Supplement: X-ray Tube Stator Compatibility Tables

CPI Canada Inc
X-Ray Tube Stator Compatibility Tables
SUPPLEMENT
X-RAY TUBE STATOR
COMPATIBILITY TABLES
CONTENTS:
1.0
2.0
3.0
3.1
INTRODUCTION ............................................................................................................................................. 2
LOW SPEED STARTER TUBE SELECT TABLE ............................................................................................ 2
DUAL SPEED STARTER TUBE SELECT TABLE......................................................................................... 18
DUAL SPEED STARTER (AND INDICO IQ LOW SPEED STARTER) TUBE CODES................................... 38
PROPRIETARY AND CONFIDENTIAL
The design and information contained in this document is proprietary to Communications & Power Industries
Canada Inc. (CPI), has been designed and developed at private expense, and is the exclusive property of CPI.
The information contained herein is loaned in confidence solely for the installation, operation, and maintenance of
CPI equipment. This document may not be duplicated in whole or in part, or be used for re-engineering, reverse
engineering, or otherwise reproducing in any form or creating or attempting to create or permitting, allowing or
assisting others to create or manufacture CPI’s product or products derived there from, without the express written
permission of CPI.
Copyright © by Communications & Power Industries Canada Inc. All rights reserved.
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 1
X-Ray Tube Stator Compatibility Tables
1.0
CPI Canada Inc
INTRODUCTION
This supplement contains the X-Ray Tube Stator Compatibility Tables for the Low Speed Starter (LSS)
and the Dual Speed Starter (DSS).
2.0
LOW SPEED STARTER TUBE SELECT TABLE
Indico IQ Generators Only
The Low Speed Starter (LSS) synthesizes its output frequencies independently of the line frequency and
will operate most tubes at 60 Hz, as indicated in Table 1.
Unless indicated otherwise within Table 1, setting the switches to the code indicated for the applicable
Tube Type selects all required operating parameters. The Low Speed Starter part number corresponds to
the configuration of phase-shift capacitors installed.
Reference notes are provided at the end of Table 1. Tube operating parameters for each switch code are
contained in Table 3 for reference.
Indico 100 Generators Only
The boost voltage may be set to either 240 VAC (factory default) or 120 VAC. This should be set to 240
VAC, except where specifically noted in Table 1 below. The Low Speed Starter output is at the same
frequency as the AC line (50 Hz or 60 Hz).
The Low Speed Starter is a separate sub-assembly within the Indico 100 Generator. The LSS part number
corresponds to the value of phase-shift capacitor incorporated within this sub-assembly. The boost time is
selectable to either 1.5 seconds or 2.5 seconds, and the run voltage is selectable to any of 52 VAC,
73 VAC or 94 VAC.
CMP200 Generators Only
The boost voltage may be set to either 240 VAC (factory default) or 120 VAC. This should be set to 240
VAC, except where specifically noted in Table 1 below. The Low Speed Starter output is at the same
frequency as the AC line (50 Hz or 60 Hz).
The Low Speed Starter is integrated into the HV Auxiliary Board within the CMP 200® and CMP 200® DR
generators. The phase-shift capacitor is chassis-mounted and may be changed in the field. The LSS part
number corresponds to the value of capacitor installed. The boost time is software-configurable from the
console or GenWare®. Note that these generators do not use a separate run voltage, instead cycling the
boost voltage on/off as required. The boost duty cycle is not hardware-configurable.
Mobile DR Generators Only
The Low Speed Starter is a separate sub-assembly within Mobile DR generator configurations. The boost
voltage is 240 VAC at 60 Hz, boost time is 1.5 seconds, and provides a 30µF phase-shift capacitor.
Use and disclosure is subject to the restrictions on the title page of this CPI document.
Page 2
Rev. AD
X-Ray Generator Service Manual Supplement
746026
CPI Canada Inc.
2.0
X-Ray Tube Stator Compatibility Tables
LOW SPEED STARTER TUBE SELECT TABLE (cont)
TABLE 1: TUBE TYPES (LOW SPEED STARTER)
INDICO IQ only
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
CODE,
INDICO
100 only
OUTPUT RUN
VOLTS
Switches
FREQ.
(1........5)
INDICO 100 /
CMP200/DR only
BOOST
VOLTS
INDICO IQ
(See note 1)
BOOST SHIFT
TIME
CAP.
LSS PART NO.
(See note 2)
INDICO 100
SHIFT
CAP.
LSS PART NO.
(See note 2)
CMP200 / CMP200 DR
SHIFT
CAP.
LSS PART NO.
(See note 2)
CGR (GE)
MN640
Statorix 200A/240/260 M641
MN641
(50/110  stator)
M643
CGR (GE)
RN620
RN621
Statorix 550
(50/110  stator)
Type 28 50 Hz
(00111)
94 VAC
240 VAC 2.5 sec
12.5F 905135-41
12.5F 732752-01
N/A
N/A
Type 28 50 Hz
(00111)
94 VAC
240 VAC 2.5 sec
12.5F 905135-41
12.5F 732752-01
N/A
N/A
Chirana
Rotax KA 125
Type 21 60 Hz
(10101)
73 VAC
240 VAC 1.5 sec
33 F
30 F
905135-41
905135-43
30 F
30 F
903836-00
73 VAC
240 VAC 1.5 sec
N/A
N/A
100F, 732752-04
52 mH
N/A
N/A
RIK-T 0.8/2.0 12/50
RIK-T 1.2/2.0 30/50
732752-00
(20/50  stator)
Chirana
Rotax KA 125
N/A
N/A
(20/20/20  stator)
Comet
DO7 / DX7
(25/50  stator)
Comet
DO9 / DX9
(20/50  stator)
DX7
DX71HS
(See note 3)
Type 0 60 Hz
(00000)
52 VAC
240 VAC 1.5 sec
33 F
30 F
905135-41
905135-43
30 F
732752-00
30 F
903836-00
DX9
DX91H / HS
DX92H / HS
DX93H / HS
DX94HS
DX96HS
DX97HS
Type 0 60 Hz
(00000)
52 VAC
240 VAC 1.5 sec
33 F
30 F
905135-41
905135-43
30 F
732752-00
30 F
903836-00
(See note 3)
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 3
CPI Canada Inc.
2.0
X-Ray Tube Stator Compatibility Tables
LOW SPEED STARTER TUBE SELECT TABLE (cont)
INDICO IQ only
INDICO
100 only
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
Comet
D010 / DX10
DX10H / HS
DX101H / HS
DX104HS
DX105HS
DX106HS
(See note 3)
DX700HS
(See note 3)
Type 0 60 Hz
(00000)
52 VAC
Type 1 60 Hz
(10000)
XSTAR8 (XST-8)
XSTAR74 (XST-74)
XSTAR-WHIS
(20/50  stator)
Comet
DO700 / DX700
CODE,
OUTPUT RUN
VOLTS
INDICO 100 /
CMP200/DR only
BOOST
TIME
INDICO 100
CMP200 / CMP200 DR
SHIFT LSS PART NO. SHIFT
CAP. (See note 2)
CAP.
LSS PART NO. SHIFT
(See note 2)
CAP.
240 VAC 1.5 sec
33 F
30 F
905135-41
905135-43
30 F
732752-00
30 F
903836-00
N/A
N/A
33 F
30 F
905135-41
905135-43
N/A
N/A
N/A
N/A
Type 0 60 Hz
(00000)
52 VAC
240 VAC 1.5 sec
33 F
30 F
905135-41
905135-43
30 F
732752-00
30 F
903836-00
DA1002 (DU304-1.0/2.0)
DA1029 (DU304-0.6/1.2)
DA1036 (DU404-0.6/1.2)
DA1083 (DU404-0.3/1.0)
DA1092 (DU604-0.6/1.2)
DA1094 (DU404-0.4/0.8)
Type 4 60 Hz
(00100)
52 VAC
240 VAC 2.5 sec
(Indico)
33 F
30 F
40 F
905135-41
905135-43
905135-44
45 F
(50 or
60 Hz)
732752-02
(prefer)
40 F
(50 or
60 Hz)
903836-01
(prefer)
30 F
(60 Hz
only)
732752-00
30 F
(60 Hz
only)
903836-00
DU 1750
DU 3050
DU 2550
DU 33100
(See note 6)
DU 1750
DU 3050
DU 2550
DU 33100
(See note 6)
Type 9 60 Hz
(10010)
52 VAC
240 VAC 1.5 sec
33 F
30 F
905135-41
905135-43
30 F
732752-00
30 F
903836-00
Type 9 60 Hz
(10010)
N/A
N/A
33 F
30 F
905135-41
905135-43
N/A
N/A
N/A
N/A
Switches
FREQ.
(1........5)
BOOST
VOLTS
INDICO IQ
(See note 1)
N/A
LSS PART NO.
(See note 2)
(25/50  stator)
Comet
XSTAR
(25/50  stator)
Dunlee (Philips)
DA10 series
(20/50  stator)
Dunlee (Philips)
DA90, DA90HS
(36/44  stator)
(See note 4)
Dunlee (Philips)
DA90, DA90HS
(9/11  stator)
(See note 5)
2.0 sec
(CMP200)
N/A
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 4
CPI Canada Inc.
2.0
X-Ray Tube Stator Compatibility Tables
LOW SPEED STARTER TUBE SELECT TABLE (cont)
INDICO IQ only
INDICO
100 only
INDICO 100 /
CMP200/DR only
INDICO IQ
(See note 1)
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
Dunlee (Philips)
DR1400 series
DR1429 (DU304-0.6/1.2)
DR1436 (DU404-0.6/1.2)
DR1492 (DU604-0.6/1.2)
DR1494 (DU404-0.4/0.8)
Type 4 60 Hz
(00100)
DR1817
DR1833
Type 9 60 Hz
(10010)
52 VAC
240 VAC 1.5 sec
33 F
30 F
DR1817
DR1833
Type 9 60 Hz
(10010)
N/A
N/A
PX1302 (DU303-1.0/2.0)
PX1312 (DU303-0.6/1.2)
PX1351 (DU143-1.0/2.0)
Type 7 60 Hz
(11100)
52 VAC
240 VAC 2.5 sec
(Indico)
(20/50  stator)
Dunlee (Philips)
DR1800 series
CODE,
OUTPUT RUN
VOLTS
Switches
FREQ.
(1........5)
52 VAC
BOOST
VOLTS
BOOST
TIME
240 VAC 2.5 sec
(Indico)
2.0 sec
(CMP200)
INDICO 100
CMP200 / CMP200 DR
SHIFT LSS PART NO. SHIFT
CAP. (See note 2)
CAP.
LSS PART NO. SHIFT
(See note 2)
CAP.
33 F
30 F
40 F
45 F
(50 or
60 Hz)
732752-02
(prefer)
40 F
(50 or
60 Hz)
903836-01
(prefer)
30 F
(60 Hz
only)
732752-00
30 F
(60 Hz
only)
903836-00
905135-41
905135-43
30 F
732752-00
30 F
903836-00
33 F
30 F
905135-41
905135-43
N/A
N/A
N/A
N/A
33 F
30 F
905135-41
905135-43
30 F
732752-00
30 F
903836-00
905135-41
905135-43
905135-44
LSS PART NO.
(See note 2)
(19/22  stator)
(See note 4)
Dunlee (Philips)
DR1800 series
N/A
(9/11  stator)
(See note 5)
Dunlee
(Picker / Philips)
PX1300 series
(3” anode)
“S” stator
(15/30 )
2.0 sec
(CMP200)
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 5
CPI Canada Inc.
2.0
X-Ray Tube Stator Compatibility Tables
LOW SPEED STARTER TUBE SELECT TABLE (cont)
INDICO IQ only
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
Dunlee
(Picker / Philips)
PX1400 series
CODE,
INDICO
100 only
OUTPUT RUN
VOLTS
Switches
FREQ.
(1........5)
PX1402 (DU304-1.0/2.0)
PX1412 (DU304-0.6/1.2)
PX1415 (DU404-0.3/0.9)
PX1425
(4” anode)
PX1429 (DU304-0.6/1.2)
“S” stator
PX1431 (DU304-0.7/1.4)
(15/30 )
PX1436 (DU404-0.6/1.2)
PX1456 (DU404-0.3/1.0)
PX1463 (DU604-0.6/1.2)
PX1472 (DU604-0.3/1.0)
PX1473 (DU404-0.6/1.2)
PX1475 (DU754-0.6/1.2)
PX1482 (DU404-0.6/1.0)
PX1483 (DU404-0.3/1.0)
PX1492 (DU604-0.6/1.2)
PX1494 (DU404-0.4/0.8)
Eureka (see Varian)
Type 1 60 Hz
(10000)
GE Maxiray 75
(3” anode)
(23/23  equal
impedance “E”
stator)
Type 14 60 Hz
(01110)
73 VAC
Type 20 60 Hz
(00101)
73 VAC
* Dunlee tube
GE Maxiray 100
(4” anode)
(23/23  equal
impedance “E”
stator)
MX-75
52 VAC
INDICO 100 /
CMP200/DR only
BOOST
VOLTS
INDICO IQ
(See note 1)
BOOST SHIFT
TIME
CAP.
INDICO 100
LSS PART NO. SHIFT
(See note 2)
CAP.
CMP200 / CMP200 DR
LSS PART NO. SHIFT
(See note 2)
CAP.
LSS PART NO.
(See note 2)
33 F
30 F
905135-41
905135-43
30 F
732752-00
30 F
903836-00
240 VAC 1.5 sec
45 F
40 F
905135-41
905135-44
45 F
732752-02
40 F
903836-01
240 VAC 1.5 sec
45 F
40 F
905135-41
905135-44
45 F
732752-02
40 F
903836-01
240 VAC 2.5 sec
(Indico
2.0 sec
(CMP200)
DU303 (1.0/2.0) *
DU303 (0.6/1.2) *
MX-100
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 6
CPI Canada Inc.
X-Ray Tube Stator Compatibility Tables
INDICO IQ only
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
CODE,
INDICO
100 only
OUTPUT RUN
VOLTS
Switches
FREQ.
(1........5)
INDICO 100 /
CMP200/DR only
BOOST
VOLTS
INDICO IQ
(See note 1)
BOOST SHIFT
TIME
CAP.
INDICO 100
LSS PART NO. SHIFT
(See note 2)
CAP.
CMP200 / CMP200 DR
LSS PART NO. SHIFT
(See note 2)
CAP.
Gilardoni
Rotagil S/AS
AR11-30
AR20-50
AR30-00-1
AR30-60
AR30-100
AR40-100
AR9000-1
AR9000-2
Hangzhou Kailong (see Kailong RADII)
Type 22 50 Hz
(01101)
52 VAC
240 VAC 1.5 sec
33 F
30 F
905135-41
905135-43
30 F
Hangzhou Wandong WANRAY
(Polygala / Yuan Zhi)
XD51-20.40/125 (LQ16-XA2)
XD51-10.40/125 (LQ16-XA4)
XD52-30.50/125 (LQ17-XB1)
XD57-20.50/150 (LQ16-XD57)
IAE
RTM 70H
X20P
C30, C31
X22
(28/57.5  stator)
X40
(25/62  stator)
X76
Type 0 60 Hz
(00000)
52 VAC
240 VAC 1.5 sec
33 F
30 F
905135-41
905135-43
45 F 732752-02
(50 Hz)
40 F
903836-01
(50 Hz)
Type 10 50 Hz
(01010)
52 VAC
240 VAC 1.5 sec
33 F
30 F
905135-41
905135-43
30 F
30 F
732752-00
732752-00
30 F
LSS PART NO.
(See note 2)
903836-00
903836-00
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 7
CPI Canada Inc.
2.0
X-Ray Tube Stator Compatibility Tables
LOW SPEED STARTER TUBE SELECT TABLE (cont)
INDICO IQ only
INDICO
100 only
INDICO 100 /
CMP200/DR only
INDICO IQ
(See note 1)
INDICO 100
CMP200 / CMP200 DR
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
IAE
C40
(28/57.5  stator)
(33/64  stator)
X39
X40
X42
X76
Type 19 60 Hz
(11001)
52 VAC
240 VAC 1.5 sec
25 F
20 F
905135-41
905135-42
30 F
732752-00
20 F
903836-02
IAE
C52, C52 Super
C100
C352
(20/40  stator)
RTC 600HS
RTC 700HS
RTC 1000HS
RTM 78H / HS
RTM 90H / HS
RTM 92H / HS
RTM 101H / HS
RTM 102H / HS
RTM 780H / HS
RTM 782H / HS
X39
X40
X50H X50AH
KL64
KL65
KL66
Type 27 50 Hz
(11011)
52 VAC
240 VAC 1.5 sec
33 F
30 F
905135-41
905135-43
30 F
732752-00
(prefer)
30 F
903836-00
(prefer)
45 F
732752-02
40 F
903836-01
Type 0 60 Hz
(00000)
52 VAC
240 VAC 1.5 sec
33 F
30 F
905135-41
905135-43
30 F
732752-00
30 F
903836-00
KL74
KL80
KL80A
KL86
Type 0 60 Hz
(00000)
52 VAC
240 VAC 1.5 sec
33 F
30 F
905135-41
905135-43
732752-00
(prefer)
Type 19 60 Hz
(11001)
30 F
(50 or
60 Hz)
40 F
(50 Hz
only)
20 F
903836-00
(prefer)
KL76
30 F
(50 or
60 Hz)
45 F
(50 Hz
only)
30 F
Kailong RADII
H1064
H1065
H1066
(25/62  stator)
Kailong RADII
H1074
H1080
H1086
CODE,
OUTPUT RUN
VOLTS
Switches
FREQ.
(1........5)
BOOST
VOLTS
BOOST SHIFT
TIME
CAP.
LSS PART NO. SHIFT
(See note 2)
CAP.
(20/50  stator)
Kailong RADII
H1076
52 VAC
240 VAC 1.5 sec
25 F
20 F
905135-41
905135-42
LSS PART NO. SHIFT
(See note 2)
CAP.
732752-02
732752-00
LSS PART NO.
(See note 2)
903836-01
903836-02
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 8
CPI Canada Inc.
2.0
X-Ray Tube Stator Compatibility Tables
LOW SPEED STARTER TUBE SELECT TABLE (cont)
INDICO IQ only
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
CODE,
INDICO
100 only
OUTPUT RUN
VOLTS
Switches
FREQ.
(1........5)
INDICO 100 /
CMP200/DR only
BOOST
VOLTS
INDICO IQ
(See note 1)
BOOST SHIFT
TIME
CAP.
INDICO 100
LSS PART NO. SHIFT
(See note 2)
CAP.
CMP200 / CMP200 DR
LSS PART NO. SHIFT
(See note 2)
CAP.
LSS PART NO.
(See note 2)
Machlett (see Varian)
Philips
ROT350
ROT351
(36/44  stator)
(See note 4)
* Dunlee tube
(See note 6)
** NAGO tube
*** Varian tube
Philips
ROT350
ROT351
(9/11  stator)
(See note 5)
* Dunlee tube
(See note 6)
** NAGO tube
*** Varian tube
Philips
ROT500
ROT501
RO 1230
RO 1750 / DU 1750*
RO 2050
RO 3050 / DU 3050*
SRO 2250
GD6 3050 **
PG-256 ***
PG-292 ***
RAD-34 ***
RAD-50 ***
Type 9 60 Hz
(10010)
52 VAC
240 VAC 1.5 sec
33 F
30 F
905135-41
905135-43
30 F
732752-00
30 F
903836-00
RO 1230
RO 1750 / DU 1750*
RO 2050
RO 3050 / DU 3050*
SRO 2250
GD6 3050 **
PG-256 ***
PG-292 ***
RAD-34 ***
RAD-50 ***
Type 9 60 Hz
(10010)
N/A
N/A
N/A
33 F
30 F
905135-41
905135-43
N/A
N/A
N/A
N/A
SRM 0310
Type 30 60 Hz
(01111)
N/A
N/A
N/A
33 F
30 F
905135-41
905135-43
N/A
N/A
N/A
N/A
(9/11  stator)
Picker (see Dunlee)
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 9
CPI Canada Inc.
2.0
X-Ray Tube Stator Compatibility Tables
LOW SPEED STARTER TUBE SELECT TABLE (cont)
INDICO IQ only
INDICO
100 only
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
Shimadzu CIRCLEX
RX80
RX81
RX82
(7.5/35  stator)
P18DE-85
Type 16 60 Hz
(00001)
52 VAC
Shimadzu CIRCLEX
RX100
P38E
Type 16 60 Hz
(00001)
Shimadzu CIRCLEX
RX150
(8.4/24  stator)
P18DK
Type 16 60 Hz
(00001)
Siemens Opti-150
“S” stator
(1-phase only)
(14/18 )
* Varian tube
Siemens SV 150
“S” stator
(1-phase only)
(14/18 )
* Varian tube
20/40
30/52R
SG-796B *
SV 150/40/80C-100L
SG-256B *
Siemens (SXVT)
RAY-6_1
RAY-8(S)_1
RAY-12(S)_1
(1-phase only)
(20/50  stator)
Siemens (SXVT)
RAY-13(S)_1
RAY-14(S)_1
(1-phase only)
(20/50  stator)
CODE,
OUTPUT RUN
VOLTS
INDICO 100 /
CMP200/DR only
CMP200 / CMP200 DR
LSS PART NO. SHIFT
(See note 2)
CAP.
120 VAC 1.5 sec
(See
note 10)
33 F
30 F
905135-41
905135-43
30 F
732752-00
30 F
903836-00
52 VAC
120 VAC 1.5 sec
(See
note 10)
33 F
30 F
905135-41
905135-43
30 F
732752-00
30 F
903836-00
52 VAC
120 VAC 1.5 sec
(See
note 10)
33 F
30 F
905135-41
905135-43
30 F
732752-00
30 F
903836-00
52 VAC
120 VAC 2.5 sec N/A
(Indico)
(See
note 10) 2.0 sec
(CMP200)
N/A
45 F
732752-02
40 F
903836-01
Type 23 50 Hz
(11101)
N/A
N/A
33 F
30 F
905135-41
905135-43
N/A
N/A
N/A
N/A
SV 150/12/40-S
SV 150/25/48-S
SV 150/22/54-S
SV 150/33/78R-S
Type 31 60 Hz
(11111)
73 VAC
240 VAC 1.5 sec
33 F
30 F
905135-41
905135-43
30 F
732752-00
30 F
903836-00
SV 150/33/78R-S
Type 31 60 Hz
(11111)
73 VAC
240 VAC 1.5 sec
33 F
30 F
905135-41
905135-43
30 F
732752-00
30 F
903836-00
N/A
N/A
BOOST
TIME
INDICO 100
SHIFT LSS PART NO. SHIFT
CAP. (See note 2)
CAP.
Switches
FREQ.
(1........5)
BOOST
VOLTS
INDICO IQ
(See note 1)
N/A
LSS PART NO.
(See note 2)
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 10
CPI Canada Inc.
2.0
X-Ray Tube Stator Compatibility Tables
LOW SPEED STARTER TUBE SELECT TABLE (cont)
INDICO IQ only
INDICO
100 only
INDICO 100 /
CMP200/DR only
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
Siemens (SXVT)
SDR
(1-phase only)
(20/50  stator)
SDR 150/30/50-1
Type 31 60 Hz
(11111)
73 VAC
240 VAC 1.5 sec
Siemens (SXVT)
SV 150
“S” stator
(1-phase only)
(14/18 )
Toshiba Rotanode
SV 150/40/80C-100_1
Type 23 50 Hz
(11101)
52 VAC
Toshiba
XH-112V-2
XH-112W
XS-AA stator
XS-AG stator
(9.4/28.3 )
Toshiba
XH-121
XH-126
XH-150
XS-AV stator
XS-RA stator
(27.5/58 )
Toshiba
XH-112V-2
XS-AA stator
XS-AG stator
(9.4/28.3 )
(See note 7)
CODE,
OUTPUT RUN
VOLTS
Switches
FREQ.
(1........5)
BOOST
VOLTS
BOOST
TIME
INDICO IQ
(See note 1)
INDICO 100
CMP200 / CMP200 DR
SHIFT LSS PART NO. SHIFT
CAP. (See note 2)
CAP.
LSS PART NO. SHIFT
(See note 2)
CAP.
LSS PART NO.
(See note 2)
33 F
30 F
905135-41
905135-43
30 F
732752-00
30 F
903836-00
120 VAC 2.5 sec 33 F
(Indico) 30 F
(See
note 10) 2.0 sec
(CMP200)
905135-41
905135-43
45 F
732752-02
40 F
903836-01
Most Toshiba x-ray tubes are identified by their “E” number, which is used to represent both the Tube Insert and the complete assembly. The housing
number is usually not shown on the identification label. A specific “E” number may be available with several different stator types, each having different
starter requirements. Furthermore, a specific stator type may require different starter requirements depending on the housing used. For ease of use, the
Toshiba tubes are sorted by Tube Insert Type (“E” number) within this table. The installer must confirm the stator type for the planned tube(s). If the stator
type is not identified within the Toshiba documentation, match the stator winding resistance to the appropriate table entry. Contact the factory if the
desired Tube Type and stator type / winding resistance are not listed on the same row within this table.
N/A
N/A
N/A
33 F 905135-41
DRX-3624H
Type 17 60 Hz
N/A
N/A
N/A
N/A
DRX-3724H
30 F 905135-43
(10001)
DRX-4634H
E7132
E7239
E7240
E7242
(See note 8)
Type 19 60 Hz
(11001)
52 VAC
240 VAC 1.5 sec
E7250
(See note 8)
Type 17 60 Hz
(10001)
N/A
N/A
N/A
25 F
20 F
905135-41
905135-42
30 F
732752-00
20 F
903836-02
33 F
30 F
905135-41
905135-43
N/A
N/A
N/A
N/A
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 11
CPI Canada Inc.
2.0
X-Ray Tube Stator Compatibility Tables
LOW SPEED STARTER TUBE SELECT TABLE (cont)
INDICO IQ only
INDICO
100 only
INDICO 100 /
CMP200/DR only
INDICO IQ
(See note 1)
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
Toshiba
XH-106V
XH-180
XH-181
XS-AL stator
(9.4/28.3 )
E7252
(See note 8)
Toshiba
XH-106V
XH-180
XH-181
XS-RA stator
(27.5/58 )
E7252
(See note 8)
Type 19 60 Hz
(11001)
94 VAC
240 VAC 1.5 sec
25 F
20 F
Toshiba
XH-157
XS-RB stator
(20.2/38 )
E7254
E7255
(See note 8)
Type 21 60 Hz
(10101)
52 VAC
240 VAC 1.5 sec
Toshiba
XH-121
XH-126
XS-AV stator
XS-RA stator
(27.5/58 )
Toshiba
XH-106V
XH-180
XS-AL stator
(9.4/28.3 )
E7299
(See note 8)
Type 19 60 Hz
(11001)
52 VAC
E7813
(See note 8)
Type 29 60 Hz
(10111)
52 VAC
CODE,
OUTPUT RUN
VOLTS
Switches
FREQ.
(1........5)
Type 29 60 Hz
(10111)
52 VAC
BOOST
VOLTS
BOOST SHIFT
TIME
CAP.
LSS PART NO. SHIFT
(See note 2)
CAP.
CMP200 / CMP200 DR
LSS PART NO. SHIFT
(See note 2)
CAP.
LSS PART NO.
(See note 2)
45 F
(50 or
60 Hz)
732752-02
(prefer)
40 F
(50 or
60 Hz)
903836-01
(prefer)
30 F
(60 Hz
only)
732752-00
30 F
(60 Hz
only)
903836-00
905135-41
905135-42
30 F
732752-00
20 F
903836-02
33 F
30 F
905135-41
905135-43
30 F
(60 Hz
only)
732752-00
30 F
(60 Hz
only)
903836-00
240 VAC 1.5 sec
25 F
20 F
905135-41
905135-42
30 F
732752-00
20 F
903836-02
120 VAC 1.5 sec
(See
note 10)
45 F
40 F
905135-41
905135-44
45 F
(50 or
60 Hz)
30 F
(60 Hz
only)
732752-02
(prefer)
40 F
(50 or
60 Hz)
30 F
(60 Hz
only)
903836-01
(prefer)
120 VAC 1.5 sec
(See
note 10)
45 F
40 F
INDICO 100
905135-41
905135-44
732752-00
903836-00
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 12
CPI Canada Inc.
2.0
X-Ray Tube Stator Compatibility Tables
LOW SPEED STARTER TUBE SELECT TABLE (cont)
INDICO IQ only
INDICO
100 only
INDICO 100 /
CMP200/DR only
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
Toshiba
XH-121
XS-BA stator
(18/47.5 )
E7843
(See note 8)
Toshiba
XH-121
XH-126
XH-150
XS-RA stator
(27.5/58 )
Toshiba
XH-112V-2
XS-AG stator
(9.4/28.3 )
Toshiba
XH-121
XS-AV stator
(27.5/58 )
Toshiba
XH-112V-2
XS-AG stator
(9.4/28.3 )
Toshiba
XH-121
XS-AV-stator
XS-RA stator
(27.5/58 )
E7861
(See note 8)
Type 19 60 Hz
(11001)
94 VAC
240 VAC 1.5 sec
E7864
(See note 8)
Type 17 60 Hz
(10001)
N/A
N/A
E7865
(See note 8)
Type 19 60 Hz
(11001)
52 VAC
240 VAC 1.5 sec
CODE,
OUTPUT RUN
VOLTS
Switches
FREQ.
(1........5)
Type 0 60 Hz
(00000)
52 VAC
BOOST
VOLTS
INDICO IQ
(See note 1)
BOOST SHIFT
TIME
CAP.
120 VAC 2.5 sec
(See
note 10)
N/A
N/A
E7869
(See note 8)
Type 17 60 Hz
(10001)
N/A
N/A
E7876
(See note 8)
Type 19 60 Hz
(11001)
94 VAC
240 VAC 1.5 sec
33 F
30 F
INDICO 100
LSS PART NO. SHIFT
(See note 2)
CAP.
905135-41
905135-43
CMP200 / CMP200 DR
LSS PART NO. SHIFT
(See note 2) CAP.
LSS PART NO.
(See note 2)
45 F
(50 or
60 Hz)
732752-02
(prefer)
40 F
(50 or
60 Hz)
903836-01
(prefer)
30 F
(60 Hz
only)
732752-00
30 F
(60 Hz
only)
903836-00
25 F
20 F
905135-41
905135-42
30 F
732752-00
20 F
903836-02
33 F
30 F
905135-41
905135-43
N/A
N/A
N/A
N/A
25 F
20 F
905135-41
905135-42
30 F
732752-00
20 F
903836-02
MOBILE DR GENERATOR
30 F
904832-00
33 F
30 F
905135-41
905135-43
N/A
N/A
N/A
N/A
25 F
20 F
905135-41
905135-42
30 F
732752-00
20 F
903836-02
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 13
CPI Canada Inc.
2.0
X-Ray Tube Stator Compatibility Tables
LOW SPEED STARTER TUBE SELECT TABLE (cont)
INDICO IQ only
INDICO
100 only
INDICO 100 /
CMP200/DR only
INDICO IQ
(See note 1)
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
Toshiba
XH-121
XH-126
XH-150
XS-AL stator
(9.4/28.3 )
E7884
(See note 8)
Toshiba
XH-121
XH-126
XS-AV stator
XS-RA stator
(27.5/58 )
Varian (Machlett)
Dynamax (DX) 52
“R” stator (16/50 )
Varian (Machlett)
Dynamax (DX) 62
“R” stator
(23/56 )
E7886
(See note 8)
Type 19 60 Hz
(11001)
94 VAC
240 VAC 1.5 sec
25 F
20 F
A-102
A-132
A-142
Type 0 60 Hz
(00000)
52 VAC
240 VAC 1.5 sec
A-192B
A-196
A-197
A-256
A-272
A-282
A-286
A-292
A-482
A-486
A-102
A-132 / A-134*
A-142 / A-144*
A-145
* (See note 9)
Type 0 60 Hz
(00000)
Type 1
(10000)
52 VAC
Type 2 60 Hz
(01000)
52 VAC
Dynamax (DX) 62U
configured as
“STD” or “R” stator
(15/36 )
Varian
B-100
“STD” stator
(16/50 )
CODE,
OUTPUT RUN
VOLTS
Switches
FREQ.
(1........5)
Type 29 60 Hz
(10111)
52 VAC
BOOST
VOLTS
BOOST SHIFT
TIME
CAP.
LSS PART NO. SHIFT
(See note 2)
CAP.
CMP200 / CMP200 DR
LSS PART NO. SHIFT
(See note 2) CAP.
45 F
(50 or
60 Hz)
30 F
(60 Hz
only)
732752-02
(prefer)
905135-41
905135-42
30 F
33 F
30 F
905135-41
905135-43
240 VAC 1.5 sec
33 F
30 F
240 VAC 1.5 sec
33 F
30 F
120 VAC 1.5 sec
(See
note 10)
45 F
40 F
INDICO 100
LSS PART NO.
(See note 2)
40 F
(50 or
60 Hz)
30 F
(60 Hz
only)
903836-01
(prefer)
732752-00
20 F
903836-02
30 F
732752-00
30 F
903836-00
905135-41
905135-43
30 F
732752-00
30 F
903836-00
905135-41
905135-43
30 F
732752-00
30 F
903836-00
905135-41
905135-44
732752-00
903836-00
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 14
CPI Canada Inc.
2.0
X-Ray Tube Stator Compatibility Tables
LOW SPEED STARTER TUBE SELECT TABLE (cont)
INDICO IQ only
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
Varian
B-130
B-130H
B-135H
B-146
B-147
B-150
B-150H
Std “R” stator
(16/50 )
A-152
A-182 / A-184*
A-192 / A-194*
A-195
A-196 A-197
* (See note 9)
A-272 / A-274*
A-277 / A-278*
A-282 / A-284*
A-286
A-292 / A-294*
A-482
G-242 G-256
G-292 / G-294*
G-296
G-892 G-896
* (See note 9)
G-1077
G-1078
G-1080
G-1082 / G-1084*
G-1086 / G-1087*
G-1092 / G-1094*
* (See note 9)
G-1582
G-1592
G-1593
Varian
B-160
B-160H
B-165H
“R” Stator
(16/50 )
Varian
B-180
B-180H
B-185
B-185H
“R” Stator
(16/50 )
CODE,
INDICO
100 only
OUTPUT RUN
VOLTS
Switches
FREQ.
(1........5)
INDICO 100 /
CMP200/DR only
BOOST
VOLTS
INDICO IQ
(See note 1)
BOOST SHIFT
TIME
CAP.
INDICO 100
LSS PART NO. SHIFT
(See note 2)
CAP.
CMP200 / CMP200 DR
LSS PART NO. SHIFT
(See note 2)
CAP.
LSS PART NO.
(See note 2)
52 VAC
240 VAC 1.5 sec
33 F
30 F
905135-41
905135-43
30 F
732752-00
30 F
903836-00
Type 15 60 Hz
(11110)
N/A
N/A
N/A
33 F
30 F
905135-41
905135-43
N/A
N/A
N/A
N/A
Type 15 60 Hz
(11110)
N/A
N/A
N/A
33 F
30 F
905135-41
905135-43
N/A
N/A
N/A
N/A
Type 2 60 Hz
(00000)
Type 1
(10000)
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 15
CPI Canada Inc.
2.0
X-Ray Tube Stator Compatibility Tables
LOW SPEED STARTER TUBE SELECT TABLE (cont)
INDICO IQ only
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
Varian
B-199
“S” Stator
(15/18 )
Varian (Eureka)
Diamond
LEO
Std “R” stator
(20/50 )
Varian (Eureka)
Diamond
Std “R” stator
(20/50 )
Varian (Eureka)
Diamond
Emerald
Std “R” stator
(20/50 )
Varian (Eureka)
Sapphire
Std “R” stator
(20/50 )
SG-1096
Type 18 50 Hz
(01001)
RAD-12
RAD-13
RAD-14
RAD-68
CODE,
INDICO
100 only
OUTPUT RUN
VOLTS
INDICO 100 /
CMP200/DR only
INDICO IQ
(See note 1)
BOOST
VOLTS
BOOST SHIFT
TIME
CAP.
N/A
N/A
N/A
Type 0 60 Hz
(00000)
52 VAC
Type 0 60 Hz
(00000)
52 VAC
RAD-8
RAD-74
Type 0 60 Hz
(00000)
52 VAC
RAD-21
RAD-40
RAD-44
RAD-56
RAD-60
RAD-92
RAD-94
Type 5 60 Hz
(10100)
52 VAC
Switches
FREQ.
(1........5)
INDICO 100
CMP200 / CMP200 DR
LSS PART NO. SHIFT
(See notes 2) CAP.
LSS PART NO. SHIFT
(See note 2)
CAP.
LSS PART NO.
(See note 2)
33 F
30 F
905135-41
905135-43
N/A
N/A
N/A
N/A
240 VAC 1.5 sec
33 F
30 F
905135-41
905135-43
30 F
732752-00
30 F
903836-00
240 VAC 1.5 sec
33 F
30 F
905135-41
905135-43
30 F
732752-00
30 F
903836-00
240 VAC 1.5 sec
33 F
30 F
905135-41
905135-43
30 F
732752-00
30 F
903836-00
240 VAC 1.5 sec
33 F
30 F
905135-41
905135-43
30 F
732752-00
30 F
903836-00
MOBILE DR GENERATOR
30 F
904832-00
NOTE 1:
For Indico IQ generators, the 905135-41 “universal” starter provides automatic selection of shift capacitance using relays located on the Low Speed
Starter board. The dedicated 905135-42, 905135-43 and 905135-44 starters provide a fixed value using a single capacitor.
NOTE 2:
Where more than one Low Speed Starter part number is referenced for a particular tube type and generator combination, any of these is acceptable.
In some cases, a preferred part number is identified. For 2-tube systems using different tube types, both tube types must be considered.
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 16
CPI Canada Inc.
2.0
X-Ray Tube Stator Compatibility Tables
LOW SPEED STARTER TUBE SELECT TABLE (cont)
NOTE 3:
Comet tube inserts with the prefix “DI” and “DX” are interchangeable.
NOTE 4:
Philips / Dunlee housing with the windings connected in series (low-speed / high impedance configuration).
NOTE 5:
Philips / Dunlee housing with the windings connected in parallel (high-speed / low impedance configuration).
NOTE 6:
Dunlee tube inserts with the prefix “DU” and Philips tube inserts with the prefix “RO” are interchangeable. Select the corresponding Philips insert type
within the Generator software if the Dunlee type is not available.
NOTE 7:
Siemens (SXVT) housing with the “phase-shifted” windings connected in parallel (low impedance, high speed configuration).
NOTE 8:
Complete Toshiba x-ray tube assemblies include the suffix “X, “FX”, “GX”, or “JX”, which are interchangeable with respect to rotor and anode
characteristics.
NOTE 9:
These X-ray tubes incorporate a control grid. Grid control is currently not supported by CPI generators. Connect the grid connection to Ground when
using these tubes, and select the insert type within the Generator software corresponding to the equivalent non-grid tube.
NOTE 10:
The starter boost voltage is 120 VAC. This is not available with two-tube Indico 100 generators.
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 17
CPI Canada Inc.
3.0
X-Ray Tube Stator Compatibility Tables
DUAL SPEED STARTER TUBE SELECT TABLE
The Dual Speed Starter (DSS) synthesizes its output frequencies independently of the line frequency and will operate all tubes at 60/180 Hz, unless a
particular tube only has published ratings to operate at 150 Hz. In this case, the starter will output 50/150 Hz when set for these tubes.
Unless indicated otherwise within Table 2, setting the switches to the code indicated for the applicable Tube Type selects all required operating parameters.
The Dual Speed Starter part number corresponds to the AC line voltage (except Indico IQ) and the configuration of phase-shift capacitors installed.
Reference notes are provided at the end of Table 2. Tube operating parameters for each switch code are contained in Table 3 for reference.
TABLE 2: TUBE TYPES (HIGH SPEED STARTER)
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
CGR (GE)
Statorix
200A/240/260
(50/110  stator)
CGR (GE)
Statorix 550
(50/110  stator)
CODE,
OPERATING NOTES
Switches
(1........5)
(SEE TABLE 3 FOR OPERATING PARAMETERS)
MN640
M641
MN641
M643
Type 28
(00111)
LOW SPEED OPERATION ONLY
(See note 1)
MS740
MSN740
MSN742
RSN742
Type 28
(00111)
RN620
RN621
Type 28
(00111)
RSN722
Type 28
(00111)
Dual Speed Starters “-15” must be
jumper-configured to provide the
required 15.5 F low speed shift
capacitance. Please see note 10
before attempting to use this Dual
Speed Starter configuration.
HIGH SPEED OPERATION ONLY
(See note 1)
For Dual Speed operation, contact
factory.
LOW SPEED OPERATION ONLY
(See note 1)
Dual Speed Starters “-15” must be
jumper-configured to provide the
required 15.5 F low speed shift
capacitance. Please see note 10
before attempting to use this Dual
Speed Starter configuration.
HIGH SPEED OPERATION ONLY
(See note 1)
For Dual Speed operation, contact
factory.
OUTPUT
FREQ.
50 Hz
H.S.
SHIFT
CAP.
N/A
L.S.
SHIFT
CAP.
12.5F
to
15.5F
INDICO 100
DSS PART NO.
(See note 2)
733317-15
735925-15
906894-15
(See note 10)
INDICO IQ
DSS PART NO.
(See note 2)
904925-23
CMP 200
DSS PART NO.
(See note 2)
901297-15
901298-15
(See note 10)
906672-23
150 Hz
3 F
12.5F
to
15.5F
733317-15
735925-15
906894-15
(See note 10)
904925-23
50 Hz
N/A
12.5F
to
15.5F
733317-15
735925-15
906894-15
(See note 10)
904925-23
901297-15
901298-15
(See note 10)
906672-23
901297-15
901298-15
(See note 10)
906672-23
150 Hz
3 F
12.5F
to
15.5F
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 18
CPI Canada Inc.
3.0
X-Ray Tube Stator Compatibility Tables
DUAL SPEED STARTER TUBE SELECT TABLE (cont)
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
Chirana
Rotax KA 125
(20/50  stator,
single phase)
CODE,
OPERATING NOTES
60 Hz
H.S.
SHIFT
CAP.
N/A
L.S.
SHIFT
CAP.
30 F
to
36 F
INDICO 100
DSS PART NO.
(See note 2)
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
LOW SPEED OPERATION ONLY
(See note 1)
60 Hz
N/A
30 F
to
36 F
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
Type 0
(00000)
LOW SPEED OPERATION ONLY
(See note 1)
60 Hz
N/A
30 F
to
36 F
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
Type 0
(00000)
LOW SPEED OPERATION ONLY
(See note 1)
60 Hz
N/A
Type 24
(00011)
None
50/150 Hz
6 F
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
Type 24
(10011)
None
50/150 Hz
6 F
30 F
to
36 F
30 F
to
36 F
30 F
to
36 F
Switches
(1........5)
(SEE TABLE 3 FOR OPERATING PARAMETERS)
RIK-T
Type 21
(10101)
LOW SPEED OPERATION ONLY
(See note 1)
Comet
DO7 / DX7
(25/50  stator)
DX7
DX71HS
(See note 3)
Type 0
(00000)
Comet
DO9 / DX9
(20/50  stator)
DX9
DX91H / HS
DX92H / HS
DX93H / HS
DX94HS
DX96HS
DX97HS
(See note 3)
DX10H
(See note 3)
DX10HS
DX104HS
(See note 3)
DX105HS
DX106HS
(See note 3)
Comet
DO10 / DX10
(20/50  stator)
OUTPUT
FREQ.
INDICO IQ
DSS PART NO.
(See note 2)
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
CMP 200
DSS PART NO.
(See note 2)
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 19
CPI Canada Inc.
3.0
X-Ray Tube Stator Compatibility Tables
DUAL SPEED STARTER TUBE SELECT TABLE (cont)
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
Switches
Comet
DO700 / DX700
(25/50  stator)
DX700HS
(See note 3)
(1........5)
Type 24
(10011)
Dunlee (Philips)
DA10 series
(20/50  stator)
DA1002 (DU304-1.0/2.0)
DA1029 (DU304-0.6/1.2)
DA1036 (DU404-0.6/1.2)
DA1083 (DU404-0.3/1.0)
DA1092 (DU604-0.6/1.2)
DA1094 (DU404-0.4/0.8)
Dunlee (Philips)
DA90 DA90HS
(36/44  stator)
(See note 4)
DU 1750
DU 3050
DU 2550
DU 33100
(See note 6)
DU 1750
DU 3050
(See note 6)
DU 2550
(See note 6)
DU 33100
(See note 6)
DR1429 (DU304-0.6/1.2)
DR1436 (DU404-0.6/1.2)
DR1492 (DU604-0.6/1.2)
DR1494 (DU404-0.4/0.8)
Dunlee (Philips)
DA90
DA90HS
(9/11  stator)
(See note 5)
Dunlee (Philips)
DR1400
(20/50  stator)
CODE,
OPERATING NOTES
None
50/150 Hz
H.S.
SHIFT
CAP.
6 F
Type 4
(00100)
None
60/180 Hz
6 F
30 F
to
36 F
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
Type 9
(10010)
LOW SPEED OPERATION
ONLY (See note 1)
60 Hz
N/A
30F
733317-13
735925-13
906894-13
Type 9
(10010)
LOW SPEED OPERATION
ONLY (See note 1)
60 Hz
N/A
37.5F
904925-21
904925-23
Type 9
(10010)
Type 9
(10010)
Type 4
(00100)
None
60/180 Hz
12.5F
37.5F
901297-16
901298-16
906672-21
906672-23
HIGH SPEED OPERATION
ONLY (See note 1)
None
180 Hz
12.5F
37.5F
733317-16
735925-16
906894-16
733317-17
735925-17
906894-17
60/180 Hz
6 F
30 F
to
36 F
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
(SEE TABLE 3 FOR OPERATING
PARAMETERS)
OUTPUT
FREQ.
L.S.
SHIFT
CAP.
30 F
to
36 F
INDICO 100
DSS PART NO.
(See note 2)
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
INDICO IQ
DSS PART NO.
(See note 2)
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
904556-13
903255-13
904925-21
904925-23
CMP 200
DSS PART NO.
(See note 2)
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
901297-13
901298-13
906672-21
906672-23
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 20
CPI Canada Inc.
3.0
X-Ray Tube Stator Compatibility Tables
DUAL SPEED STARTER TUBE SELECT TABLE (cont)
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
Dunlee (Philips)
DR 1800
(19/22  stator)
(See note 4)
DR1817
Dunlee (Philips)
DR 1800
(9/11  stator)
(See note 5)
DR1817
DR1825
DR1833
Dunlee
(Picker / Philips)
PX1300
3” anode
“S“ stator
(15/30 )
PX1302 (DU303-1.0/2.0)
PX1312 (DU303-0.6/1.2)
PX1351 (DU143-1.0/2.0)
Dunlee
(Picker / Philips)
PX1400 series
4” anode
“S” stator
(15/30 )
PX1402 (DU304-1.0/2.0)
PX1412 (DU304-0.6/1.2)
PX1415 (DU404-0.3/0.9)
PX1425
PX1429 (DU304-0.6/1.2)
PX1431 (DU304-0.7/1.4)
PX1436 (DU404-0.6/1.2)
PX1456 (DU404-0.3/1.0)
PX1463 (DU604-0.6/1.2)
PX1472 (DU604-0.3/1.0)
PX1473 (DU404-0.6/1.2)
PX1475 (DU754-0.6/1.2)
PX1482 (DU404-0.6/1.0)
PX1483 (DU404-0.3/1.0)
PX1492 (DU604-0.6/1.2)
PX1494 (DU404-0.4/0.8)
Dunlee
(Picker / Philips)
PX1400 series
4” anode
“Q” stator
(6/12 )
CODE,
LOW SPEED OPERATION
ONLY (See note 1)
60 Hz
H.S.
SHIFT
CAP.
N/A
Type 9
(10010)
Type 9
(10010)
Type 9
(10010)
Type 7
(11100)
LOW SPEED OPERATION
ONLY (See note 1)
HIGH SPEED OPERATION
ONLY (See note 1)
None
60 Hz
N/A
37.5F
180 Hz
12.5F
37.5F
60/180 Hz
12.5F
37.5F
None
60/180 Hz
6 F
30 F
to
36 F
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
Type 1
(10000)
None
60/180 Hz
6 F
30 F
to
36 F
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
Type 13
(10110)
None
60/180 Hz
20 F
60 F
to
62 F
733317-02
735925-02
906894-02
Switches
(1........5)
Type 9
(10010)
OPERATING NOTES
(SEE TABLE 3 FOR OPERATING
PARAMETERS)
OUTPUT
FREQ.
L.S.
SHIFT
CAP.
30F
to
32F
INDICO 100
DSS PART NO.
(See note 2)
733317-13
735925-13
906894-13
733317-16
735925-16
906894-16
733317-17
735925-17
906894-17
INDICO IQ
DSS PART NO.
(See note 2)
904556-13
903255-13
904925-21
904925-22
904925-23
904925-21
904925-23
CMP 200
DSS PART NO.
(See note 2)
901297-13
901298-13
906672-21
906672-22
906672-23
901297-16
901298-16
906672-21
906672-23
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
904925-22
901297-02
901298-02
906672-22
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 21
CPI Canada Inc.
3.0
X-Ray Tube Stator Compatibility Tables
DUAL SPEED STARTER TUBE SELECT TABLE (cont)
TUBE TYPE
(HOUSING)
(SEE TABLE 3 FOR OPERATING PARAMETERS)
OUTPUT
FREQ.
H.S.
SHIFT
CAP.
L.S.
SHIFT
CAP.
INDICO 100
DSS PART NO.
(See note 2)
INDICO IQ
DSS PART NO.
(See note 2)
CMP 200
DSS PART NO.
(See note 2)
Type 14
(01110)
None
60/180 Hz
7.5 F
36 F
to
37.5F
733317-12
735925-12
906894-12
904556-12
903255-12
904925-21
901297-12
901298-12
906672-21
MX-100
Type 20
(00101)
None
60/180 Hz
7.5 F
36 F
to
37.5F
733317-12
735925-12
906894-12
904556-12
903255-12
904925-21
901297-12
901298-12
906672-21
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
TUBE TYPE
(INSERT)
CODE,
Switches
(1........5)
OPERATING NOTES
Eureka (see Varian)
GE Maxiray 75
(3” anode)
23/23 equal
impedance “E”
stator
* Dunlee tube
GE Maxiray 100
(4” anode)
23/23  equal
impedance “E”
stator
Gilardoni
Rotagil
(33/36  stator)
MX-75
AR11-30
AR30-60
Type 22
(01101)
LOW SPEED OPERATION ONLY
(See note 1)
50 Hz
N/A
30 F
to
36 F
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
Gilardoni
Rotagil
A/A5
(33/36  stator)
AR20-50
AR30-100
AR40-100
Type 22
(01101)
None
50/150 Hz
6 F
30 F
to
36 F
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
DU303 (1.0/2.0) *
DU303 (0.6/1.2) *
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 22
CPI Canada Inc.
3.0
X-Ray Tube Stator Compatibility Tables
DUAL SPEED STARTER TUBE SELECT TABLE (cont)
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
IAE
C30
C31
(25/62  stator)
IAE
C40
(28/57.5  stator)
(33/64  stator)
IAE
C52
C52 Super
C100
C352
(20/40  stator)
CODE,
OPERATING NOTES
50 Hz
H.S.
SHIFT
CAP.
N/A
L.S.
SHIFT
CAP.
30 F
to
36 F
None
50/150 Hz
6 F
Type 19
(11001)
LOW SPEED OPERATION ONLY
(See note 1)
60 Hz
N/A
30 F
to
36 F
20 F
to
30 F
Type 27
(11011)
LOW SPEED OPERATION ONLY
(See note 1)
50 Hz
N/A
30 F
to
36 F
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
Type 27
(11011)
None
50/150 Hz
5 F
30 F
733317-13
735925-13
906894-13
733317-17
735925-17
906894-17
Switches
(1........5)
(SEE TABLE 3 FOR OPERATING PARAMETERS)
X20P
X22
X40
RTM 70H
RTM 70HS
Type 10
(01010)
LOW SPEED OPERATION ONLY
(See note 1)
Type 10
(01010)
X39
X40
X42
X76
RTM 78H
RTM 90H
RTM 92H
RTM 101H
RTM 102H
RTM 780H
RTM 782H
X39 X40
X42 X50H
X50AH
RTC 600HS
RTC 700HS
RTC 1000HS
RTM 78HS
RTM 90HS
RTM 92HS
RTM 101HS
RTM 102HS
RTM 780HS
RTM 782HS
OUTPUT
FREQ.
INDICO 100
DSS PART NO.
(See note 2)
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
INDICO IQ
DSS PART NO.
(See note 2)
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
CMP 200
DSS PART NO.
(See note 2)
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
733317-13
735925-13
906894-13
904556-13
903255-13
904925-21
904925-22
904925-23 *
* Preferred
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
901297-13
901298-13
906672-21
906672-22
906672-23 *
* Preferred
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
904556-13
903255-13
904925-21
904925-22
901297-13
901298-13
906672-21
906672-22
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 23
CPI Canada Inc.
3.0
X-Ray Tube Stator Compatibility Tables
DUAL SPEED STARTER TUBE SELECT TABLE (cont)
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
CODE,
OPERATING NOTES
OUTPUT
FREQ.
H.S.
SHIFT
CAP.
L.S.
SHIFT
CAP.
INDICO 100
DSS PART NO.
(See note 2)
INDICO IQ
DSS PART NO.
(See note 2)
CMP 200
DSS PART NO.
(See note 2)
LOW SPEED OPERATION ONLY
(See note 1)
60 Hz
N/A
30F
to
32F
733317-13
735925-13
906894-13
904556-13
903255-13
904925-21
904925-22
904925-23
901297-13
901298-13
906672-21
906672-22
906672-23
Type 9
(10010)
LOW SPEED OPERATION ONLY
(See note 1)
60 Hz
N/A
37.5F
904925-21
904925-23
901297-16
901298-16
906672-21
906672-23
Type 9
(10010)
None
60/180 Hz
12.5F
37.5F
733317-16
735925-16
906894-16
733317-17
735925-17
906894-17
Type 9
(10010)
HIGH SPEED OPERATION ONLY
(See note 1)
180 Hz
12.5F
37.5F
Switches
(1........5)
(SEE TABLE 3 FOR OPERATING PARAMETERS)
Type 9
(10010)
Machlett (see Varian)
Philips
ROT 350
ROT 351
(36/44  stator)
(See note 4)
* Dunlee tube
(See note 6)
** NAGO tube
*** Varian tube
Philips
ROT 350
ROT 351
(9/11  stator)
(See note 5)
* Dunlee tube
(See note 6)
*** Varian tube
RO 1230
RO 1750
RO 2050
RO 3050
SRO 2250
DU 1750 *
DU 3050 *
GD6 3050 **
PG-256 ***
PG-292 ***
RAD-34 ***
RAD-50 ***
RO 1230
RO 1750
RO 3050
DU 1750 *
DU 3050 *
RO 2050
SRO 2250
PG-256 ***
PG-292 ***
RAD-34 ***
RAD-50 ***
RO 2550
RO 33100
SRO 1330
DU 2550 *
DU 33100 *
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 24
CPI Canada Inc.
3.0
X-Ray Tube Stator Compatibility Tables
DUAL SPEED STARTER TUBE SELECT TABLE (cont)
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
Philips
ROT 500
ROT 501
(9/11  stator)
SRM 0310
SRM 1080
SRM 35100
Switches
(1........5)
CODE,
OPERATING NOTES
(SEE TABLE 3 FOR OPERATING PARAMETERS)
OUTPUT
FREQ.
60/180 Hz
H.S.
SHIFT
CAP.
12.5F
L.S.
SHIFT
CAP.
37.5F
Type 30
(01111)
Type 30
(01111)
None
HIGH SPEED OPERATION ONLY
(See note 1)
180 Hz
12.5F
37.5F
INDICO 100
DSS PART NO.
(See note 2)
733317-16
735925-16
906894-16
733317-17
735925-17
906894-17
INDICO IQ
DSS PART NO.
(See note 2)
904925-21
904925-23
CMP 200
DSS PART NO.
(See note 2)
901297-16
901298-16
906672-21
906672-23
904556-13
903255-13
904925-21
904925-22
904556-13
903255-13
904925-21
904925-22
904556-13
903255-13
904925-21
904925-22
904556-13
903255-13
904925-21
904925-22
901297-13
901298-13
906672-21
906672-22
901297-13
901298-13
906672-21
906672-22
901297-13
901298-13
906672-21
906672-22
901297-13
901298-13
906672-21
906672-22
Picker (see Dunlee)
Shimadzu
(Circlex)
RX80
RX81
RX82
(7.5/35  stator)
P18DE-85
Type 16
(00001)
LOW SPEED OPERATION ONLY
(See note 1)
60 Hz
N/A
30 F
733317-13
735925-13
906894-13
P33D
P38D
P38DE-85
Type 16
(00001)
HIGH SPEED OPERATION ONLY
(See note 1)
180 Hz
5 F
30 F
733317-13
735925-13
906894-13
Shimadzu
(Circlex)
RX100
P38E
Type 16
(00001)
None
60/180 Hz
5 F
30 F
733317-13
735925-13
906894-13
Shimadzu
(Circlex)
P18DK
Type 16
(00001)
LOW SPEED OPERATION ONLY
(See note 1)
60 Hz
N/A
30 F
733317-13
735925-13
906894-13
P38DK
P324DK
Type 16
(00001)
HIGH SPEED OPERATION ONLY
(See note 1)
180 Hz
5 F
30 F
RX150
(8.4/24  stator)
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 25
CPI Canada Inc.
3.0
X-Ray Tube Stator Compatibility Tables
DUAL SPEED STARTER TUBE SELECT TABLE (cont)
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
Siemens
Biangulix
“S” stator
(1-phase only)
(14/18 )
Siemens Opti-150
“S” stator
(1-phase only)
(14/18 )
BI 125/20/40
BI 125/30/50
BI 150/30/50
BI 150/30/52R
* Varian tube
Siemens OptiTop
“S” stator
(1-phase only)
(14/18 )
150/30/52R
150/40/72C
150/12/50
150/40/80
150/30/50
150/40/102C
SG-796B *
150/40/80HC-100L
150/40/80HC-102L
* Varian tube
Siemens Optilix
“S” stator
(1-phase only)
(14/18 )
SG-1096 *
150/30/50C-100L
150/40/80C-100L
* Varian tube
Siemens Megalix
Siemens SV 125
“S” stator
(1-phase only)
(14/18 )
SG-256 *
Siemens SV 150
“S” stator
(1-phase only)
(14/18 )
* Varian tube
OUTPUT
FREQ.
H.S.
SHIFT
CAP.
L.S.
SHIFT
CAP.
INDICO 100
DSS PART NO.
(See note 2)
INDICO IQ
DSS PART NO.
(See note 2)
CMP 200
DSS PART NO.
(See note 2)
HIGH SPEED OPERATION ONLY
(See note 1)
150 Hz
5 F
30 F
733317-13
735925-13
906894-13
904556-13
903255-13
904925-21
904925-22
901297-13
901298-13
906672-21
906672-22
Type 23
(11101)
HIGH SPEED OPERATION ONLY
(See note 1)
150 Hz
5 F
30 F
733317-13
735925-13
906894-13
904556-13
903255-13
904925-21
904925-22
901297-13
901298-13
906672-21
906672-22
Type 23
(11101)
None
HIGH SPEED OPERATION ONLY
(See note 1)
150 Hz
150 Hz
5 F
5 F
30 F
30 F
733317-13
735925-13
906894-13
904556-13
903255-13
904925-21
904925-22
901297-13
901298-13
906672-21
906672-22
Type 23
(11101)
None
HIGH SPEED OPERATION ONLY
(See note 1)
150 Hz
150 Hz
5 F
5 F
30 F
30 F
733317-13
735925-13
906894-13
904556-13
903255-13
904925-21
904925-22
901297-13
901298-13
906672-21
906672-22
None
150 Hz
5 F
30 F
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
904556-13
903255-13
904925-21
904925-22
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
901297-13
901298-13
906672-21
906672-22
CODE,
OPERATING NOTES
Switches
(SEE TABLE 3 FOR OPERATING PARAMETERS)
(1........5)
Type 23
(11101)
125/30/82CM-120LW
125/40/82CM-120LW
Type 8
(00010)
HIGH SPEED OPERATION ONLY
(See note 1)
150 Hz
6 F
30 F
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
SV 150/30/50C-100L
Type 23
(11101)
HIGH SPEED OPERATION ONLY
(See note 1)
150 Hz
5 F
30 F
733317-13
735925-13
906894-13
None
150 Hz
5 F
30 F
SG-296B *
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 26
CPI Canada Inc.
3.0
X-Ray Tube Stator Compatibility Tables
DUAL SPEED STARTER TUBE SELECT TABLE (cont)
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
Siemens SV 150
“S” stator
(1-phase only)
(14/18 )
SV 150/40/80C-100L
SG-796B *
Switches
(1........5)
(SEE TABLE 3 FOR OPERATING PARAMETERS)
OUTPUT
FREQ.
Type 23
(11101)
None
CODE,
OPERATING NOTES
60/180 Hz
H.S.
SHIFT
CAP.
5 F
L.S.
SHIFT
CAP.
30 F
INDICO 100
DSS PART NO.
(See note 2)
733317-13
735925-13
906894-13
INDICO IQ
DSS PART NO.
(See note 2)
904556-13
903255-13
904925-21
904925-22
CMP 200
DSS PART NO.
(See note 2)
901297-13
901298-13
906672-21
906672-22
* Varian tube
Siemens (SXVT)
RAY-6_1
RAY-8(S)_1
RAY-12(S)_1
(1-phase only)
(20/50  stator)
SV 150/12/40-S
SV 150/25/48-S
SV 150/22/54-S
Type 31
(11111)
LOW SPEED OPERATION ONLY
(See note 1)
60 Hz
N/A
30 F
733317-13
735925-13
906894-13
904556-13
903255-13
904925-21
904925-22
904925-23
901297-13
901298-13
906672-21
906672-22
906672-23
Siemens (SXVT)
RAY-13(S)_1
RAY-14(S)_1
(1-phase only)
(20/50  stator)
SV 150/33/78R-S
Type 31
(11111)
None
60/180 Hz
5 F
30 F
733317-13
735925-13
906894-13
904556-13
903255-13
904925-21
904925-22
901297-13
901298-13
906672-21
906672-22
Siemens (SXVT)
SDR
(1-phase only)
(20/50  stator)
SDR 150/30/50-1
Type 31
(11111)
None
60/180 Hz
5 F
30 F
733317-13
735925-13
906894-13
904556-13
903255-13
904925-21
904925-22
901297-13
901298-13
906672-21
906672-22
Siemens (SXVT)
SV 150
“S” stator
(1-phase only)
(14/18 )
SV 150/40/80C-100_1
Type 23
(11101)
None
150 Hz
5 F
30 F
733317-13
735925-13
906894-13
904556-13
903255-13
904925-21
904925-22
901297-13
901298-13
906672-21
906672-22
(See note 7)
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 27
CPI Canada Inc.
3.0
X-Ray Tube Stator Compatibility Tables
DUAL SPEED STARTER TUBE SELECT TABLE (cont)
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
Toshiba Rotanode
Most Toshiba x-ray tubes are identified by their “E” number, which is used to represent both the Tube Insert and the complete assembly. The housing
number is usually not shown on the identification label. A specific “E” number may be available with several different stator types, each having different
starter requirements. Furthermore, a specific stator type may require different starter requirements depending on the housing used. For ease of use, the
Toshiba tubes are sorted by Tube Type (“E” number) within this table. The installer must confirm the stator type for the planned tube(s). If the stator type is
not identified within the Toshiba documentation, match the stator winding resistance to the appropriate table entry. Contact the factory if the desired Tube
Type and stator type / winding resistance are not listed on the same line within this table.
DRX-3624H
30 F
Type 17
None
60/180 Hz 6 F
733317-12
904556-12
901297-12
DRX-3724H
to
735925-12
903255-12
901298-12
(10001)
DRX-4634H
906894-12
904556-13
901297-13
36 F
733317-13
903255-13
901298-13
735925-13
904925-21
906672-21
906894-13
904925-22
906672-22
904925-23
906672-23
20 F
E7132
Type 19
60 Hz
N/A
733317-13
904556-13
901297-13
LOW SPEED OPERATION ONLY
to
E7239
735925-13
903255-13
901298-13
(11001)
(See note 1)
E7240
906894-13
904925-21
906672-21
30 F
E7242
904925-22
906672-22
904925-23 *
906672-23 *
(See note 8)
* Preferred
* Preferred
Toshiba
XH-112V-2
XH-112W
XS-AA stator
XS-AG stator
(9.4/28.3 )
Toshiba
XH-121
XH-126
XH-150
XS-AV stator
XS-RA stator
(27.5/58 )
Toshiba
XH-112V
XS-AG stator
(9.4/28.3 )
E7250
(See note 8)
CODE,
Switches
(1........5)
Type 17
(10001)
OPERATING NOTES
(SEE TABLE 3 FOR OPERATING PARAMETERS)
None
OUTPUT
FREQ.
60/180 Hz
H.S.
SHIFT
CAP.
6 F
L.S.
SHIFT
CAP.
30 F
to
36 F
INDICO 100
DSS PART NO.
(See note 2)
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
INDICO IQ
DSS PART NO.
(See note 2)
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
CMP 200
DSS PART NO.
(See note 2)
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 28
CPI Canada Inc.
3.0
X-Ray Tube Stator Compatibility Tables
DUAL SPEED STARTER TUBE SELECT TABLE (cont)
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
Toshiba
XH-106V
XH-180
XH-181
XS-AL stator
(9.4/28.3 )
Toshiba
XH-106V
XH-180
XH-181
XS-RA stator
(27.5/58 )
Switches
(1........5)
(SEE TABLE 3 FOR OPERATING PARAMETERS)
OUTPUT
FREQ.
E7252
(See note 8)
Type 29
(10111)
None
E7252
(See note 8)
Type 19
(11001)
CODE,
OPERATING NOTES
60/180 Hz
H.S.
SHIFT
CAP.
6 F
L.S.
SHIFT
CAP.
30 F
to
36 F
INDICO 100
DSS PART NO.
(See note 2)
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
Dual Speed Starters “-15” must be
jumper-configured to provide the
required 28 F low speed shift
capacitance.
Please refer to note 10 before
attempting to use this Dual Speed
Starter configuration.
LOW SPEED OPERATION ONLY
(See note 1)
60/180 Hz
3 F
23 F
to
28 F
733317-15
735925-15
906894-15
(See note 10)
60 Hz
N/A
20 F
to
30 F
733317-13
735925-13
906894-13
Toshiba
XH-157
XS-RB stator
(20.2/38 )
E7254
E7255
(See note 8)
Type 21
(10101)
None
60/180Hz
6 F
30 F
to
36 F
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
Toshiba
E7299
(See note 8)
Type 19
(11001)
LOW SPEED OPERATION ONLY
(See note 1)
60 Hz
N/A
20 F
to
30 F
733317-13
735925-13
906894-13
XH-121
XH-126
XS-AV stator
XS-RA stator
(27.5/58 )
INDICO IQ
DSS PART NO.
(See note 2)
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
904925-23
CMP 200
DSS PART NO.
(See note 2)
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
901297-15
901298-15
(See note 10)
906672-23
904556-13
903255-13
904925-21
904925-22
904925-23 *
* Preferred
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
904556-13
903255-13
904925-21
904925-22
904925-23 *
* Preferred
901297-13
901298-13
906672-21
906672-22
906672-23 *
* Preferred
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
901297-13
901298-13
906672-21
906672-22
906672-23 *
* Preferred
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 29
CPI Canada Inc.
3.0
X-Ray Tube Stator Compatibility Tables
DUAL SPEED STARTER TUBE SELECT TABLE (cont)
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
Switches
(SEE TABLE 3 FOR OPERATING PARAMETERS)
OUTPUT
FREQ.
L.S.
SHIFT
CAP.
INDICO 100
DSS PART NO.
(See note 2)
INDICO IQ
DSS PART NO.
(See note 2)
CMP 200
DSS PART NO.
(See note 2)
Toshiba
E7813
(See note 8)
(1........5)
Type 29
(10111)
H.S.
SHIFT
CAP.
None
60/180 Hz
6 F
30 F
to
36 F
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
E7843
(See note 8)
Type 0
(00000)
LOW SPEED OPERATION ONLY
(See note 1)
60 Hz
N/A
30 F
to
36 F
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
E7861
(See note 8)
Type 19
(11001)
LOW SPEED OPERATION ONLY
(See note 1)
60 Hz
N/A
20 F
to
30 F
733317-13
735925-13
906894-13
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
904556-13
903255-13
904925-21
904925-22
904925-23 *
* Preferred
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
901297-13
901298-13
906672-21
906672-22
906672-23 *
* Preferred
E7864
(See note 8)
Type 17
(10001)
None
60/180 Hz
6 F
30 F
to
36 F
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
E7865
(See note 8)
Type 19
(11001)
LOW SPEED OPERATION ONLY
(See note 1)
60 Hz
N/A
20 F
to
30 F
733317-13
735925-13
906894-13
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
904556-13
903255-13
904925-21
904925-22
904925-23 *
* Preferred
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
901297-13
901298-13
906672-21
906672-22
906672-23 *
* Preferred
XH-106V
XH-180
XS-AL stator
(9.4/28.3 )
Toshiba
XH-121
XS-BA stator
(18/47.5 )
Toshiba
XH-121
XH-126
XH-150
XS-RA stator
(27.5/58 )
Toshiba
XH-112V
XS-AG stator
(9.4/28.3 )
Toshiba
XH-121
XH-126
XS-AV stator
(27.5/58 )
CODE,
OPERATING NOTES
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 30
CPI Canada Inc.
3.0
X-Ray Tube Stator Compatibility Tables
DUAL SPEED STARTER TUBE SELECT TABLE (cont)
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
Switches
(SEE TABLE 3 FOR OPERATING PARAMETERS)
OUTPUT
FREQ.
L.S.
SHIFT
CAP.
INDICO 100
DSS PART NO.
(See note 2)
INDICO IQ
DSS PART NO.
(See note 2)
CMP 200
DSS PART NO.
(See note 2)
Toshiba
XH-112V
XS-AG stator
(9.4/28.3 )
E7869
(See note 8)
(1........5)
Type 17
(10001)
H.S.
SHIFT
CAP.
None
60/180 Hz
6 F
30 F
to
36 F
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
Toshiba
E7876
(See note 8)
Type 19
(11001)
LOW SPEED OPERATION ONLY
(See note 1)
60 Hz
N/A
20 F
to
30 F
733317-13
735925-13
906894-13
Toshiba
XH-121
XH-126
XH-150
XS-AL stator
(9.4/28.3 )
E7884
(See note 8)
Type 29
(10111)
LOW SPEED OPERATION ONLY
(See note 1)
60 Hz
N/A
30 F
to
36 F
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
Toshiba
E7886
(See note 8)
Type 19
(11001)
LOW SPEED OPERATION ONLY
(See note 1)
60 Hz
N/A
20 F
to
30 F
733317-13
735925-13
906894-13
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
904556-13
903255-13
904925-21
904925-22
904925-23 *
* Preferred
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
904556-13
903255-13
904925-21
904925-22
904925-23 *
* Preferred
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
901297-13
901298-13
906672-21
906672-22
906672-23 *
* Preferred
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
901297-13
901298-13
906672-21
906672-22
906672-23 *
* Preferred
XH-121
XS-AV stator
XS-RA stator
(27.5/58 )
XH-121
XS-126
XS-AV stator
XS-RA stator
(27.5/58 )
CODE,
OPERATING NOTES
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 31
CPI Canada Inc.
3.0
X-Ray Tube Stator Compatibility Tables
DUAL SPEED STARTER TUBE SELECT TABLE (cont)
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
Varian/Machlett
Dynamax 52
Std “R” stator
(16/50 )
A-102
A-132
A-142
Varian/Machlett
Dynamax 62
“STD” stator
(23/56 )
Dynamax 62U
configured as
“STD” or “R”
(15/36 )
Varian
B-100
“R” stator
(16/50 )
A-192B
A-196
A-197
Type 0
(00000)
A-256
A-272
A-282
A-292
A-482
Type 1
(10000)
Varian
B-100
“Q” stator
(8/15 )
A-286
Switches
(SEE TABLE 3 FOR OPERATING PARAMETERS)
OUTPUT
FREQ.
(1........5)
Type 0
(00000)
H.S.
SHIFT
CAP.
L.S.
SHIFT
CAP.
INDICO 100
DSS PART NO.
(See note 2)
INDICO IQ
DSS PART NO.
(See note 2)
CMP 200
DSS PART NO.
(See note 2)
None
60/180 Hz
6 F
30 F
to
36 F
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
None
60/180 Hz
6 F
30 F
to
36 F
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
733317-02
735925-02
906894-02
904925-22
901297-02
901298-02
906672-22
CODE,
OPERATING NOTES
A-486
A-102
A-132 / A-134*
A-142 / A-144*
* (See note 9)
A-145
Type 0
(00000)
None
60/180 Hz
6 F
30 F
to
36 F
Type 2
(01000)
LOW SPEED OPERATION ONLY
(See note 1)
60 Hz
N/A
A-102
A-132 / A-134*
A-142 / A-144*
* (See note 9)
Type 11
(11010)
None
60/180 Hz
20 F
30 F
to
36 F
60 F
to
62 F
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 32
CPI Canada Inc.
3.0
X-Ray Tube Stator Compatibility Tables
DUAL SPEED STARTER TUBE SELECT TABLE (cont)
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
Varian
B-130
B-130H
B-135H
B-146
B-147
B-150
B-150H
“R” stator
(16/50 )
A-152
A-182 / A-184*
A-192 / A-194*
A-195
A-196
A-197
* (See note 9)
A-272 / A-274*
A-277 / A-278*
A-282 / A-284 *
A-286
A-292 / A-294*
A-482
G-242 G-256
G-292 / G-294*
G-296
G-892 G-896
* (See note 9)
A-152
A-182 / A-184*
A-192 / A-194*
A-195 / A-196
A-197 / A-252
A-272 / A-274*
A-277 / A-278*
A-282 / A-284 *
A-286
A-292 / A-294*
A-482
G-242 G-256
G-292 / G-294*
G-296
RAD-60
* (See note 9)
Varian
B-130
B-130H
B-135H
B-150
B-150H
“Q” stator
(6/11 )
Switches
(1….....5)
CODE,
OPERATING NOTES
(SEE TABLE 3 FOR OPERATING PARAMETERS)
OUTPUT
FREQ.
60/180 Hz
H.S.
SHIFT
CAP.
6 F
L.S.
SHIFT
CAP.
30 F
to
36 F
INDICO 100
DSS PART NO.
(See note 2)
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
INDICO IQ
DSS PART NO.
(See note 2)
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
CMP 200
DSS PART NO.
(See note 2)
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
Type 0
(00000)
None
None
60/180 Hz
20 F
60 F
to
62 F
733317-02
735925-02
906894-02
904925-22
901297-02
901298-02
906672-22
Type 1
(10000)
Type 12
(00110)
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 33
CPI Canada Inc.
3.0
X-Ray Tube Stator Compatibility Tables
DUAL SPEED STARTER TUBE SELECT TABLE (cont)
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
Switches
(1........5)
Varian
B-160
B-160H
B-165H
“R” Stator
(16/50 )
(SEE TABLE 3 FOR OPERATING PARAMETERS)
OUTPUT
FREQ.
G-1077
G-1078
G-1080
G-1082 / G-1084*
G-1086 / G-1087*
G-1092 / G-1094*
* (See note 9)
G-1582
G-1592
G-1593
Type 15
(11110)
None
Type 15
(11110)
SG-1096
Varian
B-240H
“R” Stator
(14/46 )
Varian (Eureka)
Diamond
LEO
“R” stator
(20/50 )
Varian
B-180
B-180H
B-185
B-185H
“R” Stator
(16/50 )
Varian
B-199
“S” Stator
(15/18 )
CODE,
OPERATING NOTES
60/180 Hz
H.S.
SHIFT
CAP.
6 F
L.S.
SHIFT
CAP.
30 F
to
36 F
INDICO 100
DSS PART NO.
(See note 2)
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
INDICO IQ
DSS PART NO.
(See note 2)
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
CMP 200
DSS PART NO.
(See note 2)
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
None
60/180 Hz
6 F
30 F
to
36 F
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
Type 18
(01001)
None
50/150 Hz
5 F
30 F
904556-13
903255-13
904925-21
904925-22
901297-13
901298-13
906672-21
906672-22
G-2090
Type 6
(01100)
None
100 /
180 Hz
6 F
12.5F
to
20F
733317-13
735925-13
906894-13
733317-17
735925-17
906894-17
733317-16
735925-16
906894-16
904925-21
904925-22
904925-23
RAD-12
Type 0
(00000)
LOW SPEED OPERATION ONLY
(See note 1)
60 Hz
N/A
30 F
to
36 F
RAD-13
RAD-14
RAD-68
Type 0
(00000)
None
60/180 Hz
6 F
30 F
to
36 F
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
901297-16
901298-16
906672-21
906672-22
906672-23
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 34
CPI Canada Inc.
3.0
X-Ray Tube Stator Compatibility Tables
DUAL SPEED STARTER TUBE SELECT TABLE (cont)
TUBE TYPE
(HOUSING)
TUBE TYPE
(INSERT)
Varian (Eureka)
Diamond
Emerald
“R” stator
(20/50 )
Varian (Eureka)
Sapphire
“R” stator
(20/50 )
* For “Q” stator,
refer to B-130
housing
CODE,
OPERATING NOTES
Switches
(1........5)
(SEE TABLE 3 FOR OPERATING PARAMETERS)
RAD-8
RAD-74
Type 0
(00000)
LOW SPEED OPERATION ONLY
(See note 1)
RAD-21
RAD-40
RAD-44
RAD-56
RAD-60 *
RAD-92
RAD-94
Type 5
(10100)
None
OUTPUT
FREQ.
60 Hz
H.S.
SHIFT
CAP.
N/A
L.S.
SHIFT
CAP.
30 F
to
36 F
INDICO 100
DSS PART NO.
(See note 2)
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
60/180 Hz
6 F
30 F
to
36 F
733317-12
735925-12
906894-12
733317-13
735925-13
906894-13
INDICO IQ
DSS PART NO.
(See note 2)
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
904556-12
903255-12
904556-13
903255-13
904925-21
904925-22
904925-23
CMP 200
DSS PART NO.
(See note 2)
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
901297-12
901298-12
901297-13
901298-13
906672-21
906672-22
906672-23
NOTE 1:
Tube types designated as low speed only or high speed only must be programmed for low speed only or high speed only operation. Refer to the section
Tube Selection within Chapter 3 of the applicable generator service manual for details. For some tubes listed as high speed only, the starter may be
capable of low speed operation but the Manufacturer’s data sheet for the Insert lists high speed only. In other cases, the limitation is due to operational
limitations of the Dual Speed Starter itself.
NOTE 2:
Dual Speed Starter part numbers 733317-XX (Indico 100), 904556-XX (Indico IQ) and 901297-XX (CMP 200® DR) are used in 400 VAC 3 generators /
power supplies and in 480 VAC 3 generators / power supplies with a line adjusting transformer.
Dual Speed Starter part numbers 735925-XX (Indico 100), 903255-XX (Indico IQ) and 901298-XX (CMP 200® DR) are used in 230 VAC 1 generators /
power supplies and in 480 VAC 3 direct input generators / power supplies (using no line adjusting transformer).
Dual Speed Starter part numbers 906894-XX (Indico 100), 904925-XX (Indico IQ) and 906672-XX (CMP 200® DR) are used in both 400 VAC and
480 VAC 3 generators. These RoHS-compliant Starters replace the existing 73317-XX / 735925-XX series (Indico 100), 904556-XX / 903255-XX
series (Indico IQ) and 901297-XX / 901298-XX series (CMP 200® DR), and may provide a greater selection of available shift capacitance.
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 35
CPI Canada Inc.
3.0
X-Ray Tube Stator Compatibility Tables
DUAL SPEED STARTER TUBE SELECT TABLE (cont)
Where more than one Dual Speed Starter part number is referenced for a particular tube type, any of these (applicable to the generator and input voltage)
is acceptable. For 2-tube systems using different tube types, both tube types must be considered. Where available, the XXXXXX-21 starter is generally
preferred, unless otherwise indicated in the tables.
The Dual Speed Starters provide a selection of shift capacitance values for both high speed and low speed operation, as identified by the DSS part
number suffix (“tab type”). Unless otherwise specified, capacitor selection is made automatically by relays located on the Dual Speed Starter board.
The following table lists the capacitance values provided, along with applicable notes.
DSS Part No.
(applicability)
XXXXXX-01
(Indico 100 only)
XXXXXX-02
(All except Indico IQ)
XXXXXX-12
(All except Indico IQ)
XXXXXX-13
(All except Indico IQ)
XXXXXX-15
(All except Indico IQ)
HIGH-SPEED SHIFT
CAPACITANCE
LOW-SPEED SHIFT
CAPACITANCE
COMMENTS
6 F
31 F
May be replaced by XXXXXX-21 in all configurations where available.
20 F
40 F
6 F, 7.5 F
36 F, 37.5 F
Typically used to support “Q” stator tubes.
May be replaced by XXXXXX-22 in all configurations, where available.
May be replaced by XXXXXX-21 in all configurations, where available.
5 F, 6 F
30 F
May be replaced by XXXXXX-21 in all configurations, where available.
3 F, 6 F
Typically used to support CGR (GE) Statorix or Toshiba E7252 (XS-R/RA) tubes.
May be replaced by XXXXXX-23 in all configurations, where available.
Manual configuration required; see Note 10.
XXXXXX-16
(All except Indico IQ)
6 F, 12.5 F
15.5 F, 18.5 F
or 28 F, 31 F
(manually selected)
12.5 F, 31.5 F, 37.5 F
XXXXXX-17
(Indico 100 only)
5 F, 12.5 F
30 F, 37.5 F
XXXXXX-21
(All except Indico 100)
5 F, 6 F, 7.5 F,
12.5 F
5 F, 6 F, 20 F
12.5 F, 30 F, 37.5 F
3 F, 6 F, 12.5 F
23 F, 32.5 F
XXXXXX-22
(All except Indico 100)
XXXXXX-23
(All except Indico 100)
20 F, 30 F, 62.5 F
Used to support Philips ROT350/500 tubes. May be used in place of Dual Speed
Starters “-12” or “-13” in two-tube systems that include both a standard “R” stator
tube (6 F high speed shift capacitance) and a Philips ROT 350/500 tube.
All such configurations may be replaced by XXXXXX-21, where available.
Used in place of Dual Speed Starter “-13” in two-tube systems that include both a
standard “R” stator tube (6 F of high speed shift capacitance) and an IAE tube
(5 F of high speed shift capacitance). All such configurations may be replaced by
XXXXXX-21, where available. Do not use these starters in place of XXXXXX-13
with Siemens tubes due to high-speed shift capacitor voltage limitations.
Generally preferred where available, unless otherwise indicated within the tables.
Typically used to support “Q” stator tubes.
Preferred over XXXXXX-02, where available.
Typically used to support CGR (GE) Statorix or Toshiba E7252 (XS-R/RA) tubes.
Preferred over XXXXXX-15, where available.
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 36
CPI Canada Inc.
3.0
X-Ray Tube Stator Compatibility Tables
DUAL SPEED STARTER TUBE SELECT TABLE (cont)
NOTE 3:
Comet tube inserts with the prefix “DI” and “DX” are interchangeable.
NOTE 4:
Philips / Dunlee housing with the windings connected in series (low-speed / high impedance configuration).
NOTE 5:
Philips / Dunlee housing with the windings connected in parallel (high-speed / low impedance configuration).
NOTE 6:
Dunlee tube inserts with the prefix “DU” and Philips tube inserts with the prefix “RO” are interchangeable. Select the corresponding Philips insert type
within the Generator software if the Dunlee type is not available.
NOTE 7:
Siemens (SXVT) housing with the “phase-shifted” windings connected in parallel (low impedance, high speed configuration).
NOTE 8:
Complete Toshiba x-ray tube assemblies include the suffix “X, “FX”, “GX”, or “JX”, which are interchangeable with respect to rotor and anode
characteristics.
NOTE 9:
These X-ray tubes incorporate a control grid. Grid control is currently not supported by CPI generators. Connect the grid connection to Ground when
using these tubes, and select the insert type within the Generator software corresponding to the equivalent non-grid tube.
NOTE 10:
Dual Speed Starters 733317-15 / 735925-15 / 906894-15 (Indico 100) and 901297-15 / 901298-15 (CMP 200® DR) have jumper selectable phase shift
capacitance that allows selection of 15.5 F or 28 F low speed shift capacitors for operation with CGR (GE) Statorix or Toshiba E7252 (XS-R/RA stator)
tubes, respectively, as per table 2. By default, this starter is factory set to the 28 F position. Confirm proper configuration per the section
“Configuring Dual Speed Starter XXXXXX-15” in chapter 2 before proceeding. These starters also support standard “R” stators that require 6 F of
high speed shift capacitance.
(Indico 100 only): If configured for 28 F of low speed capacitance, these Dual Speed Starters also support tubes listed in Table 2 as requiring Dual
Speed Starters 733317-13 / 735925-13 / 906894-15 and requiring 6 F of high speed capacitance. For two-tube operation, this configuration will support:
a) These tubes and the Toshiba E7252/XS-RA (high and low speed) simultaneously, or;
b) These tubes and a CGR Statorix tube (high-speed only) simultaneously.
c) The Toshiba E7252/XS-RA and a CGR tube simultaneously if one or both of these tubes is operated in high-speed mode only.
(CMP 200® DR only): If configured for 28 F of low speed capacitance, these Dual Speed Starters also support tubes listed in Table 2 as requiring Dual
Speed Starters 901297-13 / 901298-13 and requiring 6 F of high speed capacitance.
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 37
CPI Canada Inc.
3.1
X-Ray Tube Stator Compatibility Tables
DUAL SPEED STARTER (and INDICO IQ LOW SPEED STARTER) TUBE CODES
Tube operating parameters for each tube type are selected by setting switches to the applicable Code, as indicated in Table 1 (Indico IQ LSS) and
Table 2 (DSS). For reference, operating parameters applicable to each Code are contained in Table 3 below.
Reference notes are provided at the end of Table 3.
TABLE 3: TUBE TYPE CODES (DUAL SPEED STARTER and INDICO IQ LOW SPEED STARTER)
TUBE
TYPE
(CODE)
Switches
(1........5)
H.S.
START
VOLTS
H.S.
RUN
VOLTS
H.S.
BOOST
TIME
H.S.
FREQ.
H.S.
BRAKE
VOLTS
H.S.
BRAKE
TIME
L.S.
START
VOLTS
L.S.
RUN
VOLTS
L.S.
BOOST
TIME
L.S.
FREQ.
Hz
H.S.
SHIFT
CAP.
APPLICABLE
DSS TYPES
(See note 1)
0
00000
400 V
100 V
1.4 sec
180 Hz
100 V
3.0 sec
240 V
60 V
1.4 sec
60 Hz
6 F
-12, -13, -15, -16, -21, -22, -23
1
10000
400 V
100 V
1.9 sec
180 Hz
100 V
3.0 sec
240 V
70 V
1.9 sec
60 Hz
6 F
-12, -13, -15, -16, -21, -22, -23
2
01000
400 V
100 V
1.0 sec
180 Hz
100 V
3.0 sec
240 V
60 V
1.0 sec
60 Hz
6 F
-12, -13, -15, -16, -21, -22, -23
3
11000
400 V
100 V
5.0 sec*
180 Hz
150 V
3.0 sec
240 V
70 V
5.0 sec
60 Hz
6 F
-12, -13, -15, -16, -21, -22, -23
* ( 2.5 sec Ready)
4
00100
420 V
70V
2.5 sec
180 Hz
170 V
3.0 sec*
240 V
50 V
1.6 sec
60 Hz
6 F
-12, -13, -15, -16, -21, -22, -23
* (LS braking 0.8 sec)
5
10100
400 V
100 V
2.3 sec
180 Hz
100 V
3.0 sec
240 V
50 V
2.3 sec
60 Hz
6 F
-12, -13, -15, -16, -21, -22, -23
-16, -21,
* ( 5.0 sec Ready)
-22, -23
** (LS braking 2.0s)
*** (12.5F-20F L.S. cap.)
CODE
6
01100
440 V
140 V
6.0 sec*
180 Hz
250 V
4.0 sec**
400 V
110 V
5.0 sec
100 Hz
6 F ***
7
11100
240 V
120 V
2.3 sec
180 Hz
100 V
3.0 sec
240 V
50 V
2.3 sec
60 Hz
6 F
-12, -13, -15, -16, -21, -22, -23
8
00010
400 V
90 V
3.0 sec
150 Hz
100 V
3.0 sec
240 V
100 V
1.5 sec
50 Hz
6 F
-12, -13, -15, -16, -21, -22, -23
9
10010
280 V
60 V
1.5 sec
180 Hz
80 V
3.0 sec
180 V
50 V
1.5 sec
60 Hz
12.5 F
-12 (LS only), -16, -17, -21, -23,
-22 (LS only)
10
01010
440 V
100 V
0.8 sec
150 Hz
120 V
1.8 sec
220 V
50 V
0.6 sec
50 Hz
6 F
-12, -13, -15, -16, -21, -22, -23
11
11010
290 V
70 V
0.8 sec
180 Hz
60 V
3.0 sec
150 V
50 V
0.8 sec
60 Hz
20 F
-02, -22
12
00110
290 V
60/80V
1.3 sec
180 Hz
60 V
3.0 sec
150 /
180 V
50 V
1.3 sec
60 Hz
20 F
-02, -22
13
10110
340 V
60 V
1.0 sec
180 Hz
100 V
3.0 sec
240 V
70 V
1.0 sec
60 Hz
20 F
-02, -22
14
01110
400 V
90 V
0.9 sec
180 Hz
80 V
2.0 sec
230 V
70 V
0.9 sec
60 Hz
7.5 F
-12, -21
15
11110
400 V
100 V
5.0 sec
180 Hz
150 V
3.0 sec
240 V
70 V
5.0 sec
60 Hz
6 F
-12, -13, -15, -16, -21, -22, -23
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 38
CPI Canada Inc.
3.1
X-Ray Tube Stator Compatibility Tables
DUAL SPEED STARTER (and INDICO IQ LOW SPEED STARTER) TUBE CODES (cont)
TUBE
TYPE
(CODE)
Switches
(1........5)
H.S.
START
VOLTS
H.S.
RUN
VOLTS
H.S.
BOOST
TIME
H.S.
FREQ.
H.S.
BRAKE
VOLTS
H.S.
BRAKE
TIME
L.S.
START
VOLTS
L.S.
RUN
VOLTS
L.S.
BOOST
TIME
L.S.
FREQ.
Hz
H.S.
SHIFT
CAP.
APPLICABLE
DSS TYPES
(See note 1)
16
00001
340 V
80 V
1.6 sec
180 Hz
80 V
3.0 sec
150 V
50 V
1.6 sec
60 Hz
5 F
-13, -17, -21, -22, -23 (LS only)
17
10001
320 V
80 V
2.3 sec
180 Hz
100 V
3.0 sec
200 V
50 V
1.5 sec
60 Hz
6 F
-12, -13, -15, -16, -21, -22, -23
18
01001
400 V
100 V
2.8 sec
150 Hz
120 V
3.0 sec
180 V
60 V
1.5 sec
50 Hz
5 F
-13, -17, -21, -22, -23 (LS only)
19
11001
320 V
130 V
2.0 sec
180 Hz
130 V
3.0 sec
240 V
60 V
1.4 sec
60 Hz
3 F
-12, -13, -16, -21,-22 (all LS only),
-15, -23
20
00101
400 V
90 V
1.0 sec
180 Hz
80 V
3.0 sec
230 V
70 V
1.0 sec
60 Hz
7.5 F
-12, -21
21
10101
420 V
100 V
2.2 sec
180 Hz
150 V
3.0 sec
240 V
80 V
1.8 sec
60 Hz
6 F
-12, -13, -15, -16, -21, -22, -23
22
01101
340 V
60 V
1.4 sec
150 Hz
120 V
4.0 sec
220 V
60 V
1.5 sec
50 Hz
6 F
-12, -13, -15, -16, -21, -22, -23
23
11101
360 V
90 V
1.6 sec
150 Hz
80 V
3.0 sec
150 V
50 V
1.6 sec
50 Hz
5 F
-13, -21, -22, -23 (LS only)
24
00011
420 V
80 V
1.8 sec
150 Hz
150 V
3.0 sec
240 V
80 V
1.8 sec
50 Hz
6 F
-12, -13, -15, -16, -21, -22, -23
25
10011
420 V
80 V
2.2 sec
150 Hz
150 V
3.0 sec
240 V
80 V
1.8 sec
50 Hz
6 F
-12, -13, -15, -16, -21, -22, -23
26
01011
400 V
80 V
1.0 sec
150 Hz
120 V
3.0 sec
240 V
80 V
1.0 sec
50 Hz
5 F
Reserved
27
11011
440 V
100 V
1.1 sec
150 Hz
120 V
1.8 sec
220 V
80 V
1.1 sec
50 Hz
5 F
-13, -17, -21, -22, -23 (LS only)
28
00111
450 V
150 V
3.0 sec
150 Hz
120 V
3.0 sec
240 V
90 V
3.0 sec
50 Hz
3 F
-15, -21 (LS only), -23
29
10111
240 V
60 V
2.2 sec
180 Hz
80 V
1.6 sec
130 V
50 V
1.3 sec
60 Hz
6 F
-12, -13, -15, -16, -21, -22, -23
30
01111
420 V
50 V
1.8 sec
180 Hz
150 V
3.0 sec*
240 V
50 V
1.8 sec
60 Hz
12.5 F
-16, -17, -21, -23
* (LS braking 1.2 sec)
31
11111
330V
80 V
1.4 sec
180 Hz
70V
3.0 sec
240 V
80 V
1.4 sec
60 Hz
5 F
-13, -21, -22, -23 (LS only)
CODE
THE STARTER USES MODULATION STRATEGIES TO OBTAIN THE DESIRED OUTPUTS. MEASURED VOLTAGES MAY NOT AGREE WITH THOSE LISTED
IN THE TABLE. HOWEVER, THE CURRENTS FLOWING IN THE STATOR WINDINGS ARE EQUIVALENT TO THOSE THAT WOULD EXIST IF THE STATOR
WAS EXCITED WITH THESE VOLTAGES.
NOTE 1:
Tube Type codes should only be used with the applicable DSS types specified in this table (refer to Table 1 for applicable DSS Types).
Refer to Table 1 for Indico IQ LSS Part Numbers applicable to each Tube Type (Housing and Insert).
Refer to Table 2 for DSS Part Numbers applicable to each Tube Type (Housing and Insert).
Use and disclosure is subject to the restrictions on the title page of this CPI document.
X-Ray Generator Service Manual Supplement
746026
Rev. AD
Page 39