General Information www.vishay.com Vishay BCcomponents Ceramic Disc, RFI and Safety Capacitors IN ACCORDANCE WITH IEC RECOMMENDATIONS CERAMIC CAPACITORS ARE SUBDIVIDED INTO TWO CLASSES: • CERAMIC CLASS 1 or low-K capacitors are mainly manufactured of titanium dioxide or magnesium silicate • CERAMIC CLASS 2 or high-K capacitors contain mostly alkaline titanates • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 MAIN FEATURES CLASS 1 CLASS 2 APPLICATION For temperature compensation of frequency discriminating circuits and filters, coupling and decoupling in high-frequency circuits where low losses and narrow capacitance tolerances are demanded. As RFI and safety capacitors. As coupling and decoupling capacitors for such application where higher losses and a reduced capacitance stability are required. As RFI and safety capacitors PROPERTIES Temperature dependence capacitance High stability of capacitance. Low dissipation factor up to higher frequencies. Defined temperature coefficient of capacitance, positive or negative, linear and reversible. High insulation resistance. No voltage dependence. High long-term stability of electrical values. High capacitance values with small dimensions. Non-linear dependence of capacitance on temperature. DC VOLTAGE Capacitance dependence None Increasing with DISSIPATION FACTOR TAN Max. 0.15 % (typical) Max. 3.5 % (typical) INSULATION RESISTANCE 10 G 1 G CAPACITANCE TOLERANCES < 10 pF: ± 0.25 pF, ± 0.5 pF, ± 1 pF 10 pF: ± 2 %, ± 5 %, ± 10 %, ± 20 % ± 10 %, ± 20 %, (+ 80/- 20) % RATED VOLTAGE Up to 6 kVDC Up to 6 kVDC STANDARDS AND SPECIFICATIONS GENERAL STANDARDS IEC 60062 Marking codes for resistors and capacitors IEC 60068 Basic environmental testing procedures SPECIAL STANDARDS FOR CERAMIC CAPACITORS EN 130600 and IEC 60384-8 Fixed capacitors of ceramic dielectric, class 1 EN 130700 and IEC 60384-9 Fixed capacitors of ceramic dielectric, class 2 STANDARD FOR SPECIAL APPLICATION PURPOSES CSA C22.2 EN 132400 IEC 60065 IEC 60384-14.3 RFI - and safety capacitors UL60384-14 VDE 0560, part 2’5.70 and VDE 0860/8.81 Revision: 31-Jul-15 Document Number: 28536 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay BCcomponents MEASURING AND TESTING CONDITIONS CLASS 1 CAPACITANCE AND DISSIPATION FACTOR INSULATION RESISTANCE TEMPERATURE DEPENDENCE CAPACITANCE C 1000 pF C 100 pF 1 kHz, 1 VRMS to 5 VRMS 1 kHz, 1.0 VRMS ± 0.2 VRMS C < 1000 pF C < 100 pF 1 MHz, 1 VRMS to 5 VRMS 1 MHz, 1.0 VRMS ± 0.2 VRMS Rated voltage < 100 V: measuring voltage = (10 ± 1) V 100 V to < 500 V: 500 V: Measuring time: Rated voltage 500 V: DIELECTRIC STRENGTH CLASS 2 > 500 V: Measuring time: measuring voltage = (100 ± 15) V measuring voltage = (500 ± 50) V 60 s ± 5 s Test voltage = 2.5 x UR measuring voltage = 1.5 x UR 2s Notes • Climatic test conditions: temperature 20 °C to 25 °C • Relative humidity 50 % to 70 % NOMINAL VALUE SERIES ACCORDING TO IEC 60063 E6 (± 20 % TOLERANCE) E12 (± 10 % TOLERANCE) E24 (± 5 % TOLERANCE) 100 100 100 - - 110 - 120 120 - - 130 150 150 150 - - 160 - 180 180 - - 200 220 220 220 - - 240 - 270 270 - - 300 330 330 330 - - 360 - 390 390 - - 430 470 470 470 - - 510 - 560 560 - - 620 680 680 680 - - 750 - 820 820 - - 910 Note • E6 values preferred Revision: 31-Jul-15 Document Number: 28536 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay BCcomponents CAPACITANCE CODING SYSTEM CAPACITANCE VALUE CODE CAPACITANCE VALUE p33 0.33 pF 3p3 3.3 pF 33p 33 pF 330p 330 pF n33 330 pF (0.33 nF) 3n3 3300 pF (3.3 nF) 33n 33 000 pF (33 nF) 330n 330 000 pF (330 nF) μ33 0.33 μF 3μ3 CAPACITANCE TOLERANCE RATED VOLTAGE CERAMIC DIELECTRIC 3.3 μF CODE LETTER C-TOLERANCE < 10 pF (pF) C-TOLERANCE 10 pF (%) C ± 0.25 - D ± 0.5 ± 0.5 G - ±2 J - ±5 K - ± 10 M - ± 20 Z - + 80/- 20 CLEAR TEXT CLASS 1 CLASS 2 NP0 (C0G) X7R N750 (U2J) Y5P SL0 Z5U S3N Z5V Y5V Y5U Note • The actual markings are given in detail on the respective datasheet. PRODUCTION CODE ACCORDING TO IEC 60062 • The production code is indicated with a 4 FIGURE CODE (YEAR/WEEK) • The 1st two figures indicate the year and the second two figures indicate the week. Examples: 18th Week 1998 = 9818 50th Week 1999 = 9950 32nd Week 2000 = 0032 41st Week 2001 = 0141 27th Week 2002 = 0227 22nd Week 2003 = 0322 15th Week 2004 = 0415 Revision: 31-Jul-15 Document Number: 28536 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay BCcomponents MARKING OF THE TEMPERATURE CHARACTERISTIC OF CAPACITANCE FOR CLASS 2 CERAMIC CAPACITORS According to EN 130700 or IEC 60384-9 2 D 3 Admissible capacitance change related to 20 °C over the entire temperature range Marking for class 2 ceramic capacitor DC VOLTAGE Temperature range: upper and lower temperature limits in °C WITHOUT WITH CODE LETTER TEMPERATURE RANGE CODE FIGURE ± 10 % + 10 %/- 15 % B -55 to +125 1 ± 20 % + 20 %/- 30 % C -55 to +85 2 + 20 %/- 30 % + 20 %/- 40 % D -40 to +85 3 + 22 %/ - 56 % + 22 %/- 70 % E -25 to +85 4 + 30 %/- 80 % + 30 %/- 90 % F -10 to +85 5 ± 15 % + 15 %/- 40 % R ± 15 % + 15 %/- 25 % X According to EIA Standard RS 198 Y Lower category temperature 5 S Upper category temperature Admissible capacitance change related to 25 °C over the entire temperature range TEMPERATURE CODE LETTER TEMPERATURE CODE FIGURE CHANGE CODE LETTER -55 °C X +45 °C 2 ±1% A -30 °C Y +65 °C 4 ± 1.5 % B +10 °C Z Revision: 31-Jul-15 +85 °C 5 ± 2.2 % C +105 °C 6 ± 3.3 % D +125 °C 7 ± 4.7 % E ± 7.5 % F ± 10 % P ± 15 % R ± 22 % S + 22 %/- 33 % T + 22 %/- 56 % U + 22 %/- 82 % V Document Number: 28536 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay BCcomponents CLASS 1 CERAMIC TYPE TEMPERATURE COEFFICIENT OF THE CAPACITANCE FOR CLASS 1 CERAMIC CAPACITORS C = capacitance change C -------- % = 100 x x C = temperature coefficient in 10-6/°C = temperature change in °C ΔC [%] C 3 40 30 20 2 1 0 0 NP0 (C0G) -10 -2 -20 -3 -30 -4 -40 350 0 SL0 -1000 20 40 60 80 100 120 140 160 Temperature (°C) N750 (U2J) -50 -55 -40 -20 0 20 40 60 80 100 120 85 υ u (°C) 20 40 60 80 100 120 85 υ u (°C) 1000 -2000 -60 -40 -20 0 10 -1 -5 -55 -40 -20 0 Capacitance Change ΔC/C (ppm) from +25 °C Reading N750 (U2J) Capacitance Change ΔC/C (%) NP0 (C0G) ΔC [%] C 50 5 4 60 40 20 0 -20 S3N -40 -60 -55 -40 -20 0 10 25 45 65 85 105125 150 Temperature (°C) VOLTAGE DEPENDENCE OF CAPACITANCE None FREQUENCY DEPENDENCE OF CAPACITANCE Max. -2 % at 10 MHz DISSIPATION FACTOR • For values greater than 50 pF: see datasheet • For lower values the dissipation factor is calculated according to the type of ceramic (rated temperature coefficient) under consideration of the capacitance acc. to EN 130600. • The dissipation factor as well as the measuring method to be agreed between manufacturer and user for values lower than 5 pF. Revision: 31-Jul-15 Document Number: 28536 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay BCcomponents CLASS 2 CERAMIC TYPE Ceramic Dielectric: X7R Ceramic Dielectric: Y5P Typical % Capacitance Change at 25 °C Typical % Capacitance Change at 25 °C 20 Capacitance Change ΔC/C (%) Capacitance Change ΔC/C (%) 10 5 Y5P 0 -5 -10 -15 -20 -35 -15 5 25 45 65 15 10 5 -5 -10 -15 -20 -55 85 X7R 0 -35 -15 5 25 45 65 85 105 125 Temperature °C Temperature °C Ceramic Dielectric: X5F Ceramic Dielectric: Z5U/Z5V Typical % Capacitance Change at 25 °C Typical % Capacitance Change at 25 °C 0 -10 Capacitance Change ΔC/C (%) Capacitance Change ΔC/C (%) 10 Z5U -20 -30 -40 - 50 - 60 Z5V - 70 - 80 - 90 -35 -15 5 25 45 65 6.5 4.5 X5F 2.5 0.5 -1.5 -3.5 -5.5 -55 85 -35 -15 25 45 65 85 Ceramic Dielectric: Y5U Ceramic Dielectric: Y5V Typical % Capacitance Change at 25 °C Typical % Capacitance Change at 25 °C 10 10 0 Y5V -10 -20 -30 -40 -50 -60 -70 -80 -90 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 Temperature °C Revision: 31-Jul-15 Capacitance Change ΔC/C (%) Capacitance Change ΔC/C (%) 5 Temperature °C Temperature °C Y5U 0 -10 -20 -30 -40 -50 -60 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 Temperature °C Document Number: 28536 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay BCcomponents CAPACITANCE “AGING” OF CERAMIC CAPACITORS Following the final heat treatment, all class 2 ceramic capacitors reduce their capacitance value. According to logarithmic law, this is due to their special crystalline construction. This change is called “aging”. If the capacitors are heat treated (for example when soldering), the capacitance increases again to a higher value deaging, and the aging process begins again. Note • The level of this deaging is dependent on the temperature and the duration of the heat; an almost complete deaging is achieved at 150 °C in one hour. These conditions also form the basis for reference measurements when testing. The capacitance change per time decade (aging constant) differs for the various types of ceramic, but typical values can be taken from the equations below. 100 x C 11 - C 12 k = ----------------------------------------------C 11 x log 10 t 2 /t 1 t1, t2 = measuring time point (h) C11, C12 = capacitance values for the times t1, t2 k = aging constant (%) C 12 = C 11 x 1 - k/100 x log 10 t 2 /t 1 REFERENCE MEASUREMENT Due to aging, it is necessary to quote an age for reference measurements which can be related to the capacitance with fixed tolerance. According to EN 130700, this time period is 1000 h. In order to avoid the influence of aging, it is important to deage the capacitors before stress-testing. The following procedure is adopted (see also EN 130700): Deaging at 125 °C, 1 h Storage for 24 h at normal climate temperature Initial measurement Stress Deaging at 125 °C, 1 h Storage for 24 h at normal climate temperature Final measurement Revision: 31-Jul-15 Document Number: 28536 7 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay BCcomponents COMPONENT CLIMATIC CATEGORY 40/085/21 1st SET 2nd SET 3rd SET Minimum ambient temperature of operation (test cold) Maximum ambient temperature of operation (dry heat test) Number of days (steady test state) The large number of possible combinations of tests and severities may be reduced by the selection of a few standard groupings according to IEC 60068-1. Category examples according to IEC 60068-1 25/085/04 25/085/21 40/085/21 55/125/21 First set: two digits denoting the minimum ambient temperature of operation (cold test). Second set: three digits denoting the maximum ambient temperature (dry heat test). Third set: two digits denoting the number of days of the damp heat steady state test (Ca). Revision: 31-Jul-15 65 -65 °C 55 -55 °C 40 -40 °C 25 -25 °C 10 -10 °C 00 0 °C 05 +5 °C 155 +155 °C 125 +125 °C 110 +110 °C 090 +90 °C 085 +85 °C 080 +80 °C 075 +75 °C 070 +70 °C 065 +65 °C 060 +60 °C 055 +55 °C 56 56 days 21 21 days 10 10 days 04 4 days 00 The component is not required to be exposed to damp heat 56 days Document Number: 28536 8 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay BCcomponents STORAGE The capacitors must not be stored in a corrosive atmosphere, where sulphide or chloride gas, acid, alkali or salt are present. Exposure of the components to moisture, should be avoided. The solderability of the leads is not affected by storage of up to 24 months (temperature +10 °C to +40 °C, relative humidity up to 60 % RH). Class 2 ceramic dielectric capacitors are also subject to aging see previous page. SOLDERING SOLDERING SPECIFICATIONS Soldering test for capacitors with wire leads: (according to IEC 60068-2-20, solder bath method) Soldering temperature Soldering duration Distance from component body SOLDERABILITY RESISTANCE TO SOLDERING HEAT (235 ± 5) °C (260 ± 5) °C (2 ± 0.5) s (10 ± 1) s 2 mm 5 mm SOLDERING RECOMMENDATIONS Soldering of the component should be achieved using a Sn96.5/Ag3.0/Cu0.5, a Sn60/40 type or a silver-bearing Sn type solder. Ceramic capacitors are very sensitive to rapid changes in temperature (Thermal shock) therefore the solder heat resistance specification (see above table) should not be exceeded. Subjecting the capacitor to excessive heating may result in thermal shocks that can crack the ceramic body. Similarly, excessive heating can cause the internal solder junction to melt. CLEANING The components should be cleaned immediately following the soldering operation with vapor degreasers. SOLVENT RESISTANCE The coating and marking of the capacitors are resistant to the following test method: IEC 60068-2-45 (method XA) MOUNTING We do not recommend modifying the lead terminals, e.g. bending or cropping. This action could break the coating or crack the ceramic insert. If however, the lead must be modified in any way, we recommend support of the lead with a clamping fixture next to the coating. Revision: 31-Jul-15 Document Number: 28536 9 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay BCcomponents AQL/FIT VALUES/SUPPLIED QUALITY AQL 0.1 for the Sum of the Electric Main Faults • C-tolerance > 1.5 x tolerance limit • DF > 1.5 x catalog value • RIS < catalog value • Inadequate dielectric breakdown • Interruption AQL 0.25 for the Sum of the Mechanical Main Faults • Marking wrong or missing • Dimensions out of tolerance • Coating failure • Lead space out of tolerance • Poor solderability of leads • Wrong lead length AQL 0.65 for Secondary Faults • Coating extension out of tolerance • Marking incomplete • Tape dimensions out of tolerance • Testing in accordance to IEC 60410 Notes The following agreements are possible on request: • Lower AQL values • Confirmed initial random sampling test with appropriate report • Report on production test findings • Agreement on ppm concept RELIABILITY By careful control of the manufacturing process stages, the quality of the product is maintained at the highest possible level. To obtain data on the reliability of our ceramic capacitors, many long-term tests under increased temperature and voltage conditions have been carried out in our laboratories. Based on the results of these tests, the following can be stated: Reference conditions: ambient temperature: (40 ± 2) °C relative humidity: 90 % to 95 % electrical stress: 0 V rated voltage (UR), RFI safety cap 100 % UR Failure criteria: Failure tests: short circuit (R 1 G) or short circuit (R 3 G RFI safety caps) class 1 capacitors: l = 500 FIT class 2 capacitors: l = 500 FIT By derating the voltage load, greatly increased reliability can be predicted. Temperature, up to the maximum category temperature, is not believed to significantly affect the reliability. Revision: 31-Jul-15 Document Number: 28536 10 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay BCcomponents PRODUCTION FLOWCHART QC 1 Pressing discs PC 1 Sinter process (firing) PC 2 QC 2 Screen printing of both electrodes Firing of electrodes PC 3 Sorting in tolerance classes if necessary PC 4 QC 3 PC 5 Forming and soldering leads Aligning for coating process Epoxy or phenol resin coating PC 6 Hardening resin coat Marking 100 % test C-value Dissipation factor Voltage test PC 7 Visual inspection QC 4 Cutting leads for bulk packaging or taping PC 8, 9 Packaging QC 5 Delivery Revision: 31-Jul-15 PC = Production control QC = Quality control Document Number: 28536 11 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay BCcomponents STANDARD LEAD CONFIGURATIONS D D Tangent line L = straight leads K = outside crimp kinked leads J = inside crimp kinked leads Tangent line SH D SH Tangent line DR F F F V = inline kinked leads D T D = diameter F = lead spacing SH = seated height T = thickness L = lead length DR = run down SH F L Ød NON-STANDARD LEAD STYLES AVAILABLE ON REQUEST T = double crimp leads D T SH L F Revision: 31-Jul-15 Document Number: 28536 12 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay BCcomponents PACKAGING RADIAL TAPE AND AMMOPACK DESCRIPTION Body dimension Feed hole diameter Wire lead diameter Lead end protrusion Lead spacing Height to seating plane (for straight leads) Height to seating plane (for kinked leads) Top of component height Body inclination Rejected component cut height Component pitch Feed hole pitch Feed hole off alignment Plane deviation Overall tape thickness Overall tape and lead thickness Carrier tape width Adhesive tape width Feed hole height off alignment Adhesive tape margin Reference drawing CODE 5.0 mm LEAD SPACING 12.7 mm FEED HOLE PITCH 7.5 mm LEAD SPACING 15.0 mm FEED HOLE PITCH D D0 d e F 11.0 max. 4.0 ± 0.2 0.6 ± 0.05 1.0 max. 5.0 + 0.6/- 0.4 14.0 max. 4.0 ± 0.2 0.6 ± 0.05 1.0 max. 7.5 + 0.6/- 0.4 H0 20.0 ± 0.5 20.0 ± 0.5 H0 16.0 ± 0.5 16.0 ± 0.5 H1 h L p P0 P1 P2 P t t1 W W0 W1 W2 32.0 max. 0 ± 1.0 11.0 max. 12.7 ± 1.0 12.7 ± 0.3 3.85 ± 0.7 6.35 ± 1.3 1.0 max. 0.9 max. 1.5 max. 18.0 + 1.0/- 0.5 5.0 min. 9.0 + 0.75/- 0.5 3.0 max. Fig. 1 40.0 max. 0 ± 1.0 11.0 max. 15.0 ± 1.0 15.0 ± 0.3 3.75 ± 0.7 7.5 ± 1.5 1.0 max. 0.9 max. 1.5 max. 18.0 + 1.0/- 0.5 5.0 min. 9.0 + 0.75/- 0.5 3.0 max. Fig. 1 CODE 7.5 mm LEAD SPACING 12.7 mm FEED HOLE PITCH 25.4 mm COMPONENT PITCH 10.0 mm LEAD SPACING 15.0 mm FEED HOLE PITCH 25.4 mm COMPONENT PITCH D D0 d e F 22.0 max. 4.0 ± 0.2 0.6 ± 0.05 1.0 max. 7.5 + 0.6/- 0.4 22.0 max. 4.0 ± 0.2 0.8 ± 0.05 1.0 max. 10.0 + 0.6/- 0.4 H0 20.0 ± 0.5 20.0 ± 0.5 H0 16.0 ± 0.5 16.0 ± 0.5 H1 h L p P0 P1 P2 P t t1 W W0 W1 W2 43.0 max. 0 ± 1.0 11.0 max. 25.4 ± 1.0 12.7 ± 0.3 8.9 ± 0.7 12.7 ± 1.5 1.0 max. 0.9 max. 1.5 max. 18.0 + 1.0/- 0.5 5.0 min. 9.0 + 0.75/- 0.5 3.0 max. Fig. 2 43.0 max. 0 ± 1.0 11.0 max. 25.4 ± 1.0 12.7 ± 0.3 8.9 ± 0.7 12.7 ± 1.5 1.0 max. 0.9 max. 1.7 max. 18.0 + 1.0/- 0.5 5.0 min. 9.0 + 0.75/- 0.5 3.0 max. Fig. 2 PACKAGING RADIAL TAPE AND AMMOPACK DESCRIPTION Body dimension Feed hole diameter Wire lead diameter Lead end protrusion Lead spacing Height to seating plane (for straight leads) Height to seating plane (for kinked leads) Top of component height Body inclination Rejected component cut height Component pitch Feed hole pitch Feed hole off alignment Plane deviation Overall tape thickness Overall tape and lead thickness Carrier tape width Adhesive tape width Feed hole height off alignment Adhesive tape margin Reference drawing Revision: 31-Jul-15 Document Number: 28536 13 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay BCcomponents PACKAGING VERSIONS Reel Packaging Ammo Packaging direction of unreeling Ø 16 ± 1 340 max. 350 max. 60 max. 340 max. 55 max. P2 P ΔP Δh ΔP H1 P Δh D W2 P2 ΔP ΔP Δh T Δh H1 F H0 Ød W1 W W0 Ød Direction of unreeling P1 F P0 D0 W2 W1 W W0 L A H0 A e e t1 Detail A t P0 P1 F D0 t1 t Detail A Fig. 1 - Illustration for component pitch 12.7 mm and 15.0 mm Feed hole pitch 12.7 mm and 15.0 mm (12.7 mm for F = 5.0 mm and 6.4 mm; 15 mm for F = 7.5 mm) Revision: 31-Jul-15 Fig. 2 - Illustration for component pitch 25.4 mm Feed hole pitch 12.7 mm (for F = 7.5 mm, 10.0 mm and 12.5 mm) Document Number: 28536 14 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay BCcomponents CLEAR TEXT ORDERING CODE D 471 K 20 Y5P L 6 3 J 5 R 1 234 5 67 8 9 10 11 12 13 14 15 16 Size Code Temperature Characteristic Rated Voltage Please see “size code” table Please see the temperature coefficient curve of ceramic type Product Type Capacitance Capacitance Tolerance D = general The first two type with digits are the significant phenolic figures of resin coat capacitance S = general and the last digit is a type with epoxy resin multiplier as follows: coat 0=x1 1 = x 10 F = low dissipation 2 = x 100 3 = x 1000 type 4 = x 10 000 9 = x 0.1 VY1 = safety recognized with epoxy resin coat C = ± 0.25 pF D = ± 0.5 pF G=±2% J=±5% K = ± 10 % M = ± 20 % Z = + 80 %/ - 20 % VY2 = safety recognized with epoxy resin coat H = HV disc X7R Lead Packaging/ Diameter Lead Length 6= F = 50 V H = 100 V 0.6 mm L = 500 V ± 0.05 mm N = 1 kV P = 2 kV 8= R = 3 kV 0.8 mm U = 6 kV ± 0.05 mm 3 = bulk 30 mm ± 5.0 mm S = X1/Y2 300 V (AC) T = tape and reel Q = X1/Y1 500 V (AC) U= ammopack For VY1: G = X1/Y1 500 V (AC) HF 5 = bulk 5.0 mm ± 0.8 mm Lead Style Lead RoHSSpacing Compliant Please see 2= “lead 2.5 mm configurations” 5= 5.0 mm 6= 6.4 mm 7= 7.5 mm 0= 10.0 mm X= 12.5 mm For VY1*C: C = X1/Y1 500 V (AC) HF, compact size For VY2: G = X1/Y2 300 V (AC) HF Note • HF = RoHS-compliant and halogen-free. LABELING Each reel is provided with a label showing the following details: Manufacturer, capacitance, tolerance, batch number, quantity of components, rated voltage and dielectric. On special request other designations can be shown. For example: Revision: 31-Jul-15 Document Number: 28536 15 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay BCcomponents SMALLEST PACKAGING QUANTITIES (SPQ) STANDARD PACKAGING SPEC. PACKAGING PRODUCT FAMILY (D) Disc cap; long lead; (L 25.4 mm) SIZE CODE LEAD SPACE (F) 1000 29 to 39 1000 43 to 47 53 to 75 All (except 6 kV) All 6 kV 5000 All All 250 39 to 47 2000 53 to 59 1000 84 250 6.4 mm < 500 VDC 2500 500 WV 2000 VDC 2000 3000 VDC 1000 7.5 mm 59 47 Disc cap 6.4 mm All 7.5 mm 7.5 mm 53 59 All 6.4 mm > 7.5 mm 370 x 370 x 60 500 All 500 < 500 VDC 2000 500 WV < 2000 VDC 2000 2000 VDC and 3000 VDC 1500 500 1500 All 7.5 mm 7.5 mm 500 1000 > 7.5 mm 6.4 mm 245 x 120 x 65 1000 7.5 mm 53 Revision: 31-Jul-15 All 500 All Safety disc All 63 to 75 53 245 x 120 x 65 500 3000 53 Ammopack 1000 96 Disc cap Safety disc 2000 20 to 33 47 Tape and reel 250 3000 63 to 84 Safety disc; short lead; (L 10 mm) 500 20 to 25 53 to 59 245 x 120 x 65 250 29 to 39 43 to 47 BOX DIMENSIONS L x W x H (mm) 1000 500 84 to 96 53 to 75 Disc cap; short lead; (L 10 mm) SPQ (PCS) 20 to 25 39 to 49 Bulk WORKING VOLTAGE (W) 1500 1000 335 x 240 x 50 335 x 290 x 50 360 x 330 x 55 335 x 290 x 50 1000 All 750 750 360 x 330 x 55 Document Number: 28536 16 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay BCcomponents SIZE CODE SIZE CODE (CTC) DISC DIAMETER (OUTPUT) 20 5.0 mm max. 25 6.5 mm max. 29 7.5 mm max. 31 8.0 mm max. 33 8.5 mm max. 35 8.9 mm max. 39 10.0 mm max. 41 10.5 mm max. 43 11.0 mm max. 47 12.0 mm max. 49 12.5 mm max. 51 13.0 mm max. 53 13.5 mm max. 59 15.0 mm max. 61 15.5 mm max. 65 16.5 mm max. 69 17.5 mm max. 75 19.0 mm max. 84 21.5 mm max. 93 23.6 mm max. 96 24.5 mm max. MEASUREMENT On the basis of the center of the product, measure the thickness with vernier caliper along every direction. Calipering position refers to the figure below. The maximum value is the thickness value. T D max. Vernier Caliper position for the thickness measurement Vernier Caliper position for the diameter measurement Revision: 31-Jul-15 Document Number: 28536 17 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 General Information www.vishay.com Vishay BCcomponents CAUTION 1. OPERATING VOLTAGE AND FREQUENCY CHARACTERISTIC When sinusiodal or ripple voltage applied to DC ceramic disc capacitors, be sure to maintain the peak-to-peak value or the peak value of the sum of both AC + DC within the rated voltage. When start or stop applying the voltage, resonance may generate irregular voltage. When rectangular or pulse wave voltage is applied to DC ceramic disc capacitors, the self-heating generated by the capacitor is higher than the sinusoidal application with the same frequency. The allowable voltage rating for the rectangular or pulse wave corresponds approximately with the allowable voltage of a sinusoidal wave with the double fundamental frequency. The allowable voltage varies, depending on the voltage and the waveform. Diagrams of the limiting values are available for each capacitor series on request. VOLTAGE Waveform figure DC V0-p DC + AC Vp-p V0-p 0 AC 0 0 2. OPERATING TEMPERATURE AND SELF-GENERATED HEAT The surface temperature of the capacitors must not exceed the upper limit of its rated operating temperature. During operation in a high-frequency circuit or a pulse signal circuit, the capacitor itself generate heat due to dielectric losses. Applied voltage should be the load such as self-generated heat is within 20 °C on the condition of environmental temperature 25 °C. Note, that excessive heat may lead to deterioration of the capacitor’s characteristics. Revision: 31-Jul-15 Document Number: 28536 18 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000