Download Data Sheet

Rev. A
PSDN-10 Series
10 Watt
Single Output
AC/DC DIN Rail Power Supply
FEATURES
● Single Output
● UL1310 Class 2 Power Unit / LPS Pass
● Brown Out Protection
● High Operating Temperature up to 70°C
● True DC OK Signal Output
● UL508 (Industrial Control Equipment) Listed
● Withstand 5G Vibration Test
● High Efficiency, Long Life, and High Reliability
● Universal AC Input 88~264VAC
● All Using 105°C Long Life Electrolytic Capacitors
● Installed on DIN Rail TS35 / 7.5 or 15
● Short Circuit, Over Load, and Over Voltage Protection
DESCRIPTION
The PSDN-10 series of AC/DC DIN Rail power supplies provides 10 Watts of continuous output power. All models have a
single output and a universal input range. All models are over load, over voltage, and short circuit protected.
SPECIFICATIONS: PSDN-10 Series
All specifications are based on 25°C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted.
We reserve the right to change specifications based on technological advances.
INPUT SPECIFICATIONS
Input Voltage Range (See Note 3)
88 ~ 264VAC or 124 ~ 370VDC
Input Frequency
47 to 63Hz
AC Current (typical)
0.23A at 115VAC 0.17A at 230VAC
Inrush Current (typical)
15A at 115VAC
30A at 230VAC
Leakage Current
< 1mA at 230VAC
OUTPUT SPECIFICATIONS
Output Voltage
See Table
Output Power
See Table
Output Voltage Adjustability
±10%
Voltage Tolerance (See Note 2)
±1%
Line Regulation
±1%
Load Regulation
±1%
Output Current
See Table
Ripple & Noise (See Note 1)
See Table
Setup, Rise Time
< 800ms, <50ms @ 230VAC and full load
Hold Up Time (typical)
> 16ms at 115VAC and full load, > 32ms at 230VAC and full load
PROTECTION
115% ~ 150% rated output voltage
Over Voltage Protection
Protection Type: Latch-off mode
> 105°C rated output power
Over Load Protection
Protection type: constant current limiting, automatically after fault condition is removed.
GENERAL SPECIFICATIONS
Efficiency
See Table
Withstand Voltage
I/P - O/P: 3KVAC (4242VDC), I/P - FG: 1.5KVAC (2121VDC) for 1 minute
Isolation Resistance
I/P - O/P, I/P - FG, O/P - FG: 100MΩ / 500VDC
DC OK Signal
Open collector max 40mA
ENVIRONMENTAL SPECIFICATIONS
Working Temperature
-20°C ~ +70°C (refer to output load derating curve)
Storage Temperature
-40°C ~ +85°C
Working Humidity
20% ~ 90% RH, non-condensing
Storage Humidity
10% ~ 95% RH
Vibration
10 ~ 500Hz, 5G 0.5Oct/min, period for 60 min., Each along X,Y,Z axes.
Cooling
Free Air Convection
Temperature Coefficient
±0.03% / °C (0 ~ 50°C)
MTBF (MIL-HDBK-217F)
See Table
PHYSICAL SPECIFICATIONS
Packing
0.18Kg
Dimensions (W x H x D)
0.91 x 3.54 x 3.90 inches (23 x 90 x 99 mm)
Connection
I/P: 3 poles, O/P: 3 poles screw DIN terminal
SAFETY & EMC (See Note 4)
Safety Standards
UL 508, TUV EN60950-1, UL1310 NEC class 2 compliant
EMI Conduction & Radiation
EN55022: 2006 (Class B), EN61204-3: 2000, EN61000-6-3: 2007
Harmonic Current
EN61000-3-2,3: 2006
EMS Immunity
EN55024, EN61204-3: 2000, EN61000-6-1: 2007 (EN61000-4-2,3,4,5,6,8,11)
Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833
603-778-2300 www.wallindustries.com Fax 603-778-9797
PSDN-10 Series
10 Watt
Single Output
AC/DC DIN Rail Power Supply
Rev. A
MODEL SELECTION TABLE
Model Number Input Voltage
Output
Voltage
Output
Current
Rated Output
Power
PSDN-10-12
88 ~ 264VAC
(124 ~ 370VDC)
12 VDC
0.84A
10.08W
PSDN-10-15
88 ~ 264VAC
(124 ~ 370VDC)
15 VDC
0.67A
PSDN-10-24
88 ~ 264VAC
(124 ~ 370VDC)
24 VDC
0.42A
Ripple & Noise
(1)
MTBF
Efficiency
100mVp-p
120,400 hours
83%
10.05W
100mVp-p
131,300 hours
85%
10.08W
120mVp-p
125,900 hours
86%
NOTES
1. Ripple & noise is measured at 20MHz bandwidth by using a 12" twisted pair-wire terminated with a 0.1µF & 47µF capacitors
in parallel.
2. Tolerance includes set up tolerance, line regulation, and load regulation.
3. Derating may be needed under low input voltages. Please check the derating curve for more details.
4. The power supply is considered a component, which will be installed into final equipment. The final equipment must be
re-confirmed that it still meets EMC directives.
5. In parallel connection only one unit may operate if the total output load is less than 5% of the rated load.
BLOCK DIAGRAM
APPLICATIONS OF DC OK ACTIVE SIGNAL
(a) 5V Signal
(b) LED
Model
12V
15V
24V
R
≥ 1.5KΩ
≥ 2KΩ
≥ 3.9KΩ
(c) Relay
Model
12V
15V
24V
R
≥ 2.4KΩ
≥ 3KΩ
≥ 4.7KΩ
Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833
603-778-2300 www.wallindustries.com Fax 603-778-9797
Model
12V
15V
24V
R
≥ 700Ω
≥ 700Ω
≥ 1.2KΩ
PSDN-10 Series
10 Watt
Single Output
AC/DC DIN Rail Power Supply
Rev. A
DERATING CURVES
Load vs Temperature
Load vs Input Voltage
Ta=25°C
100
100
90
Load (%)
Load (%)
80
60
40
80
70
60
50
20
-20
40
0
10
20
30
40
50
60
70
Ambient Temperature (°C)
85
100
110
MECHANICAL DRAWING
Unit: inches (mm)
0.91 (23)
1.38 (35)
0.20 0.20
(5) (5)
3.54 (90)
Install DIN Rail TS35/7.5 or TS35/15
120
Input Voltage (VAC) 60Hz
0.20 0.20
(5) (5)
Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833
603-778-2300 www.wallindustries.com Fax 603-778-9797
3.90 (99)
264