DOCUMENT : RLI00000N REVISION : A1 PAGE : 1 OF 11 SPECIFICATION FOR APPROVAL 1/8W 0816 LOW RESISTNACE CHIP RESISTOR 1. Scope This specification applies to 0.8mm x 1.60mm size 1/8W, fixed metal film chip resistors rectangular type for use in electronic equipment. 2. Type Designation RL0816□ − (1) Where □□□ (2) □ (3) (1) Series No :refer to paragraph 4-1 RL0816T or RL0816S (2) Resistance value: refer to paragraph 4-1 For example— Three digits of number ( 0.1 ≤ R) R10 = 0.1Ω 1R0 = 1.0Ω Four digits of number（R < 0.1Ω） R022 = 0.022Ω (3) Resistance tolerance: F = ± 1% G = ± 2% DOCUMENT : RLI00000N REVISION : A1 PAGE : 2 OF 11 SPECIFICATION FOR APPROVAL 3. Construction and Physical Dimensions L a Dimensions (mm) a Code Letter Single side Structure L 1.60 ± 0.10 1.60 ± 0.10 W 0.80 ± 0.10 0.80 ± 0.10 t 0.50 ± 0.10 0.45 ± 0.10 a 0.20 ± 0.15 0.20 ± 0.15 b 0.20 ± 0.15 0.20 ± 0.15 Double sides Structure W t b b Figure 1-1. Double sides structure (≤ 0.091Ω ) a ③ Protective coat ④ Substrate mass : 2mg (ref.) a W t b Note : ① Resistive clement ② Electrode b Figure 1-2. Single side structure ( > 0.091Ω ) Nickel alloy film plating Sn 100% ( Lead free) Epoxy Resin coating Alumina ceramic DOCUMENT : RLI00000N REVISION : A1 PAGE : 3 OF 11 SPECIFICATION FOR APPROVAL 4. Ratings 4-1 Specification Power Rating* 1/8 W Series No. Resistance Value RL0816T RL0816S 0.015Ω, 0.020Ω ~ 0.091Ω 0.1Ω ~ 6.8Ω ± 1%(F) , ± 2%(G) Resistance Tolerance Note*: Power Rating is based on continuous full load operation at rated ambient temperature of 70℃. For resistors operated at ambient temperature in excess of 70℃, the maximum load shall be derated in accordance with the following curve. % Rated dissipation ratio 100 50 0 -55 70 125 Ambient temperature Figure 2 Derating Curve 4-2 Rated Voltage The rated voltage shall be determined by the following expression. V = P×R Where V：Rated voltage (V) R：Nominal resistance value (Ω) P：Rated dissipation (W) 4-3 Operating and Storage Temperature Range -55 to +125℃ ℃ DOCUMENT : RLI00000N REVISION : A1 PAGE : 4 OF 11 SPECIFICATION FOR APPROVAL 5. Characteristics 5-1 Electrical 5-1-1 Resistance and tolerance Resistance value shall be within the tolerance specified in paragraph 4-1 Refer to IEC 60115-1 Sub-clause 4.5. 5-1-2 Temperature Coefficient of Resistance Not exceed the temperature coefficient of resistance specified in paragraph 4-1 Room temperature → Room temperature + 100℃ Refer to IEC 60115-1 Sub-clause 4.13. 5-1-3 Short Time Overload Resistance Change : ± (0.5%) Without significant damage by flashover (spark ,arching),burning or breakdown etc. Test voltage : 2.5 times the rated voltage. Duration : 5 seconds Refer to IEC 60115-1 Sub-clause 4.13. 5-1-4 Insulation Resistance (1) Between Electrode and Protection Film 100MΩ or over (2) Between Electrode and Substrate 1,000MΩ or over The resistor shall be cramped in the metal block and tested , as shown below. Test voltage : 100 ± 15VDC for 1 minute Refer to IEC 60115-1 Sub-clause 4.6. Pressure Rod (Metal) Insulation Plate Spring Measurement Point A (R0.25mm ~ R0.5mm) Substrate Over coat Film Sample Electrode A B Voltage Supply Metal Block Measurement Point B Substrate Side DOCUMENT : RLI00000N REVISION : A1 PAGE : 5 OF 11 SPECIFICATION FOR APPROVAL 5-1-5 Voltage Proof Resistance Change : ± (0.5%) Without damage by flashover, fire or breakdown, as shown below. The resistor shall be tested as shown in paragraph 4-1-4 The voltage : 100VAC (rms.) for 1 minute Refer to IEC 60115-1 Sub-clause 4.7. 5-2 Mechanical 5-2-1 Terminal Strength Resistance Change : ± (0.5%) Without mechanical damage such as breaks. Electrical characteristics shall be satisfied. If there are electrodes on both surfaces, it shall satisfy the above specifications on whichever surface may be fixated. Bending Amplitude : 3 mm 30 seconds Refer to IEC 60115-1 Sub-clause 4.33. 50 Pressure 20 Amplitude 3 mm Press Jig R230 Refer to EIAJ RC-2530 Test PC Board Sample Solder Supports 45 Within ± 2mm 45 Unit : mm DOCUMENT : RLI00000N REVISION : A1 PAGE : 6 OF 11 SPECIFICATION FOR APPROVAL 5-2-2 Body Strength Resistance Change : ± (0.5%) Without mechanical damage such as breaks. A load of 10N using a R0.5 pressure rod shall be applied to the center in the direction of the arrow and held for 10 ± 1 seconds. Pressure rod R0.5 Resistor 1/2L L Unit : mm 5-2-3 Solderability A new uniform coating of solder shall cover minimum of 95% of the surface being immersed. Temperature of solder : 245 ± 5℃ Immersion duration : 2 ± 0.5 seconds Refer to IEC 60115-1 Sub-clause 4.17. 5-2-4 Resistance to Soldering Heat Resistance Change : ± (0.5%) Electrical characteristics shall be satisfied. Without distinct deformation in appearance. (1) Solder bath method Pre-heat : 100 to 110℃ 30 seconds Temperature : 270 ± 5℃ 10 ± 1seconds (2) Reflow Soldering method Peak temperature : 260 ± 5℃ 10 seconds or less Temperature : 220 ± 5℃ 60 seconds max. The heating apparatus shall be the upper-heated oven and temperature shall be the board surface temperature. (3) Soldering iron method Bit temperature : 350 ± 5℃ 3 ± 1/0 seconds The resistor shall be stored at standard atmospheric conditions for 1 hour, after which the measurements shall be made. Refer to IEC 60115-1 Sub-clause 4.18. DOCUMENT : RLI00000N REVISION : A1 PAGE : 7 OF 11 SPECIFICATION FOR APPROVAL 5-2-5 Resistance to Solvent Without mechanical damage and distinct damage in appearance. Immersion cleaning At normal temperature 300 seconds in Isopropyl Alcohol. Refer to IEC 60115-1 Sub-clause 4.29. 5-3 Endurance 5-3-1 Rapid Change of Temperature Resistance Change : ± (0.5%) Without distinct damage Resistance shall be subjected to 5 cycles of the temperature cycle as following : -55 ± 3℃, 30 minutes→ room temperature, 2 ~ 3 minutes → +125 ± 2℃, 30 minutes → room temperature, 2 ~ 3 minutes Refer to IEC 60115-1 Sub-clause 4.19. 5-3-2 Dump Heat with Load Resistance Change : ± (1.0%) Without distinct damage 60 ± 2℃ with relative humidity of 90 to 95% DC rated voltage for 1.5 hours on 0.5 hour off 1,000 + 48 / - 0 hours 5-3-3 Endurance at 70℃ Resistance Change : ± (1.0%) Without distinct damage 70 ± 2℃ DC rated voltage for 1.5 hours on 0.5 hour off 1,000 + 48 / -0 hours Refer to IEC 60115-1 Sub-clause 4.25. DOCUMENT : RLI00000N REVISION : A1 PAGE : 8 OF 11 SPECIFICATION FOR APPROVAL Mounting of the test sample onto the test board shall be either of following methods. (1) Mounting by solder dipping Epoxy based glue shall be applied in the middle of two lands of the test board. The resistor shall be mounted in such a way that the electrodes of resistors will be evenly placed in the land area and then adhesive resin shall be cured. After applying the Resin Flux with 25 weight % Methyl Alcohol, the board shall be soldered by dipping into a molten solder bath with 260 ± 5℃ for 3 to 5 seconds (2) Mounting by Reflow soldering Solder paste with approximate 200µm thickness shall be applied to the land of test board. The resistor shall be mounted in such way that the electrodes of resistors will be evenly placed in the land area and then shall be soldered under the circumstance that the surface temperature of the board shall be raised 245 ± 5℃(peak temperature) for 5 to 10 seconds in an upper-heater oven. Test Board Material : Glass Fabric Epoxy Resin (Refer to JIS C 6484) Board thickness : 1.6mm Copper foil thickness : 0.035mm (1) Test board A Solder resist b Land 40 c 4.5 f a 100 Unit : mm a b c f 1.0 3.0 1.2 (2.0) DOCUMENT : RLI00000N REVISION : A1 PAGE : 9 OF 11 SPECIFICATION FOR APPROVAL (2) Test board B ( For another test ) 27.0 18.5 8.5 5.3 6.94 1.00 4.00 2.4 0.40 4.46 5.08 1.32 (5.08x9=45.72) 1.22 58.5 Unit : mm DOCUMENT : RLI00000N REVISION : A1 PAGE : 10 OF 11 SPECIFICATION FOR APPROVAL 6. Packaging 6-1 Dimensions 6-1-1 Tape packaging dimensions +- 1.5 0.6 ± 0.05 0.1 0.0 4.0 ± 0.1 Sprocket hole 2.0 ± 0.05 A 3.5 ± 0.05 B 0.65 ± 0.1 1.75 ± 0.1 8.0 ± 0.3 4.0 ± 0.1 Carries cavity Pull Direction ※Pre.emptied holes：75 holes (or 30cm) or more Code Letter A B Dimension 1.1 ± 0.1 1.9 ± 0.1 6-1-2 Reel Dimensions Unit : mm SPECIFICATION FOR APPROVAL 6-2 Peel force of top cover tape The peel speed shall be about 300 mm/min. The peel force of top cover tape shall be between 0.1 to 0.7 N. Top Cover Tape 165 ~ 180° 0.1~0.7 N 6-3 Numbers of taping 5,000 pieces/reel 6-4 Label marking The following items shall be marked on single of the reel. (1) (2) (3) (4) Type designation . Quantity Manufacturing date code Manufacturer’s name (5) The country of origin (6) Shipping number (7) Identification showing lead free products. 6-5 Note Manufactured by our joint company. ( Susumu Co., Ltd. ) DOCUMENT : RLI00000N REVISION : A1 PAGE : 11 OF 11