General Information www.vishay.com Vishay Roederstein Ceramic Disc, RFI, and Safety Capacitors In accordance with IEC recommendations ceramic capacitors are subdivided into two classes: • CERAMIC CLASS 1 or low-K capacitors are mainly manufactured of titanium dioxide or magnesium silicate • CERAMIC CLASS 2 or high-K capacitors contain mostly alkaline titanate MAIN FEATURES CLASS 1 CLASS 2 Application For temperature compensation of frequency discriminating circuits and filters, coupling and decoupling in high-frequency circuits where low losses and narrow capacitance tolerances are demanded. As RFI and safety capacitors. As coupling and decoupling capacitors for such application where higher losses and a reduced capacitance stability are required. As RFI and safety capacitors. Properties Temperature Dependence Capacitance High stability of capacitance. Low dissipation factor up to higher frequencies. Defined temperature coefficient of capacitance, positive or negative, linear, and reversible. High insulation resistance. No voltage dependence. High long-term stability of electrical values. High capacitance values with small dimensions. Non-linear dependence of capacitance on temperature. DC Voltage Capacitance Dependence None Increasing with Dissipation Factor tan Maximum 1.5 x 10-3 (typical) Maximum 35 x 10-3 (typical) Insulation Resistance 1010 Capacitance Tolerances ± 5 %, ± 10 %, ± 20 % ± 10 %, ± 20 %, + 50 % / - 20 %, + 80 % / - 20 % Rated Voltage Up to 25 kVDC Up to 15 kVDC 109 STANDARD SPECIFICATIONS GENERAL STANDARDS IEC 60062 Marking codes for resistors and capacitors IEC 60068 Basic environmental testing procedures SPECIAL STANDARDS FOR CERAMIC CAPACITORS EN 130600 and IEC 60384-8 Fixed capacitors of ceramic dielectric, class 1 EN 130700 and IEC 60384-9 Fixed capacitors of ceramic dielectric, class 2 STANDARDS FOR SPECIAL APPLICATION PURPOSES IEC 60384-14 DIN EN 60384-14 RFI and safety capacitors UL 60384-14 CSA E60384-14 MEASURING AND TESTING CONDITIONS CLASS 1 CLASS 2 Capacitance and Dissipation Factor C 1000 pF 1 kHz, 1.0 VRMS to 5 VRMS C < 1000 pF 1 MHz, 1.0 VRMS to 5 VRMS C 100 pF 1 kHz, 1.0 VRMS ± 0.2 VRMS C < 100 pF 1 MHz, 1.0 VRMS ± 0.2 VRMS Insulation Resistance Rated voltage Measuring time: < 100 V: 100 V to < 500 V: 500 V: measuring voltage = 10 V ± 1 V measuring voltage = 100 V ± 15 V measuring voltage = 500 V ± 50 V 60 s ± 5 s Dielectric Strength Rated voltage: Testing time: 500 V: > 500 V: test voltage = 2.5 x UR test voltage = 1.5 x UR 2s Note • Climatic test conditions: Temperature Relative humidity Revision: 21-Aug-15 20 °C to 25 °C 50 % to 70 % Document Number: 22001 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay Roederstein MARKING See individual datasheet. CAPACITANCE CODING SYSTEM CAPACITANCE VALUE CODE p33 3p3 33p 330p n33 3n3 33n 330n μ33 3μ3 CAPACITANCE TOLERANCE CAPACITANCE VALUE 0.33 pF 3.3 pF 33 pF 330 pF 330 pF (0.33 nF) 3300 pF (3.3 nF) 33 000 pF (33 nF) 330 000 pF (330 nF) 0.33 μF 3.3 μF C-TOLERANCE C-TOLERANCE < 10 pF (pF) 10 pF (%) ± 0.1 ± 0.25 ± 0.5 ± 0.5 ±1 ±1 ±2 ±2 ± 2.5 ±5 ± 10 ± 15 ± 20 (+ 30 / - 20) (+ 50 / - 20) (+ 80 / - 20) Clear text CODE LETTER B C D F G H J K L M R S Z RATED VOLTAGE PRODUCTION CODE ACCORDING TO IEC 60062 The production code is indicated either with a 2 FIGURE CODE or with a 4 FIGURE CODE. 2 FIGURE CODE (YEAR / MONTH) The 1st figure indicates the year and the 2nd figure indicates the month. YEAR 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020 LETTER CODE M N MONTH LETTER / NUMBER CODE P R S T U V W X A B C D E F H J K L M January February March April May June July August September October November December 1 2 3 4 5 6 7 8 9 O N D 4 FIGURE CODE (YEAR / WEEK) The 1st two figures indicate the year and the second two figures indicate the week. EXAMPLES EXAMPLES 2000 August = M8 32nd week 2000 = 0032 2001 May = N5 41st week 2001 = 0141 2002 October = PO 27th week 2002 = 0227 2014 March = E3 19th week 2014 = 1419 2017 December = JD 12th week 2016 = 1612 2019 May = L5 35th week 2020 = 2035 Revision: 21-Aug-15 Document Number: 22001 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay Roederstein CODING OF THE TEMPERATURE CHARACTERISTIC OF CAPACITANCE FOR CLASS 2 CERAMIC CAPACITORS ACCORDING TO EN 130700 OR IEC 60384-9 2 Marking for class 2 ceramic capacitor D 3 Admissible capacitance change related to 20 °C over the entire temperature range DC VOLTAGE Temperature range: upper and lower temperature limits WITHOUT WITH CODE LETTER TEMPERATURE RANGE CODE FIGURE ± 10 % + 10 % / - 15 % B -55 °C to +125 °C 1 ± 20 % + 20 % / - 30 % C -55 °C to +85 °C 2 + 20 % / - 30 % + 20 % / - 40 % D -40 °C to +85 °C 3 + 22 % / - 56 % + 22 % / - 70 % E -25 °C to +85 °C 4 F -10 °C to +85 °C 5 + 30 % / - 80 % + 30 % / - 90 % ± 15 % + 15 % / - 40 % R ± 15 % + 15 % / - 25 % X ACCORDING TO EIA STANDARD RS 198 Y Lower category temperature TEMPERATURE 5 S Upper category temperature Admissible capacitance change related to 25 °C over the entire temperature range CODE LETTER TEMPERATURE CODE FIGURE -55 °C X +45 °C 2 ±1% A -30 °C Y +65 °C 4 ± 1.5 % B +10 °C Z +85 °C 5 ± 2.2 % C +105 °C 6 ± 3.3 % D +125 °C 7 ± 4.7 % E Revision: 21-Aug-15 CHANGE CODE LETTER ± 7.5 % F ± 10 % P ± 15 % R ± 22 % S ± 22 %/- 33 % T ± 22 %/- 56 % U ± 22 %/- 82 % V Document Number: 22001 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay Roederstein CLASS 1 CERAMIC TYPE TEMPERATURE COEFFICIENT OF THE CAPACITANCE FOR CLASS 1 CERAMIC CAPACITORS C = capacitance change = temperature coefficient in 10 - 6/°C = temperature change in °C C -------- % = 100 x x C 40 ΔC [%] C 50 30 N 2200 (K) N 750 (U) 20 10 0 -10 N 750 (U) -20 N 2200 (K) -30 -40 -50 -55 -40 -20 0 20 40 60 80 100 120 85 ϑ u [°C] VOLTAGE DEPENDENCE OF CAPACITANCE None FREQUENCY DEPENDENCE OF CAPACITANCE Maximum -2 at 1 MHz DISSIPATION FACTOR • For values greater than 50 pF: see datasheet • For lower values the dissipation factor is calculated according to the type of ceramic (rated temperature coefficient) under consideration of the capacitance according to EN 130600 +100 -750: +750 -1500: +1500 -3300: +3300 -5600: -5600: 150 1.5 x ---------- + 7 x 10 -4 C 150 2 x ---------- + 7 x 10 -4 C 150 3 x ---------- + 7 x 10 -4 C 150 4 x ---------- + 7 x 10 -4 C 150 5 x ---------- + 7 x 10 -4 C • The dissipation factor as well as the measuring method to be agreed between manufacturer and user for values lower than 5 pF. Revision: 21-Aug-15 Document Number: 22001 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay Roederstein CLASS 2 CERAMIC TYPE CAPACITANCE CHANGE VS. DC VOLTAGE CAPACITANCE CHANGE AND DISSIPATION FACTOR VS. FREQUENCY CAPACITANCE CHANGE AND DISSIPATION FACTOR VS. TEMPERATURE Capacitance 10 60 30 20 Capacitance 10 4700 p 0 0 40 -10 -10 ΔC/C [%] 20 tan δ x 10-3 60 ΔC/C [%] 30 20 tan δ x 10-3 ΔC/C [%] CERAMIC DIELECTRIC: 2D3 / Y5T +20 0 40 100 p -20 -20 -20 30 -30 -30 -40 20 20 tan -55 -55 -60 tan -80 -40 0 +20 +55 -80 0 -80 +85 102 103 105 104 107 106 ϑ u [°C] 0 20 40 60 80 f [Hz] 100 UN [%] 10 Capacitance 10 10 nF 0 0 40 -10 20 0 -20 1 nF -20 -30 +20 40 -10 -20 ΔC/C [%] Capacitance 60 30 tan δ x 10-3 60 ΔC/C [%] 30 20 tan δ x 10-3 ΔC/C [%] CERAMIC DIELECTRIC: 2E3 / Y5U -30 -40 20 20 ta n -55 -80 -40 -55 0 +20 0 -80 +85 +55 -60 ta n 102 103 105 104 106 ϑ u [°C] -80 107 0 20 40 60 80 f [Hz] 100 UN [%] 10 60 30 20 Capacitance 10 10 nF 0 0 40 -10 ΔC/C [%] Capacitance tan δ x 10-3 20 ΔC/C [%] 60 30 tan δ x 10-3 ΔC/C [%] CERAMIC DIELECTRIC: 2F3 / Y5V +20 0 40 -10 1 nF -20 -20 -20 -30 -30 -40 tan 20 20 ta n -55 -60 -55 -80 -40 0 +20 +55 +85 ϑ u [°C] Revision: 21-Aug-15 0 -80 102 103 104 105 106 107 f [Hz] -80 0 20 40 60 80 100 UN [%] Document Number: 22001 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay Roederstein CAPACITANCE “AGING” OF CERAMIC CAPACITORS Following the final heat treatment all class 2 ceramic capacitors reduce their capacitance value approximately according to logarithmic law due to their special crystalline construction. This change is called “aging”. If the capacitors are heat treated, for example when soldering, the capacitance increases again to a higher value and the aging process begins again. Note • The level of this de-aging is dependent on the temperature and the duration of the heat; an almost complete de-aging is achieved at 150 °C in one hour; these conditions also form the basis for reference measurements when testing. The capacitance change per time decade (aging constant) differs for the various types of ceramic but typical values can be taken from the table below. CERAMIC MATERIAL Y5T Y5U Y5V AGING CONSTANT k -4 % -4 % -5 % 100 x C t1 - C t2 k = -----------------------------------------------C t1 x log 10 t1/t2 t1, t2 = measuring time point (h) Ct1, Ct2 = capacitance values for the times t1, t2 k = aging constant (%) C t2 = C t1 x 1 - k/100 x log 10 t1 t2 REFERENCE MEASUREMENT Due to aging it is necessary to specify an age for reference measurements which can be related to the capacitance with fixed tolerance. According to EN 130700 this time period is 1000 h. If the shelf-life of the capacitor is known, the capacitance for t = 1000 h can be calculated with the aging constant. In order to avoid the influence of the aging, it is important to de-age the capacitors before stress-testing. The following procedure is adopted (see also EN 130700): • De-aging at 150 °C, 1 h • Storage for 24 h at standard climatic conditions • Initial measurement • Stress • De-aging at 150 °C, 1 h • Storage for 24 h at standard climatic conditions • Final measurement Revision: 21-Aug-15 Document Number: 22001 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay Roederstein COMPONENT CLIMATIC CATEGORY 40 / 085 / 21 1st SET 2nd SET 3rd SET Minimum ambient temperature of operation (test cold) Maximum ambient temperature of operation (dry heat test) Number of days (steady steat test) First set: two digits denoting the minimum ambient temperature of operation (cold test). Second set: three digits denoting the maximum ambient temperature (dry heat test). Third set: two digits denoting the number of days of the damp heat steady state test (Ca). Standard coding according to IEC 60068-1. 65 -65 °C 55 -55 °C 40 -40 °C 25 -25 °C 10 -10 °C 00 0 °C 05 +5 °C 155 +155 °C 125 +125 °C 110 +110 °C 090 +90 °C 085 +85 °C 080 +80 °C 075 +75 °C 070 +70 °C 065 +65 °C 060 +60 °C 055 +55 °C 56 56 days 21 21 days 10 10 days 04 4 days 00 The component is not required to be exposed to damp heat CATEGORY EXAMPLES 25/085/04 25/085/21 40/085/21 55/125/21 55/125/56 Revision: 21-Aug-15 Document Number: 22001 7 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay Roederstein STORAGE The capacitors must not be stored in a corrosive atmosphere, where sulphide or chloride gas, acid, alkali or salt are present. Exposure of the components to moisture, should be avoided. The solderability of the leads is not affected by storage of up to 24 months (temperature +10 °C to +35 °C, relative humidity up to 60 %). Class 2 ceramic dielectric capacitors are also subject to aging, see previous page. SOLDERING SOLDERING SPECIFICATIONS Soldering test for capacitors with wire leads: (according to IEC 60068-2-20, solder bath method) Soldering temperature Soldering duration Distance from component body SOLDERABILITY RESISTANCE TO SOLDERING HEAT 235 °C ± 5 °C 260 °C ± 5 °C 2 s ± 0.5 s 10 s ± 1 s 2 mm 5 mm SOLDERING RECOMMENDATIONS Soldering of the component should be achieved using a Sn60/40 type or a silver-bearing Sn62/36/2Ag type solder. Ceramic capacitors are very sensitive to rapid changes in temperature (thermal shock) therefore the solder heat resistance specification (see Soldering Specifications table) should not be exceeded. Subjecting the capacitor to excessive heating may result in thermal shocks that can crack the ceramic body. Similarly, excessive heating can cause the internal solder junction to melt. CLEANING The components should be cleaned immediately following the soldering operation with vapor degreasers. SOLVENT RESISTANCE The coating and marking of the capacitors are resistant to the following test method: IEC 60068-2-45 (method XA). MOUNTING We do not recommend modifying the lead terminals, e.g. bending or cropping. This action could break the coating or crack the ceramic insert. If however, the lead must be modified in any way, we recommend support of the lead with a clamping fixture next to the coating. Revision: 21-Aug-15 Document Number: 22001 8 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay Roederstein AQL / FIT VALUES / SUPPLIED QUALITY AQL 0.1 FOR THE SUM OF THE ELECTRIC MAIN FAULTS • C-tolerance > 1.5 x tolerance limit • DF > 1.5 x catalog value • RIS < catalog value • Inadequate dielectric breakdown • Interruption AQL 0.25 FOR THE SUM OF THE MECHANICAL MAIN FAULTS • Marking wrong or missing • Dimensions out of tolerance • Coating failure • Lead space out of tolerance • Poor solderability of leads • Wrong lead length AQL 0.65 FOR SECONDARY FAULTS • Coating extension out of tolerance • Marking incomplete • Tape dimensions out of tolerance • Testing in accordance to IEC 60410 Notes The following agreements are possible on request: • Lower AQL values • Confirmed initial random sampling test with appropriate report • Report on production test findings • Agreement on ppm concept RELIABILITY By careful control of the manufacturing process stages, the quality of the product is maintained at the highest possible level. To obtain data on the reliability of our ceramic capacitors, many long-term tests under increased temperature and voltage conditions have been carried out in our laboratories. Based on the results of these tests, the following can be stated: Reference conditions: Ambient temperature: Relative humidity: Electrical stress: Failure criteria: Short circuit (R 10-5 ) or open circuit Failure tests: Class 1 capacitors: Class 2 capacitors: 40 °C ± 2 °C 60 % ± 2 % 50 % rated voltage (UR) = 2 x 10-9 h-1 = 5 x 10-9 h-1 By derating the voltage load, greatly increased reliability can be predicted. Temperature, up to the maximum category temperature, is not believed to significantly affect the reliability. Revision: 21-Aug-15 Document Number: 22001 9 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay Roederstein PRODUCTION FLOWCHART Raw Material Batching PC 1 Wet Prepared in ball-mill Spray Drying Process PC 2 QC 1 Pressing Discs PC 3 Sinter Process (firing) PC 4 QC 2 Screen Printing of Both Electrodes Firing of Electrodes PC 5 Sorting in Tolerance Classes if necessary PC 6 QC 3 Forming and Soldering Leads PC 7 Aligning for Coating Process Epoxy or Phenol Resin Coating PC 8 Hardening Resin Coat Marking 100 % Test C - Value Dissipation Factor Voltage Test PC 9 Visual Inspection QC 4 Cutting leads for bulk packaging or taping PC 10, 11 Packaging QC 5 Delivery Revision: 21-Aug-15 PC = Production Control QC = Quality Control Document Number: 22001 10 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay Roederstein AVAILABLE STANDARD LEAD CONFIGURATIONS FORM 4 7.5 to 5.0 CRIMP V FORM 1 STRAIGHT LEAD e 3.0 MAX. L 30 - 3 or 10 ± 1 F S max. d 0.6 or 0.8 F 5.0*) / 7.5 / 10 / 12.5 0.6 L 3.0 MIN. e max. D max. d *) only when d = 0.6 F Coating on lead shall not extend below this line D B ≤9 6.8 ± 0.7 >9 7.5 ± 0.7 Point of support on printed cardboard V Ø d ± 0.05 FORM 2 INSIDE CRIMP FORM 5 SNAP-IN 0.8 V 0.6 V d d 0.6 or 0.8 L 3.0 MIN., 1.0 absolute 7.5 4.0 ± 1.5 10 5.0 ± 1.5 12.5 6.0 ± 1.5 A ± 1.5 4.0 - 1 + 0.5 2.8 MIN. F 3.5 MIN. H 2.6 3.3 P1 1.25 1.65 P2 1.65 1.95 *) only when d = 0.6 L 5.0*) L 1.8+- 0.5 0.2 *) 1.8+- 0.5 0.2 *) *) only when d = 0.6 WYO series: Kink = 1.4 + 0.5 - 0.2 F Ø d ± 0.05 FORM 3 OUTSIDE CRIMP V D B ≤8 6.0 ± 1.5 >8 7.0 ± 1.5 P1 S max. D max. Coating on lead shall not extend below this line Point of support on printed cardboard H +- 0.3 0.3 Point of support on printed cardboard Coating on lead shall not extend below this line A 5.0* / 7.5 / 10 / 12.5 A ± 1.5 L +- 1.5 0 S max. D max. F F F V + 0.3 - 0.1 P2 + 0.3 - 0.1 Ø d ± 0.05 F FORM 6 INLINE WIRE 5.0*) 0.6 5.0 7.5 0.6 5.0 7.5 0.6 6.0 10 0.6 6.0 10 0.6 6.0 12.5 0.6 6.0 12.5 0.6 6.0 F Coating on lead shall not extend below this line F d A 7.5 0.6 4.5 MAX. 10 0.8 6.0 MAX. 12.5 0.8 6.0 MAX. F 7.5 *) only when d = 0.6 Revision: 21-Aug-15 S max. D max. Point of support on printed cardboard Point of support on printed cardboard Coating on lead shall not extend below this line A A H d 10 12.5 L 2.8 MIN. 1.5 absolute 3.0 MIN. 2.0 absolute 3.0 MIN. 2.0 absolute L F F Ø d ± 0.05 Document Number: 22001 11 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay Roederstein RADIAL TAPING OF CERAMIC DISC CAPACITORS DESIGNATION SYMBOL TAPING P TAPING T TAPING U TAPING F Pitch of component P 12.7 ± 1 25.4 ± 1 Pitch of sprocket hole P0 12.7 ± 0.3 12.7 ± 0.3 Distance, hole to lead P1 3.85 ± 0.7 (0.5F) ± 0.7 Distance, hole to center of component P2 6.35 ± 1.3 12.7 ± 1.3 Lead spacing F 5.0 / 7.5 + 0.8 / - 0.2 5 / 7.5 / 10 / 12.5 ± 0.8 Average deviation across tape h ± 2.0 max. ± 3.0 max. Average deviation in direction of reeling p ± 1.3 max. ± 1.3 max. Carrier tape width W 18.0 + 1 / - 0.5 18.0 + 1 / - 0.5 Hold-down tape width W0 6 6 Position of sprocket hole W1 9.0 + 0.75 / - 0.5 9.0 + 0.75 / - 0.5 Distance of hold-down tape W2 3.0 max. 3.0 max. Distance between the abscissa and the bottom plane of the component body (straight leads) H Distance between the abscissa and the reference plane of the component with crimped leads (kinked leads) H0 16.0 ± 0.5 16.0 ± 0.5 Length of cut leads L 11.0 max. 11.0 max. Diameter of sprocket hole D0 4.0 ± 0.2 4.0 ± 0.2 t 0.9 max. 0.9 max. Total tape thickness 16.5 ± 0.5 18.0 + 2 / - 0 16.5 ± 0.5 18.0 + 2 / - 0 20.0 ± 1 20 ± 1 PACKAGING VERSIONS Reel Packaging Ammo Packaging io ect 340 max. Ø 16 + 1 Dir g elin nre fu no 60 max. 340 350 max. x. ma 55 max. Revision: 21-Aug-15 Document Number: 22001 12 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay Roederstein TAPING P / T / U COMPONENT PITCH 0.5" LEAD SPACING 5.0 mm P2 P Δh Reference Line Δp Δp S L W0 H0 W H H1 W1 W2 D Δh P0 D0 d F t P1 P Δp S W0 H0 H1 H L Δh W W1 D Δh W2 Δp Reference Line TAPING P / T / U COMPONENT PITCH 0.5" LEAD SPACING 7.5 mm D0 P0 P1 d t F Reference Line TAPING F COMPONENT PITCH 1.0" LEAD SPACING 5.0 mm, 7.5 mm, 10 mm, 12.5 mm P Δp P2 Δp S W0 P1 H0 H1 W2 H L W1 W2 D0 Δh F P0 d t • Pulling force from the tape ≥ 5 N • Tensile strength of tape ≥ 15 N • Unreeling force of tape from reel ≥ 2.5 N W0 W W1 D Δh Maximum 0.5 % of all components on reel may be missing. A maximum of 3 consecutive components may be missing provided this gap is followed by 6 consecutive components. The splices shall have the same minimum strength as the tape. The splices must be not thicker than 1.5 mm, the sprocket holes may not be effected. Revision: 21-Aug-15 Document Number: 22001 13 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay Roederstein The ordering code is made up of a 14-digit code. ORDERING INFORMATION EXAMPLE H... / I... / V... / W... SERIES WYO 472 M CM CF0 K R 123 456 7 89 10 11 12 13 14 CAPACITOR SERIES CAPACITANCE VALUE IN pF TOLERANCE RATED VOLTAGE LEAD CONFIGURATION INTERNAL CODE RoHS To be taken from the respective individual datasheet 1st two digits J=±5% represent K = ± 10 % AQ = 500 VDC BA = 1 kVDC BB = 2 kVDC BC = 3 kVDC BD = 4 kVDC BE = 5 kVDC BF = 6 kVDC BP = 8 kVDC BH = 10 kVDC BJ = 15 kVDC BQ = 25 kVDC STRAIGH LEADS OR INSIDE CRIMP significant M = ± 20 % figures S = + 50 % / - 20 % 3rd digit is the Z = + 80 % / - 20 % multiplier (x 10) e.g. 1.6 pF = 916 10 pF = 100 120 pF = 121 4700 pF = 472 W1X Series: CV = 275 VAC 22 nF = 223 WYO Series: CM = 250 VAC, 440 VAC VKO Series: CQ = 300 VAC, 440 VAC WKO Series: CP = 300 VAC, 440 VAC 10th digit Lead spacing B = 5.0 mm C = 7.5 mm D = 10 mm E = 12.5 mm RoHS compliant indicator 11th digit (1) Lead length / dia. B = 6 + 0 - 1 / 0.6 D = 10 ± 1 / 0.6 H = 10 ± 1 / 0.8 Y = 20 / 0.6 F = 30 - 3 / 0.6 J = 30 - 3 / 0.8 S = 30 / 0.6 P = 45 ± 2 / 0.6 R = tape and reel L = tape and ammo VKP Series: CQ = 500 VAC, 760 VAC 12th digit (1) 0 = bulk Other = special type WKP Series: CP = 500 VAC, 760 VAC OTHER LEAD CONFIGURATION 10th digit Q = snap-in T = outside crimp U = 7.5 mm to 5 mm Y = inline wire SPECIALTY 10th digit R or S Note (1) The schematic of the 11th and 12th digit is only applicable if the 10th digit is B, C, D, or E. Revision: 21-Aug-15 Document Number: 22001 14 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay Roederstein ORDER CODE, 10th, 11th AND 12th DIGIT - POSSIBLE LEAD AND PACKAGING COMBINATIONS BULK PACKAGING LEAD LENGTH L 30 mm - 3 mm Straight leads 10 mm ± 1 mm 6 mm - 1 mm Preformed leads inside crimp 30 mm - 3 mm Preformed leads outside crimp 5 mm ± 1 mm Preformed leads snap-in Inline wire Min. 2.8 mm Min. 3.5 mm Min. 2.8 mm + 1.5 mm Min. 3.0 mm + 2.0 mm LEAD DIA. d 0.6 mm 0.8 mm 0.6 mm 0.8 mm 0.6 mm / 0.8 mm 0.6 mm 0.8 mm 0.6 mm 0.8 mm 0.6 mm 0.8 mm 0.6 mm 0.8 mm 5 mm BF0 BD0 BB0 BFG TA0 QA0 YA0 YB0 LEAD SPACING F 7.5 mm 10 mm CF0 DF0 CJ0 DJ0 CD0 DD0 CH0 DH0 CB0 DB0 CFG DFG CJG DJG TC0 TE0 TD0 TF0 QC0 QE0 QD0 QF0 YC0 YE0 YD0 YF0 12.5 mm EF0 EJ0 ED0 EH0 EB0 EFG EJG TG0 TH0 QG0 QH0 YG0 YH0 REEL PACKAGING COMPONENT PITCH 12.7 mm TAPING P Lead diameter 0.6 mm Lead spacing F Body diameter D Straight leads Preformed leads inside crimp Preformed leads outside crimp Preformed leads 7.5 mm to 5 mm Preformed leads snap-in Inline wire TAPING T TAPING U H = 18.0 mm straight leads only H = 20.0 mm H = 16.5 mm H0 = 16.0 mm preformed leads only 5 mm 7.5 mm 5 mm 7.5 mm 5 mm 7.5 mm Valid for 12 mm standard (> 12 mm to 13 mm on request) BRE CRE BRA CRA BRC CRC BRB CRB TAR TCR UAR QAR QCR YBR YCR - REEL PACKAGING COMPONENT PITCH 25.4 mm TAPING F Lead spacing F Body diameter D Straight leads Preformed leads inside crimp Preformed leads outside crimp Inline wire 5 mm 7.5 mm 10 mm CRT CRU CRY CRZ YRC DRT DRU DRY DRZ TDR YRD > 12 mm H = 16.5 mm H = 18.0 mm H = 20.0 mm H0 = 16.0 mm H0 = 16.0 mm H0 = 16.0 mm BRT BRU BRY BRZ YRB 12.5 mm All diameters ERT ERU ERY ERZ TER YRE Note • The lead diameter of the taped components is depending on the capacitance value and corresponds with the data given in the individual datasheets. AMMO PACKAGING COMPONENT PITCH 12.7 mm TAPING P Lead diameter 0.6 mm Lead spacing F Disc diameter D Straight leads Preformed leads inside crimp Preformed leads 7.5 mm to 5 mm Inline wire Revision: 21-Aug-15 TAPING T TAPING U H = 18.0 mm straight leads only H = 20.0 mm H = 16.5 mm H0 = 16.0 mm preformed leads only 5 mm 7.5 mm 5 mm 7.5 mm 5 mm 7.5 mm Valid for 12 mm standard (> 12 mm to 13 mm on request) BLE BLA CLA BLC BLB CLB UAL YAL YLC - Document Number: 22001 15 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000