For more information, please visit the product page. date 05/06/2015 page 1 of 4 SERIES: PSE-1200 │ DESCRIPTION: AC-DC HOT-SWAP POWER SUPPLY FEATURES up to 1200 W continuous power low profile sub-1U package I2C communication for monitoring and control redundant (N+1) operation blind mate connections for hot-swap power factor correction active current sharing remote on/off control, power good efficiency up to 90% T o of N C rt Rheinla nd UV , I nc. • • • • • • • • • h A ca meri US MODEL PSE-1200-12 Notes: output voltage output current output power1,2 ripple and noise efficiency3 (Vdc) max (A) max (W) max (mVp-p) typ (%) 12 100 1200 120 90 1. At 115 Vac input, maximum of 1000 W 2. At 230 Vac input, maximum of 1200 W 3. At 230 Vac input, 50% load. PART NUMBER KEY PSE-1200 - 12 - CXX Base Number Output Voltage cui.com Reserved for Custom Configurations For more information, please visit the product page. CUI Inc │ SERIES: PSE-1200 │ DESCRIPTION: AC-DC HOT-SWAP POWER SUPPLY date 05/06/2015 │ page 2 of 4 INPUT parameter conditions/description min voltage typ 90 frequency 50 current at 115 Vac, 1000 W at 230 Vac, 1200 W inrush current half cycle, cold start, 25°C at 115 Vac, 60 Hz at 230 Vac, 50 Hz leakage current power factor correction 0.95 0.99 min typ max units 264 Vac 60 Hz 10.2 6.2 A A 25 30 A A 1.5 mArms max units OUTPUT - V1 (MAIN OUTPUT) parameter conditions/description regulation transient response ±2 25% step load, recovery to 1% within 1 ms % 2 % max units OUTPUT - VSB (STANDBY OUTPUT) parameter conditions/description output voltage VSB1 VSB2 min typ output current VSB1 VSB2 500 250 mA mA ripple and noise VSB1 VSB2 240 150 mVp-p mVp-p regulation VSB1 VSB2 10.5 14.5 Vdc % parameter conditions/description min typ max units I C interface I C (SCL/SDA); addresses (A0, A1, A2) remote sense main only, compensates for VDrop current share signal wire active current share parallel operation parallel non-redundant or N+1 typ max units 12 5 ±5 Vdc Vdc STATUS & CONTROL 2 2 PROTECTIONS parameter conditions/description min over voltage protection inception point shutdown 120 % over current protection V1: hiccup mode after 100 ms auto recovery 120 % over temperature protection output shut down, auto recovery SAFETY & COMPLIANCE parameter conditions/description safety approvals cTUVus UL60950-1, CE (LVD) min emissions FCC 15 Sub Part J, Class A, EN55022 Class A harmonic compliance EN61000-3-2 Class A surges (mains) IEC/EN 61000-4-5 voltage dips/interruptions IEC/EN 61000-4-11 RoHS 2011/65/EU cui.com typ max units For more information, please visit the product page. CUI Inc │ SERIES: PSE-1200 │ DESCRIPTION: AC-DC HOT-SWAP POWER SUPPLY date 05/06/2015 │ page 3 of 4 ENVIRONMENTAL parameter conditions/description min operating temperature storage temperature max units 0 typ 50 °C -40 85 °C MECHANICAL parameter conditions/description dimensions 10.00 x 4.00 x 1.60 (254.0 x 102.4 x 40.6 mm) min cooling / airflow integral high performance 38 mm fan, air inlet at face; exhaust at connector input / output connector FCI P/N 51939-103LF mates with FCI P/N 51866-025LF hot-swap capability fully hot-swappable, blind mate connector typ max units inches MECHANICAL DRAWING units: inches [mm] tolerance: X.XX ±0.02 [0.50] X.XXX ±0.010 [0.25] P1 P2 P3 P4 P5 P6 P7 P8 P9 D 1 2 3 4 5 6 C B A INPUT / OUTPUT CONNECTOR Pins Function Pins Function Pins Function Pins Function Pins P1 Line P2 Neutural A1 ISHARE A2 I2C clock (SCL) P3 Earth/Ground A3 P4 -12 V A4 P5 -12 V P6 -12 V P7 P8 P9 B1 - Sense C1 Secondary Return D1 + Sense B2 Reserved C2 V Margin D2 Short Pin A1 address (I2C) B3 A0 Address (I2C) C3 12 VSB D3 EEPROM DAT (SDA) -- B4 Reserved C4 5 VSB D4 A2 Address (I2C) A5 AC Fail B5 Module Present (out) C5 Module Present (in) D5 -- A6 Signal Return B6 Module Alarm C6 Module Disable D6 Temp Alarm +12 V -- -- -- -- -- -- -- -- +12 V -- -- -- -- -- -- -- -- +12 V -- -- -- -- -- -- -- -- cui.com Function For more information, please visit the product page. CUI Inc │ SERIES: PSE-1200 │ DESCRIPTION: AC-DC HOT-SWAP POWER SUPPLY date 05/06/2015 │ page 4 of 4 REVISION HISTORY rev. 1.0 description date initial release 05/06/2015 The revision history provided is for informational purposes only and is believed to be accurate. Headquarters 20050 SW 112th Ave. Tualatin, OR 97062 800.275.4899 Fax 503.612.2383 cui.com [email protected] CUI offers a two (2) year limited warranty. Complete warranty information is listed on our website. CUI reserves the right to make changes to the product at any time without notice. Information provided by CUI is believed to be accurate and reliable. However, no responsibility is assumed by CUI for its use, nor for any infringements of patents or other rights of third parties which may result from its use. CUI products are not authorized or warranted for use as critical components in equipment that requires an extremely high level of reliability. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.