SIDACtor ® Protection Thyristors High Surge Current Protection SIDACtor® Primary Protection Balanced Series - Modified TO-220 Pb e3 RoHS Description The SIDACtor® Primary Protection Balanced Series Modified TO-220 are thyristor devices designed for use in primary protection applications. The series provides a single port overvoltage solution that enables applications to comply with the balance requirements of GR-974 and GTS-8700. Please contact Littelfuse to discuss your particular application and regulatory requirements. Features and Benefits Agency Approvals • High holding current options available Agency Agency File Number • Balanced overvoltage protection E133083 • Failsafe option available • Modified TO-220 Package • Low voltage overshoot • Lead forms available • Low on-state voltage • 2nd level interconnect is Pb-free per IPC/JEDEC J-STD-609A.01 Pinout Designation • Fails short circuit when surged in excess of ratings • Single-port protection • Does not degrade surge capability after multiple surge events within limit. Applicable Global Standards PIN 1 PIN 2 PIN 3 Schematic Symbol 1 • GR-974 • UL 497 • GTS-8700 • ITU K.28 3 (T) (R) 2 (G) Electrical Characteristics Part Number P1553ACLxx P1803ACLxx P2103ACLxx P2353ACLxx P2703ACLxx P3203ACLxx P3403ACLxx P5103ACLxx Marking P1553AC P1803AC P2103AC P2353AC P2703AC P3203AC P3403AC P5103AC VS VDRM @lDRM=5µA @100V/µs V min V max Pins 1-2, 3-2, 1-3 130 180 150 210 170 250 200 270 230 300 270 350 300 400 420 600 IH* IS IT VT@IT= 2.2 Amps mA min mA max A max V max 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 8 8 8 8 8 8 8 8 Notes: * Higher holding current available by special order. Contact Littelfuse for additional information. - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional (unless otherwise noted). © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/07/14 1 Capacitance Pin 1-2 / 3-2 Tip-Ground, Ring-Ground pF min 65 55 55 50 50 45 45 40 pF max 95 85 85 75 75 70 65 60 Pin 1-3 Tip-Ring pF min 40 35 30 30 30 25 25 20 pF max 60 55 55 50 50 45 45 40 - Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. - xx Part Number Suffix: ‘RP’ (Reel pack), Blank (Bulk pack), ‘60’ (Type 60 lead form bulk pack), ‘FS1’ (Failsafe option bulk pack). Refer to Part Numbering section for additional details. Primary Protection Balanced Series, Modified TO-220 SIDACtor ® Protection Thyristors High Surge Current Protection Surge Ratings Series IPP ITSM 50/60 Hz di/dt A min A min A/µs max 200 50 500 0.2x310 0.5x700 2 2x10 2x10 2 8x20 1.2x50 2 10x160 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 A min A min A min A min A min A min A min A min 50 500 400 200 150 200 175 100 1 C 1 1 1 Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP ratings applicable over temperature range of -40ºC to +85ºC - The device must initially be in thermal equilibrium with -40°C < TJ < +150°C 1 Current waveform in µs 2 Voltage waveform in µs Thermal Considerations Package Symbol Parameter Value Unit TJ Operating Junction Temperature Range -40 to +150 °C TS Storage Temperature Range -65 to +150 °C R0JA Thermal Resistance: Junction to Ambient 50 °C/W Modified TO-220 PIN 1 PIN 2 PIN 3 V-I Characteristics tr x td Pulse Waveform IPP – Peak Pulse Current – %IPP +I IT IS IH IDRM -V +V VT VDRM VS 100 Waveform = tr x td 50 0 -I td tr t – Time (µs) Normalized DC Holding Current vs. Case Temperature 10 IH 8 6 25 °C 4 2 IH (TC = 25ºC) 2.0 14 12 Ratio of Percent of VS Change – % Half Value 0 Normalized VS Change vs. Junction Temperature tr = rise time to peak value td = decay time to half value Peak Value 0 -4 -6 -8 -40 -20 0 20 40 60 1.6 1.4 25°C 1.2 1.0 0.8 0.6 0.4 80 100 120 140 160 -40 Junction Temperature (TJ) – °C © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/07/14 1.8 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC 2 Primary Protection Balanced Series, Modified TO-220 SIDACtor ® Protection Thyristors High Surge Current Protection Soldering Parameters Pb-Free assembly (see Fig. 1) +150°C +200°C 60-180 secs. - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)°C Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C Figure 1 TP Critical Zone TL to TP TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Physical Specifications Time Environmental Specifications Lead Material Copper Alloy Terminal Finish 100% Matte-Tin Plated Body Material tP Ramp-up Temperature Reflow Condition UL recognized epoxy meeting flammability classification 94V-0 Part Numbering P xxx 3 A C L xx PACKING OPTIONS TYPE Blank: Bulk RP: Reel Pack 60: Type 60 Lead Form (for type 60 orders, contact factory). P = SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE RoHS COMPLIANT PACKAGE TYPE IPP RATING High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Temp Cycling -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 High Temp Storage +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock 0°C to +100°C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A-102 Resistance to Solder Heat +260°C, 30 secs. MIL-STD-750 (Method 2031) Moisture Sensitivity Level 85%RH, +85°C, 168 hrs., 3 reflow cycles (+260°C Peak). JEDEC-J-STD-020, Level 1 Part Marking XXXXXXXXX P xxx 3 A C L FS1 TYPE FAILSAFE OPTION* MEDIAN VOLTAGE RoHS COMPLIANT xxxxx Part Marking Code (Refer to Electrical Characteristics Table) Date Code P = SIDACtor CONSTRUCTION VARIABLE PACKAGE TYPE IPP RATING * Failsafe devices are only offered in bulk pack, reel pack not available. © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/07/14 3 Primary Protection Balanced Series, Modified TO-220 SIDACtor ® Protection Thyristors High Surge Current Protection Dimensions - Modified TO-220 A Inches O D Temperature Measurement Point F G Dimensions - Modified TO-220 with Failsafe P PIN 3 PIN 2 PIN 1 L M K H N J The modified TO-220 package is designed to meet mechanical standards as set forth in JEDEC publication number 95. Millimeters Min Max Min A 0.400 0.410 10.16 10.42 Max D 0.360 0.375 9.14 9.53 F 0.110 0.130 2.80 3.30 G 0.540 0.575 13.71 14.61 H 0.025 0.035 0.63 J 0.195 0.205 4.95 5.21 K 0.095 0.105 2.41 2.67 0.89 L 0.060 0.075 1.52 1.90 M 0.070 0.085 1.78 2.16 N O P 0.018 0.024 0.46 0.61 0.178 0.290 0.188 0.310 4.52 7.37 4.78 7.87 Tape and Reel Specification - Modified TO-220 0.240 (6.10) Dimensions - Modified TO-220 Type 60 with Failsafe 0.019 (0.5) 1.626 (41.15) 0.750 ± 0.010 (19.05 ± 0.25) 0.720 (18.29) 0.360 (9.14) 0.500 (12.7) 0.100 (2.54) 0.100 (2.54) 14.173 (360.0) Dimensions are in inches (and millimeters). Direction of Feed 1.968 (50.0) Packing Options Package Type A Description Quantity Added Suffix Industry Standard Modified TO-220 Tape and Reel Pack 700 RP EIA-468-B Modified TO-220 Bulk Pack 500 (no added suffix) N/A Modified TO-220 Type 60 Lead Form Bulk Pack 500 60 (special order item, contact factory for details) N/A © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/07/14 4 Primary Protection Balanced Series, Modified TO-220