Precision TCXO Model DOT702F 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 Description: Features: The Connor-Winfield's DOT702F is a surface mount, 9x14mm, 3.3V, LVCMOS Temperature Compensated Crystal Oscillator (TCXO) designed for applications requiring very tight frequency stability and low phase noise. The RoHS compliant true surface mount package is designed for high-density mounting and is optimum for mass production. •3.3 Vdc Operation •Frequency Stability: ±0.28 ppm •Temperature Range: -20 to 70°C •LVCMOS Output Logic •9x14mm SMT Package •Tape and Reel Packaging •RoHS Compliant / Pb Free Absolute Maximum Ratings Parameter Storage Temperature Supply Voltage (Vcc) Minimum Nominal Maximum Units -55 -0.5 - - 125 4.5 °C Vdc Notes Absolute Ratings: Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only. The functional operation of the device at those or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to conditions outside the "recommended operating conditions" for any extended period of time may adversely impact device reliability and result in failures not covered by warranty. Operating Specifications Parameter Minimum Frequency (Fo) - Frequency Calibration @ 25 °C -1.0 Frequency Stability -0.28 Aging / Day -10 Aging / First Year -300 Total Frequency Tolerance -4.6 Frequency vs. Load Stability -20 Frequency vs. Voltage Stability -20 Operating Temperature Range: -20 Supply Voltage (Vcc) 3.135 Supply Current - Period Jitter - Integrated Phase Jitter (12 KHz to Fo/2) - Short Term Stability - Page Revision Date TX416 1 of 4 00 25 Sept 2014 Maximum Units 7.3728 - - - - - - - - 3.3 3 3 0.5 - - 1.0 0.28 10 300 4.6 20 20 70 3.465 6 5 1.0 1.0E-9/s MHz ppm ppm ppb ppb ppm ppb ppb °C Vdc mA ps rms ps rms SSB Phase Noise @ 1Hz offset @ 10Hz offset @ 100Hz offset @ 1KHz offset @ 10KHz offset @ 100KHz offset - - - - - - -70 -100 -130 -148 -154 -155 - - - - - - dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz Start-up Time - - 10 ms Notes: Bulletin Nominal 1. Frequency referenced to Fo @ 25°C. 2. Frequency stability vs. change in temperature. [±(Fmax - Fmin)/(2*Fo)]. 3. After 30 days of operation. 4. Inclusive of calibration @25°C, frequency vs. change in temperature, change in supply voltage(±5%), load change(±5%) and 15 years aging. 5. Referenced to 15 pF. Notes 1 2 3 4 ±5%, 5 ±5% ±5% 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com LVCMOS Output Characteristics Parameter Load Output Voltage (High) (Voh) (Low) (Vol) Output Current (Ioh) (Iol) Duty Cycle at 50% of Vcc Rise / Fall Time 10% to 90% Minimum Nominal Maximum Units - 15 - pF 90% Vcc - - - - 10% Vcc Vdc Vdc - -4 45 - - - 50 4 4 - 55 8 mA mA % ns Notes Package Characteristics Package consisting of a FR4 substrate and a Ryton-R4 cover. Water Resistant, non-hermetic seal Soldering Characteristics RoHS compliant lead free. See soldering profile on page 4. Recommended Cleaning Process Wash only in an in-line high pressure wash station that has an air knife and drying capabilities. (Drying temperature range from 85° to 100°C) Environmental Characteristics Shock Sinusoidal Vibration Random Vibration Moisture Marking Permanency 500 G’s 1ms, Half sine, 3 shocks per direction, per MIL- STD 202F, Method 213B Test Condition D. 0.06” D.A. or 10G’s Peak, 10 to 500 Hz, per MIL-STD 202F, Method 204D, Test Condition A. 5.35 G’s rms. 20 to 2000 Hz per MIL-STD-202F, Method 214,Test Condition 1A, 15 minutes each axis. 10 cycles, 95% RH, Per MIL-STD-202F, Method 112. Per MIL-STD-202F, Method 215J. Ordering Information DOT702F - 007.3728M Bulletin Page Revision Date Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches. © Copyright 2014 The Connor-Winfield Corporation Not intended for life support applications. TX416 2 of 4 00 25 Sept 2014 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Package Layout A 0.290 (7.37mm) b L D 4 DNC CL 1344 DOT702F 7.3728MHZ Marking Suggested Pad Layout DNC E CL 0.100 (2.54mm) e Pin 1 Index Top View Side View Side View Symbol A D E A1 L b e Min 6.60 8.89 13.34 - Min 0.260 0.350 0.545 - inches Nom. 0.265 0.355 0.550 0.062 0.060 0.040 0.100 0.060 (1.52mm) 1 0.085 (2.03mm) DNC = Do Not Connect A1 6 Pin 1 ID Bottom View mm Nom. Max. 6.73 6.86 9.02 9.15 13.47 13.60 1.58 1.52 1.02 2.54 - 3 Top 2 5 View Max. 0.270 0.360 0.555 - Keep Out Area Keep Out Area Note: Do not route any traces under the device in the keep out area. Pad Connections Phase Noise Plot 1: 2: 3: 4: 5: 6: N/C Do Not Connect Ground Output Do Not Connect Supply Voltage (Vcc) Output Waveform Test Circuit 1V/Div DNC 10uF to 100 uF 0.01uF Output 2 DNC 15 pF N/C DNC = Do Not Connect Bulletin Page Revision Date Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches. © Copyright 2014 The Connor-Winfield Corporation Not intended for life support applications. TX416 3 of 4 00 25 Sept 2014 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Tape and Reel Dimensions 1330 DOT702F 7.3728MHz SM-MECH42 Solder Profile Temperature 260°C 260°C 220°C 180°C 150°C 120°C 0 10 s Up to 120 s 60 to 90 s Typical Typical Meets IPC/JEDEC J-STD-020C Revision History Revision Date Description 00 09/25/14 Data sheet released. Bulletin Page Revision Date Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches. © Copyright 2014 The Connor-Winfield Corporation Not intended for life support applications. TX416 4 of 4 00 25 Sept 2014