DLA 10004 Datasheet

DLA 10004
www.vishay.com
Vishay
DLA 10004 SuperTan® Extended Capacitance,
Wet Tantalum Capacitors with Hermetic Seal
FEATURES
• Ultra high capacitance
• All tantalum, hermetically sealed case
• Utilizes proven Vishay SuperTan® technology
• High and stable capacitance
• High reliability, rugged design
• Axial through-hole terminations: standard tin / lead (Sn / Pb)
PERFORMANCE CHARACTERISTICS
Operating Temperature: -55 °C to +85 °C
(to +125 °C with voltage derating)
Capacitance Tolerance: at 120 Hz, +25 °C. ± 20 %
standard. ± 10 % available as special.
DC Leakage Current (DCL Max.): at +25 °C and above:
leakage current shall not exceed the values listed in the
Standard Ratings tables.
Life Test: capacitors are capable of withstanding a 2000 h
life test at a temperature of +85 °C at the applicable rated
DC working voltage.
ORDERING INFORMATION
10004
-29
K
DLA DRAWING NUMBER
DASH NUMBER
CAPACITANCE TOLERANCE
S
K = ± 10 %
M = ± 20 %
DLA LAND AND MARITIME
COLUMBUS, OHIO
S = sleeved
U = unsleeved
Drawing no.
10004
DIMENSIONS in inches [millimeters]
Terminal Welded
to Case
0.250 (6.35)
Max.
0.0253 ± 0.002 [0.64 ± 0.05] dia.
(no. 22 AWG) tinned nickel leads
solderable and weldable
0.094 (2.38)
Max.
E
L
E
“D” Dia.
Terminal Location
within 0.031 of Center
CASE CODE
D ± 0.016 [0.41]
MAX. INSULATED
(DIA.)
L1 + 0.031 [0.79] UNINSULATED
E ± 0.250 [6.35] MAX.
T1
0.188 [4.78]
0.219 [5.56]
0.453 [11.51]
1.500 [38.10]
T2
0.281 [7.14]
0.312 [7.92]
0.641 [16.28]
2.250 [57.15]
T3
0.375 [9.52]
0.406 [10.31]
0.766 [19.46]
2.250 [57.15]
T4
0.375 [9.52]
0.406 [10.31]
1.062 [26.97]
2.250 [57.15]
Notes
• Material at egress is Tantalum
• Insulation sleeving will lap over the ends of the capacitor case
Revision: 14-Mar-16
• Approx. weight
T1: 2.3 g, T2: 5.7 g
T3: 9.4 g, T4: 14.8 g
Document Number: 40137
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DLA 10004
www.vishay.com
Vishay
STANDARD RATINGS
CAPACITANCE
(μF)
TYP.
MAX.
CASE ESR AT ESR AT
VOLTAGE
1 kHz
CODE 120 Hz
()
()
MAX. DCL AT
+25 °C
(μA)
+85 °C/
+125 °C
(μA)
MAX. CAPACITANCE
CHANGE AT
-55 °C
(%)
+85 °C
(%)
+125 °C
(%)
Z
-55 °C
()
AC
RIPPLE
85 °C
40 kHz
mA
RMS
PART
NUMBER
10 VDC AT +85 ºC, SURGE = 11.5 VDC; 7 VDC AT +125 ºC
4700
10
T3
0.35
< 0.200
16
100
-80
10
20
3.50
4000
10004-01(1)(2)
10 000
10
T4
0.25
< 0.100
25
150
-85
20
35
3.00
5000
10004-02(1)(2)
3300
16
T3
0.35
< 0.200
16
100
-80
10
15
3.50
4000
10004-03(1)(2)
6000
16
T4
0.30
< 0.150
25
150
-80
15
20
3.00
4500
10004-04(1)(2)
5.00
4250
10004-05(1)(2)
16 VDC AT +85 ºC, SURGE = 18.4 VDC; 11 VDC AT +125 ºC
25 VDC AT +85 ºC, SURGE = 28.8 VDC; 15 VDC AT +125 ºC
4000
25
T4
0.35
< 0.150
25
125
-80
15
20
30 VDC AT +85 ºC, SURGE = 34.5 VDC; 20 VDC AT +125 ºC
820
30
T2
1.00
< 0.600
3.5
18
-75
12
20
20.00
1650
10004-32(1)(2)
3300
30
T4
0.35
< 0.200
25
125
-80
20
25
4.00
2750
10004-06(1)(2)
4.50
4000
10004-07(1)(2)
10004-33(1)(2)
35 VDC AT +85 ºC, SURGE = 40.3 VDC; 22 VDC AT +125 ºC
2800
35
T4
0.35
< 0.200
25
125
-80
20
30
50 VDC AT +85 ºC, SURGE = 57.5 VDC; 30 VDC AT +125 ºC
110
50
T1
1.60
< 1.000
2
7.5
-40
10
15
40.00
1500
900
50
T3
0.90
< 0.300
15
125
-75
20
20
10.00
2500
10004-34(1)(2)
1500
50
T3
1.00
< 0.300
25
130
-85
25
30
8.00
2400
10004-35(1)(2)
1500
50
T4
0.35
< 0.215
15
110
-70
20
20
6.00
3500
10004-08(1)(2)
2200
50
T4
0.60
< 0.400
25
125
-80
25
30
4.50
3000
10004-15(1)(2)
10004-31(1)(2)
60 VDC AT +85 ºC, SURGE = 69 VDC; 40 VDC AT +125 ºC
68
60
T1
1.50
< 0.600
1.5
7.5
-30
10
12
40.00
1400
560
60
T3
0.90
< 0.300
20
120
-70
12
15
10.00
2500
10004-36(1)(2)
1000
60
T4
0.50
< 0.300
20
120
-40
10
15
5.50
3500
10004-09(1)(2)
180
75
T2
1.50
< 0.500
5
25
-35
15
20
30.00
2000
10004-10(1)(2)
470
75
T3
0.60
< 0.325
25
100
-45
10
25
10.00
3000
10004-11(1)(2)
750
75
T4
0.50
< 0.400
20
120
-35
10
15
6.50
3500
10004-12(1)(2)
940
75
T4
0.50
< 0.350
20
200
-60
12
20
8.00
3500
10004-17(1)(2)
100.00
1200
10004-37(1)(2)
75 VDC AT +85 ºC, SURGE = 86.3 VDC; 50 VDC AT +125 ºC
100 VDC AT +85 ºC, SURGE = 115 VDC; 65 VDC AT +125 ºC
22
100
T1
3.00
< 1.500
1
5
-15
4
220
100
T3
1.40
< 0.200
5
400
100
T4
0.70
< 0.400
10
470
100
T4
0.70
< 0.500
25
250
10
25
-55
10
15
18.00
2500
10004-38(1)(2)
120
-40
6
12
15.00
3000
10004-13(1)(2)
-50
10
20
10
3500
10004-18(1)(2)
20.00
2500
10004-14(1)(2)
125 VDC AT +85 ºC, SURGE = 144 VDC; 85 VDC AT +125 ºC
240
125
T4
0.80
< 0.600
15
150
-35
6
12
Note
• Part number definitions:
(1) K = 10 %
M = 20 %
(2) S = sleeved or insulated
U = unsleeved
Revision: 14-Mar-16
Document Number: 40137
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DLA 10004
www.vishay.com
Vishay
RIPPLE CURRENT MULTIPLIERS VS. FREQUENCY, TEMPERATURE AND APPLIES PEAK VOLTAGE
FREQUENCYOF
APPLIED RIPPLE
CURRENT
120 Hz
800 Hz
1 kHz
10 kHz
40 kHz
100 kHz
AMBIENT STILL
 55 85 105 125  55 85 105 125  55 85 105 125  55 85 105 125  55 85 105 125  55 85 105 125
AIR TEMP. IN °C
% of
85 °C
rated
peak
voltage
100 % 0.60 0.39
-
-
0.71 0.43
-
-
0.72 0.46
-
-
0.88 0.55
-
-
1.0 0.63
-
-
1.1 0.69
-
-
90 %
0.60 0.46
-
-
0.71 0.55
-
-
0.72 0.55
-
-
0.88 0.67
-
-
1.0 0.77
-
-
1.1 0.85
-
-
80 %
0.60 0.52 0.35
-
0.71 0.62 0.42
-
0.72 0.62 0.42
-
0.88 0.76 0.52
-
1.0 0.87 0.59
-
1.1 0.96 0.65
-
70 %
0.60 0.58 0.44
-
0.71 0.69 0.52
-
0.72 0.70 0.52
-
0.88 0.85 0.64
-
1.0 0.97 0.73
-
1.1 1.07 0.80
-
66 2/3 % 0.60 0.60 0.46 0.27 0.71 0.71 0.55 0.32 0.72 0.72 0.55 0.32 0.88 0.88 0.68 0.40 1.0 1.0 0.77 0.45 1.1 1.1 0.85 0.50
TYPICAL PERFORMANCE CHARACTERISTICS OF DLA 10004 CAPACITORS
ELECTRICAL CHARACTERISTICS
ITEM
PERFORMANCE CHARACTERISTICS
Operating Temperature Range
-55 °C to +85 °C (to +125 °C with voltage derating)
Capacitor Tolerance
± 20 %, ± 10 % at 120 Hz, at +25 °C
Capacitor Change by Temperature
Limit per Standard Ratings table
ESR
Limit per Standard Ratings table, at +25 °C, 120 Hz
Impedance
Limit per Standard Ratings table, at -55 °C, 120 Hz
DCL (Leakage Current)
Limit per Standard Ratings table
AC Ripply Current
Limit per Standard Ratings table, at +85 °C and 40 kHz
There shall be no continuous reverse voltage. Transient reverse voltages are acceptable under the
following conditions:
Reverse Voltage
Surge Voltage
a) The peak reverse voltage is equal to or less than 1.5 V and the product of the peak current times
the duration of the reverse transient is 0.05 ampere-second or less.
b) The repetition rate of the reverse voltage surges is less than 10 Hz.
Surge voltage shall be in accordance with MIL-PRF-39006 and DLA10004.
The DC rated surge voltage is the maximum voltage to which the capacitors can be subjected under
any conditions including transients and peak ripple at the highest line voltage.
The DC surge voltage is 115 % of rated DC voltage.
PERFORMANCE CHARACTERISTICS
ITEM
PERFORMANCE CHARACTERISTICS
Capacitors shall be capable of withstanding a 2000 h life test at a temperature +85 °C at rated
voltage, or a 1000 h life test at 125 °C test at derated voltage.
After the test, the capacitors shall meet the following requirements:
Life Testing
a) DC leakage at 85 °C and 125 °C shall not exceed 125 % of the specified value
b) DC leakage at 25 °C shall not exceed the specified value
c) Capacitance shall be within +10 %, -20 % of initial value
d) ESR shall not exceed 200 % of the specified value
Revision: 14-Mar-16
Document Number: 40137
3
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DLA 10004
www.vishay.com
Vishay
ENVIRONMENTAL CHARACTERISTICS
ITEM
CONDITION
COMMENTS
Seal
MIL-PRF-39006
When the capacitors are tested as specified in MIL-PRF-39006,
there shall be no evidence of leakage.
Moisture Resistance
MIL-PRF-39006
Moisture resistance shall be in accordance with MIL-PRF-39006.
Number of cycles: 10 continuous cycles
Barometric Pressure
(Reduced)
MIL-STD-202, method 105, condition E
Altitude 150 000 feet
MECHANICAL CHARACTERISTICS
ITEM
CONDITION
COMMENTS
Shock (Specified Pulse)
MIL-STD-202, method 213, condition I
(100 g)
The capacitors shall meet the requirements of MIL-PRF-39006.
Vibration, High Frequency
MIL-STD-202, method 204, condition D
(20 g peak)
The capacitors shall meet the requirements of MIL-PRF-39006.
Thermal Shock
MIL-STD-202, method 107, condition A
Thermal shock shall be in accordance with MIL-PRF-39006 when
tested for 30 cycles.
Solderability
MIL-STD-202, method 208,
ANSI/J-STD-002, test A
Solderability shall be in accordance with MIL-PRF-39006.
Terminal Strength
MIL-STD-202, method 211
Terminal strength shall be in accordance with MIL-PRF-39006.
Resistance to Solder Heat
MIL-STD-202, method 210, condition C
The capacitors shall meet the requirements of MIL-PRF-39006.
Terminals
MIL-STD-1276
Terminals shall be as specified in MIL-STD-1276. The length and
diameter of the terminals shall be as specified in Dimensions table.
All terminals shall be permanently secured internally and
externally, as applicable. All external joints shall be welded.
Marking
MIL-STD-1285
Marking of capacitors conforms to method I of MIL-STD-1285 and
include capacitance (in μF), capacitance tolerance letter, rated
voltage, date code, lot symbol and Vishay trademark.
SELECTOR GUIDES
Tantalum Selector Guide
www.vishay.com/doc?49054
Parameter Comparison Guide
www.vishay.com/doc?42088
Revision: 14-Mar-16
Document Number: 40137
4
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000