5x7mm Precision TCXO In Stock at Digi-Key Description: 2111 Comprehensive Drive 2111 Comprehensive Drive Aurora, Illinois 60505 Aurora, Illinois 60505 Phone: 630- 851- 4722 Phone: 630- 851- 4722 Fax: 630- 851- 5040 Fax: 630- 851- 5040 www.conwin.com www.conwin.com US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 Features: Model: D75J The Connor-Winfield’s D75J is a 5x7mm Surface Mount Temperature Compensated Crystal Controlled Oscillator (TCXO) with a Tri-State LVCMOS output. Through the use of Analog Temperature Compensation, the D75J is capable of holding sub 1-ppm stabilities over the 0 to 70°C temperature range. 3.3 Vdc Operation LVCMOS Output Frequency Stability: ± 1.0 ppm Temperature Range: 0 to 70°C Low Jitter <1ps RMS Tri-State Enable/Disable Function 5x7mm Surface Mount Package Tape and Reel Packaging RoHS Compliant / Pb Free D7 38 5J 11 .88 4 MH 4 Z Absolute Maximum Ratings Parameter Storage Temperature Supply Voltage (Vcc) Input Voltage Minimum Nominal Maximum Units -55 -0.5 -0.5 - - - 85 6.0 Vcc+0.5 °C Vdc Vdc Maximum Units Notes Operating Specifications Parameter Nominal Frequency (Fo) Frequency Calibration @ 25 °C Frequency Stability vs. Temperature Frequency vs. Load Stability Frequency vs. Voltage Stability Static Temperature Hysteresis Aging Operating Temperature Range: Supply Voltage (Vcc) Supply Current (Icc) Period Jitter Integrated Phase Jitter SSB Phase Noise at 10Hz offset SSB Phase Noise at 100Hz offset SSB Phase Noise at 1KHz offset SSB Phase Noise at 10KHz offset SSB Phase Noise at 100KHz offset Start-up Time Minimum Nominal - -1.0 -1.0 -0.2 -0.2 - -1.0 0 3.135 - - - - - - - - - 38.88, 40.0 or 50.0 - - - - - - - 3.3 - 3 0.5 -70 -100 -120 -140 -145 - - 1.0 1.0 0.2 0.2 0.4 1.0 70 3.465 6 5 1.0 - - - - - 5 Notes MHz ppm 1 ppm 2 ppm ±5% ppm ±5% ppm 3 ppm/year °C Vdc ±5% mA ps rms ps rms 4 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz ms Enable / Disable Input Characteristics (Pad 8) Parameter Minimum Enable Voltage (High) Disable Voltage (Low) Nominal Maximum 70%Vcc - - - 30%Vcc Units Notes Vdc Vdc 5 5 LVCMOS Output Characteristics Parameter Load Voltage (High) (Voh) (Low) (Vol) Duty Cycle at 50% of Vcc Rise / Fall Time 10% to 90% Minimum Nominal Maximum - 90%Vcc - 45 - 15 - - 50 - - - 10%Vcc 55 8 Units Notes pF Vdc Vdc % ns 6 Package Characteristics Package Vibration: Shock: Soldering Process; Hermetically sealed crystal mounted on a ceramic package Environmental Characteristics Vibration per Mil Std 883E Method 2007.3 Test Condition A Mechanical Shock per Mil Std 883E Method 2002.4 Test Condition B. RoHS compliant lead free. See soldering profile on page 2. Ordering Information D75J-038.88M*, D75J-040.0M* or D75J-050.0M* * For the tape and reel option, add -T to the end of the part number. Example: D75J-038.88M-T Notes: Bulletin Page Revision Date Tx238 1 of 2 03 15 Nov 2011 1. Initial calibration @ 25°C. Specifications at time of shipment after 48 hours of operation. 2. Frequency stability vs. change in temperature. [±(Fmax - Fmin)/2.Fo]. 3. Frequency change after reciprocal temperature ramped over the operating range. Frequency measured before and after at 25°C. 4. BW = 12 KHz to 20 MHz. 5. Leave Pad 8 unconnected if enable / disable function is not required. When tri-stated, the output stage is disabled but the oscillator and compensation circuit are still active (current consumption < 1 mA). 6. For best performance it is recommended that the circuit connected to this output should have an equivalent input capacitance of 15pF. Specifications subject to change without notice. All dimensions in inches. © Copyright 2011 The Connor-Winfield Corporation 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Package Layout Suggested Pad Layout 0.079 Max. (2.0mm) 0.276 ±0.006 (7.0mm) 0.295 (7.49mm) Keep Out Area 8 0.025(6 Places) (0.635mm) 1 0.030 (0.762mm) (4 Places) 2 10 4 260°C 220°C 180°C 150°C 120°C 0 10 s Up to 120 s 60 to 90 s Typical Typical Meets IPC/JEDEC J-STD-020C 9 10 4 1 2 3 0.051 (1.28mm) 5 8 0.038 (0.965mm) (4 Places) 5 0.100 (2.54mm) Bottom View Temperature 260°C 6 Top View 0.215 (5.46mm) 0.040 (1.02mm) (6 Places) 3 7 9 0.037 (0.94mm) Pin 1 1: 2: 3: 4: 5: 6: 7: 8: 9: 10: 0.051 (1.28mm) 0.030 (0.76mm) 0.197 ±0.006 (5.0mm) D75J 1144 38.88 MHZ Pad Connections 7 6 Dimensional Tolerance: ±.005 (.127mm) ±.02 (.508mm) 0.100 (2.54mm) * Do not route any traces in the keep out area. It is recommended the next layer under the keep out area is to be ground plane. Design Recommendations Vcc, should have a large copper area for reduced inductance. Connect a 0.01uF bypass capacitor <0.1”(2.54mm) from the pad. 8 5 10 4 1 3 Ground, should have a large copper area for reduced inductance. Top View OSC Output Waveform 50 Ohm trace <1”by design Vcc 0.010”(0.254mm) Recommended clearance inductance for internal copper flood. 6 9 Do Not Connect Do Not Connect Do Not Connect Ground Output Do Not Connect Do Not Connect Tri-State Enable / Disable Supply Voltage Vcc N/C Buffer Ground Top View Ground Test Circuit 50 Ohm Trace Without Output Vias Buffer DNC TOP LAYER GROUND LAYER 1 ....... N/C DNC DNC 2 3 10 4 9 5 Ground Vcc Supply Voltage BOTTOM LAYER Attention: To achieve optimal frequency stability, and in some cases to meet the specification stated on this data sheet, it is required that the circuit connected to this TCXO output must have the equivalent input capacitance that is specified by the nominal load capacitance. Deviations from the nominal load capacitance will have a graduated effect on the stability of approximately 20 ppb per pF load difference. 8 7 Output 6 15 pF 0.1 uF Bypass Enable/ DNC DNC Disable 10 nF Bypass DNC = Do Not Connect Tape and Reel Dimensions Solder Profile Temperature 260°C 260°C PIN 1 220°C 180°C 150°C .69 120°C (17.5mm) 8.46 DIA (216mm DIA) .08 (2.0mm) .31 .08 (7.9mm) (2.0mm) 0 .21 (5.4mm) 9.84 DIA (250mm DIA) .157 (4.0mm) .08 (2.0mm) 3.15 (80mm) .315 (8.0mm) .06 DIA Direction Of Feed (Customer) 10 s Up to 120 s 60 to 90 s Typical Typical Meets IPC/JEDEC J-STD-020C (1.5mm DIA) Bulletin 1.00 DIA (25mm DIA) Page .295 (7.5mm) MEETS EIA-481A and EIAJ-1009B 2,000 PCS/REEL .07 (1.75mm) .83 (16.0mm) Specifications subject to change without notice. All dimensions in inches. © Copyright 2011 The Connor-Winfield Corporation Revision Date Tx238 2 of 2 03 15 Nov 2011