Specifications

NEXT
FIND IT
Table of Contents
CLICK FOR PDF FILE
CLICK FOR PDF FILE
CLICK FOR PDF FILE
OVERVIEW –
Inductive Proximity Sensors
CYLINDRICAL
Inductive Proximity Sensors
LIMIT STYLE
Inductive Proximity Sensors
Introduction ........................................4
Operation ............................................5
Introduction/Operation .......................8
Selection Guide, DC styles................12
Selection Guide, AC styles ................14
Product Specifications......................16
Introduction/Operation .....................68
Selection Guide.................................71
Product Specifications......................72
CLICK FOR PDF FILE
CLICK FOR PDF FILE
BLOCK STYLE
Inductive Proximity Sensors
RING STYLE
Inductive Proximity Sensors
ACCESSORIES for
Inductive Proximity Sensors
Introduction/Operation .....................80
Selection Guide.................................82
Product Specifications......................84
Introduction/Operation .....................98
Selection Guide...............................100
Product Specifications....................102
Introduction ....................................113
Mounting Brackets .........................114
Cable Assemblies............................116
Switching Units...............................122
Motion Detectors............................128
OTHER INFORMATION
APPENDIX:
IP Codes .........................................132
NEMA requirements .......................133
Cross Reference .............................134
Glossary..........................................135
Conversion Charts ..........................137
INDEX .............................................138
TERMS & CONDITIONS .................141
WARRANTY....................................143
CLICK FOR PDF FILE
All specifications subject to change without notice or obligation
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908) 806-9400 • Fax (908) 806-9490
3
PREVIOUS
HOME
NEXT
FIND IT
Accessories
GENERAL INFORMATION
Altech accessories are available as optional equipment to
assist in the use of sensor
products.
Some sensor products require
specific accessory units in
order to perform satisfactory.
Please consult the product
specification to determine
which accessories are
essential.
The accessories include
mounting brackets, cable
assemblies, switching amplifier units, and motion detector
systems.
MOUNTING BRACKETS
Several fixtures are available
that provide the ability to
mount cylindrical and limit
style sensors.
CABLE ASSEMBLIES
Altech offers one of the largest
Quick Disconnect selection of
sensors in the industry and
matching cable assemblies.
Standard Sensors come with
2 meter fixed PVC cables, but
to improve maintenance and
mean time to repair (MTTR)
quick disconnect sensors with
matching cable assemblies
are desirable.
For DC Sensors Altech offers
a mini- style 4-pin cable
assembly, a micro style 3- and
4-pin cable assembly, and a
pico style 3-pin cable assembly. Most are available in
straight or 90° molded cable
connection, and the micro
and pico styles are also available with 2 LED’s.
For AC Sensors Altech offers
a mini- style 3-pin cable
assembly, a micro style 3-pin
and 4-pin cable assembly.
SWITCHING/AMPLIFIER
UNITS
Altech offers a wide variety of
products used in conjunction
with Ring Sensors, Analog
Sensors, Namur Sensors,
testers and power supply
modules for all sensor products.
MOTION DETECTOR
SYSTEMS
Motion detectors accept
impulses from proximity sensors when a repetitious event
is occurring. These impulses
are measured compared to a
standard. The motion detector
will “Time Out” between
impulses and provide an output for over or under the set
speed.
Altech offers completely contained motion detector systems, including built-in proximity sensors or as separate
components.
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908) 806-9400 • Fax (908) 806-9490
113
PREVIOUS
HOME
NEXT
FIND IT
Accessories
Mounting Brackets
9512-6100/9512-6200
9512-6400/9512-6600
Bracket
Metal Plate
Non-metallic mounting brackets are used for
8mm, (.31 in.), 12mm (.47 in.), 18mm (.71 in.),
and 30mm (1.18mm) cylindrical sensors.
Dimensions in mm (in.)
D=SENSOR Ø
A
B
C
E
F
Model
8 (0.31)
64 (2.52)
50 (2.0)
37 (1.46)
27 (1.06)
20 (0.79)
9512-6100
12 (0.47in.)
64 (2.52)
50 (2.0)
37 (1.46)
27 (1.06)
20 (0.79)
9512-6200
18 (0.71in.)
70 (2.76)
56 (2.20)
42 (1.65)
33 (1.3)
26 (1.02)
9512-6400
30 (1.18in.)
87 (3.43)
73 (2.87)
58 (2.28)
42 (1.65)
40 (1.57)
9512-6600
Model No. MB 1
A Metallic Mounting Bracket is available for
12mm (.47 in.) and 18mm (.071 in.)
cylindrical sensors. Bracket is finished in clear
anodized Aluminum.
Dimension in mm (in.)
13.48 (.531) Dia. Slotted Hole
41.12 (1.62)
15.87
(.625)
This bracket allows for adjustment forward,
backward, and sensor height.
Elongated Holes
5.5 x 12.89 (.218 x .50)
12.28 (.50)
31.75 (1.25) 47.63 (1.87)
11.17
(.44)
27.66 (1.09)
19.03 (.75) Dia.
Slotted Hole
All Four Corners
R6.35 (.25)
27.66
(1.09)
43.65 (1.72)
114
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908) 806-9400 • Fax (908) 806-9490
PREVIOUS
HOME
NEXT
FIND IT
Accessories
9512-8200 Mounting Plate
for Limit Style Sensors
Mounting dimensions: According to DIN 50 027/037
Material: VA 1.4301.
Dimension in mm (in.)
This mouning plate is used if the sensing device has
to be adjusted after the installation.
This mounting plate is used only for Limit Style
Sensors.
Dimension in mm (in.)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908) 806-9400 • Fax (908) 806-9490
115
PREVIOUS
HOME
NEXT
FIND IT
Accessories / Cable Assemblies
Model / Description
Dimensions
Wire Color Code
8000-5030
2m (6ft.) 3 pin
plug & cable for
AC sensors with
connector 62
Pin 1
Green
Use 8000-5035
for 5m lengths
Pin 3
White
Pin 2
Black
8000-5040
2m (6ft.) 4 pin
Cable for DC
sensors with
connector 62
Use 8000-5045
for 5m lengths
Pin 4
Green
Pin 1
Black
Pin 3
Red
Pin 2
White
Technical Data / Connectors and Receptacles: 8000-5030, 8000-5040
Application Class:
Materials:
Body:
Contact:
Insert:
Coupling Nut:
Receptacle shell:
Mechanical Data:
Protection:
Insertion Force:
Withdrawal Force:
Shock:
Vibration:
116
-40°C to +90°C
PUR, yellow
Solid-machined Brass,
Gold over Silver Plating
PUR, yellow
Standard: alumimum (black anodized)
Options: nylon (glass reinforced black);
stainless steel (passivated)
Aluminum, Clear Anodized
Options: Brass, Electroless Nickel
Plated, Stainless Steel
IP68, NEMA 6P
(only in fully locked position)
≤ 3.0N .67 lbs.
≥ 1.0N .22 lbs.
IEC 68-2-27
IEC 68-2-6
Electrical Data:
Contact Resistance:
Current Rating:
Working Voltrage:
Dialectric Withstanding
Voltage:
Insulation Resistance:
Cable:
16 AWG:
18 AWG:
Agency Approvals:
UL Recognition:
CSA Certified:
≤ 5mΩ
8000-5030 - 10A, 8000-5040 - 8A
16 AWG cable: 600 VAC-RMS
2 & 3 pole _ 2 KVAC RMS/60sec
4 & 5 pole _ 1.5 KVAC RMS/60sec
>109Ω
UL-STOW-A; Hi-Flex bare,
65 x 34 copper stranding, yellow jacket
UL-SOOW-A; AWM 2661; Hi-Flex bare
41 x 34 copper stranding, yellow jacket
E104696
LR101546-1
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908) 806-9400 • Fax (908) 806-9490
PREVIOUS
HOME
NEXT
FIND IT
Accessories / Cable Assemblies
Model / Description
Dimensions
Wire Color Code
8000-5060
2m (6ft.) right angle
4 pin plug & cable
for AC sensors with
connectors 66 & 67
Pin 3
Not Used
Pin 4
Yellow/
Green
Pin 2
Blue
Pin 1
Black
Pin 3
Not Used
Pin 4
Yellow/
Green
Pin 2
Blue
Pin 1
Black
Use 8000-5065
for 5m lengths
8000-5070
2m (6ft.) straight
4 pin plug & cable for
AC sensors with connectors 66 & 67
Use 8000-5075
for 5m lengths
Technical Data / Connectors and Receptacles: 8000-5060, 8000-5070
Application Class:
Materials:
Molded Body:
Contact:
Cable:
Coupling Nut:
Mechanical Data:
Protection:
HNE acc. to DIN 40040
-40°C to +90°C
PUR (polyurethane)
Copper alloy, gold over nickel plating
PVC, self extinguishing, orange
Brass, nickel plated
Electrical Data:
Contact Rating:
Current Rating:
Working Voltage:
Dielectric Withstanding
Voltage:
Insulation Resistance:
Cable:
22 AWG:
IP68, NEMA 6P
(only in fully locked position)
18 AWG:
Agency Approvals:
UL recognition:
CSA Certified:
≤5mΩ
3A
250V
2 KVAC RMS/60 seconds
>109Ω
Hi-Flex bare copper stranding,
yellow jacket
Hi-Flex bare copper stranding,
yellow jacket
E104696
LR101546-1
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908) 806-9400 • Fax (908) 806-9490
117
PREVIOUS
HOME
NEXT
FIND IT
Accessories / Cable Assemblies
Model / Description
Dimensions
Wire Color Code
8000-5110
2m (6ft.) straight
4 pin plug & cable
for DC sensors
(sink or source) with
connectors 45,50,63 & 65
Pin 2
Not Used
Pin 1
Brown
Use 8000-5115
for 5m lengths
8000-5120 & 8000-5280
Pin 2
Not Used
2m (6ft.) right angle
4 pin plug & cable
for DC sensors
(sink or source) with
connectors 45.50,63 & 65
8000-5120
Pin 1
Brown
8000-5120 – Use 8000-5125
for 5m lengths
Pin 2
White
8000-5280
8000-5280 – Use 8000-5285
for 5m lengths
Pin 1
Brown
Pin 3
Blue
Pin 4
Black
Pin 3
Blue
Pin 4
Black
Pin 3
Blue
Pin 4
Black
Technical Data / Connectors and Receptacles: 8000-5110, 8000-5120, 8000-5280
Application Class:
Materials:
Molded Body:
Contact:
Cable
Coupling Nut:
Mechanical Data:
Protection:
118
HNE acc. to DIN 40040
-40°C to +90°C
PUR (Polyurethane)
Copper alloy, gold over
nickel plating
PVC, self extinguishing, yellow
Brass, nickel plated
IP68, NEMA 6P
(only in fully locked position)
Electrical Data:
Contact Resistance:
Current Rating:
Working Voltage:
Dielectric Withstanding
Voltage:
Insulation Resistance:
Cable:
22 AWG:
Agency Approvals:
UL Recognition:
CSA Certified:
≤ 5mΩ
3A
250V
2 KVAC RMS/60 secinds
>109Ω
AWM 2661; Hi-Flex bare,
26 x 36 or 22 x 36 copper stranding,
yellow jacket
E104696
LR101546-1
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908) 806-9400 • Fax (908) 806-9490
PREVIOUS
HOME
NEXT
FIND IT
Accessories / Cable Assemblies
Model / Description
Dimensions
Wire Color Code
8000-5130
2m (6ft.) straight
3 pin plug & cable
for AC sensors with
connector 48,68
Pin 3
Red/Wht
Use 8000-5135
for 5m lengths
Pin 2
Red/Blk
Pin 1
Green
8000-5140
Pin 3
Red/Wht
2m (6ft.) right angle
3 pin plug & cable
for AC sensors with
conector 48,68
Pin 1
Green
Pin 2
Red/Blk
Use 8000-5145
for 5m lengths
Technical Data / Connectors and Receptacles: 8000-5130, 8000-5140
Application Class:
Materials:
Molded Body:
Contact:
Receptacle:
Cable:
Coupling Nut:
Mechanical Data:
Protection:
HNE acc. to DIN 40040
-40°C to +90°C
PUR (Polyurethane)
Copper alloy, gold over nickel
plating
Brass, nickel plated
PVC, self-extinguishing, yellow
Brass, nickel plated
IP68, NEMA 6P
(only in fully locked position)
Electrical Data:
Contact Resistance:
Current Rating:
Working Voltage:
Dielectric Withstanding
Voltage:
Insulation Resistance:
Cable:
22 AWG:
Agency Approvals:
UL Recognition:
CSA Certified:
≤ 5Ω
3A
250V
2 KVAC RSM/60 seconds
>109Ω
AWM 2661; Hi-Flex bare, 26 x 36
copper stranding, yellow jacket
E104696
LR101546-1
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908) 806-9400 • Fax (908) 806-9490
119
PREVIOUS
HOME
NEXT
FIND IT
Accessories / Cable Assemblies
Model / Description
Dimensions
Wire Color Code
8000-5150 & 8000-5160
2m (6ft.) 4 pin plug & cable with 2
LED's for DC sensors with connectors
45,50,63 & 65. RP-515 for sink (NPN)
output sensor. RP-516 for source
(PNP) output sensor.
Pin 2
Not used
Pin 3
Blue
Pin 1
Brown
Pin 4
Black
Use 8000-5155 & 8000-5165
for 5mm lengths
9512-0200
2m (6ft.) straight 4 pin metal plug & cable for connector 59
Pin 3
Red
Pin 4
Blue
Pin 2
White
Pin 1
Black
Technical Data / Connectors and Receptacles: 8000-5150, 8000-5160
Application Class:
Materials:
Molded Body:
Contact:
Insert:
Cable:
Coupling Nut:
Mechanical Data:
Protection:
Insertion Force (Contact):
Shock:
Vibration:
120
-40°C to +90°C
PUR (Polyurethane)
Copper Alloy, gold over nickel
plating
PUR (Plugs)
PVC, self-extinguishing, yellow
Brass, nickel plated
IP68, NEMA 6P
(only in fully locked position)
≤ 2N .45 lbs.
≥ .5N .11 lbs.
IEC 68-2-27
IEC 68-2-6
Electrical Data:
Contact Resistance:
Current Rating:
Working Voltage:
Dielectric Withstanding
Voltage:
Insulation Resistance:
Cable:
Agency Approvals:
UL Recognition:
CSA Certified:
≤ 5mΩ
3A
10-30 VDC
2 KVAC RMS/60 seconds
>109Ω
.25mm2
E104696
LR101546-1
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908) 806-9400 • Fax (908) 806-9490
PREVIOUS
HOME
NEXT
FIND IT
Accessories / Cable Assemblies
Model / Description
Dimensions
Wire Color Code
8000-5220
Pin 3
Blue
2m (6ft.) straight
3 pin plug & cable for DC sensors
with 64 connector
Pin 1
Brown
Use 8000-5225 for 5m lengths
Pin 2/4
Black
8000-5230
2m (6ft.) right angle 3 pin plug &
cable with 2 LED's for DC, PNP
(source) sensors with 64 connector
Pin 3
Blue
Use 8000-5235 for 5m lengths
Pin 1
Brown
Pin 2/4
Black
8000-5240
2m (6ft.) right angle 3 pin plug & cable
with 2 LED's for DC, NPN
(sink) sensors with 64 connector
Use 8000-5245 for 5m lengths
Technical Data / Connectors and Receptacles: 8000-5220, 8000-5230, 8000-5240
Application Class:
Materials:
Molded Body:
Contact:
Receptacle:
O-Ring for Receptacle:
Cable:
Coupling Nut:
Mechanical Data:
Protection:
HNE acc. to DIN 40040
-25°C to +90°C ≤75%rF
TPU, self-extinguishing (RMS only –
PA 6.6, self extinguishing)
Solid machined brass, gold
over nickel plating
Brass, nickel plated
Viton
PVC, self extinguishing, orange
Brass, nickel plated
Electrical Data:
Contact Resistance:
Current Rating:
Working Voltage:
Dielectric Withstanding
Voltage:
Insulation Resistance:
≤ 5mΩ
4A
60 VAC / RMS/75VDC (solder
contacts potted with epoxy for
receptacles)
250V
2 K VAC RMS/60 seconds
>109Ω
Snap-In – IP65, NEMA 4
Locking – IP 68 NEMA 6P
(only in fully locked position)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908) 806-9400 • Fax (908) 806-9490
121
PREVIOUS
Accessories
8300-0100/0500
Power and Switching Units
for NPN and PNP sensors
The Universal Power and Switching Unit
is used to supply power for sensors and
provide a relay output of the sensor
status.
The unit is DIN rail mountable and can
supply power for one NPN or PNP sensor.
HOME
NEXT
FIND IT
• Short circuit protection
• Temperature range:
-10 to 50°C (14 - 122°F)
• Type 8300-0100: 230V
• Type 8300-0500: 110V
• LED for Output Energized
Standard Data
Cat. No.
8300-0100
8300/0500
Supply Voltage:
230V AC
110V AC
Operating Frequency:
50/60Hz
50/60Hz
Temperature Range:
-10°C up to +50°C
-10°C up to +50°C
Output Voltage:
(for sensor supply)
24V, stabilized and
short circuit-proof
24V, stabilized and
short circuit-proof
Max. Load Current:
120mA
120mA
Relay Output:
SPDT
SPDT
Max. Switching Voltage:
250V AC
250V AC
Max. Switching Current:
5A (ohmic load)
5A (ohmic load)
Max. Switching Capacity:
1100VA
1100VA
Dimensions in mm (in.)
122
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908) 806-9400 • Fax (908) 806-9490
PREVIOUS
Accessories
8100-2200
Power and Switching Units
for Namur sensors
Namur sensors operate with a supply
voltage of 8.2V. Therefore, Namur sensors
are mostly operated with switching units
(with a current interface according to DIN
19234). The 8100-2200 Namur Switching
Unit is equipped with such an interface.
The Namur sensor has a low impedance
with no metal target detected. When a
metal target is detected the impedance is
higher. This change in impedance causes
current change which is detected by the
switching unit.
The 8100-2200 switching unit opens up
application areas such as standard
proximity switches to Namur sensors. This
is supported by the small overall dimensions of the Namur sensors.
HOME
NEXT
FIND IT
• Power supply unit
• Temperature range:
-10 to 70°C (14 - 158°F)
• Amplifier
• Relay Output
• Drives one Namur sensor
Standard Data
Cat. No.
Supply Voltage:
8100-2200
220V/110V AC
Operating Frequency:
50/60Hz
Temperature Range:
-10°C up to +70°C (14 to 158°F)
Output Voltage:
(for sensor supply)
Relay Output:
8.2V
SPDT
Switching Voltage:
250V AC
Switching Current:
5A (resistive)
Max. Switching Capacity:
1100VA
Dimensions in mm (in.)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908) 806-9400 • Fax (908) 806-9490
123
PREVIOUS
Accessories
8102-0900/0930
Power and Switching Units
for High Sensitive Ring
Sensors
This switching amplifier is used with
ALTECH Dynamic Ring Sensors. It can
also be used as a time delay for NPN sensors since it contains a delay function.
Both a transistor output and relay contact
output are available.
HOME
NEXT
FIND IT
• Adjustable Pulse Duration of
the output signal
• Short circuit protection
• Transistor Output and a
relay output
• LED for Output Energized
• Type 8102-0900: 220V
• Type 8100-0930: 110V
• Temperature range:
-10 to 50°C (14 - 122°F)
• Adjustable Output timing
delay of 10 msec to 18 seconds
Standard Data
Cat. No.
8102-0930
8102-0900
Supply Voltage:
220V AC
110V AC
Operating Frequency:
50/60Hz
50/60Hz
Temperature Range:
-10°C up to +50°C
-10°C up to +50°C
Output Voltage:
(for sensor supply)
24V, stabilized and
short circuit-proof
24V, stabilized and
short circuit-proof
Max. Load Current
80mA
80mA
Voltage Drop
0.5V
0.5V
≤10µA
≤10µA
SPDT
SPDT
Transistor Output:
Leakage Current
Relay Output:
Max. Switching Voltage:
250V AC
250V AC
Max. Switching Current:
5A (ohmic load)
5A (ohmic load)
Max. Switching Capacity:
1100VA
1100VA
Dimensions in mm (in.)
124
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908) 806-9400 • Fax (908) 806-9490
PREVIOUS
Accessories
8100-2100/2130
Power and Switching Units
for Analog Sensors
The multi-function amplifier Type 81002100/2130 operates in conjunction with either
one of the analog sensors 9914-0800, 94140800, 9414-0900, 9914-1000, 9814-1133,
9814-2133, 9714-2000 or 9714-4300. It contains a power supply for the sensor voltage
(24V DC) and converts the analog signal of the
sensors to four different outputs.
1. Analog voltage output:
0-10V DC, max 5mA.
2. Analog current output:
0-20mA, max. load resistance 500Ω.
3. Digital Output:
four bit, open collector, npn, "active
low".
4. Relay Output:
3 relays for triggering point are built in
(change over contact, SPDT).
Load voltage: 220V AC
Load current: 5A (resistive)
Switching capacity:1100VA
The switching point of each relay can
be adjusted by a potentiometer and is
indicated by individual LED's.
Settings:
Three Relays with switching thresh
olds can be chosen by means of
three integrated potentiometers.
When reaching the switching threshold, the corresponding LED will light
up.
In addition to Units 8100-2100 and 8100-2130,
there are two Analog Modules available to be
mounted onto DIN/EN mounting rails.
• Module 8100-2400 with:
-Analog voltage output
-Analog current output
-4-bit digital output
• Module 8100-2500 with:
-8-bit digital output
Modules 8100-2400 and 8100-2500 are
described on page 126.
HOME
NEXT
FIND IT
• Provides 24V DC for Sensors
• Choice of 4 Outputs
– Analog Voltage
– Analog Current
– 4 Bit Digital
– Relays (3) with LED indicators
• Compatable wih all Altech Analog
Sensors
Standard Data
Cat. No.
8100-2100
8100/2130
Supply Voltage:
220V AC
110V AC
Operating Frequency:
50/60Hz
50/60Hz
Temperature Range:
-10°C up to +60°C (32 - 140°F)
-10°C up to +60°C (32 - 140°F)
24V
24V
Supply Voltage for
Analog Sensor
Dimensions in mm (in.)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908) 806-9400 • Fax (908) 806-9490
125
PREVIOUS
Accessories
8100-2400/8100-2500
Analog Input Multi-Function
Switching Unit
The Multifunction Amplifiers Type 81002400 and 8100-2500 operate in conjunction with either one of the Analog sensors
9914-0800, 9914-1000, 9914-1133, 98142133, 9714-2000 or 9714-4300. It operates with customer supplied DC voltage,
18-30V DC, and converts the analog signal
to three (3) different outputs for the 81002400. The 8100-2500 has one output, an 8
bit digital output.
The 8100-2500, 8-bit digital output divides
the analog voltage into 256 individual
increments which results in a resolution of
10µm/bit (.0004 in./bit). All outputs are protected against short circuits, and the unit is
protected from Polarity reversal.
HOME
NEXT
FIND IT
• 8100-2400 has choice of 3 outputs
– Analog Voltage
– Analog Current
– 4 Bit Digital
• 8100-2500 has an 8 bit digital output
• Output protected against short
circuits and polarity reversal
Standard Data
Cat. No.
8100-2400
8100-2500
Supply Voltage:
18-30V DC
18-30V DC
Temperature Range:
0 to 60°C (32 to140°F)
0 to 60°C (32 to140°F)
Analog Voltage Output:
0 to 10V
–
Analog Current Output:
0 to 20mA or
4 to 20mA (jumper)
–
4 bit open collector, PNP
8 bit open collector, PNP
Digital Output 1:
Max. load current:
Voltage drop:
Max. Switching Voltage:
Digital Output 2:
20mA
20mA
≤3.5V at 20mA
≤3.5V at 20mA
30V
30V
–
8 bit TTL output
VQH
–
≤4.5V
IQH
–
≤2mAV
VQL
–
≤0.3V
IQL
–
≤6mA
8100-2400
8100-2500
126
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908) 806-9400 • Fax (908) 806-9490
PREVIOUS
Accessories
8309-0130/8309-0230
Testers for DC and
AC Sensors
HOME
NEXT
FIND IT
• Tests an inductive sensors
field in place, without
removing the sensor
• Tests the output circuit
• Identifies the sensor output
as either sink (NPN) or
source (PNP) for DC sensors
These testers can greatly reduce downtime and maintenance costs by quickly
checking the proper function of all kinds
of inductive capacitive, or photelectric
sensors.
8309-0130
For DC Sensors
8309-0230
For AC Sensors
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908) 806-9400 • Fax (908) 806-9490
127
PREVIOUS
Accessories
9863-4300/4400/4600
Motion Detector Systems
These Motion Detecting Systems in Limit
Style housing are used to control the rotational speed of motors, pumps, and conveyor drives. They are completely self-contained, with an integral proximity switch
and timing functions to perform over and
under speed detection.Typical targets are
cam lobes, sprocket teeth, or small tabs.
HOME
NEXT
FIND IT
• 9 position sensor head adjustment
simplifies adaptation to conditions
• Programmable NO/NC outputs
• Speed range of 100 - 3000 pulses per minute
• Startup delay 0.5 - 6.0 seconds, adjustable
• 2 LED's for Output Energized & Operating Voltage
• IP67 Protection (NEMA 1,3,4,6,12,13) Protection
Standard Data
Cat. No.
Mounting:
Sensing Distance:
Switching Mode:
9863-4300
9863-4400
Flush
Semi-Flush
9863-4600
Flush
15mm (0.59 in.)
25mm (0.98 in.)
15mm (0.59 in.)
PNP
PNP
PNP
Type Sensor:
Overspeed
Overspeed
Underspeed
Speed Range:
100 - 3000 ppm
100 - 3000 ppm
100 - 3000 ppm
Startup Delay:
0.5 -6 sec
0.5 -6 sec
0.5 -6 sec
Voltage Range:
10 - 30V DC
10 - 30V DC
10 - 30V DC
Ripple Voltage:
≤10%
≤10%
≤10%
Voltage Drop Across Sensor:
≤2.4V
≤2.4V
≤2.4V
Max. Load Current:
400mA
400mA
400mA
Supply Current:
≤34mA
≤34mA
≤34mA
Leakage Current:
≤10µA
≤10µA
≤10µA
Repeat Accuracy:
.75mm (0.3 in.)
1.25mm (.049 in.)
.75mm (.03 in.)
-25 to +70°C
-25 to +70°C
-25 to +70°C
Trogamid T
Trogamid T
Trogamid T
Temperature Range:
Housing Material:
Output, all models: If speed is above limit, the output is switched on.
If speed is below limit, the output is switched off.
Dimensions in mm (in.)
128
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908) 806-9400 • Fax (908) 806-9490
PREVIOUS
HOME
NEXT
Accessories
• Operates on DC supply
voltage
8303-0430
Motion Detector in
Universal Housing
• 3 Speed Ranges
This motion detector detects the rotational
speed of actuation, rotating shafts or other
movements such as lifting or pushing.The
impulse can be given by any PNP or NPN
DC-sensor. The impulse is effected by
control cams, gears, wheels or other
signals. The housing can be mounted on a
DIN/EN rail or on a mounting plate.
FIND IT
• System start-up delay
adjustable
Standard Data
Cat. No.
8303-0430
Supply Voltage:
18V - 30V
Temperature Range:
-10°C up to +60°C
5 speed range:
6 - 60 rpm
60 -600 rpm
600 - 6000 rpm
Start-up Delay:
0.5 - 10 sec
Hysterisis
0.5 - 10% adjustable
Relay Output:
Function Switch:
SPDT 250V/5A
Position S — Relay activated for overspeed
Positiion 0 — Relay activated for underspeed
LED - Switching state indication: Same time as relay contact
Dimensions in mm (in.)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908) 806-9400 • Fax (908) 806-9490
129
PREVIOUS
HOME
NEXT
FIND IT
Accessories
8100-2700/2800
Motion Detector in
Universal Snap-on Housing
These units monitor/control electronically
the speed of drives, rotating shafts or other
motions. Both inductive and other threewire DC voltage proximity switches can be
used as pulse generator input to this
motion detector. Pulse generation is effected e.g. by rotating control cams, gearwheels or other signal targets.
The housing can be snapped on to DIN/EN
mounting rails or threaded to mounting
plates.
• System start-up delay adjustment
• 3 Speed ranges with adjustment to set speed
• DC Supply Voltage
• Relay Output
Standard Data
Cat. No.
Supply voltage (polarity reversal)
8100-2700
8100-2800
18V - 30V DC
18V - 30V DC
≤50mA at 24V
–
NPN or PNP sensor signal
NPN or PNP sensor signal
Analog Output Voltage:
–
1V - 10V
load resistance min 2KΩ
Analog Current Output:
–
Supply Current:
Inputs:
adjustable 4-20mA
load resistance 0-500Ω
Relay Output:
Current Carrying Capacity:
Normally Open/Closed
Selectable via Plug::
Speed Ranges:
Starting Delay Adjustable:
Hysterisis Adjustable:
LED Switching State Indication:
Temperature Range:
130
250V/5A
250V/5A
In NO position, the relay will
be activiated, if the set
speed is exceeded.
In NC position, the relay will
be activated if the speed
falls below the set
In NO position the relay will
be activated, if the set
speed is exceeded
6 - 60 rpm
60 - 600 rpm
600 - 6000 rpm
10 - 100 rpm
100 - 1000 rpm
1000 - 10000 rpm
0.5 - 10 sec.
1 - 10 sec
5 - 10%
1 - 10%
activated same
time as relay
activated same
time as relay
-0°C to +60°C (32-140°F)
-0°C to +60°C (32-140°F)
Altech Corp ® • 35 Royal Road • Flemington NJ 08822-6000 • Phone (908) 806-9400 • Fax (908) 806-9490
PREVIOUS
HOME
NEXT
FIND IT
THE NEWEST ADDITION TO ALTECH'S
SENSOR PRODUCTS...
Pulsotronic Capacitive, Photo-electric,
and Ultrasonic Sensors.
ALTECH now offers a comprehensive line of Capacitive,
Photo-electric. and Ultrasonic Sensors to satisfy the
expanding Automation Industry.
These new Sensors are available in DC (PNP & NPN),
and AC models. Housing styles are Cylindrical,
Limit Style, and Block.
Features:
• Capacitive – Detects Metals, Non-Metals, and Liquids.
• Photo-electric – Available in Diffuse Reflection,
Retro-Reflection, and Through Beam models.
• Ultrasonic – Digital and Analog models available,
using sound to detect targets and target distances.
...Contact Altech for more information
Altech Corp ® • 35 Royal Road • Flemington NJ 08822-6000 • Phone (908) 806-9400 • Fax (908) 806-9490
131