Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP) X7R Dielectric, 6.3 – 250 VDC (Automotive Grade) Overview KEMET’s Automotive Grade Flexible Termination (FT-CAP) multilayer ceramic capacitor in X7R dielectric incorporates a unique, flexible termination system that is integrated with KEMET’s standard termination materials. A conductive silver epoxy is utilized between the base metal and nickel barrier layers of KEMET’s standard termination system in order to establish pliability while maintaining terminal strength, solderability and electrical performance. This technology was developed in order to address the primary failure mode of MLCCs– flex cracks, which are typically the result of excessive tensile and shear stresses produced during board flexure and thermal cycling. Flexible termination technology inhibits the transfer of board stress to the rigid ceramic body, therefore mitigating flex cracks which can result in low IR or short circuit failures. Combined with the stability of an X7R dielectric and designed to accommodate all capacitance requirements, these flex-robust devices are RoHS-compliant, offer up to 5mm of flex-bend capability and exhibit a predictable change in capacitance with respect to time and voltage. Capacitance change with reference to ambient temperature is limited to ±15% from −55°C to +125°C. Whether under-hood or in-cabin, these capacitors are designed to provide reliable performance in mission and safety critical automotive circuits. Stricter testing protocol and inspection criteria have been established for automotive grade products in recognition of potentially harsh environmental conditions. KEMET automotive grade series capacitors meet the demanding Automotive Electronics Council's AEC-Q200 qualification requirements. Although this technology does not eliminate the potential for mechanical damage that may propagate during extreme environmental and handling conditions, it does provide superior flex performance over standard termination systems. FT-CAP complements KEMET’s Open Mode, Floating Electrode (FECAP), Floating Electrode with Flexible Termination (FF-CAP) and KEMET Power Solutions (KPS) product lines by providing a complete portfolio of flex mitigation solutions. Click image above for interactive 3D content Open PDF in Adobe Reader for full functionality Ordering Information C 1206 X Case Size Specification/ Ceramic (L" x W") Series 0603 0805 1206 1210 1808 1812 1825 2220 2225 1 X = Flexible Termination 106 K 4 Capacitance Code (pF) Capacitance Tolerance Rated Voltage (VDC) J = ±5% K = ±10% M = ±20% 9 = 6.3 8 = 10 4 = 16 3 = 25 5 = 50 1 = 100 2 = 200 A = 250 Two significant digits + number of zeros R A C AUTO Dielectric Failure Rate/ Design Termination Finish1 Packaging/Grade (C-Spec)2 R = X7R A = N/A C = 100% Matte Sn See "Packaging C-Spec Ordering Options Table" below Additional termination finish options may be available. Contact KEMET for details. One world. One KEMET © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1078_X7R_FT-CAP_AUTO_SMD • 2/29/2016 1 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Automotive Grade) Packaging C-Spec Ordering Options Table Packaging/Grade Ordering Code (C-Spec)3 Packaging Type1 7" Reel 13" Reel / Unmarked 7" Reel/Unmarked/2 mm pitch2 13" Reel/Unmarked/2 mm pitch2 AUTO AUTO7411 (EIA 0603 and smaller case sizes) AUTO7210 (EIA 0805 and larger case sizes) 3190 3191 Reeling tape options (Paper or Plastic) are dependent on capacitor case size (L" x W") and thickness dimension. See "Chip Thickness/Tape & Reel Packaging Quantities" and "Tape & Reel Packaging Information". 2 The 2 mm pitch option allows for double the packaging quantity of capacitors on a given reel size. This option is limited to EIA 0603 (1608 metric) case size devices. For more information regarding 2 mm pitch option see "Tape & Reel Packaging Information". 3 All Automotive packaging C-Specs listed exclude the option to laser mark components. Please contact KEMET if you require a laser marked option. For more information see "Capacitor Marking". 3 For additional Information regarding "AUTO" C-Spec options, see "Automotive C-Spec Information". 1 Benefits • • • • • • AEC-Q200 automotive qualified −55°C to +125°C operating temperature range Superior flex performance (up to 5 mm) High capacitance flex mitigation Lead (Pb)-Free, RoHS and REACH compliant EIA 0603, 0805, 1206, 1210, 1808, 1812, 1825, 2220, and 2225 case sizes • DC voltage ratings of 6.3 V, 10 V, 16 V, 25 V, 50 V, 100 V, 200 V, and 250 V • Capacitance offerings ranging from 180 pF to 22 μF • Available capacitance tolerances of ±5%, ±10%, and ±20% • Non-polar device, minimizing installation concerns • 100% pure matte tin-plated termination finish allowing for excellent solderability Applications Typical applications include circuits with a direct battery or power source connection, critical and safety relevant circuits without (integrated) current limitation and any application that is subject to high levels of board flexure or temperature cycling. Examples include raw power input side filtering (power plane/bus), high current applications (automobile battery line) and circuits that cannot be fused to open. Markets include consumer, medical, industrial (power supply), automotive, aerospace and telecom. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1078_X7R_FT-CAP_AUTO_SMD • 2/29/2016 2 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Automotive Grade) Automotive C-Spec Information KEMET Automotive Grade products meet or exceed the requirements outlined by the Automotive Electronics Council. Details regarding test methods and conditions are referenced in document AEC–Q200, Stress Test Qualification for Passive Components. These products are supported by a Product Change Notification (PCN) and Production Part Approval Process warrant (PPAP). Automotive products offered through our distribution channel have been assigned an inclusive ordering code C-Spec, "AUTO". This C-Spec was developed in order to better serve small and medium sized companies that prefer an automotive grade component without the requirement to submit a customer Source Controlled Drawing (SCD) or specification for review by a KEMET engineering specialist. This C-Spec is therefore not intended for use by KEMET’s OEM Automotive customers and are not granted the same “privileges” as other automotive C-Specs. Customer PCN approval and PPAP request levels are limited (see details below). Product Change Notification (PCN) The KEMET Product Change Notification system is used to communicate primarily the following types of changes: • Product/process changes that affect product form, fit , function, and /or reliability • Changes in manufacturing site • Product obsolescence Customer Notification due to: KEMET Automotive C-Spec 1 Process/Product change Obsolescence* Days prior to implementation KEMET assigned1 Yes (with approval and sign off) Yes 180 days Minimum AUTO Yes (without approval) Yes 90 days Minimum KEMET assigned C-Specs require the submittal of a customer SCD or customer specification for review. For additional information contact KEMET. Production Part Approval Process (PPAP) The purpose of the Production Part Approval Process is: • To ensure that supplier can meet the manufacturability and quality requirements for the purchased parts. • To provide the evidence that all customer engineering design record and specification requirements are properly understood and fulfilled by the manufacturing organization. • To demonstrate that the established manufacturing process has the potential to produce the part KEMET Automotive C-Spec 1 PPAP (Product Part Approval Process) Level 1 2 3 4 5 KEMET assigned1 ● ● ● ● ● AUTO ○ ○ KEMET assigned C-Specs require the submittal of a customer SCD or customer specification for review. For additional information contact KEMET. ● Part Number specific PPAP available ○ Product family PPAP only © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1078_X7R_FT-CAP_AUTO_SMD • 2/29/2016 3 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Automotive Grade) Dimensions – Millimeters (Inches) L W B T S EIA Size Code Metric Size Code B Bandwidth S Separation Minimum 0603 1608 1.60 (.063) ± 0.17 (.007) 0.80 (.032) ± 0.15 (.006) 0.45 (.018) ± 0.15 (.006) 0.58 (.023) 0805 2012 2.00 (.079) ± 0.30 (.012) 1.25 (.049) ± 0.30 (.012) 0.50 (0.02) ± 0.25 (.010) 0.75 (.030) 1206 3216 3.30 (.130) ± 0.40 (.016) 1.60 (.063) ± 0.35 (.013) 0.60 (.024) ± 0.25 (.010) 1210 3225 3.30 (.130) ± 0.40 (.016) 2.60 (.102) ± 0.30 (.012) 0.60 (.024) ± 0.25 (.010) 1808 4520 4.70 (.185) ± 0.50 (.020) 2.00 (.079) ± 0.20 (.008) 1812 4532 4.50 (.178) ± 0.40 (.016) 3.20 (.126) ± 0.30 (.012) 0.70 (.028) ± 0.35 (.014) 1825 4564 4.60 (.181) ± 0.40 (.016) 6.40 (.252) ± 0.40 (.016) 0.70 (.028) ± 0.35 (.014) 2220 5650 5.90 (.232) ± 0.75 (.030) 5.00 (.197) ± 0.40 (.016) 0.70 (.028) ± 0.35 (.014) 2225 5664 5.90 (.232) ± 0.75 (.030) 6.40 (.248) ± 0.40 (.016) 0.70 (.028) ± 0.35 (.014) L Length W Width T Thickness See Table 2 for Thickness Mounting Technique Solder Wave or Solder Reflow 0.70 (.028) ± 0.35 (.014) N/A Solder Reflow Only Qualification/Certification Automotive grade products meet or exceed the requirements outlined by the Automotive Electronics Council. Details regarding test methods and conditions are referenced in document AEC-Q200, Stress Test Qualification for Passive Components. For additional information regarding the Automotive Electronics Council and AEC-Q200, please visit their website at www.aecouncil.com. Environmental Compliance Lead (Pb)-Free, RoHS, and REACH compliant without exemptions. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1078_X7R_FT-CAP_AUTO_SMD • 2/29/2016 4 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Automotive Grade) Electrical Parameters/Characteristics Item Parameters/Characteristics Operating Temperature Range −55°C to +125°C Capacitance Change with Reference to +25°C and 0 Vdc Applied (TCC) ±15% Aging Rate (Maximum % Capacitance Loss/Decade Hour) 3.0% 1 Dielectric Withstanding Voltage (DWV) 250% of rated voltage (5 ± 1 seconds and charge/discharge not exceeding 50mA) Dissipation Factor (DF) Maximum Limit @ 25°C 5%(6.3V & 10V), 3.5%(16V & 25V) and 2.5%(50V to 250V) 2 3 4 Insulation Resistance (IR) Minimum Limit @ 25°C See Insulation Resistance Limit Table (Rated voltage applied for 120 ± 5 secs @ 25°C) Regarding Aging Rate: Capacitance measurements (including tolerance) are indexed to a referee time of 1,000 hours. DWV is the voltage a capacitor can withstand (survive) for a short period of time. It exceeds the nominal and continuous working voltage of the capacitor. 3 Capacitance and dissipation factor (DF) measured under the following conditions: 1kHz ± 50Hz and 1.0 ± 0.2 Vrms if capacitance ≤10µF 120Hz ± 10Hz and 0.5 ± 0.1 Vrms if capacitance >10µF 4 To obtain IR limit, divide MΩ-µF value by the capacitance and compare to GΩ limit. Select the lower of the two limits. Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 & Agilent E4980 have a feature known as Automatic Level Control (ALC). The ALC feature should be switched to "ON". 1 2 Post Environmental Limits High Temperature Life, Biased Humidity, Moisture Resistance Dielectric Rated DC Voltage Capacitance Value > 25 X7R 16/25 < 16 Dissipation Factor (Maximum %) Capacitance Shift Insulation Resistance ±20% 10% of Initial Limit 3.0 All 5.0 7.5 © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1078_X7R_FT-CAP_AUTO_SMD • 2/29/2016 5 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Automotive Grade) Insulation Resistance Limit Table (X7R Dielectric) EIA Case Size 1,000 Megohm Microfarads or 100 GΩ 500 Megohm Microfarads or 10 GΩ 0201 N/A ALL 0402 < 0.012 µF ≥ 0.012 µF 0603 < 0.047 µF ≥ 0.047 µF 0805 < 0.15 µF ≥ 0.15 µF 1206 < 0.47 µF ≥ 0.47 µF 1210 < 0.39 µF ≥ 0.39 µF 1808 ALL N/A 1812 < 2.2 µF ≥ 2.2 µF 1825 ALL N/A 2220 < 10 µF ≥ 10 µF 2225 ALL N/A © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1078_X7R_FT-CAP_AUTO_SMD • 2/29/2016 6 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Automotive Grade) Table 1A – Capacitance Range/Selection Waterfall (0603 – 1210 Case Sizes) 1 2 250 5 FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FQ FQ FQ FA FZ FU FM FK FK 250 3 FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FQ FQ FQ FA FZ FU FM FK FK A 9 8 4 3 5 1 2 A 100 4 200 8 FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FQ FX FX FX FX FX FX FX FX FX FA FZ FL FM 100 9 FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FQ FQ FQ FQ FX FX FX FX FX FA FU FZ FZ FZ FZ FU FM FK FS 200 2 FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FQ FQ FQ FQ FX FX FX FX FX FA FU FU FU FU FJ FZ FM FZ FZ FU 25 1 A FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FQ FQ FQ FQ FX FX FX FX FX FA FU FU FU FU FJ FE FA FZ FQ FA 50 5 2 25 3 1 50 4 5 FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FQ FQ FQ FQ FX FX FX FX FX FA FU FU FU FU FJ FE FA FZ FQ FA 16 8 3 FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FQ FQ FQ FQ FX FX FX FX FX FA FU FU FU FU FJ FE FA FZ FQ FA 10 9 4 16 Voltage Code Case Size/ Series 8 10 Rated Voltage (VDC) 9 6.3 DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR 250 DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DS DS DS DG DG A 6.3 DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DD DD DD DD DD DD DS DS DS DS DS DG DG DG DG 2 250 DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DD DD DD DR DD DD DD DD DD DD DS DS DH DH 1 100 DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DD DD DD DR DR DR DR DR DD DD DG DD DG DG DG DG 5 C1210X 200 DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DD DD DD DR DR DR DR DR DD DD DG DD DD DD DD DD DS DG DG DG 25 DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DD DD DD DR DR DR DR DR DD DD DG DD DD DD DD DD DS DG DG DG 3 50 DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DD DD DD DR DR DR DR DR DD DD DG DD DD DD DD DD DS DG DG DG 4 16 CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ 8 10 CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ 50 CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ 16 CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ 25 CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ C0603X C0805X EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ ER ER ER ER EQ EQ EQ ER ES ET EF EF ES ES ES ES EN ES EF EF EH EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ ER ER ER ER EQ EQ EQ ER ES ET EF EF ES ES ES ES EN ES EF EF EH EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ ER ER ER ER EQ EQ EQ ER ES ET EF EF ES ES ES ES EN ES EF EF EH EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ ER ER ER ER EQ EQ EQ ER ES ET EF EU EU EU EF EF EH EH EH EH EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ ER ER ER ER ER ER ER ER ER ES ES ES EH EH EH EH EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ ER ER EQ EQ EQ EQ ER ER ER ER EM EU EU EU EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ ES ES ES ES EM EU EU EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ ES ES ES ES EM 6.3 10 16 25 50 100 200 Product Availability and Chip Thickness Codes – See Table 2 for Chip Thickness Dimensions 250 M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M 10 CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 9 6.3 250 A 200 200 2 50 100 1 100 5 16 3 25 4 CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ Cap Tolerance J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 6.3 100 200 8 10 25 50 9 6.3 2 100 1 200 5 25 3 50 4 16 8 10 Cap Cap Code 9 16 181 221 271 331 391 471 561 681 821 102 122 152 182 222 272 332 392 472 562 682 822 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334 394 474 564 684 824 105 125 155 185 225 275 335 395 475 565 Voltage Code Rated Voltage (VDC) C1206X 10 180 pF 220 pF 270 pF 330 pF 390 pF 470 pF 560 pF 680 pF 820 pF 1,000 pF 1,200 pF 1,500 pF 1,800 pF 2,200 pF 2,700 pF 3,300 pF 3,900 pF 4,700 pF 5,600 pF 6,800 pF 8,200 pF 10,000 pF 12,000 pF 15,000 pF 18,000 pF 22,000 pF 27,000 pF 33,000 pF 39,000 pF 47,000 pF 56,000 pF 68,000 pF 82,000 pF 0.10 µF 0.12 µF 0.15 µF 0.18 µF 0.22 µF 0.27 µF 0.33 µF 0.39 µF 0.47 µF 0.56 µF 0.68 µF 0.82 µF 1.0 µF 1.2 µF 1.5 µF 1.8 µF 2.2 µF 2.7 µF 3.3 µF 3.9 µF 4.7 µF 5.6 µF C0805X 6.3 Cap Code C0603X 6.3 Cap Case Size/ Series A 9 8 4 3 5 1 2 C1206X C1210X © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1078_X7R_FT-CAP_AUTO_SMD • 2/29/2016 7 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Automotive Grade) Table 1A – Capacitance Range/Selection Waterfall (0603 – 1210 Case Sizes) cont'd 3 5 1 2 A 25 100 250 4 250 8 200 9 100 A 200 2 50 16 1 16 10 5 10 6.3 3 6.3 4 250 8 100 9 200 A 25 2 50 1 250 10 5 200 6.3 3 50 100 200 4 100 8 16 9 25 2 C1210X EH EH EH EH EH EH EH EH EH 1 2 A FZ FZ FZ FM FU FU FU FK FU FU FU FS C0603X C0805X 1 2 A 9 8 4 C1206X 25 5 50 3 16 4 10 8 6.3 9 250 A 100 2 200 1 25 16 5 50 10 3 6.3 4 250 8 200 9 50 2 100 1 16 5 25 3 10 4 6.3 8 100 9 200 Voltage Code Case Size/ Series 25 16 FS FS Rated Voltage (VDC) 10 Cap Code 1 C1206X M M M M M M M 6.3 Cap K K K K K K K 5 C0805X Product Availability and Chip Thickness Codes – See Table 2 for Chip Thickness Dimensions Cap Tolerance J J J J J J J 3 25 4 50 8 50 685 825 106 126 156 186 226 9 16 6.8 µF 8.2 µF 10 µF 12 µF 15 µF 18 µF 22 µF Voltage Code Rated Voltage (VDC) 10 Cap Code C0603X 6.3 Cap Case Size/ Series 3 5 C1210X Table 1B – Capacitance Range/Selection Waterfall (1808 – 2225 Case Sizes) Case Size/ Series 1 2 A 3 5 1 2 A 5 1 2 A 250 25 50 100 200 250 50 100 200 250 2 5 200 1 A 100 50 5 2 50 25 Voltage Code C2225X 250 250 Rated Voltage (VDC) Product Availability and Chip Thickness Codes – See Table 2 for Chip Thickness Dimensions C1808X GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GE GG GG GG GG GG GJ 200 A 3 5 1 2 C1812X C1825X JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JD JF JF JC JC JC JC JC JC JC JC JC JC JD JD JF JF JC JC JC JC JC JC JC JC JC JC JD JD JF JF 100 200 250 2 KC KC KC KC KC KC KC KC KC KC KC KC KD KD KD KE KE KE 50 1 KC KC KC KC KC KC KC KC KC KC KC KC KD KD KD KE KE KE 250 5 KC KC KC KC KC KC KC KC KC KC KC KC KC KC KC KC KD KE 200 A KC KC KC KC KC KC KC KC KC KB KB KB KB KB KB KB KB KB 100 HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HD HD HD HD HF HF 50 HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HD HD HD HD HF HF 25 HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HD HD HF HF 250 HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB 200 GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GE GF GG GG GG GG GJ 100 GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GG GG GG GG GG GG GG GG 50 GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GC GC GE GE 250 GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GC GC GE GE 100 LD LD LD LD LD LD LD LD 50 M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M C2220X 200 200 LD LD LD LD LD LD LD LD LD LD LD LD LD LD K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 1 100 5 25 Cap Code 3 C1825X 250 Cap A LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD Cap Tolerance J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J C1812X 2 200 1 100 472 562 682 822 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334 394 474 564 684 824 105 125 5 100 4,700 pF 5,600 pF 6,800 pF 8,200 pF 10,000 pF 12,000 pF 15,000 pF 18,000 pF 22,000 pF 27,000 pF 33,000 pF 39,000 pF 47,000 pF 56,000 pF 68,000 pF 82,000 pF 0.10 µF 0.12 µF 0.15 µF 0.18 µF 0.22 µF 0.27 µF 0.33 µF 0.39 µF 0.47 µF 0.56 µF 0.68 µF 0.82 µF 1.0 µF 1.2 µF Voltage Code Rated Voltage (VDC) 50 Cap Code C1808X 50 Cap Case Size/ Series A 3 5 1 2 A 5 1 2 A C2220X C2225X © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1078_X7R_FT-CAP_AUTO_SMD • 2/29/2016 8 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Automotive Grade) Table 1B – Capacitance Range/Selection Waterfall (1808 – 2225 Case Sizes) cont'd A 3 5 1 2 A 5 1 2 A 3 5 1 2 A 5 1 2 A 50 100 200 250 50 100 200 250 25 50 100 200 250 50 100 200 250 M M M M M M M M M M M M M M M HC HD HF GK JC JD JF JC JD JF JF JO KC KD KD GK GK JO 200 250 25 50 100 200 250 50 100 200 250 25 50 100 200 250 50 100 200 250 JO Rated Voltage (VDC) 100 Cap Code 2 50 Cap K K K K K K K K K K K K K K K C2225X Product Availability and Chip Thickness Codes – See Table 2 for Chip Thickness Dimensions Cap Tolerance J J J J J J J J J J J J J J J C2220X 25 1 C1825X 250 155 185 225 275 335 395 475 565 685 825 106 126 156 186 226 5 C1812X 200 1.5 µF 1.8 µF 2.2 µF 2.7 µF 3.3 µF 3.9 µF 4.7 µF 5.6 µF 6.8 µF 8.2 µF 10 µF 12 µF 15 µF 18 µF 22 µF Voltage Code Rated Voltage (VDC) 100 Cap Code C1808X 50 Cap Case Size/ Series Voltage Code 5 1 2 A 3 5 1 2 A 5 1 2 A 3 5 1 2 A 5 1 2 A Case Size/ Series C1808X C1812X C1825X C2220X C2225X © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1078_X7R_FT-CAP_AUTO_SMD • 2/29/2016 9 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Automotive Grade) Table 2 – Chip Thickness/Tape & Reel Packaging Quantities Thickness Code Case Size1 Thickness ± Range (mm) CJ DR DD DS DG DH EQ ER EN ES ET EF EM EH EU FN FQ FX FE FA FZ FL FU FM FJ FK FS LD GB GC GE GF GG GK GJ HB HC HD HF JC JD JF JO KB KC KD KE 0603 0805 0805 0805 0805 0805 1206 1206 1206 1206 1206 1206 1206 1206 1206 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1808 1812 1812 1812 1812 1812 1812 1812 1825 1825 1825 1825 2220 2220 2220 2220 2225 2225 2225 2225 0.80 ± 0.15 0.78 ± 0.20 0.90 ± 0.10 1.00 ± 0.20 1.25 ± 0.15 1.25 ± 0.20 0.78 ± 0.20 0.90 ± 0.20 0.95 ± 0.10 1.00 ± 0.20 1.10 ± 0.20 1.20 ± 0.15 1.25 ± 0.15 1.60 ± 0.20 1.60 ± 0.25 0.78 ± 0.20 0.90 ± 0.20 0.95 ± 0.20 1.00 ± 0.10 1.10 ± 0.15 1.25 ± 0.20 1.40 ± 0.15 1.55 ± 0.20 1.70 ± 0.20 1.85 ± 0.20 2.10 ± 0.20 2.50 ± 0.30 0.90 ± 0.10 1.00 ± 0.10 1.10 ± 0.10 1.30 ± 0.10 1.50 ± 0.10 1.55 ± 0.10 1.60 ± 0.20 1.70 ± 0.15 1.10 ± 0.15 1.15 ± 0.15 1.30 ± 0.15 1.50 ± 0.15 1.10 ± 0.15 1.30 ± 0.15 1.50 ± 0.15 2.40 ± 0.15 1.00 ± 0.15 1.10 ± 0.15 1.30 ± 0.15 1.40 ± 0.15 Thickness Code Case Size1 Thickness ± Range (mm) Paper Quantity1 Plastic Quantity 7" Reel 13" Reel 7" Reel 13" Reel 7" Reel 13" Reel 7" Reel 13" Reel 4,000 0 0 0 0 0 4,000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 15,000 0 0 0 0 0 10,000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Paper Quantity1 0 4,000 4,000 2,500 2,500 2,500 4,000 4,000 4,000 2,500 2,500 2,500 2,500 2,000 2,000 4,000 4,000 4,000 2,500 2,500 2,500 2,000 2,000 2,000 2,000 2,000 1,000 2,500 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 500 1,000 1,000 1,000 1,000 0 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 8,000 8,000 10,000 10,000 10,000 10,000 10,000 10,000 8,000 8,000 8,000 8,000 8,000 4,000 10,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 2,000 4,000 4,000 4,000 4,000 Plastic Quantity Package quantity based on finished chip thickness specifications. 1 If ordering using the 2 mm Tape and Reel pitch option, the packaging quantity outlined in the table above will be doubled. This option is limited to EIA 0603 (1608 metric) case size devices. For more information regarding 2 mm pitch option see "Tape & Reel Packaging Information". © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1078_X7R_FT-CAP_AUTO_SMD • 2/29/2016 10 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Automotive Grade) Table 3 – Chip Capacitor Land Pattern Design Recommendations per IPC–7351 EIA Size Code Metric Size Code 0603 Density Level A: Maximum (Most) Land Protrusion (mm) Density Level B: Median (Nominal) Land Protrusion (mm) Density Level C: Minimum (Least) Land Protrusion (mm) C Y X V1 V2 C Y X V1 V2 C Y X V1 V2 1608 0.85 1.25 1.10 4.00 2.10 0.75 1.05 1.00 3.10 1.50 0.65 0.85 0.90 2.40 1.20 0805 2012 0.99 1.44 1.66 4.47 2.71 0.89 1.24 1.56 3.57 2.11 0.79 1.04 1.46 2.42 1.81 1206 3216 1.59 1.62 2.06 5.85 3.06 1.49 1.42 1.96 4.95 2.46 1.39 1.22 1.86 4.25 2.16 1210 3225 1.59 1.62 3.01 5.90 4.01 1.49 1.42 2.91 4.95 3.41 1.39 1.22 2.81 4.25 3.11 1808 4520 2.30 1.75 2.30 7.40 3.30 2.20 1.55 2.20 6.50 2.70 2.10 1.35 2.10 5.80 2.40 1812 4532 2.10 1.80 3.60 7.00 4.60 2.00 1.60 3.50 6.10 4.00 1.90 1.40 3.40 5.40 3.70 1825 4564 2.15 1.80 6.90 7.10 7.90 2.05 1.60 6.80 6.20 7.30 1.95 1.40 6.70 5.50 7.00 2220 5650 2.85 2.10 5.50 8.80 6.50 2.75 1.90 5.40 7.90 5.90 2.65 1.70 5.30 7.20 5.60 2225 5664 2.85 2.10 6.90 8.80 7.90 2.75 1.90 6.80 7.90 7.30 2.65 1.70 6.70 7.20 7.00 Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reflow solder processes. KEMET only recommends wave soldering of EIA 0603, 0805, and 1206 case sizes. Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reflow solder processes. Density Level C: For high component density product applications. Before adapting the minimum land pattern variations the user should perform qualification testing based on the conditions outlined in IPC Standard 7351 (IPC–7351). Image below based on Density Level B for an EIA 1210 case size. V1 Y Y X C V2 X C Grid Placement Courtyard © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1078_X7R_FT-CAP_AUTO_SMD • 2/29/2016 11 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Automotive Grade) Soldering Process Recommended Soldering Technique: • Solder wave or solder reflow for EIA case sizes 0603, 0805 and 1206 • All other EIA case sizes are limited to solder reflow only Recommended Reflow Soldering Profile: KEMET’s families of surface mount multilayer ceramic capacitors (SMD MLCCs) are compatible with wave (single or dual), convection, IR or vapor phase reflow techniques. Preheating of these components is recommended to avoid extreme thermal stress. KEMET’s recommended profile conditions for convection and IR reflow reflect the profile conditions of the IPC/J-STD-020 standard for moisture sensitivity testing. These devices can safely withstand a maximum of three reflow passes at these conditions. Termination Finish Preheat/Soak Temperature Minimum (TSmin) Temperature Maximum (TSmax) Time (tS) from TSmin to TSmax Ramp-Up Rate (TL to TP) SnPb 100% Matte Sn 100°C 150°C 60 – 120 seconds 150°C 200°C 60 – 120 seconds 183°C 217°C Time Above Liquidous (tL) 60 – 150 seconds 60 – 150 seconds Peak Temperature (TP) 235°C 260°C Time Within 5°C of Maximum Peak Temperature (tP) 20 seconds maximum 30 seconds maximum Time 25°C to Peak Temperature TL tP Maximum Ramp Up Rate = 3°C/sec Maximum Ramp Down Rate = 6°C/sec tL Tsmax Tsmin tS 3°C/second maximum 3°C/second maximum Liquidous Temperature (TL) Ramp-Down Rate (TP to TL) TP Temperature Profile Feature 25 25° C to Peak Time 6°C/second maximum 6°C/second maximum 6 minutes maximum 8 minutes maximum Note 1: All temperatures refer to the center of the package, measured on the capacitor body surface that is facing up during assembly reflow. Storage and Handling Ceramic chip capacitors should be stored in normal working environments. While the chips themselves are quite robust in other environments, solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres, and long term storage. In addition, packaging materials will be degraded by high temperature– reels may soften or warp and tape peel force may increase. KEMET recommends that maximum storage temperature not exceed 40ºC and maximum storage humidity not exceed 70% relative humidity. Temperature fluctuations should be minimized to avoid condensation on the parts and atmospheres should be free of chlorine and sulfur bearing compounds. For optimized solderability chip stock should be used promptly, preferably within 1.5 years of receipt. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1078_X7R_FT-CAP_AUTO_SMD • 2/29/2016 12 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Automotive Grade) Construction Detailed Cross Section Dielectric Material (BaTiO3) End Termination/ External Electrode (Cu) Epoxy Layer (Ag) Dielectric Material (BaTiO3) Barrier Layer (Ni) Termination Finish (100% Matte Sn) Inner Electrodes (Ni) End Termination/ External Electrode (Cu) Epoxy Layer (Ag) Barrier Layer (Ni) Inner Electrodes (Ni) Termination Finish (100% Matte Sn) © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1078_X7R_FT-CAP_AUTO_SMD • 2/29/2016 13 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Automotive Grade) Capacitor Marking (Optional): These surface mount multilayer ceramic capacitors are normally supplied unmarked. If required, they can be marked as an extra cost option. Marking is available on most KEMET devices but must be requested using the correct ordering code identifier(s). If this option is requested, two sides of the ceramic body will be laser marked with a “K” to identify KEMET, followed by two characters (per EIA–198 - see table below) to identify the capacitance value. EIA 0603 case size devices are limited to the “K” character only. Laser marking option is not available on: • C0G, Ultra Stable X8R and Y5V dielectric devices • EIA 0402 case size devices • EIA 0603 case size devices with Flexible Termination option. • KPS Commercial and Automotive Grade stacked devices. • X7R dielectric products in capacitance values outlined below EIA Case Size Metric Size Code Capacitance 0603 0805 1206 1210 1808 1812 1825 2220 2225 1608 2012 3216 3225 4520 4532 4564 5650 5664 ≤ 170 pF ≤ 150 pF ≤ 910 pF ≤ 2,000 pF ≤ 3,900 pF ≤ 6,700 pF ≤ 0.018 µF ≤ 0.027 µF ≤ 0.033 µF Marking appears in legible contrast. Illustrated below is an example of an MLCC with laser marking of “KA8”, which designates a KEMET device with rated capacitance of 100 µF. Orientation of marking is vendor optional. KEMET ID 2-Digit Capacitance Code © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1078_X7R_FT-CAP_AUTO_SMD • 2/29/2016 14 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Automotive Grade) Capacitor Marking (Optional) cont’d Alpha Character 9 A Capacitance (pF) For Various Alpha/Numeral Identifiers Numeral 0 1 2 3 4 0.1 10 10 100 1,000 10,000 B 0.11 1.1 11 110 1,100 11,000 C 0.12 12 12 120 1,200 12,000 D 0.13 13 13 130 1,300 E 0.15 15 15 150 1,500 5 6 7 8 100,000 1,000,000 10,000,000 100,000,000 110,000 1,100,000 11,000,000 110,000,000 120,000 1,200,000 12,000,000 120,000,000 13,000 130,000 1,300,000 13,000,000 130,000,000 15,000 150,000 1,500,000 15,000,000 150,000,000 160,000,000 Capacitance (pF) F 0.16 16 16 160 1,600 16,000 160,000 1,600,000 16,000,000 G 0.18 18 18 180 1,800 18,000 180,000 1,800,000 18,000,000 180,000,000 H 0.2 20 20 200 2,000 20,000 200,000 2,000,000 20,000,000 200,000,000 J 0.22 22 22 220 2,200 22,000 220,000 2,200,000 22,000,000 220,000,000 K 0.24 2.4 24 240 2,400 24,000 240,000 2,400,000 24,000,000 240,000,000 L 0.27 2.7 27 270 2,700 27,000 270,000 2,700,000 27,000,000 270,000,000 M 0.3 30 30 300 3,000 30,000 300,000 3,000,000 30,000,000 300,000,000 N 0.33 33 33 330 3,300 33,000 330,000 3,300,000 33,000,000 330,000,000 P 0.36 36 36 360 3,600 36,000 360,000 3,600,000 36,000,000 360,000,000 Q 0.39 39 39 390 3,900 39,000 390,000 3,900,000 39,000,000 390,000,000 R 0.43 43 43 430 4,300 43,000 430,000 4,300,000 43,000,000 430,000,000 S 0.47 4.7 47 470 4,700 47,000 470,000 4,700,000 47,000,000 470,000,000 T 0.51 5.1 51 510 5,100 51,000 510,000 5,100,000 51,000,000 510,000,000 U 0.56 56 56 560 5,600 56,000 560,000 5,600,000 56,000,000 560,000,000 V 0.62 62 62 620 6,200 62,000 620,000 6,200,000 62,000,000 620,000,000 W 0.68 68 68 680 6,800 68,000 680,000 6,800,000 68,000,000 680,000,000 X 0.75 75 75 750 7,500 75,000 750,000 7,500,000 75,000,000 750,000,000 Y 0.82 82 82 820 8,200 82,000 820,000 8,200,000 82,000,000 820,000,000 Z 0.91 9.1 91 910 9,100 91,000 910,000 9,100,000 91,000,000 910,000,000 a 0.25 25 25 250 2,500 25,000 250,000 2,500,000 25,000,000 250,000,000 b 0.35 35 35 350 3,500 35,000 350,000 3,500,000 35,000,000 350,000,000 d 0.4 40 40 400 4,000 40,000 400,000 4,000,000 40,000,000 400,000,000 e 0.45 45 45 450 4,500 45,000 450,000 4,500,000 45,000,000 450,000,000 f 0.5 50 50 500 5,000 50,000 500,000 5,000,000 50,000,000 500,000,000 m 0.6 60 60 600 6,000 60,000 600,000 6,000,000 60,000,000 600,000,000 n 0.7 70 70 700 7,000 70,000 700,000 7,000,000 70,000,000 700,000,000 t 0.8 80 80 800 8,000 80,000 800,000 8,000,000 80,000,000 800,000,000 y 0.9 90 90 900 9,000 90,000 900,000 9,000,000 90,000,000 900,000,000 © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1078_X7R_FT-CAP_AUTO_SMD • 2/29/2016 15 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Automotive Grade) Tape & Reel Packaging Information KEMET offers multilayer ceramic chip capacitors packaged in 8, 12 and 16 mm tape on 7" and 13" reels in accordance with EIA Standard 481. This packaging system is compatible with all tape-fed automatic pick and place systems. See Table 2 for details on reeling quantities for commercial chips. Bar Code Label Anti-Static Reel ® Embossed Plastic* or Punched Paper Carrier. ET KEM Chip and KPS Orientation in Pocket (except 1825 Commercial, and 1825 and 2225 Military) Sprocket Holes Embossment or Punched Cavity 8 mm, 12 mm or 16 mm Carrier Tape 178 mm (7.00") or 330 mm (13.00") Anti-Static Cover Tape (.10 mm (.004") Maximum Thickness) *EIA 01005, 0201, 0402 and 0603 case sizes available on punched paper carrier only. Table 5 – Carrier Tape Configuration, Embossed Plastic & Punched Paper (mm) EIA Case Size Tape Size (W)* Embossed Plastic 7" Reel 13" Reel Punched Paper 7" Reel Pitch (P1)* 13" Reel Pitch (P1)* 01005 – 0402 8 2 2 0603 8 2/4 2/4 0805 8 4 4 4 4 1206 – 1210 8 4 4 4 4 1805 – 1808 12 4 4 ≥ 1812 12 8 8 KPS 1210 12 8 8 KPS 1812 & 2220 16 12 12 Array 0508 & 0612 8 4 4 *Refer to Figures 1 & 2 for W and P1 carrier tape reference locations. *Refer to Tables 6 & 7 for tolerance specifications. New 2 mm Pitch Reel Options* Packaging Ordering Code (C-Spec) C-3190 C-3191 C-7081 C-7082 Packaging Type/Options Automotive grade 7" reel unmarked Automotive grade 13" reel unmarked Commercial grade 7" reel unmarked Commercial grade 13" reel unmarked * 2 mm pitch reel only available for 0603 EIA case size. 2 mm pitch reel for 0805 EIA case size under development. Benefits of Changing from 4 mm to 2 mm Pitching Spacing • Lower placement costs • Double the parts on each reel results in fewer reel changes and increased efficiency • Fewer reels result in lower packaging, shipping and storage costs, reducing waste © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1078_X7R_FT-CAP_AUTO_SMD • 2/29/2016 16 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Automotive Grade) Figure 1 – Embossed (Plastic) Carrier Tape Dimensions P2 T T2 ØDo [10 pitches cumulative tolerance on tape ± 0.2 mm] Po E1 Ao F Ko B1 E2 Bo S1 W P1 T1 Center Lines of Cavity ØD 1 Cover Tape B 1 is for tape feeder reference only, including draft concentric about B o. Embossment For cavity size, see Note 1 Table 4 User Direction of Unreeling Table 6 – Embossed (Plastic) Carrier Tape Dimensions Metric will govern Constant Dimensions — Millimeters (Inches) Tape Size D0 8 mm 12 mm 1.5 +0.10/-0.0 (0.059 +0.004/-0.0) 16 mm D1 Minimum Note 1 1.0 (0.039) 1.5 (0.059) E1 P0 1.75 ±0.10 (0.069 ±0.004) 4.0 ±0.10 (0.157 ±0.004) R Reference S1 Minimum Note 2 Note 3 25.0 (0.984) 2.0 ±0.05 0.600 (0.079 ±0.002) (0.024) 30 (1.181) P2 T Maximum T1 Maximum 0.600 (0.024) 0.100 (0.004) Variable Dimensions — Millimeters (Inches) Tape Size Pitch 8 mm Single (4 mm) 12 mm Single (4 mm) & Double (8 mm) 16 mm Triple (12 mm) B1 Maximum Note 4 4.35 (0.171) 8.2 (0.323) 12.1 (0.476) E2 Minimum 6.25 (0.246) 10.25 (0.404) 14.25 (0.561) F P1 3.5 ±0.05 (0.138 ±0.002) 5.5 ±0.05 (0.217 ±0.002) 7.5 ±0.05 (0.138 ±0.002) 4.0 ±0.10 (0.157 ±0.004) 8.0 ±0.10 (0.315 ±0.004) 12.0 ±0.10 (0.157 ±0.004) T2 Maximum 2.5 (0.098) 4.6 (0.181) 4.6 (0.181) W Maximum 8.3 (0.327) 12.3 (0.484) 16.3 (0.642) A0,B0 & K0 Note 5 1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and hole location shall be applied independent of each other. 2. The tape with or without components shall pass around R without damage (see Figure 6). 3. If S1 < 1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Standard 481 paragraph 4.3 section b). 4. B1 dimension is a reference dimension for tape feeder clearance only. 5. The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that: (a) the component does not protrude above the top surface of the carrier tape. (b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed. (c) rotation of the component is limited to 20° maximum for 8 and 12 mm tapes and 10° maximum for 16 mm tapes (see Figure 3). (d) lateral movement of the component is restricted to 0.5 mm maximum for 8 and 12 mm wide tape and to 1.0 mm maximum for 16 mm tape (see Figure 4). (e) for KPS Series product, A0 and B0 are measured on a plane 0.3 mm above the bottom of the pocket. (f) see Addendum in EIA Standard 481 for standards relating to more precise taping requirements. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1078_X7R_FT-CAP_AUTO_SMD • 2/29/2016 17 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Automotive Grade) Figure 2 – Punched (Paper) Carrier Tape Dimensions P2 T Po ØDo [10 pitches cumulative tolerance on tape ± 0.2 mm] A0 F P1 T1 T1 Top Cover Tape W E2 B0 Bottom Cover Tape E1 G Cavity Size, See Note 1, Table 7 Center Lines of Cavity Bottom Cover Tape User Direction of Unreeling Table 7 – Punched (Paper) Carrier Tape Dimensions Metric will govern Constant Dimensions — Millimeters (Inches) Tape Size D0 E1 P0 P2 8 mm 1.5 +0.10 -0.0 (0.059 +0.004 -0.0) 1.75 ±0.10 (0.069 ±0.004) 4.0 ±0.10 (0.157 ±0.004) 2.0 ±0.05 (0.079 ±0.002) G Minimum 0.10 (0.004) Maximum R Reference Note 2 0.75 (0.030) 25 (0.984) T Maximum W Maximum A0 B 0 1.1 (0.098) 8.3 (0.327) 8.3 (0.327) T1 Maximum Variable Dimensions — Millimeters (Inches) Tape Size Pitch 8 mm Half (2 mm) 8 mm Single (4 mm) E2 Minimum 6.25 (0.246) F 3.5 ±0.05 (0.138 ±0.002) P1 2.0 ±0.05 (0.079 ±0.002) 4.0 ±0.10 (0.157 ±0.004) Note 1 1. The cavity defined by A0, B0 and T shall surround the component with sufficient clearance that: a) the component does not protrude beyond either surface of the carrier tape. b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed. c) rotation of the component is limited to 20° maximum (see Figure 3). d) lateral movement of the component is restricted to 0.5 mm maximum (see Figure 4). e) see Addendum in EIA Standard 481 for standards relating to more precise taping requirements. 2. The tape with or without components shall pass around R without damage (see Figure 6). © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1078_X7R_FT-CAP_AUTO_SMD • 2/29/2016 18 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Automotive Grade) Packaging Information Performance Notes 1. Cover Tape Break Force: 1.0 Kg minimum. 2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be: Tape Width Peel Strength 8 mm 0.1 to 1.0 Newton (10 to 100 gf) 12 and 16 mm 0.1 to 1.3 Newton (10 to 130 gf) The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165° to 180° from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 300 ±10 mm/minute. 3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA Standards 556 and 624. Figure 3 – Maximum Component Rotation ° T Maximum Component Rotation Top View Maximum Component Rotation Side View Typical Pocket Centerline Tape Width (mm) 8,12 16 – 200 Bo Maximum Rotation ( 20 10 ° T) Typical Component Centerline Ao Figure 4 – Maximum Lateral Movement 8 mm & 12 mm Tape 0.5 mm maximum 0.5 mm maximum 16 mm Tape ° s Tape Maximum Width (mm) Rotation ( 8,12 20 16 – 56 10 72 – 200 5 ° S) Figure 5 – Bending Radius Embossed Carrier Punched Carrier 1.0 mm maximum 1.0 mm maximum R Bending Radius R © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1078_X7R_FT-CAP_AUTO_SMD • 2/29/2016 19 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Automotive Grade) Figure 6 – Reel Dimensions Full Radius, See Note W3 (Includes Access Hole at Slot Location (Ø 40 mm minimum) flange distortion at outer edge) W2 (Measured at hub) D A (See Note) N C (Arbor hole diameter) B (see Note) W1 (Measured at hub) If present, tape slot in core for tape start: 2.5 mm minimum width x 10.0 mm minimum depth Note: Drive spokes optional; if used, dimensions B and D shall apply. Table 8 – Reel Dimensions Metric will govern Constant Dimensions — Millimeters (Inches) Tape Size A B Minimum C D Minimum 8 mm 178 ±0.20 (7.008 ±0.008) or 330 ±0.20 (13.000 ±0.008) 1.5 (0.059) 13.0 +0.5/-0.2 (0.521 +0.02/-0.008) 20.2 (0.795) 12 mm 16 mm Variable Dimensions — Millimeters (Inches) Tape Size N Minimum W1 W2 Maximum W3 50 (1.969) 8.4 +1.5/-0.0 (0.331 +0.059/-0.0) 12.4 +2.0/-0.0 (0.488 +0.078/-0.0) 16.4 +2.0/-0.0 (0.646 +0.078/-0.0) 14.4 (0.567) 18.4 (0.724) 22.4 (0.882) Shall accommodate tape width without interference 8 mm 12 mm 16 mm © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1078_X7R_FT-CAP_AUTO_SMD • 2/29/2016 20 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Automotive Grade) Figure 7 – Tape Leader & Trailer Dimensions Embossed Carrier Carrier Tape Punched Carrier 8 mm & 12 mm only END Round Sprocket Holes START Top Cover Tape Elongated Sprocket Holes (32 mm tape and wider) Trailer 160 mm Minimum Components 100 mm Minimum Leader 400 mm Minimum Top Cover Tape Figure 8 – Maximum Camber Elongated sprocket holes (32 mm & wider tapes) Carrier Tape Round Sprocket Holes 1 mm Maximum, either direction Straight Edge 250 mm © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1078_X7R_FT-CAP_AUTO_SMD • 2/29/2016 21 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Automotive Grade) KEMET Corporation World Headquarters Europe Asia Southern Europe Sasso Marconi, Italy Tel: 39-051-939111 Northeast Asia Hong Kong Tel: 852-2305-1168 Mailing Address: P.O. Box 5928 Greenville, SC 29606 Skopje, Macedonia Tel: 389-2-55-14-623 Shenzhen, China Tel: 86-755-2518-1306 www.kemet.com Tel: 864-963-6300 Fax: 864-963-6521 Central Europe Landsberg, Germany Tel: 49-8191-3350800 Corporate Offices Fort Lauderdale, FL Tel: 954-766-2800 Kamen, Germany Tel: 49-2307-438110 North America Northern Europe Wyboston, United Kingdom Tel: 44-1480-273082 Taipei, Taiwan Tel: 886-2-27528585 Espoo, Finland Tel: 358-9-5406-5000 Southeast Asia Singapore Tel: 65-6701-8033 2835 KEMET Way Simpsonville, SC 29681 Northeast Wilmington, MA Tel: 978-658-1663 Southeast Lake Mary, FL Tel: 407-855-8886 Central Novi, MI Tel: 248-994-1030 Beijing, China Tel: 86-10-5877-1075 Shanghai, China Tel: 86-21-6447-0707 Seoul, South Korea Tel: 82-2-6294-0550 Penang, Malaysia Tel: 60-4-6430200 Bangalore, India Tel: 91-806-53-76817 Irving, TX Tel: 972-915-6041 West Milpitas, CA Tel: 408-433-9950 Mexico Guadalajara, Jalisco Tel: 52-33-3123-2141 Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of KEMET Electronics Corporation. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1078_X7R_FT-CAP_AUTO_SMD • 2/29/2016 22 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Automotive Grade) Disclaimer All product specifications, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are not intended to constitute – and KEMET specifically disclaims – any warranty concerning suitability for a specific customer application or use. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not be required. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1078_X7R_FT-CAP_AUTO_SMD • 2/29/2016 23