HMC594


Design Assistance

Customised Pack Sizes / Qtys

Assembly Assistance

Support for all industry recognised
supply formats:

Die handling consultancy

Hi-Rel die qualification

Hot & Cold die probing

Electrical test & trimming
o Waffle Pack
o Gel Pak
o Tape & Reel

Onsite storage, stockholding &
scheduling

100% Visual Inspection
o MIL-STD 883 Condition A
o MIL-STD 883 Condition A

On-site failure analysis

Bespoke 24 Hour monitored
storage systems for secure long
term product support

On-site failure analysis
Contact
[email protected]
For price, delivery and to place orders
HMC594
www.analog.com
www.micross.com
Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC594
v01.0312
Amplifiers - Low Noise - CHIP
GaAs pHEMT MMIC LOW NOISE
AMPLIFIER, 2 - 4 GHz
Typical Applications
Features
The HMC594 is ideal for:
Gain Flatness: ±0.2 dB
• Fixed Microwave
Noise Figure: 2.6 dB
• Point-to-Multi-Point Radios
Gain: 10 dB
• Test & Measurement Equipment
OIP3: +36 dBm
• Radar & Sensors
DC Supply: +6V @ 100 mA
• Military & Space
50 Ohm Matched Input/Output
Die Size: 1.32 x 1.21 x 0.10 mm
General Description
Functional Diagram
The HMC594 is a GaAs PHEMT MMIC Low Noise
Amplifier (LNA) chip which operates from 2 to 4 GHz.
The HMC594 features extremely flat performance
characteristics including 10 dB of small signal gain,
2.6 dB of noise figure and output IP3 of +36 dBm
across the operating band. This versatile LNA is ideal
for hybrid and MCM assemblies due to its compact
size, consistent output power and DC blocked RF
I/O’s. All data is measured with the chip in a 50 Ohm
test fixture connected via one 0.025 mm (1 mil) diameter bondwire of minimal length 0.31 mm (12 mil).
Electrical Specifications, TA = +25° C, Vdd= +6V, Idd= 100mA*
Parameter
Min.
Frequency Range
Gain
Typ.
7
Gain Variation Over Temperature
dB
dB/ °C
2.6
15
Saturated Output Power (Psat)
18
GHz
10
Input Return Loss
Output Return Loss
Units
0.015
Noise Figure
Output Power for 1 dB Compression (P1dB)
Max.
2-4
3.5
dB
dB
15
dB
21
dBm
22
dBm
Output Third Order Intercept (IP3)
36
Supply Current (Idd)
100
dBm
130
mA
*Adjust Vgg between -1.5V to -0.5V to achieve Idd = 100mA
1
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC594
v01.0312
GaAs pHEMT MMIC LOW NOISE
AMPLIFIER, 2 - 4 GHz
Broadband Gain & Return Loss
Gain vs. Temperature
15
11
S21
S11
S22
0
10
GAIN (dB)
RESPONSE (dBm)
5
-5
-10
-15
9
8
+25C
+85C
-55C
7
-20
6
-25
-30
5
1
2
3
4
5
6
7
8
2
9
2.25
2.5
FREQUENCY (GHz)
Input Return Loss vs. Temperature
3.25
3.5
3.75
4
0
-5
RETURN LOSS (dB)
+25C
+85C
-55C
-5
RETURN LOSS (dB)
3
Output Return Loss vs. Temperature
0
-10
-15
-20
+25C
+85C
-55C
-10
-15
-20
-25
-25
-30
2
2.25
2.5
2.75
3
3.25
3.5
3.75
4
2
2.25
2.5
FREQUENCY (GHz)
2.75
3
3.25
3.5
3.75
4
FREQUENCY (GHz)
Noise Figure vs. Temperature
Reverse Isolation vs. Temperature
10
0
-5
ISOLATION (dB)
8
NOISE FIGURE (dB)
2.75
FREQUENCY (GHz)
Amplifiers - Low Noise - CHIP
12
10
+25C
+85C
-55C
6
4
2
+25C
+85C
-55C
-10
-15
-20
-25
0
-30
2
2.5
3
FREQUENCY (GHz)
3.5
4
2
2.25
2.5
2.75
3
3.25
3.5
3.75
4
FREQUENCY (GHz)
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
2
HMC594
v01.0312
GaAs pHEMT MMIC LOW NOISE
AMPLIFIER, 2 - 4 GHz
26
25
25
24
24
23
23
Psat (dBm)
P1dB (dBm)
Psat vs. Temperature
26
22
21
20
19
22
21
20
19
+25C
+85C
-40C
18
+25C
+85C
-40C
18
17
17
16
16
2
2.25
2.5
2.75
3
3.25
3.5
3.75
4
2
2.25
2.5
2.75
FREQUENCY (GHz)
3
3.25
3.5
3.75
4
12 14
16
FREQUENCY (GHz)
Output IP3 vs. Temperature
Power Compression @ 3 GHz
25
40
Pout (dBm), GAIN (dB), PAE (%)
38
36
34
OIP3 (dBm)
Amplifiers - Low Noise - CHIP
P1dB vs. Temperature
32
30
+25C
+85C
-40C
28
26
24
22
15
10
20
2
2.25
2.5
2.75
3
3.25
3.5
3.75
Pout
Gain
PAE
20
5
0
-10 -8
4
-6
-4
FREQUENCY (GHz)
-2
0
2
4
6
8
10
INPUT POWER (dBm)
GAIN (dB), P1dB (dBm), Psat (dBm), OIP3 (dBm)
Gain, Noise Figure & Power vs.
Supply Voltage @ 3 GHz
40
35
Gain
P1dB
Psat
OIP3
30
25
20
15
10
5
5.5
6
6.5
Vdd SUPPLY VOLTAGE (Vdc)
3
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC594
v01.0312
GaAs pHEMT MMIC LOW NOISE
AMPLIFIER, 2 - 4 GHz
Drain Bias Voltage (Vdd)
+7 Vdc
RF Input Power (RFIN)(Vdd = +6.0 Vdc)
+15 dBm
Channel Temperature
175 °C
Continuous Pdiss (T= 85 °C)
(derate 11.7 mW/°C above 85 °C)
0.76 W
Thermal Resistance
(channel to die bottom)
85 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-55 to +85 °C
Vdd (Vdc)
Idd (mA)
+5.5
97
+6.0
100
+6.5
103
Note: Amplifier will operate over full voltage ranges shown
above.
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
Die Packaging Information [1]
Standard
Alternate
GP-1 (Gel Pack)
[2]
[1] Refer to the “Packaging Information” section for die
packaging dimensions.
[2] For alternate packaging information contact Hittite
Microwave Corporation.
Amplifiers - Low Noise - CHIP
Typical Supply Current vs. Vdd
Absolute Maximum Ratings
NOTES:
1. ALL DIMENSIONS ARE IN INCHES [MM]
2. DIE THICKNESS IS .004”
3. TYPICAL BOND IS .004” SQUARE
4. BACKSIDE METALLIZATION: GOLD
5. BOND PAD METALLIZATION: GOLD
6. BACKSIDE METAL IS GROUND.
7. CONNECTION NOT REQUIRED FOR UNLABELED BOND PADS.
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
4
HMC594
v01.0312
GaAs pHEMT MMIC LOW NOISE
AMPLIFIER, 2 - 4 GHz
Pad Descriptions
Pad Number
Function
Description
GND
Die bottom must be connected to RF/DC ground. Grounding of pads
1, 3, and 6 is optional. RF performance may be improved through
grounding of these pads. No connection is required to pad 4.
2
RFIN
This pad is AC coupled and matched to
50 Ohms from 2 - 4 GHz.
5
Vdd
Power Supply Voltage for the amplifier. External bypass capacitors
of 100 pF and 0.1 µF are required.
7
RFOUT
This pad is AC coupled and matched to
50 Ohms from 2 - 4 GHz.
8
Vgg
Gate supply voltage for the amplifier. External bypass capacitors of
100 pF and 0.1 µF are required.
Amplifiers - Low Noise - CHIP
1, 3, 4, 6
5
Die Bottom
Interface Schematic
Assembly Diagram
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC594
v01.0312
GaAs pHEMT MMIC LOW NOISE
AMPLIFIER, 2 - 4 GHz
The die should be attached directly to the ground plane eutectically or with
conductive epoxy (see HMC general Handling, Mounting, Bonding Note).
50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina thin film
substrates are recommended for bringing RF to and from the chip (Figure 1). If
0.254mm (10 mil) thick alumina thin film substrates must be used, the die should be
raised 0.150mm (6 mils) so that the surface of the die is coplanar with the surface
of the substrate. One way to accomplish this is to attach the 0.102mm (4 mil) thick
die to a 0.150mm (6 mil) thick molybdenum heat spreader (moly-tab) which is then
attached to the ground plane (Figure 2).
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
0.076mm
(0.003”)
RF Ground Plane
Microstrip substrates should be brought as close to the die as possible in order to
minimize bond wire length. Typical die-to-substrate spacing is 0.076mm (3 mils).
Handling Precautions
0.127mm (0.005”) Thick Alumina
Thin Film Substrate
Follow these precautions to avoid permanent damage.
Storage: All bare die are placed in either Waffle or Gel based ESD protective
containers, and then sealed in an ESD protective bag for shipment. Once the
sealed ESD protective bag has been opened, all die should be stored in a dry
nitrogen environment.
Cleanliness: Handle the chips in a clean environment. DO NOT attempt to clean
the chip using liquid cleaning systems.
Static Sensitivity: Follow ESD precautions to protect against > ± 250V ESD
strikes.
Transients: Suppress instrument and bias supply transients while bias is applied.
Use shielded signal and bias cables to minimize inductive pick-up.
General Handling: Handle the chip along the edges with a vacuum collet or with
a sharp pair of bent tweezers. The surface of the chip has fragile air bridges and
should not be touched with vacuum collet, tweezers, or fingers.
Mounting
The chip is back-metallized and can be die mounted with AuSn eutectic preforms or
with electrically conductive epoxy. The mounting surface should be clean and flat.
Figure 1.
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
0.076mm
(0.003”)
RF Ground Plane
0.150mm (0.005”) Thick
Moly Tab
0.254mm (0.010”) Thick Alumina
Thin Film Substrate
Amplifiers - Low Noise - CHIP
Mounting & Bonding Techniques for Millimeterwave GaAs MMICs
Figure 2.
Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work
surface temperature of 255 °C and a tool temperature of 265 °C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip
temperature should be 290 °C. DO NOT expose the chip to a temperature greater than 320 °C for more than 20 seconds. No more
than 3 seconds of scrubbing should be required for attachment.
Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the
perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule.
Wire Bonding
Ball or wedge bond with 0.025 mm (1 mil) diameter pure gold wire is recommended. Thermosonic wirebonding with a nominal stage
temperature of 150 °C and a ball bonding force of 40 to 50 grams or wedge bonding force of 18 to 22 grams is recommended. Use
the minimum level of ultrasonic energy to achieve reliable wirebonds. Wirebonds should be started on the chip and terminated on
the package or substrate. All bonds should be as short as possible <0.31 mm (12 mils).
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
6