pF Vdc Vdc mA mA % ns 10 Units Notes Output Low: High or Open: Disabled (High Impedance) Enabled LVCMOS Output Characteristics Minimum Nominal Parameter Load (CL) Voltage (High) (Voh) (Low) (Vol) Current(High) (Ioh) (Low) (Iol) Duty Cycle at 50% of Vcc Rise / Fall Time 10% to 90% Parameter Minimum 70%Vcc - - 90%Vcc - -4 - 45 - 15 - - - - 50 4 Clipped Sinewave Output Characteristics Minimum Nominal Maximum Load (RC) Output Load Resistance - 10K - Ohm Output Load Capacitance - 10 - pF OutputVoltage (< 40 MHz) 1.0 1.2 - V OutputVoltage (=>40 MHz) 0.8 1.0 - V Output Impedance - 200 - Ohms 11 12 pk-pk pk-pk Package Characteristics Package Hermetically sealed ceramic package with grounded metal cover Environmental Characteristics Vibration: Vibration per Mil Std 883E Method 2007.3 Test Condition A. Shock: Mechanical Shock per Mil Std 883E Method 2002.4 Test Condition B. Soldering Process: RoHS compliant lead free. See soldering profile on page 6. Notes: 1. Initial calibration @ 25°C. ±2°C, for VCTCXO's Vc = 1.65V. Specifications at time of shipment 2. Frequency stability vs. change in temperature. [±(Fmax-Fmin)/(2*Fo]). For VCTCXO's - Vc -= 1.65V 3. Inclusive of frequency stability, supply voltage change (±1%), aging, for 24 hours. Per STRATUM 3 GR-1244-CORE. 4. Frequency change after reciprocal temperature ramped over the operating range. Frequency measured before and after at 25°C 5. Two consecutive solder reflows after 1 hour recovery @ 25°C. 6. Frequency drift over 1 year @ 25°C. 7. Inclusive of calibration @ 25°C, frequency vs. change in temperature, change in supply voltage (±5%), load change (±5%), reflow soldering process and 20 years aging. 8. BW = 12 KHz to 20 MHz 9. Leave Pad 8 on the T Series unconnected if enable / disable function is not required. When tri-stated, the output stage is disabled but the oscillator and compensation circuit are still active (current consumption < 1 mA). 10. Attention: To achieve optimal frequency stability, and in some cases to meet the specification stated on this data sheet, it is required that the circuit connected to this TCXO output must have the equivalent input capacitance that is specified by the nominal load capacitance. Deviations from the nominal load capacitance will have a graduated effect on the stability of approximately 20 ppb per pF load difference. 11. Load components are required for proper operation of the device. 12. Output is AC coupled. Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches. © Copyright 2015 The Connor-Winfield Corporation Not intended for life support applications. Bulletin Page Revision Date Tx176 3 of 6 19 01 April 2015 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com T Series Package Outline T Series Suggested Pad Layout 0.079 Max. (2.0mm) 0.276 ±0.006 (7.0mm) 0.295 (7.49mm) 0.051 (1.28mm) 0.030 (0.76mm) Keep Out Area 0.197 ±0.006 (5.0mm) T715 1407 12.8 MHZ 8 0.037 (0.94mm) 0.215 (5.46mm) 0.025(6 Places) (0.635mm) Pin 1 1 2 Top View 10 4 2 0.051 (1.28mm) 3 0.040 (1.02mm) (6 Places) 4 0.030 (0.762mm) (4 Places) 6 5 1 3 10 7 9 0.100 (2.54mm) Bottom View 9 5 8 0.038 (0.965mm) (4 Places) 7 6 Dimensional Tolerance: ±.005 (.127mm) ±.02 (.508mm) 0.100 (2.54mm) * Do not route any traces in the keep out area. It is recommended the next layer under the keep out area is to be ground plane. T Series Pad Connections 1:Do Not Connect 2:Do Not Connect 3:Do Not Connect 4:Ground 5:Output 6:Do Not Connect 7:Do Not Connect 8:Enable / Disable (OE) 9:Supply Voltage (Vcc 10:VCTCXO: Control Voltage (Vc) TCXO: N/C T Series Alternate Package Outline 0.095 (2.4mm) 0.276 ±0.006 (7.0mm) 0.197 ±0.006 (5.0mm) T602 1434 40.0MHZ TV Series Package Outline 0.276 ±0.006 (7.0mm) 3 0.047 (1.2mm) 4 Places (Top View) 2 (Bottom View) 4 4 0.165 (4.2mm) Dimensional Tolerance: ±.005 (.127mm) ±.02 (.508mm) 3 0.055 (1.40mm) (4 Places) TV Series Pad Connections 0.071 (1.8mm) 4 Places 0.197 ±0.006 (5.0mm) (Top View) 1 0.034 (0.90mm) (4 Places) TV Series Suggested Pad Layout 0.079 Max. (2.0mm) TV504 1407 10.0 MHZ Pad 1 Alternate package applies to select part numbers in the 38 to 52MHz frequency range. The differences are the top view crystal size, and the overall height. Bottom view, suggested pad layout, and pad connections all remain the same as above. 1 0.224 (5.7mm) 2 Keep Out * Area * Do not route any traces in the keep out area. It is recommended the next layer under the keep out area is to be ground plane. 1: 2: 3: 4: VCTCXO: Voltage Control (Vc) TCXO: N/C Ground Output Supply (Vcc) Bulletin Page Revision Date Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches. © Copyright 2015 The Connor-Winfield Corporation Not intended for life support applications. Tx176 4 of 6 19 01 April 2015 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com T Series Design Recommendations Vcc, should have a large copper area for reduced inductance. Connect a 0.01uF bypass capacitor <0.1”(2.54mm) from the pad. 8 6 5 9 Buffer 4 10 1 3 Top View Vcc, should have a large copper area for reduced inductance. Connect a 0.01uF bypass capacitor <0.1”(2.54mm) from the pad. 50 Ohm trace <1”by design Vcc 0.010”(0.254mm) Recommended clearance inductance for internal copper flood. TV Series Design Recommendations 3 5 1 Top View 2 Top View Ground 50 Ohm Trace Without Output Vias Buffer OSC 50 Ohm trace <1”by design Vcc Buffer Ground 4 10 Ground Ground, should have a large copper area for reduced inductance. 4 9 0.010”(0.254mm) Recommended clearance inductance for internal copper flood. Ground, should have a large copper area for reduced inductance. OSC Top View Ground 50 Ohm Trace Without Output Vias Buffer TOP LAYER GROUND LAYER ....... ....... TOP LAYER GROUND LAYER BOTTOM LAYER BOTTOM LAYER T Series LVCMOS Test Circuit TV Series LVCMOS Test Circuit LVCMOS Output Waveform Enable/ Disable DNC DNC Vcc Supply Voltage 8 7 Vcc Supply Voltage 6 9 5 15 pF 0.1 uF Bypass 15 pF 10 nF Bypass TCXO = N/C VCTCXO = Vc DNC 2 Ground 3 2 1 0.1 uF Bypass Ground 1 4 10 Output 3 4 Output 10 nF Bypass TCXO = N/C VCTCXO = Vc DNC DNC DNC = Do Not Connect 1V/Div T Series Clipped Sinewave Test Circuit TV Series Clipped Sinewave Test Circuit Clipped Sinewave Output Waveform Enable/ Disable DNC DNC Vcc Supply Voltage 8 7 6 9 5 4 10 1 2 Output 10 nF Bypass TCXO = N/C VCTCXO = Vc DNC 4 Output 3 Ground Ground 1 2 0 3 10 pF 0.1 uF Bypass Vcc Supply Voltage 10K Ohm 10 pF 0.1 uF Bypass DNC DNC 10 nF Bypass 10K Ohm TCXO = N/C VCTCXO = Vc DNC = Do Not Connect 200 mV/Div Note: The clipped sinewave output is AC coupled Bulletin Page Revision Date Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches. © Copyright 2015 The Connor-Winfield Corporation Not intended for life support applications. Tx176 5 of 6 19 01 April 2015 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Phase Noise Information TIE Model TV504-010.0MHz TV504-010.0M: WANDER GENERATION IN A STRATUM 3 PLL AT 0.098 Hz BANDWIDTH MTIE TDEV TV504-010.0M: MTIE per GR-253-CORE TV504-010.0M: TDEV per GR-253-CORE 5x7mm Tape and Reel Information Solder Profile Temperature 260°C 260°C 220°C 180°C 150°C 1 120°C 0 10 s Up to 120 s 60 to 90 s Typical Typical Revision History Revision 17 18 Date 02/11/14 09/15/14 Action Updated specifications and combined the T and TV series data sheets. Added Alternate Package Outline Meets IPC/JEDEC J-STD-020C Bulletin Page Revision Date Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches. © Copyright 2015 The Connor-Winfield Corporation Not intended for life support applications. Tx176 6 of 6 19 01 April 2015