HMC690


Design Assistance

Customised Pack Sizes / Qtys

Assembly Assistance

Support for all industry recognised
supply formats:

Die handling consultancy

Hi-Rel die qualification

Hot & Cold die probing

Electrical test & trimming
o Waffle Pack
o Gel Pak
o Tape & Reel

Onsite storage, stockholding &
scheduling

100% Visual Inspection
o MIL-STD 883 Condition A
o MIL-STD 883 Condition A

On-site failure analysis

Bespoke 24 Hour monitored
storage systems for secure long
term product support

On-site failure analysis
Contact
[email protected]
For price, delivery and to place orders
HMC690
www.analog.com
www.micross.com
Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC690
v04.0709
10 Gbps TRANSIMPEDANCE
AMPLIFIER
Typical Applications
Features
The HMC690 is ideal for:
Supports data rates up to 11.3 Gbps
• SONET OC-192 and SDH STM-64 Transponders
1.25 Kohm differential gain
• 10 Gbps Ethernet
+3.3 V single power supply
• Broadband instrumentation
AC or DC coupled outputs
• Short, intermediate and long reach
optical receiver modules
11 pA/√Hz input referred noise density
3 mA p-p overload
Average input power monitoring
TRANSIMPEDANCE AMPLIFIERS - CHIP
5
Output offset adjustment
Die Size: 0.68 x 1.14 x 0.18mm
Functional Diagram
General Description
The HMC690 is 10 Gbps transimpedance amplifier
designed for SONET OC-192 / SDH STM-64, 10GbE
and 10Gbps systems employing optical amplifiers. It
supports data rates up to 11.3 Gbps. This amplifier
provides a differential output voltage that is proportional
to an applied current at its input port. This current is
typically provided by a photodiode. Operating from a
single +3.3V supply, the HMC690 features low input
referred noise, and is designed for driving a CDR or
a typical transceiver directly. The RSSI output can be
used for monitoring average input power. This device
also features a DC offset control, which enables
output signal level adjustment for asymmetrical
signals. Additional features include an integrated
300Ω filter resistor for photo-diode supply voltage and
an extended linear range[2] option.
Electrical Specifi cations, TA = +25° C, Vcc1 = Vcc2 = +3.3V [1]
Parameter
Conditions
Min.
Typ.
Max.
Units
AC Specifications
Max Data Rate
Small Signal Transimpedance (ZT)
Output Amplitude Differential peak-to-peak
Small Signal Zt BW
11.3
Gbps
Differential p-p @ 500 MHz
1.1
1.25
1.55
For IIN > 1 mA
430
500
560
kOhm
mV
3-dB Upper LImit
7.5
GHz
Noise Density @ 1 GHz
11.2
13.5
pA/√Hz
Noise Density @ 5 GHz
13.4
14.7
pA/√Hz
@ 8 GHz Bandwidth
1.0
Input Referred Noise Density
Input Referred RMS Noise
Added p-p Deterministic Jitter
Random Jitter
IIN > 1 mA
Rise Time
20 - 80%
17
uA rms
10
ps
300
500
fs rms
21
25
ps
[1] Lin_en Open
[2] Please see Pin Description table for further explanation of the extended linear range option available on Pin 9.
5-2
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC690
v04.0709
10 Gbps TRANSIMPEDANCE
AMPLIFIER
Electrical Specifi cations (Conditions)
Conditions
Min.
Typ.
Max.
22
28
Fall Time
80% - 20%
19
Output Return Loss
F<10 GHz
10
Units
ps
dB
Zt Group Delay Variation
±20
ps
Linear Input Range
300
uA p-p
3
mA p-p
-20
dBm
Input Overdrive
@ 10 Gbps (P = 0.9A/W,
re = 9 dB, BER = 1e-12)
Optical Sensitivity [1]
DC Specifications
Power Supply
3.0
3.3
3.6
V
Supply Current
77
92
106
mA
OFF ADJ Sensitivity
780
RSSI Sensitivity
mV/V
-1
Open Circuit Input DC Level
mA/V
0.95
1.1
V
[1] Optical receiver sensitivity depends on packaging, photodiode type, BER value and input signal eye quality.
Photodiode Specifi cation Assumptions
Photodiode Capacitance: (Cpd) = 220 fF
Photodiode and bond wire parasitic inductance:
(Ls) = 800 pH
Photodiode Resistance: (Rs) = 20 Ohm
Photodiode Responsivity: (p) = 0.8 A/W
Differential Output Voltage
vs. Temperature
DIFFERENTIAL OUTPUT AMPLITUDE (mV)
DIFFERENTIAL OUTPUT AMPLITUDE (mV)
Differential Output Voltage
vs. Input Current
600
500
400
300
200
100
0
0
500
1000
1500
2000
2500
PEAK TO PEAK INPUT CURRENT (uA)
3000
5
515
505
495
TRANSIMPEDANCE AMPLIFIERS - CHIP
Parameter
485
475
-60
-40
-20
0
20
40
60
80
100
TEMPERATURE (deg C)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5-3
HMC690
v04.0709
10 Gbps TRANSIMPEDANCE
AMPLIFIER
Peak to Peak Jitter
vs. Peak to Peak Input Current [2]
RMS Jitter vs. Input Current [1]
3.5
25
PEAK TO PEAK JITTER (ps)
RMS JITTER (ps)
3
2.5
2
1.5
1
20
15
10
5
0.5
5
0
0
0
200
400
600
800
1000 1200 1400 1600 1800
0
500
1500
2000
2500
3000
Fall Time vs. Peak to Peak Input Current
30
30
25
25
FALL TIME (ps)
RISE TIME (ps)
1000
PEAK TO PEAK INPUT CURRENT (uA)
Rise Time vs. Peak to Peak Input Current
20
15
10
5
20
15
10
5
0
0
0
500
1000
1500
2000
2500
3000
0
500
PEAK TO PEAK INPUT CURRENT (uA)
1000
1500
2000
2500
3000
PEAK TO PEAK INPUT CURRENT (uA)
Transimpedance vs.
Frequency Over Temperature [3]
Output Return Loss
vs. Frequency Over Temperature [3]
70
20
60
10
RETURN LOSS (dB)
TRANSIMPEDANCE (dB-Ohm)
TRANSIMPEDANCE AMPLIFIERS - CHIP
PEAK TO PEAK INPUT CURRENT (uA)
50
40
+25C
+85C
- 55C
30
20
+25C
+85C
- 55C
0
-10
-20
10
-30
0
1
2
3
4
5
6
FREQUENCY (GHz)
7
8
9
10
1
2
3
4
5
6
7
8
9
FREQUENCY (GHz)
[1] Measured with 10 Gbps 10101 pattern with an estimated bondwire parasitic inductance of 1 nH, source jitter not de-embedded.
[2] Measured with PRBS 2ˆ15-1 pattern at 10 Gbps with an estimated bondwire parasitic inductance of 1 nH. Source jitter not de-embedded.
[3] Single-Ended OUTN
5-4
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
10
HMC690
v04.0709
10 Gbps TRANSIMPEDANCE
AMPLIFIER
RSSI Output Voltage
vs. Input Current Over Temperature
Output Offset Voltage vs. DC Offset
Control Voltage Over Temperature
0.6
3
0.4
OUTPUT OFFSET (V)
3.5
2
1.5
+25C
+85C
- 55C
1
0.2
0
+25C
+85C
- 55C
-0.2
-0.4
0.5
0
0
200
400
600
800
1000
1200
1400
INPUT CURRENT (uA)
-0.6
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
5
DC OFFSET CONTROL VOLTAGE (V)
Eye Diagram [4]
TRANSIMPEDANCE AMPLIFIERS - CHIP
RSSI (V)
2.5
[1] Measured with 10 Gbps 10101 pattern with an estimated bondwire parasitic inductance of 1 nH, source jitter not de-embedded.
[2] Measured with PRBS 2ˆ15-1 pattern at 10 Gbps with an estimated bondwire parasitic inductance of 1 nH. Source jitter not de-embedded.
[3] Single-Ended OUTN
[4] Output Eye measured on Eval board with 1 mA p-p input current. (10 Gbps), 25C, 3.3V, 2ˆ23-1 pattern
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5-5
HMC690
v04.0709
10 Gbps TRANSIMPEDANCE
AMPLIFIER
Supply Current vs. Supply Voltage
Over Temperature
SUPPLY CURRENT (mA)
120
110
100
90
80
+25C
+85C
- 55C
70
5
60
3.1
3.2
3.3
3.4
3.5
TRANSIMPEDANCE AMPLIFIERS - CHIP
SUPPLY VOLTAGE (V)
5-6
Optical Sensitivity Calculation
Optical sensitivity is determined from the input-referred rms noise current, IN. To achieve a bit error rate of 1E-12 , the
signal-to-noise ratio must be 14:1.
S = 10 log
I
x
( SNR
2
N
x
re + 1
re - 1
)
x 1000 dBm
Where
S
= sensitivity (dBm)
SNR
= signal to noise ratio (dB)
IN
= input-referred rms noise current (A)
= photodetector responsitivity (A/W)
= extinction ratio (dB)
re
Optical Minimum Output Swing at Sensitivity Limit Calculation
The typical optical sensitivity is -19 dBm. At the input level, the voltage swing at output of the HMC690 is calculated
as follows:
Save = 10 log
r +1
x
( OMA
)
2
r -1
e
e
Where
Save
= average sensitivity (dBm)
OMA
= optical modulation amplitude (Wp-p)
re
= extinction ratio (dB)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC690
v04.0709
10 Gbps TRANSIMPEDANCE
AMPLIFIER
Absolute Maximum Ratings
4V
Off_adj Voltage
4V
Lin_EN Voltage
4V
Continuous Input Current
8 mA
Junction Temperature
125 °C
Continuous Pdiss (T=85 °C)
(derate 9 mW/ °C Above +85 °C
0.36 W
Thermal Resistance
(Junction to die bottom)
111 °C/W
Storage Temperature
-65 to 120 °C
Operating Temperature
-40 to +85 °C
5
Outline
Die Packaging Information
[1]
Standard
Alternate
WP-26 (Waffle Pack)
[2]
TRANSIMPEDANCE AMPLIFIERS - CHIP
Supply Voltage
[1] Refer to the “Packaging Information” section for die
packaging dimensions.
[2] For alternate packaging information contact Hittite
Microwave Corporation.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5-7
HMC690
v04.0709
10 Gbps TRANSIMPEDANCE
AMPLIFIER
Pad Descriptions
Pad Number
Function
Description
1, 6, 13
GND
Ground connection for TIA.
2
TEST
Test Input. This pad is connected internally to IN thru 1kΩ.
No external connection required.
3
IN
TIA Input.
4
FILTER
Provides bias voltage for photo diode (PD)
thru a 300Ω resistor for Vcc1.
5, 7
Vcc1
Power Supply for input stage and PD.
8, 15
Vcc2
Power supply for output buffers.
9
Lin_EN
HMC690 has an extended linear range feature. With this
feature disabled (pin 9 floating), the HMC690 operates
linearly for inputs less than 300 μAp-p. For input currents
greater than 300 μAp-p, the HMC690 begins to operate
within a saturated region. For input currents greater than
1 mA-p-p, the output is fully saturated. Enabling (pin 9
connected to 3.3V) this feature increases linear range
of the device up to 350 μA increasing nominal supply
current from 92 mA to 98 mA
10
Off_adj
DC offset control. Voltage at this pad sets output DC
offset. When it is floating DC offset is at 0V.
11
OUTP
Non-inverted data output with 50Ω back termination.
12
OUTN
Inverted data output with 50Ω back termination.
14
RSSI
Received signal strength indicator. This pin provides
a voltage proportional to the DC input current. This
voltage should be monitored during assembly to
optimally align the PD in the optical environment.
TRANSIMPEDANCE AMPLIFIERS - CHIP
5
5-8
Interface Schematic
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC690
v04.0709
10 Gbps TRANSIMPEDANCE
AMPLIFIER
Pad Descriptions (Continued)
Pad Number
Function
16
CL2
17
CL1
Description
Interface Schematic
Connect a capacitor to ground to increase the on-chip
DC-cancellation loop time constant.
0.1 μF is recommended.
Application Circuit
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
TRANSIMPEDANCE AMPLIFIERS - CHIP
5
5-9
HMC690
v04.0709
10 Gbps TRANSIMPEDANCE
AMPLIFIER
Assembly Diagram
TRANSIMPEDANCE AMPLIFIERS - CHIP
5
5 - 10
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC690
v04.0709
10 Gbps TRANSIMPEDANCE
AMPLIFIER
Mounting & Bonding Techniques for Millimeterwave MMICs
50 Ohm Microstrip transmission lines on 0.25mm (10 mil) thick alumina
thin film substrates are recommended for bringing RF to and from the chip
(Figure 1).
Microstrip substrates should be placed as close to the die as possible in
order to minimize bond wire length. Typical die-to-substrate spacing is
0.076mm to 0.152 mm (3 to 6 mils).
0.18mm (0.007”) Thick MMIC
Ribbon Bond
0.076mm
(0.003”)
RF Ground Plane
Handling Precautions
Follow these precautions to avoid permanent damage.
Storage: All bare die are placed in either Waffle or Gel based ESD protective containers, and then sealed in an ESD protective bag for shipment.
Once the sealed ESD protective bag has been opened, all die should be
stored in a dry nitrogen environment.
0.25mm (0.010”) Thick Alumina
Thin Film Substrate
Figure 1.
Cleanliness: Handle the chips in a clean environment. DO NOT attempt to clean the chip using liquid cleaning systems.
Static Sensitivity: Follow ESD precautions to protect against ESD strikes.
Transients: Suppress instrument and bias supply transients while bias is applied. Use shielded signal and bias
cables to minimize inductive pick-up.
General Handling: Handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers.
Mounting
The chip is not back-metallized and should be die mounted with epoxy. The mounting surface should be clean and
flat.
Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed
around the perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule.
Wire Bonding
RF bonds made with two 1 mil wires are recommended. These bonds should be thermosonically bonded with a force
of 40-60 grams. DC bonds of 0.001” (0.025 mm) diameter, thermosonically bonded, are recommended. Ball bonds
should be made with a force of 40-50 grams and wedge bonds at 18-22 grams. All bonds should be made with a
nominal stage temperature of 150 °C. A minimum amount of ultrasonic energy should be applied to achieve reliable
bonds. All bonds should be as short as possible, less than 12 mils (0.31 mm).
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5
TRANSIMPEDANCE AMPLIFIERS - CHIP
The die should be attached directly to the ground plane with epoxy (see
HMC general Handling, Mounting, Bonding Note).
5 - 11