Panel Mount Datasheet DC60 Series Normally Closed Output, AC Control Input • AC Control • Epoxy Free Design let e • Ratings from 3A to 7A @ 60 VDC • Bi-polar transistor output • UL Approved, CE Compliant to EN60950-1 • Improved SEMS screw and washer • Redesigned housing with anti-rotation barriers For Generation 3 datasheet click here PRODUCT SELECTION Control Voltage 90-280 VAC/VDC AVAILABLE OPTIONS Series * 5A 7A DC60SA5-B DC60SA7-B Termination Blank: Screws & clamps K: Installed standoffs with Output Type screws for PC Board -B: Normally Closed mounting (1) Control Voltage SA: 90-280 VAC/DC SA 3 K Rated Load Current 3: 3 Amps 5: 5 Amps 7: 7 Amps H -B Thermal Pad Blank: Not Included H: Included so DC60 3A DC60SA3-B Required for valid part number For options only and not required for valid part number Not all part number conbinations are available. Contact Crydom Technical Support for information on the availability of a specific part number. OUTPUT SPECIFICATIONS (2) Description Recommeded Operating Voltage [Vdc] Absolute Maximum Rating [Vdc] Ob Maximum Off-State Leakage Current @ Rated Voltage [mA] Maximum Load Current [Adc] (3) Minimum Load Current [mA] Maximum Surge Current (10 msec)[Adc] Maximum On-State Voltage Drop @ Rated Current [Vdc] Thermal Resistance Junction to Case (Rjc) [°C/W] Minimum heat sink @ Ambient (for max current= °C/W & Ta) 3A 5A 7A 3-48 60 0.1 3 20 6 1 2 5 @ 60°C 3-48 60 0.1 5 20 10 1.2 2 5 @ 60°C 3-48 60 0.1 7 20 14 1.3 2 5 @ 40°C INPUT SPECIFICATIONS (2) Description Control Voltage Range Maximum Reverse Voltage Must Turn-Off Voltage Maximum Turn-On Voltage Minimum Input Current (for on-state) Maximum Input Current Nominal Input Impedance [Ohms] Maximum Turn-On Time [µsec] Maximum Turn-Off Time [µsec] Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice. AC Control 90-280 VAC/VDC 90 VAC/VDC 10 VAC/VDC 2 mA 5.5 mA 60K 300 100 Panel Mount Datasheet GENERAL SPECIFICATIONS (2) Description Parameters WIRING DIAGRAM * Inductive loads must be diode suppresed. + + - Load V + * Load * 4000 Vrms 109 Ohm 8 pF -30 to 80°C -40 to 125 °C 2.46 oz (70 g) UL94 V-0 Aluminum 13-15 /1.5-1.7 18-20 / 2-2.2 18-20 / 2-2.2 w/”K” option 8-10 / 0.9-1.13 85% non-condensing 21,395,130 hours (2,441 years) 11,545,504 hours (1,317 years) let e Dielectric Strength, Input/Output/Base (50/60Hz) Minimum Insulation Resistance (@ 500 VDC) Maximum Capacitance, Input/Output Ambient Operating Temperature Range Ambient Storage Temperature Range Weight (typical) Housing Material Baseplate Material Input Terminal Screw Torque Range (in-lb/Nm) Load Terminal Screw Torque Range (in-lb/Nm) SSR Mounting Screw Torque Range (in-lb/Nm) Input/Load Terminal Screw Torque Range (in-lb/Nm) (1) Humidity MTBF (Mean Time Between Failures) at 40°C ambient temperature (4) MTBF (Mean Time Between Failures) at 60°C ambient temperature (4) V - + Recommended Wire Sizes Wire Size (Solid / Stranded) Terminals 2 OUTPUT S O L I D S TAT E R E L AY 4 +3 INPUT + V - +1 OUTPUT Input 2 so +1 S O L I D S TAT E R E L AY 4 +3 INPUT Output Wire Pull-Out Strength (lb)[N] 24 AWG (0.2 mm2) / 0.2 [minimum] 10 [44.5] 2 x 12 AWG (3.3 mm2) / 3.3 [maximum] 90 [400] 20 AWG (0.5 mm2) / 0.518 [minimum] 30 [133] 2 x 10 AWG (5.3 mm2) / 5.3 110 [490] 2 x 8 AWG (8.4 mm2) / 8.4 [maximum] 90 [400] + V - Ob EQUIVALENT CIRCUIT BLOCK DIAGRAMS Input Current vs Input Voltage Standard Regulated AC Input 5 4.5 3 INPUT AC/DC AC/DC 4 AC/DC Converter 1 +DC Trigger Circuit 2 Do not forget to visit us at: www.crydom.com -DC Copyright © 2016 Crydom Inc. Specifications subject to change without notice. Input Current (mA) DC60 Series AC Control 4 3.5 3 2.5 2 1.5 1 0.5 0 0 50 100 150 AC Input Voltage 200 250 300 Panel Mount Datasheet MECHANICAL SPECIFICATIONS (2) Tolerances: ±0.02 in / 0.5 mm All dimensions are in: inches [millimeters] Screw Termination +1 1.88 [47.6] 2 OUTPUT 4 INPUT 1.0 [25.4] 1.75 [44.5] GENERAL NOTES +1 1.7 [43.2] S O L I D S TAT E R E L AY +3 1.1 [27.9] 0.49 [12.4] 0.89 [22.6] Mounting Hole/Slot 0.19 [4.9] DIA. Mounting Hole/Slot 0.19 [4.9] DIA. 1.04 [26.4] (2 places) let e 1.1 [27.9] 0.49 [12.4] Hex Standoff Termination (“K” Option) (1) 2.25 [57.3] 1.88 [47.6] OUTPUT 2 1.7 [43.2] S O L I D S TAT E R E L AY 4 INPUT +3 1.0 [25.4] 1.75 [44.5] so (1) Option “K” is designed and tested for use with printed circuit boards or ring/fork terminals having a thickness between 0.031 and 0.093 inches (0.79 to 2.36 mm). (2) All parameters at 25°C unless otherwise specified. (3) Heat sinking required, see derating curves. (4) All parameters at 50% power rating and 100% duty cycle (contact Crydom tech support for detailed report). (5) For single surge pulse Tc=25°C; Tj=150°C. Ob For additional information or specific questions, contact Crydom Technical Support. Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice. 0.93 [23.6] (4 places) 1.0 [25.4] (2 places) 2.25 [57.3] Panel Mount Datasheet SURGE CURRENT INFORMATION DC60SA3-B 10 5 0.1 1 10 100 Surge Duration (msec) Surge Current (Amp) 10 5 0 1000 0.1 1 10 Surge Duration (msec) 100 1000 DC60SA7-B 20 15 10 5 0 15 let e 15 0 DC60SA5-B 20 Surge Current (Amp) 20 Surge Current (Amp) Single Pulse (5) 0.1 10 Surge Duration (msec) 100 so THERMAL DERATE INFORMATION 1 1000 (i) SSR metal base plate acting as heat sink, it must be exposed to free ambient air. DC60SA3-B 5°C/W 2.5 Load Current (Amps) Load Current (Amps) 3 2 1.5 1 0.5 Ob 0 20 30 40 DC60SA5-B 5°C/W No Heat Sink(i) 50 60 70 80 4 3 2 1 0 20 30 Ambient Temperature (ºC) DC60SA7-B 5°C/W No Heat Sink(i) Load Current (Amps) 6 5 4 3 2 1 20 30 40 50 60 Ambient Temperature (ºC) 7 0 No Heat Sink(i) 5 40 50 60 Ambient Temperature (ºC) Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice. 70 80 70 80 Panel Mount Datasheet AGENCY APPROVALS EN60950-1: Meets the requirements of sections1.5: 1,7: 2.9: 2.10.5.3: 4.2: 4.5: 4.7: ACCESORIES New Accessories! Protective Cover & Hardware Kits Protective Cover Part number: KS101 let e E116950 Hardware Kit Part number: HK4 Cover Hardware Kit Heat Sink Part No. KS101 HK1 HS501DR 5.0 TRM1 HSP-1 HK4 HS301 / HS301DR 3.0 TRM6 HSP-2 HS251 2.5 HS201 / HS201DR 2.0 HS202 / HS202DR 2.0 HS172 1.7 HS151 / HS151DR 1.5 HS122 / HS122DR 1.2 HS103 / HS103DR 1.0 HS101 1.0 HS073 0.7 HS072 0.7 HS053 0.5 HS033 0.36 HS023 0.25 so Clear plastic cover compatible with all new S1 designs. Safety covers provide added protection from electric shock when installing or checking equipment. Recommended Accessories Ob Bag with 2 square brass accessories and 2 screw 8-32 x 5/8 for output. Used to mount TMR1 lug terminals. Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice. Thermal Resistance Lug Terminal Thermal Pad [ºC/W] Rev. 060216 Panel Mount Datasheet DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险 • Verify all connections and replace all covers before turning on power. • Desconectar todos los suministros de energia a este equipo antes de trabajar con este equipo. • Verificar todas las conexiones y colocar todas las tapas antes de energizer el equipo. El incumplimiento de estas instrucciones puede provocar la muerte o lesiones serias. RISQUE DE DESCHARGE ELECTRIQUE OU EXPLOSION • Eteindre toutes les sources d'énergie de cet appareil avant de travailler dessus de cet appareil GEFAHR EINES ELEKTRISCHE N SCHLAGES ODER EINER EXPLOSION. • Stellen Sie jeglichen Strom ab, der dieses Gerät versorgt, bevor Sie an dem Gerät Arbeiten durchführen • Vérifier tous connections, et remettre tous couverts en olace avant de mettre sous De non-suivi de ces instructions provoquera la mort ou des lésions sérieuses sérieuses. • Vor dem Drehen auf Energie alle Anschlüsse überprüfen und alle Abdeckungen ersetzen. Unterlassung dieser Anweisungen können zum Tode oder zu schweren Verletzungen führen. so Failure to follow these instructions will result in death or serious injury. RIESGO DE DESCARGA ELECTRICA O EXPLOSION. RISCHIO DI SCOSSA ELETTRICA O DELL’ESPLOSIONE. • Spenga tutta l'alimentazione che fornisce questa apparecchiatura prima di lavorare a questa apparecchiatura 存在电击、 爆炸或电弧 闪烁危险 • 在操作此设 备之前请先 关闭电源。 let e HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH. • Disconnect all power before installing or working with this equipment. 若不遵守这些说明， 可能会导致严重的 人身伤害甚至死亡。 • Verificare tutti i collegamenti e sostituire tutte le coperture prima dell’accensione L'omissione di queste istruzioni provocherà la morte o lesioni serie WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告 RISQUE DE DOMMAGE MATERIEL ET DE SURCHAUFFE DU BOITIER GEFAHR VON MATERIALSCHÄDEN UND GEHÄUSEERHITZUNG • The product's side panels may be hot, allow the product to cool before touching. • Follow proper mounting instructions including torque values. • Do not allow liquids or foreign objects to enter this product. • Les panneaux latéraux du produit peuvent être chauds. Laisser le produit refroidir avant de le toucher. • Respecter les consignes de montage, et notamment les couples de serrage. • Ne pas laisser pénétrer de liquide ni de corps étrangers à l'intérieur du produit. • Die Seitenwände können heiß sein. Lassen Sie das Produkt abkühlen, bevor Sie es berühren. • Beachten Sie die Montageanweisungen, • Führen Sie keine Flüssigkeiten oder Fremdkörper in das Produkt ein. Ob RISK OF MATERIAL DAMAGE AND HOT ENCLOSURE Le non-respect de cette directive peut entraîner, Failure to follow these instructions can result in des lésions corporelles graves ou des serious injury, or equipment damage. dommages matériels. Die Nichtbeachtung dieser Anweisung kann Körperverletzung oder Materialschäden zur Folge haben. RIESGO DE DAÑOS MATERIALES Y DE SOBRECALENTAMIENTO DE LA UNIDAD RISCHIO DI DANNI MATERIALI E D'INVOLUCRO CALDO 材料损坏和高温外壳的危险性 • Los paneles laterales del producto pueden estar calientes. Esperar que el producto se enfríe antes de tocarlo. • Respetar las instrucciones de montaje, y en particular los pares de apretado. • No dejar que penetren líquidos o cuerpos extraños en el producto. • I pannelli laterali dell'apparecchio possono scottare; lasciar quindi raffreddare il prodotto prima di toccarlo. • Seguire le istruzioni di montaggio corrette. • Non far entrare liquidi o oggetti estranei in questo apparecchio. Si no se respetan estas precauciones pueden producirse graves lesiones, daños materiales. La mancata osservanza di questa precauzione può causare gravi rischi per l'incolumità personale o danni alle apparecchiature. Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice. • 产品的一侧面板可能很热，在其冷却前请 不要触碰。 • 遵照正确的安装说明，包括扭矩值。 • 请勿让液体及其他异物进入本产品。 如不能正确执行这些操作说明， 极有可能造成严重人体伤害或者设备的损坏。 Panel Mount Datasheet ANNEX - ENVIROMENTAL INFORMATION The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products. Part Name Lead (Pb) let e Toxic or hazardous Substance and Elements Mercury (Hg) Semiconductor die Solder 附件 - 环保信息 Cadmium (Cd) Hexavalent Chromium (Cr (VI)) Polybrominated biphenyls (PBB) Polybrominated diphenyl ethers (PBDE) 此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006, 电子信息产品污染控制标识要求。 铅 汞 (Pb) (Hg) 镉 有毒有害物质或元素 六价铬 多溴联苯 多溴二苯醚 (Cd) (Cr (VI)) (PBDE) so 部件 名称 Ob 半导体芯片 焊接点 50 Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice. (PBB)