English User`s Manual

USER GUIDE
Single or 3-Phase True RMS 1000A Power
Clamp Meter with Non-Contact Voltage Detector and
PC interface
Model PQ2071
Introduction
Congratulations on your purchase of the Extech PQ2071 1/3-Phase CAT IV True RMS 1000A
Power Clamp Meter. The PQ2071 measures AC Current, Frequency, Temperature (Type K), and
Power (True Power, Apparent Power, Reactive Power, and Active Power). The PQ2071 also
includes a built-in non-contact Voltage Detector with LED alert. The USB PC interface offers storage
and recall (manually) of up to 99 sets of readings data. Proper use and care of this meter will
provide many years of reliable service. Please visit the Extech Instruments website
(www.extech.com) to check for the latest version of this User Guide and for Product Registration.
Safety
International Safety Symbols
This symbol, adjacent to another symbol or terminal, indicates the user must refer to the
manual for further information.
This symbol, adjacent to a terminal, indicates that, under normal use, hazardous voltages
may be present
Double insulation
This User Guide includes information concerning safety and cautions. Please read the information
carefully and observe all of the Warnings and Notes.
To avoid electric shock or personal injury, read the “Safety Information” and “Rules for Safe
Operation” carefully before using the Meter.
This device is a three phase handheld digital power clamp meter which has both the features of a
digital current meter and also a power measurement meter.
Unpacking Inspection
Check that the following items were included in the packaging. Please report missing or damaged
items to the point of purchase.
Item
Description
Qty
1
User Guide
1 piece
2
Colored Test Leads
3 pieces
3
Black Test Lead
1 piece
4
Colored Alligator Clips
3 pieces
5
Black Alligator Clip
1 piece
6
USB Interface Cable
1 piece
7
Software
1 piece
8
Storage case
1 piece
9
9V Battery
1 piece
2
PQ2071-en-GB_V1.3 7/15
General Safety Information
This Meter complies with the IEC61010 standard for pollution degree 2, overvoltage category (CAT
III 1000V, CAT IV 600V), and double insulation.
Use the Meter only as specified in this operating manual, otherwise the protection provided by the
Meter may be impaired.
In this manual, a Warning identifies conditions and actions that pose hazards to the user, or may
damage the Meter or the equipment under test. A Note identifies general safety information that the
user must observe.
Rules for Safe Operation
Warning
To avoid possible electric shock or personal injury, and to avoid possible damage to the Meter or to
the equipment under test, adhere to the following rules:


















Before using the Meter inspect the meter housing. Do not use the Meter if the housing is
damaged, open, or removed. Look for cracks or missing plastic. Pay particular attention to the
insulation around the connectors.
Inspect the test leads for damaged insulation or exposed metal. Replace damaged test leads
(identical model number or electrical specifications) before using Meter.
Do not apply more than the rated voltage as specified on the Meter.
When measurements have been completed, disconnect the connection between the test
leads and the circuit under test, remove the testing leads from the input terminals of the Meter
and turn the Meter power off.
To avoid electrical shock, do not attempt measurements while the Meter’s housing and / or
battery door is opened.
When the effective voltage exceeds 30VAC, special care should be taken while measuring as
a shock hazard exists at this voltage level.
Use the proper terminals and functions for the measurement in question.
Do not use or store the Meter in an environment of high temperature, humidity, explosive,
inflammable or one with a strong magnetic field.
Do not use the Meter if the meter is wet or if the user’s hands are wet.
When using the test leads, keep fingers behind the finger guards.
Replace the battery as soon as the battery indicator appears. With a low battery, the Meter
may produce false readings that can mislead the user and cause electric shock and personal
injury.
When opening the battery door, ensure that the Meter power is OFF.
When servicing the Meter, use only the same model number or identical electrical
specifications when acquiring replacement parts.
The internal circuit of the Meter must not be tampered with. Tampering with the internal
circuitry can cause meter damage and personal injury.
A soft cloth and a mild detergent should be used to clean the surface of the Meter when
servicing. Do not use abrasives or solvents when cleaning the meter; doing so can cause
corrosion, damage and can potentially compromise the meter’s safety features.
The Meter is suitable for indoor use only.
Turn the Meter off when it is not in use and remove the battery when the meter is to be stored
or unused for long periods.
Keep track of the battery age and replace batteries when necessary. Leaking batteries can
damage the meter.
3
PQ2071-en-GB_V1.3 7/15
Description
Meter Description (front)
1
Transformer Jaw
2
Jaw Open Trigger
3
LCD Display
4
Voltage detector sensor
5
Voltage detector alarm light
6
Function dial switch (HOLD button)
7
Push-buttons (see list below)
8
L1, L2, L3 Input Terminal
9
PC Interface cable jack
Note:
Battery compartment located on back of instrument
Figure 1
4
PQ2071-en-GB_V1.3 7/15
Display icons Description
USB
PC Interface
L1
Phase 1
L2
Phase 2
L3
Phase 3
h
Hours
m
Minutes
S
Seconds
PF
Power Factor
KVA
Active power
KWh
Kilowatt hours
Hz
Frequency(Hertz)
PG
Phase angle
KVAr
ΣW
Figure 2
Reactive power
Sum of Wattage measurements
Low Battery
MAX-MIN
Maximum and Minimum readings
Analog Bar Graph
CLR
̶
Clear Data
Negative symbol
High voltage symbol
AC
AC voltage or current
RCL
Recall stored data
MEM
Data storage
FULL
Data logger is full
HOLD
Data hold is active
5
PQ2071-en-GB_V1.3 7/15
Push-button Description
Figure 3
L1-L2-L3
Press L1-L2-L3 to step through the first phase, second phase, third phase, and the
sum of the watt measurements.
Press and hold L1-L2-L3 for at least two (2) seconds to enter 3P3W mode.
MR
Press once to enter the Memory Recall mode, the MR icon will appear and the meter
will beep. Use the arrow buttons as described directly below to step through the 99reading internal memory.
Σ
In the Active power mode (kW dial position), the Σ button is used to sum the multiple
measurements when testing 3 phase systems. Refer to the Active Power
Measurement section of this User Guide for details on using the sum button.
Press the backlight button to switch the backlight ON. The backlight will
automatically switch OFF after 20 seconds. Press the button to turn the backlight off
manually.
MAX-MIN
Press to view the highest (MAX) reading; press again to view the lowest (MIN)
reading. This feature applies to voltage, current, active power and apparent power
ranges only. While the MAX or MIN icon is displayed, only the highest or lowest
reading is shown.
SAVE
Press SAVE momentarily to store a single reading; the Meter will beep. The index
number shown on the left side of the secondary display will increase with each
stored reading. The maximum number of data points is 99. The Meter displays the
FULL icon when the memory is filled.
USB
Measurement data will be sent to the PC when meter is connected to the PC and the
supplied software and driver is installed and running.
CLEAR
In the Active Energy mode, press and hold CLEAR for at least one (1) second to restart the elapsed timer from zero.
For all other ranges, press and hold CLEAR for at least one (1) second to clear
(erase) the 99-reading internal memory.
▼/▲
When stepping through the sum of power measurements, use the ▼/▲ buttons to
switch the display from active power/reactive power to power factor/apparent power
modes.
In the MR mode, use ▼/▲ to scroll through the meter’s internal 99 reading
memory.
HOLD
Press HOLD to enter the Hold mode, the H will appear and the Meter will beep and
the displayed reading will freeze. Press HOLD again to exit the Hold mode, the
Meter will beep and the H icon will switch off.
6
PQ2071-en-GB_V1.3 7/15
Operation
NOTES: Read and understand all Warning and Caution statements in this operation manual prior
to using this meter. Set the function switch to the OFF position when the meter is not in use.
Non-Contact Voltage Detector
WARNING: Risk of electrocution. Before use, always test the voltage detector on a known live
circuit to verify proper operation.
1.
Rotate the function switch to any measurement position.
2.
Place the detector probe tip on the conductor or voltage source to be
tested.
3.
The red LED light on the front of the meter (just below the clamp jaw)
will illuminate when voltage is detected.
Note: The conductors in electrical cord sets are often twisted. For best
results, move the probe tip along a length of the cord to assure placing the
tip close to the live conductor.
Note: The detector is highly sensitivity. Static electricity or other sources of
energy may randomly trip the sensor. This is normal operation.
7
Figure 4
PQ2071-en-GB_V1.3 7/15
AC Voltage Measurements
AC voltage on Main Display (Frequency on Secondary Display)
The AC Voltage ranges are: 100V, 400V and 750V
The frequency range is: 50Hz~60Hz
1
Single phase - connect the L1 test lead to the
power wire and connect the COM lead to the
neutral wire.
2
L1
L2
L3
3
3-Phase 4-wire - connect the COM lead to the
neutral conductor.
3-Phase 3-Wire - connect the COM lead to an
earth ground.
COM
COM
1.
Insert the black test lead into the meter’s
COM input terminal.
2.
Connect the other end of the black
(COM) test lead to the corresponding
neutral wire (single phase and 3P4W) or
for a 3P3W to one of the phase wires.
3.
Single phase: Insert a test lead into L1
and connect it to the Power wire.
Figure 5 (3P4W)
3Φ4Wire: Connect all 3 leads (red -L1), yellowL2, and blue-L3) into the L1, L2, & L3 meter
input terminals and connect each to a corresponding phase wire. (see fig 5)
3Φ3Wire: Connect L1 and L3 to the meter and then connect L1 to one phase wire and L3 to
the remaining phase wire.
4.
Turn the rotary function switch to the VAC position to select Voltage + Frequency mode.
5.
Press the L1-L2-L3 button to select the appropriate phase, the display shows the
corresponding phase symbol on the display. L1 is the first (single) phase, L2 is the second
phase, and L3 is the third phase.
6.
The main display indicates the True RMS voltage and the secondary display indicates the
Frequency value.
7.
To monitor the highest (MAX) and lowest (MIN) readings, press the MAX-MIN button. The
LCD will now display ‘MAX’ and the meter will indicate only the maximum AC voltage True
RMS value.
8.
Press MAX-MIN again and the LCD will display ‘MIN’ and the meter will indicate only the
minimum AC voltage True RMS value.
9.
Press MAX-MIN again to exit the MAX-MIN mode and return to displaying the real-time AC
voltage True RMS value.
10. The display indicates ‘OL’ when the input voltage is greater than 750V rms.
Note: When the measurement session has been completed, disconnect the test leads from the
circuit under test and remove the test leads from the meter’s input terminals.
8
PQ2071-en-GB_V1.3 7/15
AC Current Measurements
Important Clamp Measurement Considerations
Place the conductor under test at the center of the transformer jaw for the best measurement
accuracy. This meter can only measure one conductor at a time. Do not clamp two or more
conductors. Clamp the wire so that the FACE of the meter is towards the source of power.
To measure AC Current, connect the meter as follows:
1.
Set the Rotary switch to the AAC.
2.
Clamp around one conductor.
3.
The dual display indicates the AC current True
RMS value (main display)
Note: if the voltage leads are connected, the
TRMS AC voltage value will be displayed on the
secondary display.
4.
To monitor the highest (MAX) and lowest (MIN)
readings, press the MAX-MIN button. The LCD
will now display ‘MAX’ and the meter will indicate
5.
only the maximum TRMS AC Current value.
Press MAX-MIN again and the LCD will display
‘MIN’ and the meter will indicate only the
minimum TRMS AC Current value.
Figure 6
6.
Press MAX-MIN again to exit the MAX-MIN mode and
return to displaying the real-time TRMS AC Current value.
7.
The display indicates ‘OL’ when the input current is greater than 1000A.
Note: When the measurement session has been completed, disconnect the test leads from the
circuit under test and remove the test leads from the meter’s input terminals.
9
PQ2071-en-GB_V1.3 7/15
Power Measurements
Active, Reactive, and Apparent Power Measurements
There are three displays modes in this section as detailed in this section:

kW Active Power on Main Display

kVA Apparent Power on Main Display
(Reactive power on Secondary Display)

kVAR Reactive Power on Main Display
(Apparent power on Secondary Display)
(Phase Angle on Secondary Display)
WARNING: To avoid meter damage and personal injury do not measure RMS signals greater
than 750VAC or 1000AAC.
NOTES:

The maximum and minimum values are not available in this mode.

The summing of wattage values is only available in the KW mode.

When the measurement session has been completed, disconnect the test leads from the circuit
under test and remove leads from the meter’s input terminals.

Power connections and measurements shown for
3-Phase 4-wire
3-Phase 3-wire
Single and Split phase
10
PQ2071-en-GB_V1.3 7/15
3-Phase, 4-Wire Power Measurements
1.
Connect the four voltage leads as shown in
Figure. 7
2.
Clamp the transformer jaw around the power
conductors connected to the L1 voltage lead.
3.
Set the meter to kW. The dual display shows
the Active power kW value and the Phase
Angle (PG) value.
4.
Press the L1-L2-L3 button to choose the first
phase L1 (see figure 8).
5.
Press the ∑ button to save and sum the measured value
Figure 7
for L1. (see Figure 8)
6.
7.
Move the clamp jaw to the power conductor connected to the L2 voltage test lead.
Press the L1-L2-L3 button to choose the first phase
L2. The primary display shows the kW for phase L1
and the secondary display shows the Phase angle
(PG).
8.
Press the ∑ button to save and sum the measured
value for L2. (figure 8). The primary display shows the
kW for phase L2 and the secondary display shows the
Phase angle (PG).
9.
Move the clamp jaw to the power conductor
connected to the L3 voltage test lead.
10. Press the L1-L2-L3 button to choose the first phase L3. The primary display shows the kW for
phase L3 and the secondary display shows the Phase
angle (PG).
11. Press the ∑ button to save and sum the measured
value for L3. (figure 8)
12. After recording the kW power measurement value for
the third phase, press and Hold the
∑ button for 1 second to display the 3 phase sum of
kW on the main display and kVA on the secondary
display. (figure 9)
13. Press the ▲ button to display the 3 phase sum of
kVAR on the main display.
14. Press and Hold the ∑ button for 1 second to return to normal operation.
11
PQ2071-en-GB_V1.3 7/15
Figure 8
Figure 9
12
PQ2071-en-GB_V1.3 7/15
3-Phase, 3-Wire Power Power Measurements
Note:
When measuring 3 phase / 3-wire systems, hold down the L1-L2-L3 button for 5 seconds to display
the 3ϕ3w icon. (Press and hold the L1-L2-L3 button again for 5 seconds to exit the 3 phase/3-wire
mode back to the default 3Φ4wire mode).
Connect the Meter as shown in Figure 10.
Figure 10
1.
Insert the Red (L1) and Blue (L3) test leads into the L1, L3 meter input terminals and connect
these to 2 separate phases of the circuit under test as shown in Figure 10.
2.
Insert the black test lead into the COM input terminal on the meter and connect it to the last
remaining wire of the 3 phase 3-wire system under test.
3.
4.
Note Skip the second (L2) connection.
Set the Rotary switch to the KW position.
Press the L1-L2-L3 button to choose the first phase L1 (see figure 8). The primary display
shows the kW for phase L1 and the secondary display shows the Phase angle (PG).
5.
Press the ∑ button to save and sum the measured value for L1. (see Figure 8)
6.
Move the clamp jaw to the power conductor connected to the L3 voltage test lead.
7.
Press the L1-L2-L3 button to choose the first phase L3. The primary display shows the kW for
phase L3 and the secondary display shows the Phase angle (PG).
8.
Press the ∑ button to save and sum the measured value for L3. (figure 8)
9.
After recording the kW power measurement value for the L3 phase, press and Hold the
∑ button for 1 second to display the 3 phase sum of kW on the main display and kVA on the
secondary display. (figure 9)
10. Press the ▲ button to display the 3 phase sum of kVAR on the main display.
11. Press and Hold the ∑ button for 1 second to return to normal operation
For Figure 9: for 3-wire
∑W = W1 + W3
13
PQ2071-en-GB_V1.3 7/15
Single Phase and Split Phase Power Measurements
1.
2.
3.
4.
5.
6.
1. Clamp the transformer jaw and around the Power wire.
2. Connect the L1 test lead to this Power wire.
3. Connect the COM test lead to the neutral/com wire.
4. Set the Rotary switch to the KW, kVA or kVAR position
5. Press the L1-L2-L3 button to choose phase L1.
6. The display will show the power value.
The display will show the power value.
Single Phase
Split Phase
14
PQ2071-en-GB_V1.3 7/15
Power Factor
WARNING: To avoid meter damage and personal injury do not measure RMS signals
greater than 750VAC or 1000AAC.
Note: The MAX/MIN feature is not operational when measuring power factor.
A minimum of 10 amps is required for measuring an accurate power factor.
Power Factor measurement
1.
Set the Rotary switch to the PF position.
2.
3-phase - Connect the meter as shown in Fig. 7 (3P4W) or Fig. 10 (3P3W)
Single phase – Connect the L1 test lead to the Power wire and COM to the neutral wire.
3.
Clamp around the phase to be measured. (Power wire for Single phase).
4.
Press the L1-L2-L3 button to select the conductor that is clamped. (Fig.11)
5.
The dual display indicates the power factor (PF) in the main display and the phase angle
(PG) in the secondary display
Figure 11
15
PQ2071-en-GB_V1.3 7/15
Kilowatt Hours
WARNING: To avoid meter damage and personal injury do not measure RMS signals
greater than 750VAC or 1000AAC.
To test Kilowatt hours, connect the Meter as follows:
1.
Set the Rotary switch to the kWh position.
2.
Connect the meter as shown in Fig. 7 (3P4W) or Fig. 10 (3P3W) for 3-phase connections.
Single Phase – connect the L1 test lead to the Power wire and COM lead to Neutral.
3.
Clamp around the phase to be measured. (Power wire for single phase)
4.
Press the L1-L2-L3 button to select the conductor clamped. (L1 for single phase)
5.
6.
Press and Hold the CLEAR button for 1 second to reset the clock to 0.
The measured kWh value is displayed in the main display and the elapsed time in the
secondary display. (Fig. 12)
Figure 12
7.
8.
9.
10.
11.
12.
13.
Press HOLD to read a particular (time) kWh value. The reading and the elapsed time values
will be locked, but the continuous measuring time will be tracked and accumulated.
After noting the data, press HOLD again to perform a continuous measurement.
The kWh value will continue accumulate and the measuring time jumps to the present
measuring time.
When the measuring time exceeds 24 hours or if the Meter is switched to another
measurement mode, the active energy measurement will stop.
The maximum active energy is 9999kWh. OL will be displayed when the reading exceeds
this limit.
The MAXMIN feature is not available when measuring active energy.
Press and hold the CLEAR button for 1 second to reset the time and energy value.
16
PQ2071-en-GB_V1.3 7/15
LCD Backlight Button
The LCD is equipped with backlighting for easier viewing, especially in dimly lit areas. Press the
backlight button to switch the backlight ON. The backlight will automatically switch OFF after
approx. 20 seconds. Press the button to turn the backlight off manually
Automatic Power OFF
In order to conserve battery life, the meter will automatically turn off after approximately 25 minutes.
To turn the meter on again, turn the function switch to the OFF position and then to the desired
function position.
PC Interface
The meter connects to a PC via the supplied infrared to USB interface cable. The infrared side of
the cable connects to the port at the bottom of the meter and the USB end connects to the PC.
The supplied software permits the user to collect up to 50,000 readings as they are taken. The
readings can be displayed as a list or graph within the software environment or exported to a
spreadsheet.
Instructions for use of the PC interface and software are supplied on the software disk included in
the meter package.
True RMS Measurement and Average Value Measurements



True RMS measures the effective value of sine-wave and non-sine wave input signals
Average measurements represent the mean value of sine wave signals
The clamp Meter uses the following formulas:
KW = KVA × Cosθ
KVA = KW 2  KVAr 2
KVAr = KVA × Sinθ
17
PQ2071-en-GB_V1.3 7/15
Maintenance
WARNING: To avoid electrical shock, disconnect the meter from any circuit, remove the test leads
from the input terminals, and turn OFF the meter before opening the case. Do not operate the meter
with an open case.
Cleaning and Storage
Periodically wipe the case with a damp cloth and mild detergent; do not use abrasives or solvents. If
the meter is not to be used for 60 days or more, remove the battery and store it separately.
Battery Replacement
1.
Remove the Phillips head screw that secures the rear battery door
2.
Open the battery compartment
3.
Replace the 9 Volt battery
4.
Secure the battery compartment
5.
Dispose of batteries responsibly and according to all applicable laws
18
PQ2071-en-GB_V1.3 7/15
Electrical Specifications
Current, Voltage, and Frequency
Range &
Resolution
Function
Accuracy (% of
reading + digits)
Overload
Protect
Input
Impedance
Frequency
range
± (2% + 5d)
1000A
N/A
50-60Hz
± (1.2% + 5d)
750V rms
10M
50-120Hz
40.0 AAC
AC Current
100.0 AAC
400.0 ADC
1000 ADC
100.0VAC
AC Voltage
400.0 VAC
750.0VAC
Frequency
50 to 200Hz
± (0.5% + 5d)
Active Power (kW) W = V x A x COSθ
Voltage Ranges
Current / Voltage
Current
Ranges
100V
400V
750V
40A
4.00KW
16.00KW
30.00KW
100A
10.00KW
40.00KW
75.00KW
40.00KW
160.0KW
300.0KW
100.0KW
400.0KW
750.0KW
400A
1000A
Accuracy
±(3%+5)
Resolution
<1000KW: 0.01KW; 100kW: 0.1KW
19
PQ2071-en-GB_V1.3 7/15
Apparent Power (kVA) VA = V x A
Voltage Ranges
Current / Voltage
Current
Ranges
750V
100V
400V
40A
4.00KVA
16.00KVA
30.00KVA
100A
10.00KVA
40.00KVA
75.00KVA
40.00KVA
160.0KVA
300.0KVA
100.0KVA
400.0KVA
750.0KVA
400A
1000A
Accuracy
±(3%+5)
Resolution
<1000KVA: 0.01KVA; 100kW: 0.1KVA
Reactive Power (kVAR) Var = V x A x SINθ
Voltage Ranges
Current / Voltage
Current
Ranges
750V
100V
400V
40A
4.00KVAr
16.00KVAr
30.00KVAr
100A
10.00KVAr
40.00KVA
75.00KVAr
400A
40.00KVAr
160.0KVAr
300.0KVAr
100.0KVAr
400.0KVAr
750.0KVAr
1000A
Accuracy
±(3%+5)
Resolution
<1000KVAr: 0.01KVAr; 100kW: 0.1KVAr
20
PQ2071-en-GB_V1.3 7/15
Power Factor PF = W / VA
Range
Accuracy
Resolution
Measurement Considerations
0.3~1
(capacitive or
inductive)
±0.022
0.001
Minimum current 10A
Minimum voltage 45V
0.3~1
(capacitive or
inductive)
For reference only
Current less than 10A or
Voltage less than 45V
Phase Angle PG = a cos (PF)
Range
O
0 ~90
Accuracy
O
±2
Resolution
O
1
O
O
Minimum current 10A
Minimum voltage 45V
(capacitive or inductive)
0 ~90
Measurement Notes
O
For reference only
Current less than 10A
Voltage less than 45V
(capacitive or inductive)
Kilowatt Hours (kWh)
Range
Accuracy
Resolution
1~9999kWh
±(3%+2)
0.001kWh
21
PQ2071-en-GB_V1.3 7/15
General Specifications
Clamp jaw opening
57mm (2-1/4") approx.
Display
Dual 4-digit (9999 counts) backlit LCD
Bargraph
100 units
Low Battery indication
Battery symbol is displayed
Over-range indication
‘OL’ display
Internal Reading Memory
99 readings can be stored, recalled, and cleared.
External PC Memory
50,000 readings can be recorded on a connected PC running the
supplied PC software. Readings can be exported to a spreadsheet.
Measurement rate
2 readings per second, nominal
Input Impedance
10M (VAC)
AC bandwidth
50 to 200Hz (AAC and VAC)
AC response
True rms (AAC and VAC)
Operating Temperature
5C to 40C (41F to 104 F)
Storage Temperature
-20C to 60C (-4F to 140F)
Operating Humidity
< 80% up to 31C (87F) decreasing linearly to 50% at 40C (104F)
Storage Humidity
< 80%
Operating Altitude
2000meters (7000ft) maximum
Battery
One (1) 9V Battery (NEDA 1604)
Auto power OFF
After approx. 25 minutes
Dimensions & Weight
292 x 95 x 38mm (11.5 x 3.75 x 1.5”); 522g (18.4 oz)
Safety
For indoor use and in accordance with the requirements for double
insulation to IEC1010-1 (2001): EN61010-1 (2001) Overvoltage
Category IV 600V and Category III 1000V, Pollution Degree 2
Copyright © 2015 FLIR Systems, Inc. All rights reserved including the right of reproduction in whole or in part in any form www.extech.com 22
PQ2071-en-GB_V1.3 7/15