Model PD0922J7575D2HF

Model PD0922J7575D2HF
Rev B
Ultra Low Profile 0805 Power Divider
75Ω to 75Ω
Description
The PD0922J7575D2HF is a low profile, sub-miniature Wilkinson power divider in
an easy to use surface mount package and is ideal for high volume manufacturing
while delivering higher performances than traditional printed and lumped element
solutions. It has been designed for the following markets: DVB-S, GSM, DCS, PCS,
WCDMA, GPS, 802.11a+g, Bluetooth, and Zigbee USA.
The PD0922J7575D2HF is matched to 75Ω and has a height profile of 0.8 mm. A
two section Wilkinson design results in increased isolation performance. Two
external resistors are required for operation. Components are available on tape and
reel for high volume manufacturing pick and place.
Detailed Electrical Specifications: Specifications subject to change without notice.
ROOM (25°°C)
Features:
•
•
•
•
•
•
•
•
•
•
•
•
950 – 2150 MHz
16 dB Isolation (output ports)
Good Return Loss
0.8mm Height Profile
75Ω Outputs/Inputs
External resistors required
Low Insertion Loss
Surface Mountable
Tape & Reel
Non-conductive Surface
RoHS Compliant
Halogen Free
Parameter
Min.
Frequency
Input Port Impedance
Output Port Impedance
Return Loss
Insertion Loss*
Amplitude Balance
Phase Balance
Isolation (Output Ports)
Power Handling
950
Operating Temperature
-55
Typ.
75
75
11
0.8
0.4
2
16
9.5
14
Max
Unit
2150
2
MHz
Ω
Ω
dB
dB
dB
Degrees
dB
Watts
+85
ºC
1.0
0.7
3
* Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC)
Outline Drawing
TOP VIEW (Near Side)
SIDE VIEW
BOTTOM VIEW (Far Side)
4x 0.37
2.04±0.10
0.81±0.08
1
3
2
2x 0.15
1.29±0.10
6x 0.98
Orientation Marker
Denotes Pin Location
Orientation Marker
Denotes Pin Location
Mechanical Outline
-Dimensions are in Millimeters
Pin
1
2
3
4
5
6
6x
0.22
6
5
4
4x 0.65
6x
0.30
Designation
Output 1
Input
Mid 2
Mid 1
GND
Output 2
Visit us at
www.anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
Model PD0922J7575D2HF
Rev B
Typical Broadband Performance: 500 MHz. to 8.0 GHz.
Insertion Loss
0
-3
-3
-6
-6
-9
-12
-12
-15
-15
Frequency [MHz]
7000
7500
8000
7000
7500
8000
5000
5000
4500
4000
3500
3000
2500
2000
1500
8000
7500
7000
-20
6500
-2
6000
-15
5500
-1.5
5000
-10
4500
-5
-1
4000
-0.5
1000
0
500
0
3500
6500
5
3000
6000
0.5
2500
6500
10
2000
6000
15
1
1500
5500
1.5
deg
20
1000
4500
Phase Balance
2
500
4000
Frequency [MHz]
Amplitude Balance
[dB]
5500
Frequency [MHz]
3500
3000
2500
500
8000
7500
7000
6500
6000
5500
5000
4500
4000
3500
-36
3000
-33
-36
2500
-30
-33
2000
-27
-30
1500
-24
-27
1000
-21
-24
2000
-18
-21
1500
-18
1000
[dB]
-9
500
[dB]
Return Loss - Input
0
Frequency [MHz]
Isolation
0
-3
-6
-9
-12
-18
-21
-24
-27
-30
-33
8000
7500
7000
6500
6000
5500
5000
4500
4000
3500
3000
2500
2000
1500
1000
-36
500
[dB]
-15
Frequency [MHz]
Visit us at
www.anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
Model PD0922J7575D2HF
Rev B
Typical Performance: 900 MHz. to 2200 MHz.
Insertion Loss
-3
-0.3
-6
-0.6
-9
-0.9
-12
-1.2
-15
-1.5
1.5
15
1
10
0.5
5
2200
2100
2000
1900
1800
2200
2100
2000
1900
1800
1700
1600
1500
1400
1300
1200
2200
2100
2000
1900
1800
1700
-20
1600
-2
1500
-15
1400
-1.5
1300
-10
1200
-1
1100
-0.5
1100
0
-5
1000
0
900
deg
20
1000
1700
Phase Balance
Amplitude Balance
2
900
1600
Frequency [MHz]
Frequency [MHz]
[dB]
1500
1400
1300
900
2200
2100
2000
1900
1800
1700
1600
1500
-3.6
1400
-3.3
-36
1300
-3.0
-33
1200
-2.7
-30
1100
-2.4
-27
1000
-2.1
-24
1200
-1.8
-21
1100
-18
1000
[dB]
0.0
900
[dB]
Return Loss - Input
0
Frequency [MHz]
Frequency [MHz]
Isolation
0
-3
-6
-9
-12
-18
-21
-24
-27
-30
-33
2200
2100
2000
1900
1800
1700
1600
1500
1400
1300
1200
1100
1000
-36
900
[dB]
-15
Frequency [MHz]
Visit us at
www.anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
Model PD0922J7575D2HF
Rev B
Mounting Configuration:
In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be
used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet
published specifications.
All of the Xinger components are constructed from organic PTFE based composites which possess excellent
electrical and mechanical stability. Xinger components are compliant to a variety of ROHS and Green standards and
ready for Pb-free soldering processes. Pads are Gold plated with a Nickel barrier.
An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the
transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying
pick and place equipment tolerances. In addition, since the PD0922J7575D2HF is a Wilkinson power divider,
external 0402 150Ω and 300Ω resistors must be mounted in locations R1 and R2 respectively, as shown in the
Figure below.
Pad Footprint w/ 0402 Resistor Locations
Circuit Pattern
Dimensions are in Millimeters
Mounting Footprint
Footprint Pad (s)
Solder Resist
3x Transmission
lines
.04
R1
4x
.25
.66
R2
6x .41
6x .33
Plated thru
holes to ground
Visit us at
www.anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
Model PD0922J7575D2HF
Rev B
Packaging and Ordering Information
Parts are available in reel and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order
quantities are 4000 per reel. See Model Numbers below for further ordering information.
1.00
2.00
4.00
1.75
3.50
8.00
1.60
4.00
2.41
.25
Visit us at
www.anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282