IA6008-FB10A Contact image sensor heads Color image sensor heads for multi-function IA6008-FB10A “Color contact image sensor” with optical system intended for Flatbed scanning. Optical technology established for sheet-feed scanning has been further advanced for Flatbed scanning. Furthermore, a newly developed sensor with resolution selection function provides more freedome in choosing the adequate optical resolution matching to the application. zApplications Image sensor heads device for multiple function facsimiles such as color scanner and multiple function printer. zFeatures 1) Signal amplifier is built in to the image sensor IC in order to increase immunity to external noise. 2) A low-voltage drive sensor is employed, which runs at 3.3V like ASIC 3) The LED light source is mounted on the same substrate as the sensor chip which makes it possible to package the device with lighter weight and an extremely small size. 4) With the proprietary prism, the output signal is maintained uniformly. 5) The ceramic substrate is used for excellent dimensional accuracy and thermal stability. zExternal dimensions (Unit : mm) 236±0.5 216 (Effective Reading With) 2−φ 1.5x2 Oval Hole D4MIN 9.4 0.324 ±0.1 Effective 1st bit + 17.5 14 ± 0.2 14 ± 0.2 Scanning Line + 2−φ 1.5 D4MIN 2− 15 5 + 0 0.0 3− 2 ±0.2 MAX 3.15 max.1 max.1 max.1 max.1 6.9 6.9 1mm pitch 12pin Pin No. No.1 No.2 No.3 No.4 No.5 No.6 Signal Ao MODE GND VDD VREF SP Pin No. No.7 No.8 No.9 No.10 No.11 No.12 No.12 Center of FCC No.1 13.8 Signal CLK V-LED B-GND G-GND R-GND NC 1/5 IA6008-FB10A Contact image sensor heads zCharacteristics Parameter Symbol Typ. Unit Effective scanning width − 217 mm Primary scan dot density − 600 dpi − 5184 dots Power supply voltage VDD 3.3 V Reference voltage VREF 0.8 V Scanning speed SLT 4.5 ms / line Total dot number CLK 5 MHz Maximum dynamic range VRMax 0.75 V Minimum dynamic range VRMim. 0.375 V Vod VREF + − 0.1 V − 5 to 45 °C Clock frequency Dark output Operating temperature zPin assignments No. Circuit I/O 1 AO O Analog output Function 2 MODE I Mode select 3 GND I Ground 4 VDD I Power supply 5 VREF I Reference voltage 6 SP I Start pulse 7 CLK I Clock 8 V-LED I LED power supply 9 B-GND I BLUE LED ground 10 G-GND I GREEN LED ground 11 R-GND I RED LED ground 12 NC − − 2/5 IA6008-FB10A Contact image sensor heads zTiming chart (a) CLK Timing Chart 1/fCLK twH twL CLK 50% 50% SP tSETUP tHOLD ts Ao 1pixel 2pixel (b) Data Output Timing Chart (600dpi mode) After turning on the SP pulse, the analog output starts from the setting up point of 64 clock pulse. 1 2 82 83 84 136 137 138 CLK SP Ao Vref output period(52pixels) Vdummy Analog output period 1 to 82pixels 83 to 136pixels 137 to 5266pixels Note)The CLK section area which is over the effective pixel numbers (Output blank part) cannot be used as the analog Output standard level. 3/5 IA6008-FB10A Contact image sensor heads Data Output Timing Chart (300dpi mode) After turning on the SP pulse, the analog output starts from the setting up point of 64 clock pulse. 1 2 82 83 84 109 110 111 CLK SP Ao Vref output period(52pixels) Vdummy Analog output period 1 to 82pixels 83 to 109pixels 110 to 2674pixels Note)The CLK section area which is over the effective pixel numbers (Output blank part) cannot be used as the analog Output standard level. zCircuit diagram VDD 1µF×3 GND 1 5184 SP ANALOG MEMORY CIRCUIT CLK VDD VREF AO VREF VLED RGND GGND BGND 4/5 IA6008-FB10A Contact image sensor heads zPeripheral circuit CIS UNIT 12 9 10 11 8 1 5 4 6 7 R3 3 2 GND MODE R1 R2 B G R C5 A C1 C3 NC C2 LED GND C4 VLED VREF VDD SP CLK R1=R2=100Ω, R3=100KΩ C1=C2=47µF C3=100µF, C4=0.1µF, C5=100pF 5/5 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1