BCF240T HIGH EFFICIENCY HETEROJUNCTION POWER FET CHIP (.3 µm x 2400 µm) The BeRex BCF240T is a GaAs Power MESFET whose nominal 0.3 micron gate length and 2400 micron gate width make the product ideally suited to applications requiring high OIP3 linearity and low phase noise while providing high-gain and medium power from DC to 26.5 GHz. This product is well suited for either wideband or narrow-band applications. The BCF240T is produced using state of the art metallization and devices from each wafer are screened to insure reliability. These chips utilize SI3N4 passivation for increased reliability. Product Features • 30.4 dBm Typical Output Power • 9.8 dB Typical Power Gain @ 12 GHz • Low Phase Noise • 0.3 X 2400 Micron Recessed Gate Applications • Commercial • Military / Hi-Rel • Test & Measurement DC CHARACTERISTIC (Ta = 25° C) PARAMETER/TEST CONDITIONS Idss Saturated Drain Current (Vgs = 0V, Vds = 2V) Gm Transconductance (Vds = 3V, Vgs = 50% Idss) Vp Pinch-off Voltage (Ids = 2400 µA, Vds = 3V) MINIMUM TYPICAL MAXIMUM UNIT 480 720 960 mA -3.5 400 mS -2.0 V BVgd Drain Breakdown Voltage (Ig = 2.4 mA, source open) -15 -11 V BVgs Source Breakdown Voltage (Ig = 2.4 mA, drain open) -10 -7 V Rth Thermal Resistance (Au-Sn Eutectic Attach) 23 www.berex.com BeRex, Inc. 3350 Scott Blvd. #61-01 Santa Clara, CA 95054 tel. (408) 452-5595 Specifications are subject to change without notice. ©BeRex 2015 ° C/W January 2015 Rev. 1.3 BCF240T ELECTRICAL CHARACTERISTIC (Vds = 8V, Ta = 25° C) PARAMETER/TEST CONDITIONS P1dB Output Power @ P1dB (Vds = 8V, Ids = 50% Idss) G1dB Gain @ P1dB (Vds = 8V, Ids = 50% Idss) PAE PAE @ P1dB (Vds = 8V, Ids = 50% Idss) TEST FREQUENCY 12 GHZ 18 GHZ 12 GHZ 18 GHZ 12 GHZ 18 GHZ MINIMUM TYPICAL 28.4 28.1 7.8 5.7 30.4 30.1 9.8 7.7 26.7 25.5 UNI T MAXIMUM dBm dB % ELECTRICAL CHARACTERISTIC (Vds = 6V, Ta = 25° C) PARAMETER/TEST CONDITIONS P1dB Output Power @ P1dB (Vds = 6V, Ids = 50% Idss) G1dB Gain @ P1dB (Vds = 6V, Ids = 50% Idss) PAE PAE @ P1dB (Vds = 6V, Ids = 50% Idss) TEST FREQUENCY 12 GHZ 18 GHZ 12 GHZ 18 GHZ 12 GHZ 18 GHZ MINIMUM TYPICAL 28.8 28.1 7.1 5.4 30.8 30.1 9.1 7.4 40 33 UNI T MAXIMUM dBm dB % MAXIMUM RATINGS (Ta = 25° C) PARAMETERS Vds Vgs Ids Igsf Pin Tch Tstg Pt Drain-Source Voltage Gate-Source Voltage Drain Current Forward Gate Current Input Power Channel Temperature Storage Temperature Total Power Dissipation ABSOLUTE CONTINUOUS 12 V -8 V Idss 60 mA 29 dBm 175° C -60° C - 150° C 5.4 W 8V -4V Idss 9.6 mA @ 3dB compression 150° C -60° C - 150° C 4.5 W Exceeding any of the above Maximum Ratings will result in reduced MTTF and may cause permanent damage to the device www.berex.com BeRex, Inc. 3350 Scott Blvd. #61-01 Santa Clara, CA 95054 tel. (408) 452-5595 Specifications are subject to change without notice. ©BeRex 2015 January 2015 Rev. 1.3 BCF240T Pin_Pout/Gain, PAE (12 GHz) Freq. = 12 GHz, Vds = 8 V, Ids = 50% Idss Freq. = 12 GHz, Vds = 6 V, Ids = 50% Idss www.berex.com BeRex, Inc. 3350 Scott Blvd. #61-01 Santa Clara, CA 95054 tel. (408) 452-5595 Specifications are subject to change without notice. ©BeRex 2015 January 2015 Rev. 1.3 BCF240T Pin_Pout/Gain, PAE (18 GHz) Freq. = 18 GHz, Vds = 8 V, Ids = 50% Idss Freq. = 18 GHz, Vds = 6 V, Ids = 50% Idss www.berex.com BeRex, Inc. 3350 Scott Blvd. #61-01 Santa Clara, CA 95054 tel. (408) 452-5595 Specifications are subject to change without notice. ©BeRex 2015 January 2015 Rev. 1.3 BCF240T Wire Bonding Options ㆍ Gold Bonding Wire information 1. Gate to input transmission line - Length and Height : 400 um and 250 um - Number of wires: 4 2. Drain to output transmission line - Length and Height : 350 um and 250 um - Number of wires: 4 3. Source to ground plate - Length and Height : 200 um x 250 um - Number of wires: 10 Note: The diameter of bonding wires: 1 mil www.berex.com BeRex, Inc. 3350 Scott Blvd. #61-01 Santa Clara, CA 95054 tel. (408) 452-5595 Specifications are subject to change without notice. ©BeRex 2015 January 2015 Rev. 1.3 BCF240T DIE ATTACH RECOMMENDATIONS: BeRex recommends the “Eutectic” die attach using Au-Sn (80%-20%) pre-forms. The die attach station must have accurate temperature control, and the operation should be performed with parts no hotter than 300°C for less than 10 seconds. An inert forming gas (90% N2-10% H2) or clean, dry N2 should be used. HANDLING PRECAUTIONS: GaAs FETs are very sensitive to and may be damaged by Electrostatic Discharge (ESD). Therefore, proper ESD precautions must be taken whenever you are handling these devices. It is critically important that all work surfaces, and assembly equipment, as well as the operator be properly grounded when handling these devices to prevent ESD damage. STORAGE & SHIPPING: BeRex’s standard chip device shipping package consists of an antistatic “Gel-Pak”, holding the chips, placed inside a sealed antistatic and moisture barrier bag. This packaging is designed to provide a reasonable measure of protection from both mechanical and ESD damage. Chip devices should be stored in a clean, dry Nitrogen gas environment at room temperature until they are required for assembly. Only open the shipping package or perform die assembly in a work area with a class 10,000 or better clean room environment to prevent contamination of the exposed devices. CAUTION: THIS PRODUCT CONTAINS GALLIUM ARSENIDE (GaAs) WHICH CAN BE HAZARDOUS TO THE HUMAN BODY AND THE ENVIRONMENT. THEREFORE, IT MUST BE HANDLED WITH CARE AND IN ACCORDANCE WITH ALL GOVERNMENTAL AND COMPANY REGULATIONS FOR THE SAFE HANDLING AND DISPOSAL OF HAZARDOUS WASTE. DO NOT BURN, DESTROY, CUT, CRUSH OR CHEMICALLY DISSOLVE THE PRODUCT. DO NOT LICK THE PRODUCT OR IN ANY WAY ALLOW IT TO ENTER THE MOUTH. EXCLUDE THE PRODUCT FROM GENERAL INDUSTRIAL WASTE OR GARBAGE AND DISPOSE OF ONLY IN ACCORDANCE TO APPLICABLE LAWS AND/OR ORDINANCES. DISCLAIMER BEREX RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. BEREX DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN. LIFE SUPPORT POLICY BEREX PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES WITHOUT THE EXPRESS WRITTEN APPROVAL OF BEREX. 1. Life support devices or systems are devices or systems which (a) are intended for surgical implant into the body, or (b) support or sustain life, or (c) whose failure to perform when properly used in accordance with instructions for use provided in labeling, can be reasonably expected to result in significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.berex.com BeRex, Inc. 3350 Scott Blvd. #61-01 Santa Clara, CA 95054 tel. (408) 452-5595 Specifications are subject to change without notice. ©BeRex 2015 January 2015 Rev. 1.3