NIS5232 - +12 Volt Electronic Fuse

NIS5232 Series
+12 Volt Electronic Fuse
The NIS5232 is a cost effective, resettable fuse which can greatly
enhance the reliability of a hard drive or other circuit from both
catastrophic and shutdown failures.
It is designed to buffer the load device from excessive input voltage
which can damage sensitive circuits. It also includes an overvoltage
clamp circuit that limits the output voltage during transients but does
not shut the unit down, thereby allowing the load circuit to continue
operation.
Features
•
•
•
•
•
•
•
•
•
•
•
Integrated Power Device
Power Device Thermally Protected
No External Current Shunt Required
9 V to 18 V Input Range
44 mW Typical
Internal Charge Pump
Internal Undervoltage Lockout Circuit
Internal Overvoltage Clamp
ESD Ratings: Human Body Model (HBM); 1500 V
Machine Model (MM); 200 V
UL2367 Approved (UL File #E466553)
These Devices are Pb−Free and are RoHS Compliant
http://onsemi.com
4.2 AMP, 12 VOLT
ELECTRONIC FUSE
DFN10
CASE 485C
MARKING DIAGRAM
1
232
AYWG
G
Typical Applications
• Hard Drives
• Mother Board Power Management
232
A
Y
W
G
Pin
1
2
3
4
5
6−10
11 (flag)
Function
GND
dv/dt
Enable/Fault
ILIMIT
NC
SOURCE
VCC
= Latching Version
= Assembly Location
= Year
= Work Week
= Pb−Free Package
(Note: Microdot may be in either location)
ORDERING INFORMATION
See detailed ordering and shipping information in the ordering
information section on page 10 of this data sheet.
© Semiconductor Components Industries, LLC, 2014
July, 2014 − Rev. 2
1
Publication Order Number:
NIS5232/D
NIS5232 Series
VCC
Enable
ENABLE/
FAULT
Charge
Pump
SOURCE
Current
Limit
Thermal
Shutdown
UVLO
Voltage
Clamp
ILIMIT
dv/dt
dv/dt
Control
Figure 1. Block Diagram
GND
Table 1. FUNCTIONAL PIN DESCRIPTION
Pin
Function
1
Ground
2
dv/dt
3
Enable/Fault
4
ILimit
6−10
Source
11 (belly pad)
VCC
Description
Negative input voltage to the device. This is used as the internal reference for the IC.
The internal dv/dt circuit controls the slew rate of the output voltage at turn on. It has an internal
capacitor that allows it to ramp up over a period of 2 ms. An external capacitor can be added to this
pin to increase the ramp time. If an additional time delay is not required, this pin should be left open.
The enable/fault pin is a tri−state, bidirectional interface. It can be used to enable or disable the output
of the device by pulling it to ground using an open drain or open collector device. If a thermal fault
occurs, the voltage on this pin will go to an intermediate state to signal a monitoring circuit that the
device is in thermal shutdown. It can also be connected to another device in this family to cause a
simultaneous shutdown during thermal events.
A resistor between this pin and the source pin sets the overload and short circuit current limit levels.
This pin is the source of the internal power FET and the output terminal of the fuse.
Positive input voltage to the device.
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
Input Voltage, operating, steady−state (VCC to GND, Note 1)
Transient (100 ms)
VIN
−0.6 to 18
−0.6 to 25
V
Thermal Resistance, Junction−to−Air
0.1 in2 copper (Note 2)
0.5 in2 copper (Note 2)
4−layer board (Note 4)
qJA
Thermal Resistance, Junction−to−Lead (Pin 1)
qJL
Thermal Resistance, Junction−to−Case
160
95
50
°C/W
27
°C/W
qJC
20
°C/W
Pmax
1.3
10.4
W
mW/°C
Operating Temperature Range (Note 3)
TJ
−40 to 150
°C
Nonoperating Temperature Range
TJ
−55 to 155
°C
Lead Temperature, Soldering (10 Sec)
TL
260
°C
Total Power Dissipation @ TA = 25°C
Derate above 25°C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. Negative voltage will not damage device provided that the power dissipation is limited to the rated allowable power for the package.
2. 1 oz. copper, double−sided FR4.
3. Thermal limit is set above the maximum thermal rating. It is not recommended to operate this device at temperatures greater than the
maximum ratings for extended periods of time.
4. JESD51−7 4−layer board.
http://onsemi.com
2
NIS5232 Series
ELECTRICAL CHARACTERISTICS (Unless otherwise noted: VCC = 12 V, CL = 100 mF, dv/dt pin open, RLIMIT = 10 W, Tj = 25°C
unless otherwise noted.)
Characteristics
Symbol
Min
Typ
Max
Unit
POWER FET
Delay Time (enabling of chip to ID = 100 mA with 1 A resistive load)
Kelvin ON Resistance (Note 5)
TJ = 140°C (Note 6)
Tdly
RDSon
Off State Output Voltage
(VCC = 18 Vdc, VGS = 0 Vdc, RL = R)
220
35
Voff
Output Capacitance (VDS = 12 Vdc, VGS = 0 Vdc, f = 1 MHz)
Continuous Current (TA = 25°C, 0.5
(TA = 80°C, minimum copper)
in2
copper) (Note 6)
ID
ID
ms
44
62
55
mW
190
300
mV
250
pF
4.2
2.5
A
THERMAL LATCH
TSD
150
175
200
°C
Output Clamping Voltage (Overvoltage Protection) (VCC = 18 V)
VClamp
14
15
16.2
V
Undervoltage Lockout (Turn on, voltage going high)
VUVLO
7.7
8.5
9.3
V
UVLO Hysteresis
VHyst
−
0.80
−
V
Kelvin Short Circuit Current Limit (RLimit = 15.4 W, Note 7)
ILim−SS
2.75
3.44
4.25
A
Kelvin Overload Current Limit (RLimit = 15.4 W, Note 7)
ILim−OL
Shutdown Temperature (Note 6)
UNDER/OVERVOLTAGE PROTECTION
CURRENT LIMIT
4.6
A
dv/dt CIRCUIT
Output Voltage Ramp Time (Enable to VOUT = 11.7 V)
tslew
Maximum Capacitor Voltage
Vmax
0.5
0.9
1.8
ms
VCC
V
ENABLE/FAULT
Logic Level Low (Output Disabled)
Vin−low
0.35
0.58
0.81
V
Logic Level Mid (Thermal Fault, Output Disabled)
Vin−mid
0.82
1.4
1.95
V
Logic Level High (Output Enabled)
Vin−high
1.96
2.64
3.30
V
High State Maximum Voltage
Vin−max
3.40
4.30
5.2
V
−17
−25
mA
Logic Low Sink Current (Venable = 0 V)
Iin−low
Logic High Leakage Current for External Switch (Venable = 3.3 V)
Iin−leak
1.0
mA
Fan
3.0
Units
2.5
mA
Maximum Fanout for Fault Signal (Total number of chips that can be
connected to this pin for simultaneous shutdown)
TOTAL DEVICE
Bias Current (Operational)
IBias
1. 8
Bias Current (Shutdown)
IBias
1.0
Minimum Operating Voltage (Notes 6 and 8)
Vmin
mA
7.6
V
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
5. Pulse test: Pulse width 300 ms, duty cycle 2%.
6. Verified by design.
7. Refer to explanation of short circuit and overload conditions in application note AND8140.
8. Device will shut down prior to reaching this level based on actual UVLO trip point.
http://onsemi.com
3
NIS5232 Series
60
50_C
50
POWER (W)
25_C
40
30
20
80_C
10
0
0.1
1
10
100
1000
10000 100000
TIME (ms)
Figure 2. Power Dissipation vs. Thermal Trip Time
+12 V
11 V
CC
SOURCE
NIS5232
ILIMIT
3
RS
4
ENABLE/
FAULT
GND
dv/dt
1
ENABLE
10
9
8
7
6
LOAD
2
GND
Figure 3. Application Circuit with Direct Current Sensing
+12 V
11 V
CC
SOURCE
NIS5232
ILIMIT
3
4
RS
ENABLE/
FAULT
GND
ENABLE
10
9
8
7
6
dv/dt
1
2
GND
Figure 4. Application Circuit with Kelvin Current Sensing
http://onsemi.com
4
LOAD
NIS5232 Series
VCC
VCC
SOURCE
SOURCE
RS
NIS5135
ILIMIT
LOAD
dv/dt
NIS5232
ENABLE/
FAULT
ILIMIT
ENABLE/
FAULT
GND
GND
ENABLE
Figure 5. Common Thermal Shutdown
http://onsemi.com
5
dv/dt
LOAD
NIS5232 Series
9
0.86
8.8
0.84
0.82
8.4
HYST (V)
UVLO (V)
8.6
8.2
8
0.78
0.76
7.8
0.74
7.6
7.4
−50
0.8
−25
0
25
50
75
100
125
0.72
−50
150
−25
0
25
50
75
100
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 6. UVLO Turn−On
Figure 7. UVLO Hysteresis
15.3
125 150
1.05
15.2
1
RAMP TIME (ms)
15
14.9
14.8
14.7
0.95
0.9
14.6
14.5
−50
−25
0
25
50
75
100
125
0.85
−50
150
−25
0
25
50
75
100
125 150
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 8. Output Clamping Voltage
Figure 9. Output Voltage dv/dt Rate
1600
1200
CURRENT (mA)
VOLTAGE (V)
15.1
800
400
0
0.5
0.6
0.7
FORWARD VOLTAGE (V)
Figure 10. Input Transient Response
Figure 11. Body Diode Forward
Characteristics
http://onsemi.com
6
0.8
NIS5232 Series
9
10
OL
−40°C
CURRENT (A)
CURRENT (A)
8
0°C
7
25°C
50°C
6
85°C
5
4
SC
1
0
0.5
1
COPPER AREA
1.5
0.1
2
10
100
(in2)
1000
Rlimit (W)
Figure 12. Thermal Limit vs. Copper Area and
Ambient Temperature
Figure 13. Current Limit vs. Rsense for Direct
Current Sensing
4.5
10
4
3
CURRENT (A)
CURRENT (A)
OL
OL
3.5
SC
2.5
2
1.5
SC
1
1
0.5
0
−50
0
50
100
0.1
150
1
10
100
TEMPERATURE (°C)
Rsense (W)
Figure 14. Direct Current Sensing Levels vs.
Temperature for 27 W Sense Resistor
Figure 15. Current Limit vs. Rsense for Kelvin
Current Sensing
6
4
5.5
3.5
5
OL
CURRENT (A)
CURRENT (A)
OL
4.5
4
SC
3
2.5
2
SC
1.5
3.5
3
−40
−20
0
20
40
60
TEMPERATURE (°C)
80
1
100
−40
Figure 16. Kelvin Current Sensing Levels vs.
Temperature for 15 W Sense Resistor
−20
0
20
40
60
TEMPERATURE (°C)
80
Figure 17. Kelvin Current Sensing Levels vs.
Temperature for 33 W Sense Resistor
http://onsemi.com
7
100
NIS5232 Series
ON RESISTANCE (mW)
55
50
45
40
7.0
9.0
11
13
15
VCC (V)
Figure 18. On Resistance vs. VCC
APPLICATION INFORMATION
Basic Operation
device is actively limiting the current and the gate is at an
intermediate level. For a more detailed description of this
circuit please refer to application note AND8140.
There are two methods of biasing the current limit circuit
for this device. They are shown in the two application
figures. Direct current sensing connects the sense resistor
between the current limit pin and the load. This method
includes the bond wire resistance in the current limit circuit.
This resistance has an impact on the current limit levels for
a given resistor and may vary slightly depending on the
impedance between the sense resistor and the source pins.
The on resistance of the device will be slightly lower in this
configuration since all five source pins are connected in
parallel and therefore, the effective bond wire resistance is
one fifth of the resistance for any given pin.
The other method is Kelvin sensing. This method uses one
of the source pins as the connection for the current sense
resistor. This connection senses the voltage on the die and
therefore any bond wire resistance and external impedance
on the board have no effect on the current limit levels. In this
configuration the on resistance is slightly increased relative
to the direct sense method since only four of the source pins
are used for power.
This device is a self−protected, resettable, electronic fuse.
It contains circuits to monitor the input voltage, output
voltage, output current and die temperature.
On application of the input voltage, the device will apply
the input voltage to the load based on the restrictions of the
controlling circuits. The dv/dt of the output voltage will be
controlled by the internal dv/dt circuit. The output voltage
will slew from 0 V to the rated output voltage in 2 ms, unless
additional capacitance is added to the dv/dt pin.
The device will remain on as long as the temperature does
not exceed the 175°C limit that is programmed into the chip.
The current limit circuit does not shut down the part but will
reduce the conductivity of the FET to maintain a constant
current at the internally set current limit level. The input
overvoltage clamp also does not shutdown the part, but will
limit the output voltage to 15 V in the event that the input
exceeds that level.
An internal charge pump provides bias for the gate voltage
of the internal n−channel power FET and also for the current
limit circuit. The remainder of the control circuitry operates
between the input voltage (VCC) and ground.
Current Limit
The current limit circuit uses a SENSEFET along with a
reference and amplifier to control the peak current in the
device. The SENSEFET allows for a small fraction of the
load current to be measured, which has the advantage of
reducing the losses in the sense resistor as well as increasing
the value and decreasing the power rating of the sense
resistor. Sense resistors are typically in the tens of ohms
range with power ratings of several milliwatts making them
very inexpensive chip resistors.
The current limit circuit has two limiting values, one for
short circuit events which are defined as the mode of
operation in which the gate is high and the FET is fully
enhanced. The overload mode of operation occurs when the
Overvoltage Clamp
The overvoltage clamp consists of an amplifier and
reference. It monitors the output voltage and if the input
voltage exceeds 15 V, the gate drive of the main FET is
reduced to limit the output. This is intended to allow
operation through transients while protecting the load. If an
overvoltage condition exists for many seconds, the device
may overheat due to the voltage drop across the FET
combined with the load current. In this event, the thermal
protection circuit would shut down the device.
http://onsemi.com
8
NIS5232 Series
Undervoltage Lockout
information to other devices regarding the state of the chip.
When this pin is low, the output of the fuse will be turned off.
When this pin is high the output of the fuse will be
turned−on. If a thermal fault occurs, this pin will be pulled
low to an intermediate level by an internal circuit.
To use as a simple enable pin, an open drain or open
collector device should be connected to this pin. Due to its
tri−state operation, it should not be connected to any type of
logic with an internal pullup device.
If the chip shuts down due to the die temperature reaching
its thermal limit, this pin will be pulled down to an
intermediate level. This signal can be monitored by an
external circuit to communicate that a thermal shutdown has
occurred. If this pin is tied to another device in this family
(NIS5232 or NIS5135), a thermal shutdown of one device
will cause both devices to disable their outputs. Both devices
will turn on once the fault is removed for the auto−retry
devices.
For the latching thermal device, the outputs will be
enabled after the enable pin has been pulled to ground with
an external switch and then allowed to go high or after the
input power has been recycled. For the auto retry devices,
both devices will restart as soon as the die temperature of the
device in shutdown has been reduced to the lower thermal
limit.
The undervoltage lockout circuit uses a comparator with
hysteresis to monitor the input voltage. If the input voltage
drops below the specified level, the output switch will be
switched to a high impedance state.
dv/dt Circuit
The dv/dt circuit brings the output voltage up under a
linear, controlled rate regardless of the load impedance
characteristics. An internal ramp generator creates a linear
ramp, and a control circuit forces the output voltage to
follow that ramp, scaled by a factor.
The default ramp time is approximately 2 ms. This can be
modified by adding an external capacitor at the dv/dt pin.
This pin includes an internal current source of
approximately 85 nA. Since the current level is very low, it
is important to use a ceramic cap or other low leakage
capacitor. Aluminum electrolytic capacitors are not
recommended for this circuit.
The ramp time from 0 to the nominal output voltage can
be determined by the following equation, where t is in
seconds:
t 0*12 + 24e6 @ ǒ50 pF ) C extǓ
C ext +
t 0−12
24e6
* 50 pF
Thermal Protection
Where:
C is in Farads
t is in seconds
Any time that the unit shuts down due to a fault, enable
shut−down, or recycling of input power, the timing capacitor
will be discharged and the output voltage will ramp from 0
at turn on.
The NIS5232 includes an internal temperature sensing
circuit that senses the temperature on the die of the power
FET. If the temperature reaches 175°C, the device will shut
down, and remove power from the load. Output power can
be restored by either recycling the input power or toggling
the enable pin.
The thermal limit has been set high intentionally, to
increase the trip time during high power transient events. It
is not recommended to operate this device above 150°C for
extended periods of time.
Enable/Fault
The Enable/Fault pin is a multi−function, bidirectional pin
that can control the output of the chip as well as send
Figure 19. Fault/Enable Signal Levels
http://onsemi.com
9
NIS5232 Series
4.3 V
Startup
Blanking
12 mA
2.64 V
Enable/Fault
1.4 V
0.58 V
SD
Enable SD
+
−
−
+
Thermal Reset
Thermal
Shutdown
Thermal SD
Figure 20. Enable/Fault Simplified Circuit
ORDERING INFORMATION
Device
NIS5232MN1TXG
Features
Package
Shipping†
Thermal Latching
DFN10
(Pb−Free)
3000 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
10
NIS5232 Series
PACKAGE DIMENSIONS
DFN10, 3x3, 0.5P
CASE 485C
ISSUE C
D
PIN 1
REFERENCE
2X
2X
L1
ÇÇÇ
ÇÇÇ
ÇÇÇ
0.15 C
EDGE OF PACKAGE
A
B
E
DETAIL A
Bottom View
(Optional)
EXPOSED Cu
TOP VIEW
MOLD CMPD
0.15 C
(A3)
DETAIL B
0.10 C
A1
A
10X
A1
D2
10X
10X
L
1
C
SOLDERING FOOTPRINT*
DETAIL A
e
2.6016
5
DIM
A
A1
A3
b
D
D2
E
E2
e
K
L
L1
MILLIMETERS
MIN
MAX
0.80
1.00
0.00
0.05
0.20 REF
0.18
0.30
3.00 BSC
2.40
2.60
3.00 BSC
1.70
1.90
0.50 BSC
0.19 TYP
0.35
0.45
0.00
0.03
E2
K
1.8508
2.1746
10
10X
3.3048
6
b
0.10 C A B
0.05 C
A3
DETAIL B
Side View
(Optional)
SEATING
PLANE
0.08 C
SIDE VIEW
ÉÉÉ
ÉÉÉ
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.25 AND 0.30 MM FROM TERMINAL.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
5. TERMINAL b MAY HAVE MOLD COMPOUND
MATERIAL ALONG SIDE EDGE. MOLD
FLASHING MAY NOT EXCEED 30 MICRONS
ONTO BOTTOM SURFACE OF TERMINAL b.
6. DETAILS A AND B SHOW OPTIONAL VIEWS
FOR END OF TERMINAL LEAD AT EDGE OF
PACKAGE.
7. FOR DEVICE OPN CONTAINING W OPTION,
DETAIL B ALTERNATE CONSTRUCTION IS
NOT APPLICABLE.
BOTTOM VIEW
NOTE 3
10X
0.5651
10X
0.5000 PITCH
0.3008
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
11
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NIS5232/D