1N4001 THRU 1N4007 1.0AMP . SILICON RECTIFIERS FEATURE .High current capability, .Low forward voltage drop .Low power loss, high efficiency .High surge capability .High temperature soldering guaranteed 260°C /1 0sec/0.375" lead length at 5 lbs tension DO-41 .7 8 7 ( 2 0 .0 ) M IN . .1 0 7 ( 2 .7 ) .0 8 0 ( 2 .0 ) + .2 0 5 ( 5 .2 ) .1 6 6 ( 4 .2 ) MECHANICAL DATA .Terminal: Plated axial leads solderable per MIL-STD 202E, method 208C .Case: Molded with UL-94 Class V-0 recognized Flame Retardant Epoxy .Polarity: color band denotes cathode .Mounting position: any D IA . - .7 8 7 ( 2 0 .0 ) M IN . .0 3 2 ( 0 .8 ) .0 2 5 ( 0 .6 5 ) D IA Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS (single-phase, half-wave, 60HZ, resistive or inductive load rating at 25°C, unless otherwise stated) SYM BOL Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC blocking Voltage Maximum Average Forward Rectified Current .375"(9.5mm)lead length @Ta =75°C VRRM VRMS VDC 1N 4001 50 1N 4002 100 1N 4003 200 1N 4004 400 1N 4005 600 1N 4006 800 1N 4007 units 1000 V 35 70 140 280 420 560 700 V 50 100 200 400 600 800 1000 V IF(AV) 1.0 A IFSM 30.0 A VF VF 1.0 V 1.3 V Peak Forward Surge Current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) Maximum Forward Voltage at 1.0A DC Maximum Forward Voltage at 3.0A DC Maximum DC Reverse Current Ta =25°C at rated DC blocking voltage Ta =100°C Typical Junction Capacitance (Note 1) Typical Thermal Resistance (Note 2) Storage Temperature Operation Junction Temperature 5.0 IR 50.0 CJ R(JA) TSTG TJ 15 pF 50 °C/W -55 to +150 °C -55 to +125 °C Note: 1. Measured at 1.0 MHz and applied reverse voltage of 4.0Vdc 2. Thermal Resistance from Junction to Ambient at 0.375"（9.5mm） lead length, vertical P.C. Board Mounted - 315 - µA RATING AND CHARACTERISTIC CURVES (1N4001 THRU 1N4007) FIG.1-TYPICAL FORWARD CURRENT DERATING CURVE FIG.2-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANEOUS FORWARD CURRENT,(A) AVERGE FORWARD RECTIFIED CURRENT,(A) 10.0 1.0 0.5 Single Phase Half Wave 60Hz Resistive or inductive Load 0 0 50 100 150 1.0 TJ=25℃ Pulse Width=300μ s 1% Duty Cycle .1 .01 200 .8 .5 1.1 1.7 1.4 INSTANEOUS FORWARD VOLTAGE,(V) AMBIENT TEMPERTURE,( ℃ ) FIG.4-TYPICAL REVERSE CHARACTERISTICS FIG.3-MAXIMUN NON-REPETITIVE FORWARD SURGE CURRENT 40 8.3ms Single Half Sine-Wave (JEDEC Method) 30 INSTANEOUS REVERSE CURRENT,(μA) PEAK FORWARD SURGE CURRENT,(A) 100 20 10 10 1 TJ=25℃ 0 0 10 100 NUMBER OF CYCLES AT 60Hz .1 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) - 316 -