CLD-DS23 Rev 8C Product family data sheet Cree® XLamp® MX-6 LEDs Product Description FEATURES Table of Contents The Cree XLamp® MX-6 LED provides the • Available in white (2200 K and Characteristics.......................................... 2 proven lighting‑class performance and 2600 K to 8300 K CCT) Flux Characteristics.................................. 3 reliability of Cree XLamp LEDs in a flat‑top • Maximum drive current: 1000 mA Relative Spectral Power Distribution....... 4 PLCC package. The XLamp MX‑6 LED • Wide viewing angle: 120° Relative Flux vs. Junction Temperature... 4 continues Cree’s history of innovation in • Electrically neutral thermal path Electrical Characteristics.......................... 5 LEDs for lighting applications with wide • Qualification at max drive current Relative Flux vs. Current........................... 5 viewing angle, unlimited floor life, uniform • RoHS- and REACh-compliant Typical Spatial Distribution....................... 6 light output without secondary optics and • UL® recognized component Thermal Design......................................... 6 electrically neutral thermal path. (E349212) Reflow Soldering Characteristics............. 7 Notes......................................................... 8 The XLamp MX-6 LED brings high Mechanical Dimensions......................... 10 performance and quality of light to a wide Tape and Reel.......................................... 11 range of lighting applications, including Packaging................................................ 12 linear lighting, LED light bulbs, fluorescent www.cree.com/Xlamp retrofits and retail-display lighting. Copyright © 2009-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 1 XLamp ® MX-6 LED Characteristics Characteristics Unit Thermal resistance, junction to solder point °C/W 5 degrees 120 mV/°C -3.3 Viewing angle (FWHM) Temperature coefficient of voltage ESD classification (HBM per Mil-Std-883D) DC forward current Minimum Typical Maximum Class 2 mA Forward voltage (@ 300 mA) V LED junction temperature °C 1000 3.3 3.8 150 Copyright © 2009-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 2 XLamp ® MX-6 LED Flux Characteristics (TJ = 25 °C) The following table provides several base order codes for XLamp MX-6 LEDs. It is important to note that the base order codes listed here are a subset of the total available order codes for the product family. For more order codes, as well as a complete description of the order‑code nomenclature, please consult the XLamp MX LED Family Binning & Labeling document. Color CCT Range Minimum Cool White Maximum 5000 K 8300 K 5000 K 8300 K 80-CRI White Warm White 3700 K 4300 K 2600 K 3700 K 3700 K 4300 K 2600 K 3700 K 2200 K Minimum Luminous Flux (lm) @ 300 mA Calculated Minimum Luminous Flux (lm) @ 350 mA* Order Code Group Flux (lm) Flux (lm) Rs 114 130 MX6AWT-A1-0000-000E51 Q5 107 122 MX6AWT-A1-0000-000D51 Q5 107 122 MX6AWT-A1-0000-000DE3 Q4 100 114 MX6AWT-A1-0000-000CE3 Q5 107 122 MX6AWT-H1-0000-000D51 Q4 100 114 MX6AWT-H1-0000-000C51 Q5 107 122 MX6AWT-H1-0000-000DE3 Q4 107 114 MX6AWT-H1-0000-000CE3 Q4 100 114 MX6AWT-H1-0000-000CE5 Q3 93.9 107 MX6AWT-H1-0000-000BE5 Q3 93.9 107 MX6AWT-H1-0000-000BE7 Q2 87.4 100 MX6AWT-H1-0000-000AE7 Q4 100 114 MX6AWT-A1-0000-000CE5 Q3 93.9 107 MX6AWT-A1-0000-000BE5 Q3 93.9 107 MX6AWT-A1-0000-000BE7 Q2 87.4 100 MX6AWT-A1-0000-000AE7 P4 80.6 92 MX6AWT-A1-0000-0009EA P3 73.9 84 MX6AWT-A1-0000-0008EA P2 67.2 77 MX6AWT-A1-0000-0007EA Notes: • Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements. See the Measurements section (page 8). • Typical CRI for Cool White (4300 K – 8300 K CCT) is 75. • Typical CRI for Warm White (2200 K and 2600 K – 4300 K CCT) is 80. • Minimum CRI for 80-CRI White is 80. * Calculated values for reference purposes only. Copyright © 2009-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 3 XLamp ® MX-6 LED Relative Spectral Power Relative Spectral Power Distribution Relative Radiant Power (%) 100 80 5000K - 8300K CCT 3500K - 5000K CCT 2600K - 3500K CCT 2200K CCT 60 40 20 0 380 430 480 530 580 630 680 730 780 Wavelength (nm) Relative Flux Output vs. Junction Temperature Relative Flux vs. Junction Temperature (IF = 300 mA) 100% 90% Relative Luminous Flux 80% 70% 60% 50% 40% 30% 20% 10% 0% 25 50 75 100 125 150 Junction Temperature (ºC) Copyright © 2009-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 4 XLamp ® MX-6 LED Electrical Characteristics (TJ = 25 °C) 1000 900 Forward Current (mA) 800 700 600 500 400 300 200 100 0 2.50 2.75 3.00 3.25 3.50 3.75 4.00 4.25 4.50 Forward Voltage (V) Relative Flux vs. Current (TJ = 25 °C) Relative Luminous Flux (%) 300 250 200 150 100 50 0 100 200 300 400 500 600 700 800 900 1000 Forward Current (mA) Copyright © 2009-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 5 XLamp ® MX-6 LED Typical Spatial Distribution Relative Luminous Intensity (%) 100 80 60 40 20 0 -100 -80 -60 -40 -20 0 20 40 60 80 100 Angle (º) Thermal Design The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is crucial for the end - roboto product to be Thermal designedDesign in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life and optical characteristics. 1200 Maximum Current (mA) 1000 800 600 Rj-a = 10°C/W Rj-a = 15°C/W 400 Rj-a = 20°C/W Rj-a = 25°C/W 200 0 0 20 40 60 80 100 120 140 160 Ambient Temperature (ºC) Copyright © 2009-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 6 XLamp ® MX-6 LED Reflow Soldering Characteristics In testing, Cree has found XLamp MX-6 LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of the solder paste used. Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment. tP TP Critical Zone TL to TP Temperature Ramp-up TL tS Tsmax Tsmin Ramp-down ts Preheat 25 t 25˚C to Peak Profile Feature Average Ramp-Up Rate (Tsmax to Tp) Time Lead-Free Solder 1.2 °C/second Preheat: Temperature Min (Tsmin) 120 °C Preheat: Temperature Max (Tsmax) 170 °C Preheat: Time (tsmin to tsmax) 65-150 seconds Time Maintained Above: Temperature (TL) Time Maintained Above: Time (tL) 217 °C 45-90 seconds Peak/Classification Temperature (Tp) 235 - 245 °C Time Within 5 °C of Actual Peak Temperature (tp) 20-40 seconds Ramp-Down Rate 1 - 6 °C/second Time 25 °C to Peak Temperature 4 minutes max. Note: All temperatures refer to the topside of the package, measured on the package body surface. Copyright © 2009-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 7 XLamp ® MX-6 LED Notes Measurements The luminous flux, radiant power, chromaticity and CRI measurements in this document are binning specifications only and solely represent product measurements as of the date of shipment. These measurements will change over time based on a number of factors that are not within Cree’s control and are not intended or provided as operational specifications for the products. Calculated values are provided for informational purposes only and are not intended as specifications. Pre‑Release Qualification Testing Please read the LED Reliability Overview for details of the qualification process Cree applies to ensure long-term reliability for XLamp LEDs and details of Cree’s pre-release qualification testing for XLamp LEDs. Lumen Maintenance Cree now uses standardized IES LM-80-08 and TM-21-11 methods for collecting long-term data and extrapolating LED lumen maintenance. For information on the specific LM-80 data sets available for this LED, refer to the public LM-80 results document. Please read the Long-Term Lumen Maintenance application note for more details on Cree’s lumen maintenance testing and forecasting. Please read the Thermal Management application note for details on how thermal design, ambient temperature and drive current affect the LED junction temperature. Moisture Sensitivity Cree recommends keeping XLamp MX-6 LEDs in the provided, resealable moisture-barrier packaging (MBP) until immediately prior to soldering. Unopened MBPs that contain XLamp LEDs do not need special storage for moisture sensitivity. Once the MBP is opened, XLamp MX-6 LEDs should be handled and stored as MSL 2a per JEDEC J-STD-033, meaning they have limited exposure time before damage to the LED may occur during the soldering operation. The table on the right specifies the maximum exposure time Temp. Maximum Percent Relative Humidity 30% 40% 50% 60% 70% 80% 90% in days depending on temperature and humidity conditions. LEDs with 35 ºC - - - 17 1 .5 .5 exposure time longer than the specified maximums must be baked 30 ºC - - - 28 1 1 1 according to the baking conditions listed below. 25 ºC - - - - 2 1 1 20 ºC - - - - 2 1 1 Baking Conditions It is not necessary to bake all XLamp MX-6 LEDs. Only the LEDs that meet all of the following criteria must be baked: 1. LEDs that have been removed from the original MBP. 2. LEDs that have been exposed to a humid environment longer than listed in the Moisture Sensitivity section above. 3. LEDs that have not been soldered. LEDs should be baked at 70 ºC for 24 hours. LEDs may be baked on the original reels. Remove LEDs from the MBP before baking. Do not bake parts at temperatures higher than 70 ºC. This baking operation resets the exposure time as defined in the Moisture Sensitivity section above. Copyright © 2009-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 8 XLamp ® MX-6 LED Notes - Continued Storage Conditions XLamp MX-6 LEDs that have been removed from the original MBP but not soldered should be stored in one of the following ways: • Store the parts in a rigid metal container with a tight-fitting lid. Verify that the storage temperature is <30 °C, and place fresh desiccant and an RH indicator in the container to verify that the RH is no greater than 60%. • Store the parts in a dry, nitrogen‑purged cabinet or container that actively maintains the temperature at <30° and the RH at no greater than 60%. • For short-term store only: LEDs can be resealed in the original MBP soon after opening. Fresh desiccant may be needed. Use the included humidity indicator card to verify <60% RH. If an environment of <60% RH is not available for storage, XLamp MX-6 LEDs should be baked (described above) before reflow soldering. RoHS Compliance The levels of RoHS restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2011/65/EC (RoHS2), as implemented January 2, 2013. RoHS Declarations for this product can be obtained from your Cree representative or from the Product Documentation sections of of www.cree.com. REACh Compliance REACh substances of very high concern (SVHCs) information is available for this product. Since the European Chemical Agency (ECHA) has published notice of their intent to frequently revise the SVHC listing for the foreseeable future, please contact a Cree representative to insure you get the most up-to-date REACh SVHC Declaration. REACh banned substance information (REACh Article 67) is also available upon request. UL® Recognized Component Level 4 enclosure consideration. The LED package or a portion thereof has been investigated as a fire and electrical enclosure per ANSI/ UL 8750. Vision Advisory WARNING: Do not look at an exposed lamp in operation. Eye injury can result. For more information about LEDs and eye safety, please refer to the LED Eye Safety application note. Copyright © 2009-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 9 XLamp ® MX-6 LED Mechanical Dimensions All measurements are ±.13 mm unless otherwise indicated. Top View Top View Bottom View Side View Recommended FR4 Solder Pad Recommended MCPCB Solder Pad Alternative Solder Pad Copyright © 2009-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 10 6 5 4 3 2 1 REVISONS NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUTTHE WRITTEN CONSENT OF CREE INC. REV DESCRIPTION BY A Released J.L. 7/1/09 B ADDED CATHODE AND ANODE NOTES DC 2/26/12 8.0±.1 1.75±.10 APP'D XLamp ® MX-6 LED 1.5±.1 4.0±.1 DATE 2.5±.1 D Cathode Side Tape and Reel All Cree carrier tapes +.3 conform to EIA-481D, Automated Component Handling Systems Standard. 12.0 .0 Except as noted, all dimensions in mm. ( Cathode Mark Anode Side (denoted by + and circle) (4 ) (8 ) 1.5 ) C CATHODE SIDE Direction User Feed (1.75 ) END (1.55 ) START (12 ) Trailer 160mm (min) of Trailer empty pockets 160mm (min) of pockets sealedempty with tape sealed with tape (20 pockets (20 pocketsmin.) min.) Loaded Pockets (1,000 Lamps) Loaded Pockets (1,400 pcs /Reel ANODE SIDE Leader 400mm (min) of Leader empty pockets with 400mm (min) of empty pockets with at least 100mm at least 100mm sealed by tape sealed by tape (50 empty pockets min.) (50 empty pockets min.) B User Feed Direction Cover Tape THIRD ANGLE PROJECTION UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX ± .25 .XXX ± .125 X° ± .5 ° FOR SHEET METAL PARTS ONLY .X ± 1.5 .XX ± .75 .XXX ± .25 X° ± .5 ° DATE DRAWN BY D. Seibel DATE APPROVED DATE 5 4 3 Phone (919) 313-5300 Fax (919) 313-5558 A TITLE Carrier Loading Specification-MX6 MATERIAL SIZE FINAL PROTECTIVE FINISH SCALE SURFACE FINISH: 1.6 6 4600 Silicon Drive Durham, N.C 27703 7/1/09 CHECK Pocket Tape 2 C 4.000 REV. DRAWING NO. 2402-00005 SHEET 1 13mm 7" Copyright © 2009-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 11 B OF 1 /2 XLamp ® MX-6 LED Packaging Unpackaged Reel Vacuum-Sealed Vacuum-Sealed Moisture Barrier Bag Moisture Barrier Bag Label CREE Binwith Code Cree Bin & Barcode LabelLot # Code, Qty, Label with Cree Bin Code, Quantity, Reel ID Label with Cree Bin Label with Customer P/N, Qty,Qty, Lot #, Lot PO # # Code, Packaged Reel Patent Label Dessicant (inside bag) Label with Customer Order Label with Cree Order Code, Code, Qty, Reel ID, PO # Quantity, Reel ID, PO # Humidity Indicator Card (inside bag) Label with Cree Bin Code, Quantity, Reel ID Boxed Reel Label with Cree Order Code, Quantity, Reel ID, PO # Label with Cree Bin Code, Quantity, Reel ID Patent Label (on bottom of box) Copyright © 2009-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. 12