CLD-DS26 Rev 8C Product family data sheet Cree® XLamp® MP-L EasyWhite® LEDs Product Description FEATURES Table of Contents The XLamp® MP-L EasyWhite® LED • Cree EasyWhite color temperatures Characteristics.........................................2 eliminates traditional chromaticity binning • High lumen density Flux Characteristics.................................2 and maximizes lumen density, enabling • Wide viewing angle: 125° Relative Spectral Power Distribution......3 luminaire and bulb retrofit manufacturers • Minimum 80 CRI at 2700 K and Electrical Characteristics.........................3 to deliver consistent color and required 3000 K CCT Relative Luminous Flux vs Current and light output to the target end user. XLamp • Electrically neutral thermal path Solder Point Temperature........................4 MP-L EasyWhite LEDs can reduce LED- • RoHS- and REACh‑compliant Typical Spatial Distribution......................4 to-LED color variation to within a 2-step • UL® recognized component Reflow Soldering Characteristics............5 MacAdams ellipse around the desired (E349212) Bin and Order-Code Format.....................6 color temperature, which is 94% smaller Performance Groups – Brightness.........7 than the total area of the corresponding Performance Groups – Chromaticity......7 ANSI C78.377 color region. The XLamp MP-L EasyWhite LED is the perfect choice for lighting applications where high luminous flux output is required from a single, small point source. Applications • Commercial/residential directional lighting • LED retrofit bulbs • General indoor/outdoor illumination Cree EasyWhite® Color Temperatures Plotted on the 1931 CIE Curve................8 Standard Order Codes and Bins..............9 Mechanical Dimensions........................12 Tape and Reel.........................................13 Packaging...............................................14 Examples of specific applications include: commercial/retail display spotlights, LED retrofit bulbs, and other indoor general www.cree.com/Xlamp illumination applications. Copyright © 2010-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 1 XLamp ® MP-L EasyWhite ® LED Characteristics Characteristics Unit Solder Point Temperature Minimum Typical °C Viewing Angle (FWHM) - white 110 degrees 125 mV/°C -30 Temperature Coefficient of Voltage (per LED string) Maximum ESD Classification (HBM per Mil-Std-883D) Class 2 Total Power, all strings @ 150 mA W 11.3 Total Power, all strings @ 250 mA W 19.9 DC Forward Current, per LED string mA 250 Reverse Current, per LED string mA 0.1 Forward Voltage @ 150 mA, per LED string V 25.0 26.0 Forward Voltage @ 250 mA, per LED string V 26.5 27.5 Flux Characteristics @ 150 mA (TJ = 25 °C) The following table provides several base order codes for XLamp MP-L EasyWhite LEDs. For additional order codes, as well as a complete description of the order-code nomenclature, please reference pages 6 through 9 of this document. Color CCT Range 4000 K 3500 K EasyWhite 4-Step 3000 K 2700 K Color CCT Range 4000 K 3500 K EasyWhite 2-Step 3000 K 2700 K Minimum Luminous Flux (lm) Order Code Group Flux (lm) D0 900 MPLEZW-A1-0000-0000D040F E0 1000 MPLEZW-A1-0000-0000E040F B0 700 MPLEZW-A1-0000-0000B035F C0 800 MPLEZW-A1-0000-0000C035F B0 700 MPLEZW-A1-0000-0000B030F C0 800 MPLEZW-A1-0000-0000C030F B0 700 MPLEZW-A1-0000-0000B027F C0 800 MPLEZW-A1-0000-0000C027F Minimum Luminous Flux (lm) Order Code Group Flux (lm) D0 900 MPLEZW-A1-0000-0000D040H E0 1000 MPLEZW-A1-0000-0000E040H B0 700 MPLEZW-A1-0000-0000B035H C0 800 MPLEZW-A1-0000-0000C035H B0 700 MPLEZW-A1-0000-0000B030H C0 800 MPLEZW-A1-0000-0000C030H B0 700 MPLEZW-A1-0000-0000B027H C0 800 MPLEZW-A1-0000-0000C027H Notes: • Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements. See the Measurements section (page 10). • Minimum CRI for EasyWhite color temperatures 27F, 27H, 30F, 30H is 80. • Minimum CRI for EasyWhite color temperatures 35F, 35H, 40F, 40H is 77. • Typical CRI for EasyWhite color temperatures 35F, 35H, 40F, 40H is 80. Copyright © 2010-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 2 XLamp ® MP-L EasyWhite ® LED Relative Spectral Distribution (Ifper = 150 Relative Spectral Power Power Distribution (IF = 150 mA LED) The following graph represents typical spectral output of the XLamp MPL-EZW LED. mA) The following graph represents typical spectral output of the XLamp MP-L EasyWhite LED with all LEDs on simultaneously. Relative Radiant Power (%) 100 80 60 40 20 0 380 430 480 530 580 630 680 730 780 Wavelength (nm) Electrical Characteristics (Tj Electrical Characteristics (TJ = 25 °C) = 25ºC) The following graph represents typical electrical characteristics of each of the three individual strings of the XLamp MPL-EZW LED. The following graph represents typical electrical characteristics of an individual string of XLamp MP-L EasyWhite LEDs. 250 Forward Current (mA) 200 150 100 50 0 18.0 19.0 20.0 21.0 22.0 23.0 24.0 25.0 26.0 27.0 Forward Voltage (V) Copyright © 2010-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 3 XLamp ® MP-L EasyWhite ® LED Relative Luminous Flux vs Current and Solder Point Temperature (Steady‑State Conditions) The data below is representative of the XLamp MP-L EasyWhite LED in steady-state operation with all strings driven equally at the current shown. The relative luminous flux is shown as a percentage of the light output under pulsed test conditions (t=20 ms, If=150 mA, Tsp=Tj=25 °C). The XLamp MP-L EasyWhite LED is binned under these pulsed test conditions. 135 130 125 120 115 110 Luminous Flux, Relative to Pulsed (%) 105 100 95 90 85 80 75 70 150 mA 65 60 200 mA 55 250 mA 50 45 40 35 30 25 20 15 10 5 0 5 15 25 35 45 55 65 75 85 95 105 115 Steady-State Solder Point Temperature (°C) Typical Spatial Radiation Pattern (If = 150 mA) following Distribution graph represents typical output of the XLamp MPL-EZW LED. Typical The Spatial 120 Relative Luminous Intensity (%) 100 80 60 40 20 -90 -60 -30 0 0 30 60 90 Angle (º) Copyright © 2010-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 4 XLamp ® MP-L EasyWhite ® LED Reflow Soldering Characteristics In testing, Cree has found XLamp MP-L EasyWhite LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of the solder paste used. Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment. tP TP Critical Zone TL to TP Temperature Ramp-up TL tS Tsmax Tsmin Ramp-down ts Preheat 25 t 25˚C to Peak Profile Feature Average Ramp-Up Rate (Tsmax to Tp) IPC/JEDEC J-STD-020C Time Lead-Free Solder 1.2 °C/second Preheat: Temperature Min (Tsmin) 120 °C Preheat: Temperature Max (Tsmax) 170 °C Preheat: Time (tsmin to tsmax) 65-150 seconds Time Maintained Above: Temperature (TL) Time Maintained Above: Time (tL) 217 °C 45-90 seconds Peak/Classification Temperature (Tp) 235 - 245 °C Time Within 5 °C of Actual Peak Temperature (tp) 20-40 seconds Ramp-Down Rate 1 - 6 °C/second Time 25 °C to Peak Temperature 4 minutes max. Note: All temperatures refer to the topside of the package, measured on the package body surface. Copyright © 2010-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 5 XLamp ® MP-L EasyWhite ® LED Bin and Order-Code Format Bin codes and order codes are configured in the following manner: Order Code Bin Code Series MPL = MP-L Series MPL = MP-L Version number Version number Kit number Flux code SSSCCC-BB-HHHH-NNNNNNNNN SSSCCC-BB-NNN-FF-HH-HHHH Internal code Internal code Color EZW = EasyWhite Chromaticity code Color EZW = EasyWhite Copyright © 2010-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 6 XLamp ® MP-L EasyWhite ® LED Performance Groups – Brightness XLamp MP-L EasyWhite LEDs are tested for luminous flux and placed into one of the following luminous-flux groups: Group Code Minimum Luminous Flux @ 150 mA per string (lm) Maximum Luminous Flux @ 150 mA per string (lm) A0 600 700 B0 700 800 C0 800 900 D0 900 1000 E0 1000 1100 F0 1100 1200 Performance Groups – Chromaticity XLamp MP-L EasyWhite LEDs are tested for chromaticity and placed into one of the regions defined by the following bounding coordinates. EasyWhite Color Temperatures – 4-Step Code 40F 35F 30F 27F CCT 4000 K 3500 K 3000 K 2700 K EasyWhite Color Temperatures – 2-Step x y x y 0.3744 0.3685 0.3784 0.3741 0.3782 0.3837 0.3804 0.3818 0.3912 0.3917 0.3867 0.3857 0.3863 0.3758 0.3844 0.3778 0.3981 0.3800 0.4030 0.3857 0.4040 0.3966 0.4061 0.3941 0.4186 0.4037 0.4132 0.3976 0.4116 0.3865 0.4099 0.3890 0.4242 0.3919 0.4291 0.3973 0.4322 0.4096 0.4333 0.4062 0.4449 0.4141 0.4395 0.4084 0.4359 0.3960 0.4351 0.3994 0.4475 0.3994 0.4528 0.4046 0.4573 0.4178 0.4578 0.4138 0.4695 0.4207 0.4638 0.4152 0.4589 0.4021 0.4586 0.4060 Code 40H 35H 30H 27H CCT 4000 K 3500 K 3000 K 2700 K Copyright © 2010-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 7 XLamp ® MP-L EasyWhite ® LED Cree EasyWhite® Color Temperatures Plotted on the 1931 CIE Curve 0.45 2700 K ANSI C78.377 Quadrangle EasyWhite "F" (4-Step) Chromaticity Regions 0.44 3000 K 0.43 3500 K 0.42 4000 K CCy 0.41 4500 K 27F 0.40 30F 0.39 35F 0.38 40F 0.37 0.36 0.45 0.43 3000 K 3500 K 0.42 4000 K 0.41 27H 4500 K 30H 0.40 CCy 0.49 2700 K ANSI C78.377 Quadrangle EasyWhite "H" (2-Step) Chromaticity Regions 0.44 0.48 0.47 0.46 0.45 0.44 CCx 0.43 0.42 0.41 0.40 0.39 0.38 0.37 0.36 0.35 35H 0.39 40H 0.38 0.37 0.36 0.49 0.48 0.47 0.46 0.45 0.44 0.43 0.42 0.41 0.40 0.39 0.38 0.37 0.36 0.35 CCx Copyright © 2010-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 8 XLamp ® MP-L EasyWhite ® LED Standard Order Codes and Bins The following tables list standard kit numbers and performance bins. Kit numbers completely describe an order code’s chromaticity regions and luminous flux range. XLamp MP-L EasyWhite LED Standard Order Codes Minimum Luminous Flux (lm) @ 150 mA* Group Flux (lm) Chromaticity Regions Kit Number EasyWhite B0 C0 D0 E0 700 800 900 1000 27F 0000B027F 27H 0000B027H 30F 0000B030F 30H 0000B030H 35F 0000B035F 35H 0000B035H 27F 0000C027F 27H 0000C027H 30F 0000C030F 30H 0000C030H 35F 0000C035F 35H 0000C035H 40F 0000D040F 40H 0000D040H 40F 0000E040F 40H 0000E040H For other flux and chromaticity combinations, contact Cree or an authorized distributor. * Cree XLamp MP-L EasyWhite LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum specified by the order code without advance notice. Shipments will always adhere to the chromaticity or DWL bin restrictions specified by the order code. Copyright © 2010-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 9 XLamp ® MP-L EasyWhite ® LED Notes Measurements The luminous flux, radiant power, chromaticity and CRI measurements in this document are binning specifications only and solely represent product measurements as of the date of shipment. These measurements will change over time based on a number of factors that are not within Cree’s control and are not intended or provided as operational specifications for the products. Calculated values are provided for informational purposes only and are not intended as specifications. Pre‑Release Qualification Testing Please read the LED Reliability Overview for details of the qualification process Cree applies to ensure long-term reliability for XLamp LEDs and details of Cree’s pre-release qualification testing for XLamp LEDs. Lumen Maintenance Cree now uses standardized IES LM-80-08 and TM-21-11 methods for collecting long-term data and extrapolating LED lumen maintenance. For information on the specific LM-80 data sets available for this LED, refer to the public LM-80 results document. Please read the Long-Term Lumen Maintenance application note for more details on Cree’s lumen maintenance testing and forecasting. Please read the Thermal Management application note for details on how thermal design, ambient temperature, and drive current affect the LED junction temperature. Moisture Sensitivity Cree recommends keeping XLamp MP-L EasyWhite LEDs in the provided, resealable moisture-barrier packaging (MBP) until immediately prior to soldering. Unopened MBPs that contain XLamp LEDs do not need special storage for moisture sensitivity. Once the MBP is opened, XLamp MP-L EasyWhite LEDs should be Temp. Maximum Percent Relative Humidity 30% 40% 50% 60% 70% 80% 90% 35 ºC - - - 17 1 .5 .5 30 ºC - - - 28 1 1 1 25 ºC - - - - 2 1 1 20 ºC - - - - 2 1 1 handled and stored as MSL 2a per JEDEC J-STD-033, meaning they have limited exposure time before damage to the LED may occur during the soldering operation. The table on the right specifies the maximum exposure time in days depending on temperature and humidity conditions. LEDs with exposure time longer than the specified maximums must be baked according to the baking conditions listed below. Baking Conditions It is not necessary to bake all XLamp MP-L EasyWhite LEDs. Only the LEDs that meet all of the following criteria must be baked: 1. LEDs that have been removed from the original MBP. 2. LEDs that have been exposed to a humid environment longer than listed in the Moisture Sensitivity section above. 3. LEDs that have not been soldered. Copyright © 2010-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 10 XLamp ® MP-L EasyWhite ® LED Notes - Continued LEDs should be baked at 80 ºC for 24 hours. LEDs may be baked on the original reels. Remove LEDs from the MBP before baking. Do not bake parts at temperatures higher than 80 ºC. This baking operation resets the exposure time as defined in the Moisture Sensitivity section above. Storage Conditions XLamp MP-L EasyWhite LEDs that have been removed from the original MBP but not soldered should be stored in one of the following ways: • Store the parts in a rigid metal container with a tight-fitting lid. Verify that the storage temperature is <30 °C, and place fresh desiccant and an RH indicator in the container to verify that the RH is no greater than 60%. • Store the parts in a dry, nitrogen-purged cabinet or container that actively maintains the temperature at <30° and the RH at no greater than 60%. • For short-term store only: LEDs can be resealed in the original MBP soon after opening. Fresh desiccant may be needed. Use the included humidity indicator card to verify <60% RH. If an environment of <60% RH is not available for storage, XLamp MP-L EasyWhite LEDs should be baked (described above) before reflow soldering. RoHS Compliance The levels of RoHS restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2011/65/EC (RoHS2), as implemented January 2, 2013. RoHS Declarations for this product can be obtained from your Cree representative or from the Product Documentation sections of www.cree.com. REACh Compliance REACh substances of very high concern (SVHCs) information is available for this product. Since the European Chemical Agency (ECHA) has published notice of their intent to frequently revise the SVHC listing for the foreseeable future, please contact a Cree representative to insure you get the most up-to-date REACh SVHC Declaration. REACh banned substance information (REACh Article 67) is also available upon request. UL® Recognized Component Level 4 enclosure consideration. The LED package or a portion thereof has been investigated as a fire and electrical enclosure per ANSI/ UL 8750. Vision Advisory WARNING. Do not look at an exposed lamp in operation. Eye injury can result. For more information about LEDs and eye safety, please refer to the LED Eye Safety application note. Copyright © 2010-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 11 XLamp ® MP-L EasyWhite ® LED Mechanical Dimensions All measurements are ±.13 mm unless otherwise indicated. 6 5 4 3 2 1 REVISONS NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUTTHE WRITTEN CONSENT OF CREE INC. REV B DESCRIPTION BY DATE ADDED TOLERANCE TO DOME DC 9/9/10 D 6.1 ±0.25 12.15 6.075 11.3 0.7250 13.15 C 12.3 13.15 7.075 BK BA CK CA RK RA 1.275 11 5 11.4 CONTACT PADS SIZE: 0.70 X 0.85 PITCH: 1.25 12.15 SIDE VIEW BOTTOM VIEW TOP VIEW B CATHODE(-): BK, CK, RK ANODE(+): BA, CA, RA A THIRD ANGLE PROJECTION UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX ± .25 .XXX ± .125 X° ± .5 ° FOR SHEET METAL PARTS ONLY .X ± 1.5 .XX ± .75 .XXX ± .25 X° ± .5 ° SURFACE FINISH: 1.6 6 5 4 3 DATE DRAWN BY D. CRONIN CHECK 4600 Silicon D Durham, N.C 2 05/13/09 DATE -- Phone (919) 3 -- APPROVED Fax (919) 313 DATE -- -- MATERIAL -- TITLE MXP LAMP PRODUCT OUTL SIZE FINAL PROTECTIVE FINISH -- SCALE C DRAWING NO. 2601-00004 SHEET 7.000 2 1 Copyright © 2010-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 12 O XLamp ® MP-L EasyWhite ® LED Tape and Reel All Cree carrier tapes conform to EIA-481D, Automated Component Handling Systems Standard. All dimensions in mm. 6 5 4 3 2 1 2400-00009 NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTANED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT OF CREE INC. INDEX QTY ITEM 1 2 1 2 2400-00009-CORE 2400-00009-REEL COMMENTS D D 12.4 +.2 .0 MEASURED AT HUB C 330 +.25 -.75 C 16.4 +0.2 .0 MEASURED AT HUB 1.9±.4 21 ±.4 13.1 ±.2 B B 12.4 +1.0 -.5 MEASURED AT EDGE 60° 60° REVISONS REV A UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX ± .01 .XXX ± .005 X° ± .5 ° ® FOR SHEET METAL PARTS ONLY .X ± .06 .XX ± .03 .XXX ± .010 X° ± .5 ° BY DESCRIPTION DATE APP'D DATE DRAWN BY D. CRONIN 4600 Silicon Drive Durham, N.C 27703 09/29/09 CHECK DATE -- Phone (919) 313-5300 -- APPROVED Fax (919) 313-5558 A DATE -- -- TITLE REEL, 13"and X 12MM, PIECE Copyright © 2010-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree , XLamp and EasyWhite are registered trademarks the Cree3logo is aSNAP trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. ANTI-STATIC HIPS THIRD ANGLE PROJECTION ® SURFACE FINISH: 6 5 4 3 63 ® MATERIAL SIZE FINAL PROTECTIVE FINISH 2 SCALE C 0.500 REV. DRAWING NO. 2400-00009 13 SHEET 1 OF A 1 /1 XLamp ® MP-L EasyWhite ® LED Humidity Indicator Card (inside bag) Packaging Dessicant (inside bag) Unpackaged Reel Label with Cree Bin Code, Quantity, Reel ID Packaged Reel Label with Cree Bin Code, Qty, Lot # Vacuum-Sealed Moisture Barrier Bag Label with Cree Order Code, Quantity, Reel ID, PO # Label with Cree Bin Code, Quantity, Reel ID Label with Custom Code, Qty, Reel ID Boxed Reel Label with Cree Order Code, Quantity, Reel ID, PO # Patent Label Label with Cree Bin Code, Quantity, Reel ID Patent Label Copyright © 2010-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 14