SmartRelayOutside.pdf 1 9/24/12 1:35 PM Altech Universal Digital Multi-Timer Altech’s AMT-Series of Universal Digital Multi-Timers comprises 4 models featuring 8 or 18 timer functions to offer highest flexibility in controlling operations. The time range is adjustable from 0.1s to 999h. An LCD display shows current Run time information. Features Multifunctional Timer (8 or 18 Functions) Universal Voltage 24~265 VAC/ DC Wide Time Range: 0.1s ~ 999h 3 Digit LCD Display for Preset Time and Run Time DIN Rail Mounted 17.5mm Width LISTED Digital Timers Cat. No. Output Contacts No. of Timer Functions E351145 AMT8-S1 1 C/O 8 AMT8-D2 2 NO 8 AMT12-S1 1 C/O 18 1) ON Delay [A] 2) Cyclic OFF/ ON [b] 3) Cyclic ON/ OFF [C] 4) Signal ON/ OFF [d] 5) Signal OFF Delay [E] 6) Interval [F] 7) Signal OFF/ ON [G] 8) One Shot Output [H] Functions / [setting mode] 1) ON Delay [0] 2) Cyclic OFF/ ON [1] 3) Cyclic ON/ OFF [2] 4) Impulse on Energizing [3] 5) Accumulative Delay on Signal [4] 6) Accumulative Delay on Inverted Signal [5] 7) Accumulative Impulse on Signal [6] 8) Signal ON Delay [7] 9) Inverted Signal ON Delay [8] 10) Signal OFF Delay [9] 11) Impulse ON/ OFF [A] 12) Signal OFF/ ON [b] 13) Leading Edge Impulse 1 [C] 14) Leading Edge Impulse 2 [d] 15) Trailing Edge Impulse 1 [E] 16) Trailing Edge Impulse 2 [F] 17) Delayed Impulse [G] 18) Inverted Signal ON Delay 2 [H] C M Y CM MY Supply Voltage Power Consumption Timing Range Reset Time Repeat Accuracy Output Contact Rating Electrical Life Mechanical Life AC-15 Rating DC-13 Rating Operating Temperature Storage Temperature Weight Protection Enclosure Protection Terminals Torque Terminal Wire Size 24 - 265 VAC/ DC (50, 60Hz) 10 VA max. 0.1s ~ 999h 200ms max. +-0.5% 8A @ 240 VAC/ 24 VDC (resistive) 10,000 switching cycles 2,000,000 switching cycles Rated Voltage (Ue): 125/ 240V, Rated Current (Ie): 3/1.5A Rated Voltage (Ue): 125/ 250V, Rated Current (Ie): 2/0.22/0.1A -10ºC ~ +55ºC (+14ºF ~ 131ºF) -20ºC ~ +65ºC (-4ºF ~ 149ºF) 85g (0.14lb.) IP30 IP20 0.40 Nm (3.5 lb.in.) 0.3-2.5 mm2 (22-14 AWG) Connection Diagrams Dimensions A1 A1 B1 B1 A2 A2 AMT8-S1, AMT12-S1 67 mm 45 mm K Specifications 100 mm CY CMY AMT12-D2 2 NO 18 Run Time Setting Mode HMS SET ADJ Preset Time Up Down LED Indication for Relay Status Scan this QR code for more information. 76.0 mm 89 mm • • • • • • AMT8-S2, AMT12-S2 17.5 mm Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com Altech Corporation 35 Royal Road Flemington, NJ 08822-6000 P 908.806.9400 • F 908.806.9490 www.altechcorp.com Altech Corp.® 120-3000 Printed October 2012 SmartRelayInsideIeps.pdf 1 9/24/12 1:03 PM Altech Smart Relay Altech Smart Relay Connection Diagrams Technical Specifications I/O Extensions (Max.) Utilization Category AC-15 Smart Relay DC-13 Power Reserve (For Clock Only) Operating Temperature Storage Temperature Humidity (Non Condensing) Enclosure Mounting Degree of Protection LISTED E352868 Standards and Certifications • UL 508 • IEC 61000-3-2 • IEC 61000-4-2-1~11 Supply Voltage (-20% to + 10%) Power Consumption Max. Supply current Digital Inputs Digital Input Range Analog Inputs Analog Input Range Digital Relay Output Weight • 250 lines of ladder programming • 16 soft text messages, Time Switches, Compare Counters, Timers, Counters & 12 analog functions CY Function Blocks Timers: Counters: Time Switches: Compare Counters: Analog Functions: Soft Text Messages: Auxiliary Relays: 16 16 16 16 12 16 32 (ON Delay, Interval, Cyclic ON-OFF, OFF Delay) (Up/Down, Retentive selectable) (Weekly / Daily) AltechCorp.com/SmartRelay Mounting Dimensions 1 2 INPUT 3 4 12 - 24 V DC 5 6 V1 V2 + C1 C2 PROGRAM RUN PARAMETERS UTILITIES 1 2 INPUT 3 4 12 - 24 V DC INPUT 6 X DC V1, V2 = 0 -10 V DC 90.5mm (3-9/16”) + 1 2 3 5 4 5 6 7 Base Module 3 8 B 4 SEL C Q2 Q3 Q4 4.3mm (11/64”) Programmable Smart Relay Base Module ASR-B24DC 110-240 VAC (50/60Hz) 5W 36 mA 8 (0-40VAC) OFF,(80-265VAC) ON N/A N/A 4 NO (8A@240V AC, 5A@30V DC) 0.51 lb. (230 g) 12-24 VDC 5W 360 mA 6 (0-4VDC) OFF,(8-26.4VDC) ON 2 (can be used as Digital Inputs) 0 to 10 VDC 4 NO (8A@240V AC, 5A@30V DC) 0.51 lb. (230 g) OP1 OP2 OP3 TTL Level RS-485 protocol (two wires, D+, D-) 32 standard unit loads 2000 Vrms 300, 600, 1200, 2400, 4800, 9600 -10°C to +55°C -20°C to +70°C Red LED’s for Tx & Rx. Green LED for Power indication 0.19 lb. (84 g) INPUT 8XAC Z1 OK I1 I2 I3 I4 I5 I6 ANAN C1 C2 INPUT 6XDC An1, An2 = 0-10 V DC 12 - 24V DC DEL Z4 ALT PROGRAM RUN PARAMETER UTILITIES Z3 Z2 INPUT 6XDC V1,V2=0-10 VDC 12 - 24V DC DEL Z4 ALT + - I1 I2 I3 I4 I5 I6 V1 V2 C1 C2 Z1 Z3 ESC Z2 OK Q2 Q1 LOAD LOAD ASR-E24DC 6 (0-4VDC) OFF,(8-26.4VDC) ON 2 (can be used as Digital Inputs) 0 to 10 VDC 4 NO (8A@240V AC, 5A@30V DC) 0.5 lb. (225 g) OUTPUT 4 X RELAY / 8A Q1 Q4 Q3 LOAD LOAD Q2 LOAD FUSE LOAD Q3 LOAD Q4 LOAD +SUPPLY - SUPPLY AC Base Module OUTPUT 4 X RELAY / 8A Q1 FUSE LOAD Q2 Q3 LOAD FUSE LOAD OP2 LOAD OP3 OP4 LOAD DC Base Module DC Expansion Module I1 I2 I3 I4 I5 I6 I7 I8 C1 C2 110 - 230 V AC 50 / 60 Hz INPUT 8XAC DEL Z4 ALT PROGRAM RUN PARAMETER UTILITIES Z1 Z3 ESC Z2 OK 485DC OUTPUT 4 X RELAY / 8A ALTECH SAMRT RELAY OUTPUT 4 X RELAY / 8A ASR-SOFT Q1 Q2 Q3 Q4 Q1 Q2 Q3 Fig. 3 Connection Between Base Module & Expansion Q4 Fig. 4 Connection Between Base Module & Communication Module Same for both AC & DC Power Supply Wiring 1. Although the Altech Smart Relay has been designed to withstand the negative effects of any electrical noise that might be present its power supply. It may be necessary to insert an isolation transformer between the supply and line terminals of the Altech Smart Relay. 2. While using the DC Altech Smart Relay, run the 24 VDC Input line separate from 100 ~240V AC power lines. Communication Cable Cat. No. Supply Voltage Weight Rx Tx PORT TTL PORT-RS485 ASR-C485-120AC 110-240 VAC 0.18 lb. (80 g) Wiring of Input/Ouput 1. Separate input and output lines. 2. When the output lines are running close to power supply or input lines, use shielded wires and ground them. ASR-C485-24DC 12-24 VDC 0.19 lb. (84 g) Accessories D+ D- OP4 4.3mm (11/64”) Programmable Smart Relay Expansion Module Programmable Smart Relay Communication Module Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com Cat. No. Weight ASR-MC Memory Card 0.18 lb. (80 g) ASR-USB USB Cable 0.22 lb. (100 g) ASR-RS232 Serial RS232 Cable 0.24 lb. (110 g) Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com LOAD +SUPPLY Fig. 2 L N INPUT 8XAC OP1 LOAD SUPPLY AC Expansion Module I1 I2 I3 I4 I5 I6 I7 I8 C1 C2 Q4 LOAD Fig. 1 L N OUTPUT 4 X RELAY / 8A 12-24 V DC OUTPUT 4 X RELAY / 8A OUTPUT 4 X RELAY / 8A Q1 ASR-B120AC ASR-E120AC 8 (0-40VAC) OFF,(80-265VAC) ON N/A N/A 4 NO (8A@240V AC, 5A@30V DC) 0.5 lb. (225 g) + - I1 I2 I3 I4 I5 I6 I7 I8 C1 C2 110 - 230 V AC 50 / 60 Hz ESC FUSE +SUPPLY - Expansion Module 110 - 230 V AC 50 / 60 Hz Cat. No. Digital Inputs Digital Input Range Analog Inputs Analog Input Range Digital Relay Output Weight Input Output Number of Nodes Isolation Voltage Baud Rate Operating temperature Storage temperature LED Indicators Weight FUSE +SUPPLY L N INPUT 8XAC PROGRAM RUN PARAMETER UTILITIES + C1 C2 A O/P 2 AN AN 1 2 INPUT 6 X DC AN1, AN2 = 0 -10 V DC I/P 1 6 36mm (1-27/64”) 52.3mm (2-1/16”) 72mm (2-53/64”) 45mm (1-49/64”) 72mm (2-53/64”) 90mm (3-35/64”) 64.9mm (2-35/64”) N FUSE SUPPLY I1 I2 I3 I4 I5 I6 I7 I8 C1 C2 110 - 230 V AC 50 / 60 Hz RS485 Communication Module (including communication cable) (DC Model) (Priority Driven) 100mm (3-15/16”) K FREE SOFTWARE DOWNLOAD 45mm (1-49/64”) CMY L L N Expansion Module Programming Features 90.5mm (3-9/16”) MY N FUSE SUPPLY FUSE 100mm (3-15/16”) CM L OUTPUT 4 X RELAY / 8A Cat. No. • Supports upto 48 I/Os (32 digital inputs & 16 digital outputs) • DST Feature Available • Backlit LCD Screen for display & modification of pre-selected parameters of functional blocks, viewing I/O status and programming on the device • PC software for programming, online & offline simulation, documentation & printing • Designed for use in automation for commercial & Industrial sectors • Modbus Communication M Y SUPPLY, INPUT & OUTPUT CONNECTIONS Base Module Features C 3 Rated Voltage (Ue): 120/240 V, Rated Current (Ie): 3.0/1.5 A Rated Voltage (Ue): 24/125/250 V, Current (Ie): 2.0/0.22/0.1 A 150h at -10°C to +55°C -10°C to +55°C -25°C to +70°C 95% (Rh) Flame Retardant UL 94-V0 Base / DIN Rail IP 20 for Terminals, IP 40 for Enclosure Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com SmartRelayInsideIeps.pdf 1 9/24/12 1:03 PM Altech Smart Relay Altech Smart Relay Connection Diagrams Technical Specifications I/O Extensions (Max.) Utilization Category AC-15 Smart Relay DC-13 Power Reserve (For Clock Only) Operating Temperature Storage Temperature Humidity (Non Condensing) Enclosure Mounting Degree of Protection LISTED E352868 Standards and Certifications • UL 508 • IEC 61000-3-2 • IEC 61000-4-2-1~11 Supply Voltage (-20% to + 10%) Power Consumption Max. Supply current Digital Inputs Digital Input Range Analog Inputs Analog Input Range Digital Relay Output Weight • 250 lines of ladder programming • 16 soft text messages, Time Switches, Compare Counters, Timers, Counters & 12 analog functions CY Function Blocks Timers: Counters: Time Switches: Compare Counters: Analog Functions: Soft Text Messages: Auxiliary Relays: 16 16 16 16 12 16 32 (ON Delay, Interval, Cyclic ON-OFF, OFF Delay) (Up/Down, Retentive selectable) (Weekly / Daily) AltechCorp.com/SmartRelay Mounting Dimensions 1 2 INPUT 3 4 12 - 24 V DC 5 6 V1 V2 + C1 C2 PROGRAM RUN PARAMETERS UTILITIES 1 2 INPUT 3 4 12 - 24 V DC INPUT 6 X DC V1, V2 = 0 -10 V DC 90.5mm (3-9/16”) + 1 2 3 5 4 5 6 7 Base Module 3 8 B 4 SEL C Q2 Q3 Q4 4.3mm (11/64”) Programmable Smart Relay Base Module ASR-B24DC 110-240 VAC (50/60Hz) 5W 36 mA 8 (0-40VAC) OFF,(80-265VAC) ON N/A N/A 4 NO (8A@240V AC, 5A@30V DC) 0.51 lb. (230 g) 12-24 VDC 5W 360 mA 6 (0-4VDC) OFF,(8-26.4VDC) ON 2 (can be used as Digital Inputs) 0 to 10 VDC 4 NO (8A@240V AC, 5A@30V DC) 0.51 lb. (230 g) OP1 OP2 OP3 TTL Level RS-485 protocol (two wires, D+, D-) 32 standard unit loads 2000 Vrms 300, 600, 1200, 2400, 4800, 9600 -10°C to +55°C -20°C to +70°C Red LED’s for Tx & Rx. Green LED for Power indication 0.19 lb. (84 g) INPUT 8XAC Z1 OK I1 I2 I3 I4 I5 I6 ANAN C1 C2 INPUT 6XDC An1, An2 = 0-10 V DC 12 - 24V DC DEL Z4 ALT PROGRAM RUN PARAMETER UTILITIES Z3 Z2 INPUT 6XDC V1,V2=0-10 VDC 12 - 24V DC DEL Z4 ALT + - I1 I2 I3 I4 I5 I6 V1 V2 C1 C2 Z1 Z3 ESC Z2 OK Q2 Q1 LOAD LOAD ASR-E24DC 6 (0-4VDC) OFF,(8-26.4VDC) ON 2 (can be used as Digital Inputs) 0 to 10 VDC 4 NO (8A@240V AC, 5A@30V DC) 0.5 lb. (225 g) OUTPUT 4 X RELAY / 8A Q1 Q4 Q3 LOAD LOAD Q2 LOAD FUSE LOAD Q3 LOAD Q4 LOAD +SUPPLY - SUPPLY AC Base Module OUTPUT 4 X RELAY / 8A Q1 FUSE LOAD Q2 Q3 LOAD FUSE LOAD OP2 LOAD OP3 OP4 LOAD DC Base Module DC Expansion Module I1 I2 I3 I4 I5 I6 I7 I8 C1 C2 110 - 230 V AC 50 / 60 Hz INPUT 8XAC DEL Z4 ALT PROGRAM RUN PARAMETER UTILITIES Z1 Z3 ESC Z2 OK 485DC OUTPUT 4 X RELAY / 8A ALTECH SAMRT RELAY OUTPUT 4 X RELAY / 8A ASR-SOFT Q1 Q2 Q3 Q4 Q1 Q2 Q3 Fig. 3 Connection Between Base Module & Expansion Q4 Fig. 4 Connection Between Base Module & Communication Module Same for both AC & DC Power Supply Wiring 1. Although the Altech Smart Relay has been designed to withstand the negative effects of any electrical noise that might be present its power supply. It may be necessary to insert an isolation transformer between the supply and line terminals of the Altech Smart Relay. 2. While using the DC Altech Smart Relay, run the 24 VDC Input line separate from 100 ~240V AC power lines. Communication Cable Cat. No. Supply Voltage Weight Rx Tx PORT TTL PORT-RS485 ASR-C485-120AC 110-240 VAC 0.18 lb. (80 g) Wiring of Input/Ouput 1. Separate input and output lines. 2. When the output lines are running close to power supply or input lines, use shielded wires and ground them. ASR-C485-24DC 12-24 VDC 0.19 lb. (84 g) Accessories D+ D- OP4 4.3mm (11/64”) Programmable Smart Relay Expansion Module Programmable Smart Relay Communication Module Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com Cat. No. Weight ASR-MC Memory Card 0.18 lb. (80 g) ASR-USB USB Cable 0.22 lb. (100 g) ASR-RS232 Serial RS232 Cable 0.24 lb. (110 g) Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com LOAD +SUPPLY Fig. 2 L N INPUT 8XAC OP1 LOAD SUPPLY AC Expansion Module I1 I2 I3 I4 I5 I6 I7 I8 C1 C2 Q4 LOAD Fig. 1 L N OUTPUT 4 X RELAY / 8A 12-24 V DC OUTPUT 4 X RELAY / 8A OUTPUT 4 X RELAY / 8A Q1 ASR-B120AC ASR-E120AC 8 (0-40VAC) OFF,(80-265VAC) ON N/A N/A 4 NO (8A@240V AC, 5A@30V DC) 0.5 lb. (225 g) + - I1 I2 I3 I4 I5 I6 I7 I8 C1 C2 110 - 230 V AC 50 / 60 Hz ESC FUSE +SUPPLY - Expansion Module 110 - 230 V AC 50 / 60 Hz Cat. No. Digital Inputs Digital Input Range Analog Inputs Analog Input Range Digital Relay Output Weight Input Output Number of Nodes Isolation Voltage Baud Rate Operating temperature Storage temperature LED Indicators Weight FUSE +SUPPLY L N INPUT 8XAC PROGRAM RUN PARAMETER UTILITIES + C1 C2 A O/P 2 AN AN 1 2 INPUT 6 X DC AN1, AN2 = 0 -10 V DC I/P 1 6 36mm (1-27/64”) 52.3mm (2-1/16”) 72mm (2-53/64”) 45mm (1-49/64”) 72mm (2-53/64”) 90mm (3-35/64”) 64.9mm (2-35/64”) N FUSE SUPPLY I1 I2 I3 I4 I5 I6 I7 I8 C1 C2 110 - 230 V AC 50 / 60 Hz RS485 Communication Module (including communication cable) (DC Model) (Priority Driven) 100mm (3-15/16”) K FREE SOFTWARE DOWNLOAD 45mm (1-49/64”) CMY L L N Expansion Module Programming Features 90.5mm (3-9/16”) MY N FUSE SUPPLY FUSE 100mm (3-15/16”) CM L OUTPUT 4 X RELAY / 8A Cat. No. • Supports upto 48 I/Os (32 digital inputs & 16 digital outputs) • DST Feature Available • Backlit LCD Screen for display & modification of pre-selected parameters of functional blocks, viewing I/O status and programming on the device • PC software for programming, online & offline simulation, documentation & printing • Designed for use in automation for commercial & Industrial sectors • Modbus Communication M Y SUPPLY, INPUT & OUTPUT CONNECTIONS Base Module Features C 3 Rated Voltage (Ue): 120/240 V, Rated Current (Ie): 3.0/1.5 A Rated Voltage (Ue): 24/125/250 V, Current (Ie): 2.0/0.22/0.1 A 150h at -10°C to +55°C -10°C to +55°C -25°C to +70°C 95% (Rh) Flame Retardant UL 94-V0 Base / DIN Rail IP 20 for Terminals, IP 40 for Enclosure Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com SmartRelayInsideIeps.pdf 1 9/24/12 1:03 PM Altech Smart Relay Altech Smart Relay Connection Diagrams Technical Specifications I/O Extensions (Max.) Utilization Category AC-15 Smart Relay DC-13 Power Reserve (For Clock Only) Operating Temperature Storage Temperature Humidity (Non Condensing) Enclosure Mounting Degree of Protection LISTED E352868 Standards and Certifications • UL 508 • IEC 61000-3-2 • IEC 61000-4-2-1~11 Supply Voltage (-20% to + 10%) Power Consumption Max. Supply current Digital Inputs Digital Input Range Analog Inputs Analog Input Range Digital Relay Output Weight • 250 lines of ladder programming • 16 soft text messages, Time Switches, Compare Counters, Timers, Counters & 12 analog functions CY Function Blocks Timers: Counters: Time Switches: Compare Counters: Analog Functions: Soft Text Messages: Auxiliary Relays: 16 16 16 16 12 16 32 (ON Delay, Interval, Cyclic ON-OFF, OFF Delay) (Up/Down, Retentive selectable) (Weekly / Daily) AltechCorp.com/SmartRelay Mounting Dimensions 1 2 INPUT 3 4 12 - 24 V DC 5 6 V1 V2 + C1 C2 PROGRAM RUN PARAMETERS UTILITIES 1 2 INPUT 3 4 12 - 24 V DC INPUT 6 X DC V1, V2 = 0 -10 V DC 90.5mm (3-9/16”) + 1 2 3 5 4 5 6 7 Base Module 3 8 B 4 SEL C Q2 Q3 Q4 4.3mm (11/64”) Programmable Smart Relay Base Module ASR-B24DC 110-240 VAC (50/60Hz) 5W 36 mA 8 (0-40VAC) OFF,(80-265VAC) ON N/A N/A 4 NO (8A@240V AC, 5A@30V DC) 0.51 lb. (230 g) 12-24 VDC 5W 360 mA 6 (0-4VDC) OFF,(8-26.4VDC) ON 2 (can be used as Digital Inputs) 0 to 10 VDC 4 NO (8A@240V AC, 5A@30V DC) 0.51 lb. (230 g) OP1 OP2 OP3 TTL Level RS-485 protocol (two wires, D+, D-) 32 standard unit loads 2000 Vrms 300, 600, 1200, 2400, 4800, 9600 -10°C to +55°C -20°C to +70°C Red LED’s for Tx & Rx. Green LED for Power indication 0.19 lb. (84 g) INPUT 8XAC Z1 OK I1 I2 I3 I4 I5 I6 ANAN C1 C2 INPUT 6XDC An1, An2 = 0-10 V DC 12 - 24V DC DEL Z4 ALT PROGRAM RUN PARAMETER UTILITIES Z3 Z2 INPUT 6XDC V1,V2=0-10 VDC 12 - 24V DC DEL Z4 ALT + - I1 I2 I3 I4 I5 I6 V1 V2 C1 C2 Z1 Z3 ESC Z2 OK Q2 Q1 LOAD LOAD ASR-E24DC 6 (0-4VDC) OFF,(8-26.4VDC) ON 2 (can be used as Digital Inputs) 0 to 10 VDC 4 NO (8A@240V AC, 5A@30V DC) 0.5 lb. (225 g) OUTPUT 4 X RELAY / 8A Q1 Q4 Q3 LOAD LOAD Q2 LOAD FUSE LOAD Q3 LOAD Q4 LOAD +SUPPLY - SUPPLY AC Base Module OUTPUT 4 X RELAY / 8A Q1 FUSE LOAD Q2 Q3 LOAD FUSE LOAD OP2 LOAD OP3 OP4 LOAD DC Base Module DC Expansion Module I1 I2 I3 I4 I5 I6 I7 I8 C1 C2 110 - 230 V AC 50 / 60 Hz INPUT 8XAC DEL Z4 ALT PROGRAM RUN PARAMETER UTILITIES Z1 Z3 ESC Z2 OK 485DC OUTPUT 4 X RELAY / 8A ALTECH SAMRT RELAY OUTPUT 4 X RELAY / 8A ASR-SOFT Q1 Q2 Q3 Q4 Q1 Q2 Q3 Fig. 3 Connection Between Base Module & Expansion Q4 Fig. 4 Connection Between Base Module & Communication Module Same for both AC & DC Power Supply Wiring 1. Although the Altech Smart Relay has been designed to withstand the negative effects of any electrical noise that might be present its power supply. It may be necessary to insert an isolation transformer between the supply and line terminals of the Altech Smart Relay. 2. While using the DC Altech Smart Relay, run the 24 VDC Input line separate from 100 ~240V AC power lines. Communication Cable Cat. No. Supply Voltage Weight Rx Tx PORT TTL PORT-RS485 ASR-C485-120AC 110-240 VAC 0.18 lb. (80 g) Wiring of Input/Ouput 1. Separate input and output lines. 2. When the output lines are running close to power supply or input lines, use shielded wires and ground them. ASR-C485-24DC 12-24 VDC 0.19 lb. (84 g) Accessories D+ D- OP4 4.3mm (11/64”) Programmable Smart Relay Expansion Module Programmable Smart Relay Communication Module Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com Cat. No. Weight ASR-MC Memory Card 0.18 lb. (80 g) ASR-USB USB Cable 0.22 lb. (100 g) ASR-RS232 Serial RS232 Cable 0.24 lb. (110 g) Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com LOAD +SUPPLY Fig. 2 L N INPUT 8XAC OP1 LOAD SUPPLY AC Expansion Module I1 I2 I3 I4 I5 I6 I7 I8 C1 C2 Q4 LOAD Fig. 1 L N OUTPUT 4 X RELAY / 8A 12-24 V DC OUTPUT 4 X RELAY / 8A OUTPUT 4 X RELAY / 8A Q1 ASR-B120AC ASR-E120AC 8 (0-40VAC) OFF,(80-265VAC) ON N/A N/A 4 NO (8A@240V AC, 5A@30V DC) 0.5 lb. (225 g) + - I1 I2 I3 I4 I5 I6 I7 I8 C1 C2 110 - 230 V AC 50 / 60 Hz ESC FUSE +SUPPLY - Expansion Module 110 - 230 V AC 50 / 60 Hz Cat. No. Digital Inputs Digital Input Range Analog Inputs Analog Input Range Digital Relay Output Weight Input Output Number of Nodes Isolation Voltage Baud Rate Operating temperature Storage temperature LED Indicators Weight FUSE +SUPPLY L N INPUT 8XAC PROGRAM RUN PARAMETER UTILITIES + C1 C2 A O/P 2 AN AN 1 2 INPUT 6 X DC AN1, AN2 = 0 -10 V DC I/P 1 6 36mm (1-27/64”) 52.3mm (2-1/16”) 72mm (2-53/64”) 45mm (1-49/64”) 72mm (2-53/64”) 90mm (3-35/64”) 64.9mm (2-35/64”) N FUSE SUPPLY I1 I2 I3 I4 I5 I6 I7 I8 C1 C2 110 - 230 V AC 50 / 60 Hz RS485 Communication Module (including communication cable) (DC Model) (Priority Driven) 100mm (3-15/16”) K FREE SOFTWARE DOWNLOAD 45mm (1-49/64”) CMY L L N Expansion Module Programming Features 90.5mm (3-9/16”) MY N FUSE SUPPLY FUSE 100mm (3-15/16”) CM L OUTPUT 4 X RELAY / 8A Cat. No. • Supports upto 48 I/Os (32 digital inputs & 16 digital outputs) • DST Feature Available • Backlit LCD Screen for display & modification of pre-selected parameters of functional blocks, viewing I/O status and programming on the device • PC software for programming, online & offline simulation, documentation & printing • Designed for use in automation for commercial & Industrial sectors • Modbus Communication M Y SUPPLY, INPUT & OUTPUT CONNECTIONS Base Module Features C 3 Rated Voltage (Ue): 120/240 V, Rated Current (Ie): 3.0/1.5 A Rated Voltage (Ue): 24/125/250 V, Current (Ie): 2.0/0.22/0.1 A 150h at -10°C to +55°C -10°C to +55°C -25°C to +70°C 95% (Rh) Flame Retardant UL 94-V0 Base / DIN Rail IP 20 for Terminals, IP 40 for Enclosure Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com SmartRelayOutside.pdf 1 9/24/12 1:35 PM Altech Universal Digital Multi-Timer Altech’s AMT-Series of Universal Digital Multi-Timers comprises 4 models featuring 8 or 18 timer functions to offer highest flexibility in controlling operations. The time range is adjustable from 0.1s to 999h. An LCD display shows current Run time information. Features Multifunctional Timer (8 or 18 Functions) Universal Voltage 24~265 VAC/ DC Wide Time Range: 0.1s ~ 999h 3 Digit LCD Display for Preset Time and Run Time DIN Rail Mounted 17.5mm Width LISTED Digital Timers Cat. No. Output Contacts No. of Timer Functions E351145 AMT8-S1 1 C/O 8 AMT8-D2 2 NO 8 AMT12-S1 1 C/O 18 1) ON Delay [A] 2) Cyclic OFF/ ON [b] 3) Cyclic ON/ OFF [C] 4) Signal ON/ OFF [d] 5) Signal OFF Delay [E] 6) Interval [F] 7) Signal OFF/ ON [G] 8) One Shot Output [H] Functions / [setting mode] 1) ON Delay [0] 2) Cyclic OFF/ ON [1] 3) Cyclic ON/ OFF [2] 4) Impulse on Energizing [3] 5) Accumulative Delay on Signal [4] 6) Accumulative Delay on Inverted Signal [5] 7) Accumulative Impulse on Signal [6] 8) Signal ON Delay [7] 9) Inverted Signal ON Delay [8] 10) Signal OFF Delay [9] 11) Impulse ON/ OFF [A] 12) Signal OFF/ ON [b] 13) Leading Edge Impulse 1 [C] 14) Leading Edge Impulse 2 [d] 15) Trailing Edge Impulse 1 [E] 16) Trailing Edge Impulse 2 [F] 17) Delayed Impulse [G] 18) Inverted Signal ON Delay 2 [H] C M Y CM MY Supply Voltage Power Consumption Timing Range Reset Time Repeat Accuracy Output Contact Rating Electrical Life Mechanical Life AC-15 Rating DC-13 Rating Operating Temperature Storage Temperature Weight Protection Enclosure Protection Terminals Torque Terminal Wire Size 24 - 265 VAC/ DC (50, 60Hz) 10 VA max. 0.1s ~ 999h 200ms max. +-0.5% 8A @ 240 VAC/ 24 VDC (resistive) 10,000 switching cycles 2,000,000 switching cycles Rated Voltage (Ue): 125/ 240V, Rated Current (Ie): 3/1.5A Rated Voltage (Ue): 125/ 250V, Rated Current (Ie): 2/0.22/0.1A -10ºC ~ +55ºC (+14ºF ~ 131ºF) -20ºC ~ +65ºC (-4ºF ~ 149ºF) 85g (0.14lb.) IP30 IP20 0.40 Nm (3.5 lb.in.) 0.3-2.5 mm2 (22-14 AWG) Connection Diagrams Dimensions A1 A1 B1 B1 A2 A2 AMT8-S1, AMT12-S1 67 mm 45 mm K Specifications 100 mm CY CMY AMT12-D2 2 NO 18 Run Time Setting Mode HMS SET ADJ Preset Time Up Down LED Indication for Relay Status Scan this QR code for more information. 76.0 mm 89 mm • • • • • • AMT8-S2, AMT12-S2 17.5 mm Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com Altech Corporation 35 Royal Road Flemington, NJ 08822-6000 P 908.806.9400 • F 908.806.9490 www.altechcorp.com Altech Corp.® 120-3000 Printed October 2012