TH09/2479 TH97/2478 IATF 0113686 SGS TH07/1033 www.eicsemi.com FR801 - FR805 FAST RECOVERY RECTIFIER DIODES TO-220AC PRV : 50 - 600 Volts Io : 8.0 Amperes 0.154(3.91)DIA. 0.148(3.74) 0.415(10.54)MAX. FEATURES : * * * * * * * 0.113(2.87) 0.103(2.62) High current capability High surge current capability High reliability Low reverse current Low forward voltage drop Fast switching for high efficiency Pb / RoHS Free 0.185(4.70) 0.175(4.44) 0.055(1.39) 0.045(1.14) 0.145(3.68) 0.135(3.43) 0.635(16.13) 0.625(15.87) 0.603(15.32) 0.573(14.55) 0.350(8.89) 0.330(8.39) 1 2 0.160(4.06) 0.140(3.56) PIN 1 0.560(14.22) 0.530(13.46) CASE PIN 2 MECHANICAL DATA : 0.037(0.94) 0.027(0.68) 0.205(520) 0.195(4.95) * Case : Epoxy, Molded * Lead Temperature for Soldering Purposes: 260°C Max. for 10 Seconds * Polarity: As marked * Mounting Position: Any * Weight : 2.24 grams (Approximately) 0.022(0.56) 0.014(0.36) Dimensions in inches and ( millimeters ) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. RATING SYMBOL FR801 FR802 FR803 FR804 FR805 UNIT Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 400 600 V Maximum RMS Voltage VRMS 35 70 140 280 420 V Maximum DC Blocking Voltage VDC 50 100 200 400 600 V Maximum Average Forward Current IF(AV) 8.0 A IFSM 150 A Maximum Peak Forward Voltage at I F = 8 A VF 1.3 V Maximum Reverse Current at Tc = 25 °C IR 10 μA Rated DC Blocking Voltage Tc = 100 °C IR(H) 150 μA Half-Wave Resistive Load Tc = 100 °C Peak Forward Surge Current 8.3ms Single half sine wave Superimposed on rated load (JEDEC Method) Maximum Reverse Recovery Time ( Note 1 ) Trr Typical Junction Capacitance( Note 2) CJ 70 pF TJ, TSTG - 65 to + 175 °C Operating and Storage Temperature Range 150 250 ns Notes : (1) Reverse Recovery Test Conditions : I F = 0.5 A, IR = 1.0 A, Irr = 0.25 A. (2) Measured at 1.0MHz and applied reverse voltage of 4.0V. Page 1 of 2 Rev. 02 : July 28, 2006 TH09/2479 TH97/2478 IATF 0113686 SGS TH07/1033 www.eicsemi.com RATING AND CHARACTERISTIC CURVES ( FR801 - FR805 ) FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 Ω Trr 10 Ω + 0.5 A D.U.T. + 0 PULSE GENERATOR ( NOTE 2 ) 50 Vdc (approx) 1Ω - 0.25 A OSCILLOSCOPE ( NOTE 1 ) - 1.0 A SET TIME BASE FOR 50/100 ns/cm NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF. 1 cm 2. Rise time = 10 ns max., Source Impedance = 50 ohms. 3. All Resistors = Non-inductive Types. FIG.2 - FORWARD CURRENT DERATING CURVE FIG.3 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 150 PEAK FORWARD SURGE CURRENT, (A) AVERAGE FORWARD CURRENT, (A) 10 8 6 4 60Hz Resistive load or Inductive load 2 0 0 25 50 75 100 125 150 90 60 30 0 175 8.3 ms Single Half Sine Wave JEDEC Method 120 1 2 CASE TEMPERATURE, ( °C) 4 6 10 20 40 60 100 NUMBER OF CYCLES AT 60Hz FIG.4 - TYPICAL INSTANTANEOUS FORWARD FIG.5 - TYPICAL REVERSE CHARACTERISTICS CHARACTERISTICS 10 INSTANTANEOUS REVERSE CURRENT, (μA) INSTANTANEOUS FORWARD CURRENT, (A) 100 10 1 0.1 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, (V) Page 2 of 2 1.8 1.0 0.1 0.01 0 20 40 60 80 100 120 140 PERCENT OF RATED REVERSE VOLTAGE, (%) Rev. 02 : July 28, 2006