NCP1608BOOSTGEVB NCP1608 100 W Boost Evaluation Board User's Manual http://onsemi.com EVAL BOARD USER’S MANUAL Introduction The NCP1608 is a voltage mode power factor correction (PFC) controller designed to implement converters to comply with line current harmonic regulations. The device operates in critical conduction mode (CrM) for optimal performance in applications up to 350 W. Its voltage mode scheme enables it to obtain near unity power factor (PF) without the need for a line-sensing network. The output voltage is accurately controlled with an integrated high precision transconductance error amplifier. The controller also implements a comprehensive set of safety features that simplify system design. This application note describes the design and implementation of a 400 V, 100 W, CrM boost PFC converter using the NCP1608. The converter exhibits high PF, low standby power dissipation, high active mode efficiency, and a variety of protection features. Most electronic ballasts and switch−mode power supplies (SMPS) use a diode bridge rectifier and a bulk storage capacitor to produce a dc voltage from the utility ac line. This causes a non-sinusoidal current consumption and increases the stress on the power delivery infrastructure. Government regulations and utility requirements mandate control over line current harmonic content. Active PFC circuits are the most popular method to comply with these harmonic content requirements. System solutions consist of connecting a PFC pre−converter between the rectifier bridge and the bulk capacitor (Figure 1). The boost converter is the most popular topology for active PF correction. It produces a constant output voltage and consumes a sinusoidal input current from the line. PFC Pre−Converter Rectifiers AC Line The Need for PFC + High Frequency Bypass Capacitor Converter + NCP1608 Bulk Storage Capacitor Load Figure 1. Active PFC Stage with the NCP1608 Basic Operation of a CrM Boost Converter operation. This control method causes the frequency to vary with the instantaneous line input voltage (Vin) and the output load. The operation and waveforms of a CrM PFC boost converter are illustrated in Figure 2. For detailed information on the operation of a CrM boost converter for PFC applications, please refer to AND8123 at www.onsemi.com. For medium power (< 350 W) applications, CrM is the preferred control method. CrM operates at the boundary between discontinuous conduction mode (DCM) and continuous conduction mode (CCM). In CrM, the drive on time begins when the inductor current reaches zero. CrM combines the reduced peak current of CCM operation with the zero current switching of DCM © Semiconductor Components Industries, LLC, 2012 November, 2012 − Rev. 1 1 Publication Order Number: EVBUM2162/D NCP1608BOOSTGEVB Diode Bridge + Vin IL + L + AC Line Diode Bridge IL Vdrain Vin Vdrain L + AC Line + Vout − − The power switch is ON The power switch is OFF With the power switch voltage being about zero, the input voltage is applied across the inductor. The inductor current linearly increases with a (Vin/L) slope. Inductor Current The inductor current flows through the diode. The inductor voltage is (Vout − Vin) and the inductor current linearly decays with a (Vout − Vin)/L slope. (Vout − Vin)/L Vin/L Critical Conduction Mode: Next current cycle starts when the core is reset. IL(peak) Vdrain Vout Vin If next cycle does not start then Vdrain rings towards Vin Figure 2. Schematic and Waveforms of an Ideal CrM Boost Converter Features of the NCP1608 For detailed information on the operation of the NCP1608, please refer to NCP1608/D at www.onsemi.com. A CrM boost pre-converter featuring the NCP1608 is shown in Figure 3. The NCP1608 is an excellent controller for robust medium power CrM boost PFC applications due to its integrated safety features, low impedance driver, high precision error amplifier, and low standby current consumption. Vin L Vout D NB:NZCD LOAD (Ballast, SMPS, etc.) RZCD + AC Line EMI Filter Cin Rout1 1 2 3 Rout2 CCOMP 4 Ct NCP1608 FB VCC Control DRV Ct GND CS ZCD VCC 8 7 + M Cbulk 6 5 Rsense Figure 3. CrM Boost PFC Stage Featuring the NCP1608 A combination of resistors and capacitors connected between the Control and ground pins forms a compensation network that limits the bandwidth of the converter. For high PF, the bandwidth is set to less than 20 Hz. A capacitor connected to the Ct pin sets the maximum on time. The CS pin provides cycle−by−cycle overcurrent protection. The The FB pin senses the boost output voltage through the resistor divider formed by Rout1 and Rout2. The FB pin includes overvoltage protection (OVP), undervoltage protection (UVP), and floating pin protection (FPP). This pin is the input to the error amplifier. The output of the error amplifier is the Control pin. http://onsemi.com 2 NCP1608BOOSTGEVB The VCC pin is the supply pin of the controller. When VCC is less than the turn on voltage (VCC(on)), the current consumption of the device is less than 35 mA. This results in fast startup times and reduced standby power losses. internal comparator compares the voltage developed across Rsense (VCS) to an internal reference (VILIM). The driver turns off when VCS reaches VILIM. The ZCD pin senses the demagnetization of the boost inductor to turn on the drive. The drive on time begins after the ZCD pin voltage (VZCD) exceeds VZCD(ARM) and then decreases to less than VZCD(TRIG). A resistor in series with the ZCD winding limits the ZCD pin current. The NCP1608 features a powerful output driver on the DRV pin. The driver is capable of switching the gates of large MOSFETs efficiently because of its low source and sink impedances. The driver includes active and passive pull−down circuits to prevent the output from floating high when the NCP1608 is disabled. Design Procedure The design of a CrM boost PFC converter is discussed in many ON Semiconductor application notes. Table 1 lists some examples. This application note describes the design procedure for a 400 V, 100 W converter using the features of the NCP1608. A dedicated NCP1608 design tool that enables users to determine component values quickly is available at www.onsemi.com. Table 1. Additional Resources for the Design and Understanding of CrM Boost PFC Circuits Available at www.onsemi.com. AND8123 Power Factor Correction Stages Operating in Critical Conduction Mode AND8016 Design of Power Factor Correction Circuits Using the MC33260 AND8154 NCP1230 90 W, Universal Input Adapter Power Supply with Active PFC HBD853 Power Factor Correction Handbook DESIGN STEP 1: Define the Required Parameters The converter parameters are shown in Table 2. Table 2. CONVERTER PARAMETERS Parameter Name Symbol Value Units Minimum Line Input Voltage VacLL 85 Vac Maximum Line Input Voltage VacHL 265 Vac Minimum Line Frequency fline(MIN) 47 Hz Maximum Line Frequency fline(MAX) 63 Hz Output Voltage Vout 400 V Full Load Output Current Iout 250 mA Full Load Output Power Pout 100 W Maximum Output Voltage Vout(MAX) 440 V Minimum Switching Frequency fSW(MIN) 40 kHz h 92 % PF 0.9 − Minimum Full Load Efficiency Minimum Full Load Power Factor DESIGN STEP 2: Calculate the Boost Inductor Where L LL is the inductor value calculated at Vac LL. The value of the boost inductor (L) is calculated using Equation 1: Lv ǒ Ǔ V out Vac 2 @ * Vac @ h Ǹ2 Ǹ2 @ V @ P @ f out out SW(MIN) ǒ (eq. 1) Where L HL is the inductor value calculated at Vac HL. A value of 400 mH is selected. The inductance tolerance is ±15%. The maximum inductance (LMAX) value is 460 mH. Equation 2 is used to calculate the minimum frequency at full load. To ensure that the switching frequency exceeds the minimum frequency, L is calculated at both the minimum and maximum rms input line voltage: ǒ Ǔ 265 2 @ 400 * 265 @ 0.92 Ǹ2 + 509 mH L HL v Ǹ2 @ 400 @ 100 @ 40 k Ǔ 85 2 @ 400 * 85 @ 0.92 Ǹ2 L LL v + 581 mH Ǹ2 @ 400 @ 100 @ 40 k f SW + http://onsemi.com 3 ǒ Ǹ2 @ Vac Vac 2 @ h @ 1* 2 @ L MAX @ P out V out Ǔ (eq. 2) NCP1608BOOSTGEVB f SW(LL) + f SW(HL) + ǒ ǒ Ǔ Ǔ MOSFET Conduction Diode Conduction 85 2 @ 0.92 @ 1 * Ǹ2 @ 85 + 50.5 kHz 400 2 @ 460 m @ 100 265 2 @ 0.92 @ 1 * Ǹ2 @ 265 + 44.3 kHz 400 2 @ 460 m @ 100 IL(peak) DESIGN STEP 3: Size the Ct Capacitor t on(MAX) + 2 @ 460 m @ 100 + 13.8 ms 0.92 @ 85 2 (eq. 3) Ct w h @ Vac LL 2 @ V Ct(MAX) VZCD(WIND),off 0V VZCD(WIND),on VZCD VCL(POS) VZCD(ARM) VZCD(TRIG) VCL(NEG) (eq. 4) ton Where Icharge and VCt(MAX) are specified in the NCP1608 datasheet. To ensure that the controller sets the maximum on time to a value sufficient to deliver the required output power, the maximum Icharge and the minimum VCt(MAX) values are used in the calculations for Ct. From the NCP1608 datasheet: − VCt(MAX) = 4.775 V (minimum) To activate the ZCD detector of the NCP1608, the ZCD turns ratio is sized such that at least VZCD(ARM) (1.55 V maximum) is applied to the ZCD pin during all operating conditions (see Figure 4). The boost winding to ZCD winding turns ratio (N = NB:NZCD) is calculated using Equation 5. Nv 400 * ǒǸ2 @ 265Ǔ 1.55 R ZCD w Ǹ2 @ Vac HL I ZCD(MAX) @ N R ZCD w Ǹ2 @ 265 + 3.75 kW 10 m @ 10 (eq. 6) The value of RZCD and the parasitic capacitance of the ZCD pin determine when the ZCD winding signal is detected and the drive turn on begins. A large RZCD value creates a long delay before detecting the ZCD event. In this case, the controller operates in DCM and the PF is reduced. If the RZCD value is too small, the drive turns on when the drain voltage is high and efficiency is reduced. A popular strategy for selecting RZCD is to use the RZCD value that achieves minimum drain voltage turn on. This value is found experimentally. During the delay caused by RZCD and the ZCD pin capacitance, the equivalent drain capacitance (CEQ(drain)) discharges through the path shown in Figure 5. DESIGN STEP 4: Determine the ZCD Turns Ratio V ZCD(ARM) RZCD Delay A turns ratio of 10 is selected for this design. RZCD is connected between the ZCD winding and the ZCD pin to limit the ZCD pin current. This current must be limited below 10 mA. RZCD is calculated using Equation 6: A normalized value of 1 nF (±10%) provides sufficient margin. A value of 1.22 nF is selected for Total Harmonic Distortion (THD) reduction (see the Additional THD Reduction section of this application note for more information). V out * ǒǸ2 @ Vac HLǓ toff Figure 4. Realistic CrM Waveforms Using a ZCD Winding with RZCD and the ZCD Pin Capacitance 2 @ 100 @ 460 m @ 297 m + 860 pF 0.92 @ 85 2 @ 4.775 Nv 0V tdiode TSW − Icharge = 297 mA (maximum) Ct is equal to: Ct w 0V Minimum Voltage Turn on VZCD(WIND) Sizing Ct to an excessively large value causes the application to deliver excessive output power and reduces the control range at VacHL or low output power. It is recommended to size the Ct capacitor to a value slightly larger than that calculated by Equation 4: 2 @ P out @ L MAX @ I charge 0V Vdrain Vout The Ct capacitor is sized to set the maximum on time for minimum line input voltage and maximum output power. The maximum on time is calculated using Equation 3: 2 @ L MAX @ P out h @ Vac LL 2 0A IL(NEG) DRV fSW is equal to 50.5 kHz at VacLL and 44.3 kHz at VacHL. t on(MAX) + tz IL (eq. 5) + 16 http://onsemi.com 4 NCP1608BOOSTGEVB L IL Iin AC Line + EMI Filter Vout D + Cin CEQ(drain) Cbulk Figure 5. Equivalent Drain Capacitance Discharge Path CEQ(drain) is the combined parasitic capacitances of the MOSFET, the diode, and the inductor. Cin is charged by the energy discharged by CEQ(drain). The charging of Cin reverse biases the bridge rectifier and causes the input current (Iin) to decrease to zero. The zero input current causes THD to increase. To reduce THD, the ratio (tz / TSW) is minimized, where tZ is the period from when IL = 0 A to when the drive turns on. The ratio (tz / TSW) is inversely proportional to the square root of L. R out2 + R out2 + Ǔ 4 M @ 4.6 M + 25.3 kW 4.6 M @ 400 * 1 * 4 M 2.5 ǒ ǒ Rout1 and Rout2 form a resistor divider that scales down Vout before it is applied to the FB pin. The error amplifier adjusts the on time of the drive to maintain the FB pin voltage equal to the error amplifier reference voltage (VREF). The divider network bias current (Ibias(out)) selection is the first step in the calculation. The divider network bias current is selected to optimize the tradeoff of noise immunity and power dissipation. Rout1 is calculated using the optimized bias current and output voltage using Equation 7: V out I bias(out) (eq. 8) Vout R FB @ * 1 * R out1 VREF Ǔ Rout2 is selected as 25.5 kW for this design. Using the selected resistor, the resulting output voltage is calculated using Equation 9: DESIGN STEP 5: Set the FB, OVP, and UVP Levels R out1 + ǒ R out1 @ R FB V out + V REF @ R out1 @ ǒ V out + 2.5 @ 4 M @ Ǔ R out2 ) R FB )1 R out2 @ R FB (eq. 9) Ǔ 25.5 k ) 4.6 M ) 1 + 397 V 25.5 k @ 4.6 M The low bandwidth of the PFC stage causes overshoots during transient loads or during startup. The NCP1608 includes an integrated OVP circuit to prevent the output from exceeding a safe voltage. The OVP circuit compares VFB to the internal overvoltage detect threshold voltage to determine if an OVP fault occurs. The OVP detection voltage is calculated using Equation 10: (eq. 7) (eq. 10) ǒ A bias current of 100 mA provides an acceptable tradeoff of power dissipation to noise immunity. Ǔ V R ) R FB V out(OVP) + OVP @ V REF @ R out1 @ out2 )1 V REF R out2 @ R FB R out1 + 400 + 4 MW 100 m ǒ V out(OVP) + 1.06 @ 2.5 @ 4 M @ The output voltage signal is delayed before it is applied to the FB pin due to the time constant set by Rout1 and the FB pin capacitance. Rout1 must not be sized too large or this delay may cause overshoots of the OVP detection voltage. Rout2 is dependent on Vout, Rout1, and the internal feedback resistor (RFB, shown in the NCP1608 specification table). Rout2 is calculated using Equation 8: Ǔ 25.5 k ) 4.6 M ) 1 + 421 V 25.5 k @ 4.6 M The output capacitor (Cbulk) value is sized to be large enough so that the peak-to-peak output voltage ripple (Vripple(peak-peak)) is less than the OVP detection voltage. Cbulk is calculated using Equation 11: C bulk w P out 2 @ p @ V ripple(peak−peak) @ f line @ V out (eq. 11) Where fline = 47 Hz is the worst case for the ripple voltage and Vripple(peak-peak) < 42 V. C bulk w http://onsemi.com 5 100 + 20 mF 2 @ p @ 42 @ 47 @ 400 NCP1608BOOSTGEVB DESIGN STEP 6: Size the Power Components The value of Cbulk is selected as 68 mF to reduce Vripple(peak-peak) to less than 15 V. This results in a peak output voltage of 406.25 V, which is less than the peak output OVP detection voltage (421 V). The NCP1608 includes undervoltage protection (UVP). During startup, Cbulk charges to the peak of the ac line voltage. If Cbulk does not charge to a minimum voltage, the NCP1608 detects an UVP fault. The UVP detection voltage is calculated using Equation 12: ǒ (eq. 12) I L(peak) + 25.5 k ) 4.6 M ) 1 + 49 V 25.5 k @ 4.6 M I L(peak) + V out(UVP) + V UVP @ R out1 @ ǒ V out(UVP) + 0.31 @ 4 M @ Ǔ R out2 ) R FB )1 R out2 @ R FB The power components are sized such that there is sufficient margin to sustain the currents and voltages applied to them. At minimum line input voltage and maximum output power the inductor peak current is at the maximum, which causes the greatest stress to the power components. The components are referenced in Figure 3. 1. The inductor peak current (IL(peak)) is calculated using Equation 13: Ǔ Ǹ2 @ 2 @ P out h @ Vac Ǹ2 @ 2 @ 100 0.92 @ 85 (eq. 13) + 3.62 A The inductor rms current (IL(RMS)) is calculated using Equation 14: The UVP feature protects against open loop conditions in the feedback loop. If the FB pin is inadvertently floating (perhaps due to a bad solder joint), the coupling within the system may cause VFB to be within the regulation range (i.e. VUVP < VFB < VREF). The controller responds by delivering maximum power. The output voltage increases and over stresses the components. The NCP1608 includes a feature to protect the system if FB is floating. The internal pull-down resistor (RFB) ensures that VFB is below the UVP threshold if the FB pin is floating. If the FB pin floats during operation, VFB begins decreasing from VREF. The rate of decrease depends on RFB and the FB pin parasitic capacitance. As VFB decreases, VControl increases, which causes the on time to increase until VFB < VUVP. When VFB < VUVP, the UVP fault is detected and the controller is disabled. The sequence is depicted in Figure 6. I L(RMS) + 2 @ P out Ǹ3 @ Vac @ h I L(RMS) + 2 @ 100 + 1.48 A Ǹ3 @ 85 @ 0.92 (eq. 14) 2. The output diode (D) rms current (ID(RMS)) is calculated using Equation 15: I D(RMS) + 4 @ 3 ǸǸ2p@ 2 @ I D(RMS) + 4 @ 3 ǸǸ2p@ 2 @ P out (eq. 15) h @ ǸVac @ V out 100 + 0.75 A 0.92 @ Ǹ85 @ 400 The diode maximum voltage is equal to VOVP (421 V) plus the overshoot caused by parasitic contributions. For this evaluation board, the maximum voltage is 450 V. A 600 V diode provides a 25% derating factor. The MUR460 (4 A/600 V) diode is selected for this design. 3. The MOSFET (M) rms current (IM(RMS)) is calculated using Equation 16: VCC VCC(on) VCC(off) Ǹ ǒ ǓǸ ǒ ǒ Ǔ P out I M(RMS) + 2 @ @ Ǹ3 h @ Vac Vout Vout Loop is Opened ǒ VFB 100 I M(RMS) + 2 @ @ Ǹ3 0.92 @ 85 VREF VUVP 1* Ǹ2 @ 8 @ Vac 3 @ p @ V out Ǔ Ǔ (eq. 16) Ǹ2 @ 8 @ 85 1− +1.27 A 3 @ p @ 400 The MOSFET maximum voltage is equal to VOVP (421 V) plus the overshoot caused by parasitic contributions. For this evaluation board, the maximum voltage is 450 V. A 560 V MOSFET provides a 20% derating factor. The SPP12N50C3 (11.6 A/560 V) MOSFET is selected for this design. 4. The current sense resistor (Rsense) limits the maximum inductor peak current of the MOSFET and is calculated using Equation 17: VControl VEAH Ct(offset) UVP Fault Figure 6. UVP Operation if Loop is Opened During Operation R sense + V ILIM I L(peak) (eq. 17) Where VILIM is specified in the NCP1608 datasheet. http://onsemi.com 6 NCP1608BOOSTGEVB Once VCC reaches VCC(on), the internal references and logic of the NCP1608 turn on. The NCP1608 includes an undervoltage lockout (UVLO) feature that ensures that the NCP1068 remains enabled unless VCC decreases to less than VCC(off). This hysteresis ensures sufficient time for another supply to power VCC. The ZCD winding is a possible solution, but the voltage induced on the winding may be less than the required voltage. An alternative is to implement a charge pump to supply VCC. A schematic is illustrated in Figure 7. R sense + 0.5 + 0.138 W 3.62 The current sense resistor is selected as 0.125 W for decreased power dissipation. The resulting maximum inductor peak current is 4 A. Since the MOSFET continuous current rating is 7 A (for TC = 100°C as specified in the manufacturer’s datasheet) and the inductor saturation current is 4.7 A, the maximum peak inductor current of 4 A is sufficiently low. The power dissipated by Rsense is calculated using Equation 18: PR PR sense sense + I M(RMS) 2 @ R sense RZCD (eq. 18) C3 + 1.27 2 @ 0.125 + 0.202 W R1 5. The output capacitor (Cbulk) rms current is calculated using Equation 19: I C(RMS) + I C(RMS) + Ǹ Ǹ2 @ 32 @ P 2 out * I load(RMS) 2 9 @ p @ Vac @ V out @ h 2 Ǹ + (eq. 19) Cin Ǹ2@Vac * I CC(startup) Rstart DV C3 + CVcc V out * V CC N (eq. 21) The current that charges CVcc is calculated using Equation 22: ǒ (eq. 22) Ǔ V out I AUX + C3 @ f SW @ DV C3 + C3 @ f SW @ * V CC N For off−line ac-dc applications that require PFC, a 2-stage approach is typically used. The first stage is the CrM boost PFC. This supplies the 2nd stage, which is traditionally an isolated flyback or forward converter. This solution is cost−effective and exhibits excellent performance. During low output power conditions the PFC stage is not required and reduces efficiency. Advanced controllers, such as the NCP1230 and NCP1381 detect the low output power condition and shut down the PFC stage by removing PFC(VCC) (Figure 8). (eq. 20) Where ICC(startup) = 24 mA (typical). If CVcc is selected as a 47 mF capacitor and Rstart is selected as 660 kW, tstartup is equal to: t startup + + C3 stores the energy for the charge pump. R1 limits the current by reducing the rate of voltage change. DAUX supplies current to C3 when its cathode is negative. When its cathode is positive it limits the maximum voltage applied to VCC. The voltage change across C3 over one period is calculated using Equation 21: The typical method to charge the VCC capacitor (CVcc) to VCC(on) is to connect a resistor between Vin and VCC. The low startup current consumption of the NCP1608 enables most of the resistor current to charge CVcc during startup. The low startup current consumption enables faster startup times and reduces standby power dissipation. The startup time (tstartup) is approximated with Equation 20: @ V CC(on) NCP1608 8 FB VCC 2 7 Control DRV 3 6 Ct GND 4 5 CS ZCD Figure 7. The ZCD Winding Supplies VCC using a Charge Pump Circuit DESIGN STEP 7: Supply VCC Voltage CC D1 1 The value of Cbulk is calculated in Step 5 to ensure a ripple voltage that is sufficiently low to not trigger OVP. The value of Cbulk may need to be increased so that the rms current does not exceed the ratings of Cbulk. The voltage rating of Cbulk is required to be greater than Vout(OVP). Since Vout(OVP) is 421 V, Cbulk is selected to have a voltage rating of 450 V. CV DAUX Rstart Ǹ2 @ 32 @ 100 2 * 0.25 2 + 0.7 A 9 @ p @ 85 @ 400 @ 0.92 2 t startup + IAUX 47 m @ 12 + 3.57 s Ǹ2@85 * 24 m 660 k http://onsemi.com 7 NCP1608BOOSTGEVB D + 1 8 2 7 3 4 PFC(VCC) 1 8 2 7 6 3 6 5 4 5 + Cbulk VCC + + + + − NCP1230 NCP1608 Figure 8. Using the SMPS Controller to Supply Power to the NCP1608 DESIGN STEP 8: Limit the Inrush Current Dbypass The sudden application of the ac line voltage to the PFC pre−converter causes an inrush current and a resonant voltage overshoot that is several times the normal value. Resizing the power components to handle inrush current and a resonant voltage overshoot is cost prohibitive. 1. External Inrush Current Limiting Resistor A NTC (negative temperature coefficient) thermistor connected in series with the diode limits the inrush current (Figure 9). The resistance of the NTC decreases from a few ohms to a few milliohms as the NTC is heated by the I2R power dissipation. However, an NTC resistor may not be sufficient to protect the inductor and Cbulk from inrush current during a brief interruption of the ac line voltage, such as during ac line dropout and recovery. 2. Startup Bypass Rectifier A rectifier is connected from Vin to Vout (Figure 10). This bypasses the inductor and diverts the startup current directly to Cbulk. Cbulk is charged to the peak ac line voltage without resonant overshoot and without excessive inductor current. After startup, Dbypass is reverse biased and does not interfere with the boost converter. Vin + NCP1608 Figure 10. Use a Second Diode to Route the Inrush Current Away from the Inductor DESIGN STEP 9: Develop the Compensation Network The pre−converter is compensated to ensure stability over the input voltage and output power range. To compensate the loop, a compensation network is connected between the Control and ground pins. To ensure high PF, the bandwidth of the loop is set below 20 Hz. A type 2 compensation network is selected for this design to increase the phase margin. The type 2 compensation network is shown in Figure 11. Vout NTC Vin Rout1 Vout RFB Rout2 Figure 9. Use a NTC to Limit the Inrush Current Through the Inductor − + + NCP1608 E/A FB + Vac Vout Vac gm VREF Control CCOMP RCOMP1 VControl Compensation Network CCOMP1 Figure 11. Type 2 Compensation Network http://onsemi.com 8 NCP1608BOOSTGEVB The type 2 network is composed of CCOMP, CCOMP1, and RCOMP1. CCOMP1 sets the crossover frequency (fCROSS) and is calculated using Equation 23: gm C COMP1 + 2 @ p @ f CROSS (eq. 23) 1 2 @ p @ f zero @ C COMP R COMP1 + 1 + 19.3 kW 2 @ p @ 2.5 @ 3.3 m (eq. 24) RCOMP1 is selected as 20 kW. CCOMP is used to filter high frequency noise and is set to between 1/10 and 1/5 of CCOMP1. For this design, CCOMP is selected to be 1/5 of CCOMP1. For this design, fCROSS is set to 5 Hz at the average input voltage (175 Vac) to decrease THD and gm is specified in the NCP1608 datasheet: C COMP1 + R COMP1 + ǒǓ C COMP + 1 @ 3.3 m + 0.66 mF 5 110 m + 3.5 mF 2@p@5 CCOMP is selected as 0.68 mF. The phase margin and crossover frequency change with the ac line voltage. It is critical that the gain and phase are measured for all operating conditions. The measurement setup using a network analyzer is shown in Figure 12. A normalized value of 3.3 mF is selected, which sets fCROSS to 5.3 Hz. The addition of RCOMP1 causes a zero in the loop response. The zero frequency (fzero) is typically set to half the crossover frequency, which is 2.5 Hz for this case. RCOMP1 is calculated using Equation 24: Ch A High−Voltage (> 450 V) Isolation Probe Ch B High−Voltage (> 450 V) Isolation Probe Network Analyzer D L Vout Isolator RZCD + AC Line EMI Filter 1 kW Rout1 1 Cin 2 Rout2 3 Ct 4 NCP1608 FB VCC Control DRV Ct GND CS ZCD Load VCC 8 7 + M Cbulk 6 5 CCOMP Rsense Figure 12. Gain-Phase Measurement Setup for a Boost PFC Pre−Converter 1. Improve the THD/PF at Maximum Output Power by Increasing the On Time at the Zero Crossing: There is a tradeoff of transient response for PF and THD. The low bandwidth of the feedback loop reduces the Control pin ripple voltage. The reduction of the Control pin ripple voltage increases PF and reduces THD, but increases the magnitude of overshoots and undershoots. One disadvantage of constant on time CrM control is that at the zero crossing of the ac line, the instantaneous input voltage is not large enough to store sufficient energy in the inductor during the constant on time. Minimal energy is processed and “zero crossing distortion” is produced as shown in Figure 13. Additional THD Reduction The constant on time architecture of the NCP1608 provides flexibility in optimizing each design. The following design guidelines provide methods to further improve PF and THD. http://onsemi.com 9 NCP1608BOOSTGEVB Vin (100V/div) Iin (500mA/div) Vout (10V/div, ac coupled) Zero Crossing Distortion Figure 13. Full Load Input Current (Vin = 230 Vac 50 Hz, Iout = 250 mA) reduces the instantaneous input voltage at which the distortion begins. This method is implemented by connecting a resistor from Vin to Ct as shown in Figure 14. The resistor current (ICTUP) is proportional to the instantaneous line voltage and is summed with Icharge to increase the charging current of Ct. ICTUP is maximum at the peak of Vin and is approximately zero at the zero crossing. The zero crossing distortion increases the THD and decreases the PF of the pre-converter. To meet IEC61000-3-2 requirements, this is generally not an issue as the NCP1608 reduces input current distortion with sufficient margin. If improved THD or PF is required, then zero crossing distortion must be reduced. To reduce the zero crossing distortion, the on time is increased as the instantaneous input voltage is decreasing to zero. This increases the time for the inductor current to build up and L Vin I CTUP + + AC Line Cin V in R CTUP VDD RCTUP VControl PWM − + Icharge Ct ton DRV Ct Ct(offset) Figure 14. .Add RCTUP to Modulate the On Time and Reduce Zero Crossing Distortion in Figure 15. This reduces the frequency variation over the ac line cycle. The tradeoff is that the standby power dissipation is increased by RCTUP. The designer must balance the desired THD and PF performance with the standby power dissipation requirements. The increased charging current at the peak of Vin enables the increased sizing of the Ct capacitor without reducing the control range at VacHL or low output power. The larger value of the Ct capacitor increases the on time near the zero crossing and reduces the zero crossing distortion as shown http://onsemi.com 10 NCP1608BOOSTGEVB Vac(t) with RCTUP ton no RCTUP no RCTUP fSW with RCTUP time Figure 15. On Time and Switching Frequency With and Without RCTUP The dependency of THD on RCTUP is illustrated in Figure 16. 14 Vout 12 VFB RCTUP = open Ct = 1 nF 10 THD (%) Vout VREF 8 VControl 6 RCTUP = 1.5 MW Ct = 1.22 nF 4 Ct(offset) 2 0 DRV 85 115 145 175 Vin (Vac) 205 235 265 Figure 16. Dependency of THD on RCTUP (Iout = 250 mA) Figure 17. Required On Time Less Than the Minimum On Time This sequence increases the input current distortion. There are two solutions to improve THD/PF at maximum input voltage or low output current: 1. Properly size the Ct capacitor. As previously mentioned, the Ct capacitor is sized to set the maximum on time for minimum line input voltage and maximum output power. Sizing Ct to an excessively large value reduces the control range at VacHL or low output power. 2. Compensate for propagation delays. If optimizing the Ct capacitor does not achieve the desired performance, then it may be necessary to compensate for the PWM propagation delay by connecting a resistor (RCT) in series with Ct. When the Ct voltage reaches the VControl setpoint, the PWM comparator sends a signal to end the on time of the driver as shown in Figure 18. 2. Improve the THD/PF at Maximum Input Voltage or Low Output Current: If the required on time at maximum input voltage or low output current is less than the minimum on time (tPWM), then DRV pulses must be skipped to prevent excessive power delivery to the output. This results in the following sequence: 1. The excessive on time causes VControl to decrease to Ct(offset). 2. When VControl < Ct(offset), the drive is disabled. 3. The drive is disabled and Vout decreases. 4. As Vout decreases, VControl increases. 5. The sequence repeats. Figure 17 depicts the sequence: http://onsemi.com 11 NCP1608BOOSTGEVB VControl Control Iswitch VDD Icharge Ct VCt(off) RCT PWM − + Driver Vgate DRV RDRV DRV Rsense Ct(offset) Ct Figure 18. Block Diagram of the Propagation Delay Components A value of RCT = 365 W compensates for the propagation delays. Figure 20 shows the decrease of THD at VacHL and low output power by compensating for the propagation delay. There is a delay (tdelay) from when VCt(off) is reached to when the MOSFET completely turns off. tdelay is caused by the propagation delay of the PWM comparator (tPWM) and the time for the gate voltage of the MOSFET to decrease to zero (tgate). The delays are illustrated in Figure 19. 50 40 VCt(off) RCT = 0 W THD (%) Ct tPWM Vgate 30 DRV Pulse Skipping Begins 20 RCT = 365 W 10 0 25 30 35 Pout (W) Iswitch The total delay is calculated using Equation 25: (eq. 25) tdelay increases the effective on time of the MOSFET. If a resistor (RCT) is connected in series with the Ct capacitor, then the total on time reduction is calculated using Equation 26: 50 40 (eq. 26) THD (%) DV RCT + Ct @ R CT DI RCT The value of RCT to compensate for the propagation delay is calculated using Equation 27: R CT + t delay Ct (eq. 27) 30 DRV Pulse Skipping Begins RCTUP = open RCT = 0 W Ct = 1 nF 20 10 The NCP1608 datasheet specifies the maximum tPWM as 130 ns. tgate is a dependent on the gate charge of the MOSFET and RDRV. For this demo board, the gate delay is measured as 230 ns. R CT + 50 Both THD reduction techniques can be combined to decrease the THD for the entire output power range. Figure 21 shows the decreased THD at the maximum input voltage across the output power range by decreasing zero crossing distortion and by compensating for the propagation delay. Figure 19. Turn Off Propagation Delays Dt on + Ct @ 45 Figure 20. Low Output Power THD Reduction with RCT (Vin = 265 Vac 50 Hz, RCTUP = open, Ct = 1 nF) tgate tdelay t delay + t PWM ) t gate 40 0 RCTUP = 1.5 MW RCT = 365 W Ct = 1.22 nF 25 35 45 65 55 Pout (W) 75 85 95 Figure 21. THD Reduction with RCTUP and RCT (Vin = 265 Vac 50 Hz) 360 n + 360 W 1n http://onsemi.com 12 NCP1608BOOSTGEVB Design Results The completed evaluation board schematic is shown in Figure 22. Figure 22. NCP1608BOOSTGEVB Evaluation Board Schematic − The input power, PF, and THD are measured using a PM3000A power meter − The output voltage is measured using a HP34401A multimeter − The output current is set using a PLZ1003WH electronic load − The output current is measured using a HP34401A multimeter − The output power is calculated by multiplying the output voltage and output current The bill of materials (BOM), layout, and summary of boost equations are shown in Appendix 1, Appendix 2, and Appendix 3 respectively. This pre−converter exhibits excellent THD (Figure 23 and Figure 24), PF (Figure 25), and efficiency (Figure 26). All measurements are performed with the following conditions: − After the board is operated at full load and minimum line input voltage for 30 minutes − At an ambient temperature of 25°C, open frame, and without forced air flow http://onsemi.com 13 NCP1608BOOSTGEVB 0.7 12 0.6 Pout = 50 W 10 THD (%) HARMONIC CURRENT (A) 14 8 6 Pout = 100 W 4 2 0 80 130 180 230 0.3 IEC61000−3−2 Class D Limits 0.2 0.1 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 Nth HARMONIC Figure 23. THD vs. Input Voltage Figure 24. Individual Harmonic Current 100 1.00 Pout = 100 W 0.98 98 Pout = 50 W EFFICIENCY (%) 0.97 0.96 PF Pin = 75 W 0.4 Vin (Vac) 0.99 0.95 0.94 0.93 96 Pout = 100 W 94 Pout = 50 W 92 0.92 0.91 0.90 0.5 0 280 115 Vac 60 Hz 230 Vac 50 Hz 80 115 150 185 220 255 290 90 80 115 150 185 220 255 Vin (Vac) Vin (Vac) Figure 25. PF vs. Input Voltage Figure 26. Efficiency vs. Input Voltage http://onsemi.com 14 290 NCP1608BOOSTGEVB Input Current and Output Voltage The input current and output voltage ripple are shown in Figure 27. The overvoltage protection is observed by starting up the pre-converter with no load as shown in Figure 28. The NCP1608 detects an OVP fault when Vout reaches 421 V and restarts when Vout decreases to 410 V. Vin (50V/div) Iin (1A/div) Vout (10V/div, ac coupled) Figure 27. Input Current and Output Voltage Ripple (Vin = 115 Vac 60 Hz, Iout = 250 mA) VCC (10V/div) VDRV (10V/div) Vout (100V/div) Vin (100V/div) Figure 28. Startup Transient Showing OVP Detection and Recovery (Vin = 115 Vac 60 Hz, Iout = 0 mA) http://onsemi.com 15 NCP1608BOOSTGEVB Frequency Response crossover frequency is 2 Hz and the phase margin is 71°. Figure 30 shows that at maximum input voltage, the crossover frequency is 10 Hz and the phase margin is 53°. 100 150 80 120 60 90 Phase GAIN (dB) 40 Phase Margin 20 30 0 0 −20 Gain −40 −30 −60 −90 −60 −80 −100 60 PHASE (degrees) The frequency response is measured at the minimum and maximum input voltages and maximum output power. Figure 29 shows that at minimum input voltage, the 1 fCROSS 10 FREQUENCY (Hz) −120 −150 100 Figure 29. Frequency Response Vin = 85 Vac 60 Hz Iout = 250 mA 100 150 80 120 60 GAIN (dB) 40 Phase Margin 20 60 30 0 0 Gain −20 −30 PHASE (degrees) 90 Phase −40 −60 −60 −90 −80 −100 −120 1 10 fCROSS −150 100 FREQUENCY (Hz) Figure 30. Frequency Response Vin = 265 Vac 50 Hz Iout = 250 mA http://onsemi.com 16 NCP1608BOOSTGEVB Floating Pin Protection (FPP) Jumper Figure 31. If J1 is removed during operation, the drive is disabled as shown in Figure 32. J1 is for FPP evaluation purposes only and should not be included in manufactured systems. The evaluation board includes a jumper (J1) between the FB pin and the feedback network to demonstrate the FPP feature of the NCP1608. If J1 is removed before applying the line input voltage, the drive is never enabled as shown in Vin (100V/div) VCC (5V/div) VDRV (5V/div) Vout (100V/div) No DRV Pulses Figure 31. Startup with Jumper Removed (Vin = 265 Vac 50 Hz, Iout = 0 mA) t(4ms/div) Vin (100V/div) DRV Pulses Stop Vout (100V/div) VCC (5V/div) VDRV (5V/div) t(8μs/div) (Zoomed In) Figure 32. Removing the Jumper During Operation (Vin = 265 Vac 50 Hz, Iout = 250 mA) http://onsemi.com 17 NCP1608BOOSTGEVB The evaluation board can be configured for THD reduction or power dissipation reduction. Table 3 shows the configuration results. Table 3. EVALUATION BOARD CONFIGURATION RESULTS Efficiency (Pout = 100 W) THD (Pout = 100 W) Ct (RCT = 0 W) Shutdown Power Dissipation (VFB = 0 V) 115 Vac 230 Vac 115 Vac 230 Vac (Vin = 265 Vac 50 Hz) 60 Hz 50 Hz 60 Hz 50 Hz open 1 nF 224 mW 93.5% 95.7% 8.4% 12.5% 1.5 MW 1.22 nF 294 mW 93.5% 95.5% 4.4% 6.2% RCTUP Safety Precautions The evaluation board includes the following unpopulated footprints to enable user experimentation: 1. CCS to add a decoupling capacitor to the CS pin. 2. CZCD to add a decoupling capacitor to the ZCD pin. 3. DDRV to add a diode for faster turn off of Q1. 4. DVCC to add a diode to clamp VCC. 5. ROUT2B to add a resistor for a more accurate output voltage. 6. RS3 to add a resistor for a more accurate inductor peak current limit or to reduce the heating of the current sense resistors. Since the FPP feature is only intended to protect the system in the case of a floating FB pin, care must be taken when removing the jumper. Do not attach any wires to the jumper pins with the jumper removed. Connecting wires to the FB pin couples excessive noise to the FB pin. This prevents the correct operation of FPP and causes maximum power to be delivered to the output. This can cause excessive voltage to be applied to Cbulk. Always wear proper eye protection when the jumper is removed. The jumper is located next to high voltage components. Do not remove the jumper during operation with bare fingers or non-insulated metal tools. Summary Layout Considerations A universal input voltage 100 W converter is designed using the boost topology. The converter is implemented with the NCP1608. Over the input voltage range and with an output power of 100 W, the PF, THD, and efficiency are measured as greater than 0.97, less than 8%, and greater than 92% respectively. The converter complies with IEC61000−3−2 Class D limits for an input power of 75 W. The converter is stable over the input voltage range with a measured phase margin greater than 50 degrees. Finally, the overvoltage protection and floating pin protection features protect the converter from excessive output voltage. The evaluation board is designed to showcase the features and flexibility of the NCP1608. This design is a guideline only and does not guarantee performance for any manufacturing or production purposes. Careful consideration must be given to the placement of components during layout of switching power supplies. Noise generated by the large voltages and currents can be coupled to the pins of the NCP1608. The following guidelines reduce the probability of excessive coupling: 1. Place the following components as close as possible to the NCP1608: a. Ct capacitor b. VCC decoupling capacitor c. Control pin compensation components 2. Minimize trace length, especially for high current loops. 3. Use wide traces for high current connections. 4. Use a single point ground connection between power ground and signal ground. http://onsemi.com 18 NCP1608BOOSTGEVB Table 4. BILL OF MATERIALS* Manufacturer Manufacturer Part Number Substitution Allowed Vishay KBL06-E4/51 Yes Radial EPCOS B32923C3474M Yes 5% 1206 TDK Corporation C3216C0G1H822J Yes 68 mF 20% Radial United Chemi−Con EKXG451ELL680MMN3S Yes Capacitor, Ceramic, SMD, 25 V 0.68 mF 10% 1206 TDK Corporation C3216X7R1E684K Yes 1 Capacitor, Ceramic, SMD, 25 V 3.3 mF 10% 1206 TDK Corporation C3216X7R1E335K Yes CCS, CZCD 2 Capacitor, Ceramic, SMD open − 1206 − − − CIN 1 Capacitor, EMI Suppression, 305 Vac 0.1 mF 20% Radial EPCOS B32921A2104M Yes CT1 1 Capacitor, Ceramic, SMD, 50 V 1 nF 10% 1206 Yageo CC1206KRX7R9BB102 Yes CT2 1 Capacitor, Ceramic, SMD, 50 V 220 pF 10% 1206 Yageo CC1206KRX7R9BB221 Yes Designator Value Tolerance Qty Description BRIDGE 1 Bridge Rectifier, 4 A, 600 V Footprint − − KBL C1, C2 2 Capacitor, EMI Suppression, 305 Vac 0.47 mF 20% C3 1 Capacitor, Ceramic, SMD, 50 V 8.2 nF CBULK 1 Capacitor, Electrolytic, 450 V CCOMP 1 CCOMP1 CVCC 1 Capacitor, Electrolytic, 25 V 47 mF 20% Radial Panasonic EEU-FC1E470 Yes CVCC2 1 Capacitor, Ceramic, SMD, 50 V 0.1 mF 10% 1206 Yageo CC1206KRX7R9BB104 Yes D1 1 Diode, Switching, 100 V − − SOD123 ON Semiconductor MMSD4148T1G No DAUX 1 Diode, Zener, 18 V − − SOD123 ON Semiconductor MMSZ4705T1G No DBOOST 1 Diode, Ultrafast, 4 A, 600 V − − Axial ON Semiconductor MUR460RLG No DDRV 1 Diode, Switching open − SOD123 − − − DVCC 1 Diode, Zener open − SOD123 − − − F1 1 Fuse, SMD, 2 A, 600 V − − SMD Littelfuse 0461002.ER Yes J1 1 Header 1 Row of 2, 100 mil − − 2.54 mm 3M 929400-01-36-RK Yes J2, J3 2 Connector, 156 mil 3 pin − − 156 mil MOLEX 26−60−4030 Yes L1 1 Inductor, Radial, 4 A 180 mH 10% Radial Coilcraft PCV-2-184-05L No L2 1 Line Filter, 2.7 A 4.7 mH − Through Hole Panasonic ELF-20N027A Yes LBOOST 1 Inductor, NB:NZCD = 10:1 400 mH − Custom Coilcraft JA4224−AL No MECHA− NICAL 1 Shorting Jumper on J1 − − − 3M 929955-06 Yes MECHA− NICAL 1 Heatsink − − TO−220 Aavid 590302B03600 Yes MECHA− NICAL 1 Screw, Phillips, 4−40, ¼”, Steel − − − Building Fasteners PMSSS 440 0025 PH Yes MECHA− NICAL 1 Nut, Hex 4−40, Steel − − − Building Fasteners HNSS440 Yes MECHA− NICAL 1 Shoulder Washer #4, Nylon − − − Keystone 3049 Yes MECHA− NICAL 1 TO 220 Thermal Pad, 9 mil − − − Wakefield 173-9-240P Yes MECHA− NICAL 4 Standoffs, Hex 4−40, 0.75”, Nylon − − − Keystone 4804K Yes MECHA− NICAL 4 Nut, Hex 4−40, Nylon − − − Building Fasteners NY HN 440 Yes *All products listed are Pb−free http://onsemi.com 19 NCP1608BOOSTGEVB Table 4. BILL OF MATERIALS* Manufacturer Manufacturer Part Number Substitution Allowed EPCOS B57238S479M Yes TO−220 Infineon SPP12N50C3 Yes 1% 1206 Vishay CRCW1206100RFKEA Yes 20 kW 1% 1206 Vishay CRCW120620K0FKEA Yes Resistor, 0.25 W Axial 510 W 5% Axial Yageo CFR-25JB-510R Yes Resistor, SMD 0W − 1206 Vishay CRCW12060000Z0EA Yes 2 Resistor, 0.25 W Axial 750 kW 5% Axial Yageo CFR-25JB-750K Yes RDRV 1 Resistor, SMD 10 W 1% 1206 Vishay CRCW120610R0FKEA Yes RO1A, RO1B 2 Resistor, SMD 2 MW 1% 1206 Vishay CRCW12062M00FKEA Yes ROUT2A 1 Resistor, SMD 25.5 kW 1% 1206 Vishay CRCW120625K5FKEA Yes ROUT2B 1 Resistor, SMD open − 1206 − − - RS1, RS2 2 Resistor, SMD, 1 W 0.25 W 1% 2512 Vishay WSL2512R2500FEA Yes RS3 1 Resistor, SMD open − 2512 − − - RSTART1 RSTART2 2 Resistor, 0.25 W Axial 330 kW 5% Axial Yageo CFR-25JB-330K Yes RZCD 1 Resistor, 0.25 W Axial 100 kW 5% Axial Yageo CFR-25JB-100K Yes U1 1 CrM PFC Controller NCP1608 − SOIC−8 ON Semiconductor NCP1608BDR2G No Value Tolerance Footprint 4.7 W 20% Radial MOSFET, N−Channel, 11.6 A, 560 V − − 1 Resistor, SMD 100 W RCOMP1 1 Resistor, SMD RCS 1 RCT 1 RCTUP1, RCTUP2 Designator Qty Description NTC 1 Thermistor, Inrush Current Limiter Q1 1 R1 *All products listed are Pb−free Figure 33. Evaluation Board Photo http://onsemi.com 20 NCP1608BOOSTGEVB LAYOUT Figure 34. Top View of the Layout Figure 35. Bottom View of the Layout http://onsemi.com 21 NCP1608BOOSTGEVB TEST PROCEDURE FOR THE NCP1608BOOSTGEVB EVALUATION BOARD Required Equipment • • • • • 15. Repeat steps 9-13 with the ac source set to 115 Vac / 60 Hz, 230 Vac / 50 Hz, 265 Vac / 50 Hz. Verify the results are within the limits of Table 5. 16. Turn off the ac source. 17. Since high voltage will be present after the voltage is removed, wait for the dc voltmeter to show approximately 0 V before continuing. 18. Disconnect the ac source. 19. Disconnect the oscilloscope. 20. Disconnect the electronic load. 21. Disconnect both multimeters. 22. End of test. (*Equivalent test equipment may be substituted.) *Chroma 61604 AC Power Source *Voltech PM3000A Power Analyzer 2× *Agilent 34401A Multimeter *Chroma 6314 Electronic Load with *Chroma 63108 High Voltage Module *Tektronix TDS5034B Oscilloscope with *Tektronix P5205 Differential Probes Test Procedure 1. Ensure that there is a jumper on J1. If not, place a jumper on J1 for the remainder of the test procedure. 2. Connect the electronic load with high voltage module to the output labeled “400 V, 100 W”. 3. Connect one of the multimeters in series with the output and load and set it to measure current. 4. Connect the second multimeter to the output and set it to measure voltage. 5. Connect the oscilloscope with differential probes to the output and set it to measure output ripple and frequency. 6. Connect the ac power source and power analyzer to the terminals labeled “Input”. Set the current compliance limit to 1.8 A. 7. Set the ac power source to 85 Vac / 60 Hz. 8. Set the high voltage electronic load to 250 mA. 9. Turn the AC source on. 10. Wait 10 seconds, and then check the output voltage (VOUT) using the corresponding multimeter. Verify it is within the limits of Table 5. 11. Measure power factor (PF) and input power (PIN) using the power analyzer. 12. Measure the peak-to-peak voltage and frequency of the output ripple using the oscilloscope. 13. Measure IOUT using the corresponding multimeter. 14. Calculate efficiency (h) using the equation: h+ I OUT V OUT P IN Table 5. DESIRED RESULTS For 85 Vac / 60 Hz input VOUT = 397 ±15 V PF > 0.99 Output Ripple Voltage < 20 VPP Output Ripple Frequency = 120 Hz sine wave h > 90% For 115 Vac / 60 Hz input VOUT = 397 ±15 V PF > 0.99 Output Ripple Voltage < 20 VPP Output Ripple Frequency = 120 Hz sine wave h > 90% For 230 Vac / 50 Hz input VOUT = 397 ±15 V PF > 0.95 Output Ripple Voltage < 20 VPP Output Ripple Frequency = 100 Hz sine wave h > 90% For 265 Vac / 50 Hz input VOUT = 397 ±15 V PF > 0.95 Output Ripple Voltage < 20 VPP Output Ripple Frequency = 100 Hz sine wave 100% h > 90% http://onsemi.com 22 NCP1608BOOSTGEVB Figure 36. Test Setup http://onsemi.com 23 NCP1608BOOSTGEVB Table 6. SUMMARY OF BOOST EQUATIONS Components are identified in Figure 3 Input rms Current P out h @ Vac h (the efficiency of only the PFC stage) is generally in the range of 90 − 95%. Vac is the rms ac line input voltage. Ǹ2 @ 2 @ P out h @ Vac The maximum inductor peak current occurs at the minimum line input voltage and maximum output power. Iac + Inductor Peak Current I L(peak) + Inductor Value Vac 2 @ Lv ǒ Ǔ Ǹ2 @ V @ P @ f out out SW(MIN) On Time t on + 2 @ L @ P out h @ Vac 2 The maximum on time occurs at the minimum line input voltage and maximum output power. t on The off time is a maximum at the peak of the ac line voltage and approaches zero at the ac line zero crossings. Theta (q) represents the angle of the ac line voltage. Off Time t off + Vout Vac@Ťsin qŤ@Ǹ2 Switching Frequency f SW + ǒ Ct w Output Voltage and Output Divider V out * ǒǸ2 @ Vac HLǓ Ǹ2 @ Vac HL I ZCD(MAX) @ (N B : N ZCD) ǒ R FB @ Output Voltage Ripple and Output Capacitor Value Ǔ ǒǒ ǒ R out1 @ R FB Vout VREF Ǔ * 1 * R out1 ǒ VOVP V REF Ǔ Ǔǒ Ǔ VOVP/VREF and VOVP(HYS) are shown in the specification table. Ǔ R out2 ) R FB @ V REF −V OVP(HYS) @ R out1 @ )1 R out2 @ R FB V ripple(peak−peak) t 2 @ ǒV out(OVP) * V outǓ I C(RMS) + Where VREF is the internal reference voltage and RFB is the pull− down resistor used for FPP. VREF and RFB are shown in the specification table. Ibias(out) is the bias current of the output voltage divider. R out2 ) R FB )1 R out2 @ R FB V OVP R ) R FB @ V REF @ R out1 @ out2 )1 V REF R out2 @ R FB C bulk w Output Capacitor rms Current Where IZCD(MAX) is maximum rated current for the ZCD pin (10 mA). V out I bias(out) R out2 + V out(OVPL) + Where VacHL is the maximum line input voltage. VZCD(ARM) is shown in the specification table. V ZCD(ARM) V out + V REF @ R out1 @ V out(OVP) + Where VacLL is the minimum line input voltage and LMAX is the maximum inductor value. Icharge and VCt(MAX) are shown in the specification table. h @ Vac LL 2 @ V Ct(MAX) R ZCD w R out1 + Output Voltage OVP Detection and Recovery Ǔ 2 @ P out @ L MAX @ I charge N B : N ZCD v Resistor from ZCD Winding to the ZCD pin *1 Vac 2 @ h Vac @ |sin q| @ Ǹ2 @ 1* 2 @ L @ P out V out On Time Capacitor Inductor Turns to ZCD Turns Ratio fSW(MIN) is the minimum desired switching frequency. The maximum L is calculated at both the minimum line input voltage and maximum line input voltage. V out * Vac @ h Ǹ2 P out 2 @ p @ V ripple(peak−peak) @ f line @ V out Ǹ Ǹ2 @ 32 @ P 2 out * I load(RMS) 2 9 @ p @ Vac @ V out @ h 2 http://onsemi.com 24 Where fline is the ac line frequency and Vripple(peak−peak) is the peak−to− peak output voltage ripple. Use fline = 47 Hz for universal input worst case. Where Iload(RMS) is the rms load current. NCP1608BOOSTGEVB Table 6. SUMMARY OF BOOST EQUATIONS Components are identified in Figure 3 (Continued) Output Voltage UVP Detection ǒ V out(UVP) + V UVP @ R out1 @ Inductor rms Current Output Diode rms Current MOSFET rms Current I L(RMS) + I D(RMS) + 4 @ 3 ǒ ǸǸ2p@ 2 @ Ǔ Ǹ R sense + PR Type 1 Compensation sense R out2 @ R FB Ǔ )1 VUVP is shown in the specification table. 2 @ P out Ǹ3 @ Vac @ h P out I M(RMS) + 2 @ @ Ǹ3 h @ Vac Current Sense Resistor R out2 ) R FB P out h @ ǸVac @ V out 1* ǒ Ǹ2 @ 8 @ Vac 3 @ p @ V out Ǔ V ILIM I L(peak) VILIM is shown in the specification table. + I M(RMS) 2 @ R sense gm C COMP + 2 @ p @ f CROSS Where fCROSS is the crossover frequency and is typically less than 20 Hz. gm is shown in the specification table. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 http://onsemi.com 25 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative EVBUM2162/D