Fuse Blocks, 5 x 20 and 5 x 25 mm CSFL4U However, an application of such terminals must take into considTerminal Width eration residual current flow. † Fuse not included. DDFL4U - Double Level Fuse Terminal with fuse link on the top level has a separate feed through terminal at the lower level. This eliminates use of an additional feed through terminal. In DDFL4U(E), specially designed built in circuit gives light indication in the event of a fuse blow out at the top level. The terminal provides separate feed through connection possibility at the lower level. 8 mm Height x Length 43 x 58 mm 43 x 58 mm Stripping Length 9.5 mm 9.5 mm Insulation Material Polyamide 6.6 Polyamide 6.6 Type of Connection 2 screw clamps 2 screw clamps 24V AC/DC, 48V AC/DC, 110V AC/DC, 220V AC/DC, 440V AC LED Voltage Type of Fuse Used COLOR BLOCKS When ordering please add color suffix to Cat. No. Example: CTS2.5U-N/R Color Red Blue Black Orange Green Yellow White Beige Dark Brown Ordering Suffix R BU BL O G Y W BG DB * Add required voltage to part number as a suffix. i.e. CSFL4U(L)/24 for 24V AC/DC. Ø5x20, Ø5x25 mm E220514 Wire Range Voltage Rating Isolation Partition (other than grey standard) Ø5x20, Ø5x25 mm Approvals Important: The disconnecting device is not suitable for interrupting load. The Terminal Block supply must be switched off before End Plate operating the slide link/lever. † Fuses are sold separately Altech, see pages 23-24. † Fuse not included. 8 mm DDFL4U(LR): This is a modified Current Rating version of DDFL4U(E) terminal where in two equipotential con- Torque nection points are available on Other Approvals both ends of the terminal. 20 CSFL4U(L)* Altech fuse terminals are also available with light indication CSFL4U(L). A specially designed built-in circuit gives light indication in the event of fuse blow out. Thus, fault in a circuit can be easily located. E220514 22-10 AWG 22-10 AWG 22-10 AWG 22-10 AWG 600 V 600 V 600 V 600 V 6.3 A 10 A 6.3 A 10 A 7 lb-in 7 lb-in 7 lb-in 7 lb-in Cat. No. Std. Pk. Cat. No. Std. CSFL4U 100 CSFL4U(L)* 50 EPCSFL4U 50 EPCSFL4U 50 PPCSFL4U 50 PPCSFL4U 50 CA702 CA802 50 50 CA702 CA802 50 50 CA711/2 CA711/3 CA711/4 CA711/10 100 100 50 20 CA711/2 CA711/3 CA711/4 CA711/10 100 100 50 20 MT8 MT2 100 100 MT8 MT2 100 100 DIN Rail for ordering information refer to page 72 End Stop for ordering information refer to page 74 Internal Jumper Insulated Internal Jumper Current Bar 2 pole 3 pole 4 pole 10 pole 2 pole 3 pole 4 pole 10 pole 2 pole 3 pole 4 pole 10 pole Shorting Sleeve & Screw External Jumper 2 pole 3 pole 4 pole 10 pole Marking Tags (MT Type) (MT Type on Lever) Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com