SIDACtor ® Protection Thyristors High Surge Current Protection High Surge Current Series - DO-214 Pb e3 RoHS Description The High Surge Current DO-214 Series are SIDACtor® thyristors designed to protect equipment located in hostile environments from overvoltage transients. The series provides a 200A 10/1000 μs rated surface mount solution that enables equipment to comply with enhanced surge requirments now specified in regulatory and customer requirements. Features and Benefits • Low voltage overshoot Rating • Low on-state voltage Agency Approvals Agency • Does not degrade surge capability after multiple surge events within limit. Agency File Number E133083 • Fails short circuit when surged in excess of ratings Pinout Designation • 200A 10x1000 Surge Not Applicable • 1000A 2x10 Surge Rating • RoHS Compliant and Halogen-Free • Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD609A.01) Applicable Global Standards Schematic Symbol • TIA-968-A • GR 1089 Intra-building • TIA-968-B • IEC 61000-4-5 2nd edition • ITU K.20/21/45 Enhanced Level • ITU K.20/21/45 Basic Level • YD/T 1082 • YD/T 993 • YD/T 950 • GR 1089 Inter-building Electrical Characteristics Part Number P0080SDLRP P0640SDLRP P0720SDLRP P0900SDLRP P1100SDLRP P1300SDLRP P1500SDLRP P1800SDLRP P2300SDLRP P2600SDLRP P3100SDLRP P3500SDLRP Marking P-8D P06D P07D P09D P11D P13D P15D P18D P23D P26D P31D P35D VDRM @lDRM=5µA VS @100V/µs V min V max 6 58 65 75 90 120 140 170 190 220 275 320 25 77 88 98 130 160 180 220 260 300 350 400 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Components are bi-directional (unless otherwise noted). ** Will meet 4.4A power cross requirement without fire hazard. © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/16/16 IH IS IT** mA min mA max A max 50 50 50 50 50 50 50 50 50 50 50 50 800 800 800 800 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 VT @IT=2.2A Capacitance @1MHz, 2V bias V max pf min pF max 4 4 4 4 4 4 4 4 4 4 4 4 50 100 100 95 75 65 60 50 50 50 45 45 150 160 150 140 115 100 90 90 80 75 70 65 SIDACtor ® Protection Thyristors High Surge Current Protection Series Surge Ratings D IPP ITSM 50/60 Hz di/dt A min A min A/µs max 350 50 1000 0.2/310 1 0.5/700 2 2/10 1 2/10 2 8/20 1 1.2/50 2 10/160 1 10/160 2 10/560 1 10/560 2 5/320 1 9/720 2 10/360 1 10/360 2 10/1000 1 10/1000 2 5/310 1 10/700 2 A min A min A min A min A min A min A min A min — 1000 800 — — — — 200 Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product that remains in thermal equilibrium. - IPP ratings applicable over temperature range of -40ºC to +85ºC - The component must initially be in thermal equilibrium with -40°C < TJ < +150°C 1 Current waveform in µs 2 Voltage waveform in µs Thermal Considerations Package DO-214AA Symbol Parameter Value Unit TJ Operating Junction Temperature Range -40 to +150 °C TS Storage Temperature Range -65 to +150 °C R0JA Thermal Resistance: Junction to Ambient 90 °C/W V-I Characteristics tr x td Pulse Waveform IT IS IH IDRM -V +V VT VDRM VS IPP – Peak Pulse Current – %IPP +I Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 td tr t – Time (µs) -I Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature IH 10 8 6 25 °C 4 IH (TC = 25ºC) 14 12 Ratio of Percent of VS Change – % 2.0 2 0 -4 -6 1.8 1.6 1.4 1.0 0.8 0.6 0.4 -8 -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) – °C 25°C 1.2 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/16/16 SIDACtor ® Protection Thyristors High Surge Current Protection Soldering Parameters Pb-Free assembly (see Fig. 1) +150°C +200°C 60-180 secs. - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)°C Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C Physical Specifications Figure 1 TP tP Critical Zone TL to TP Ramp-up Temperature Reflow Condition TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Environmental Specifications Lead Material Copper Alloy High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Terminal Finish 100% Matte-Tin Plated Temp Cycling -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Body Material UL Recognized epoxy meeting flammability classification V-0 per Underwriters Laboratories Biased Temp & Humidity 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 High Temp Storage +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock 0°C to +100°C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A-102 Resistance to Solder Heat +260°C, 30 secs. MIL-STD-750 (Method 2031) Moisture Sensitivity Level 85%RH, +85°C, 168 hrs., 3 reflow cycles (+260°C Peak). JEDEC-J-STD-020, Level 1 Part Numbering Part Marking P xxx 0 S DL RP TYPE P: SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE PACKAGE TYPE © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/16/16 REEL PACK RoHS COMPLIANT IPP RATING Pxxx xxxxx Part Marking Code (Refer to Electrical Characteristics Table) Date Code SIDACtor ® Protection Thyristors High Surge Current Protection Dimensions — DO-214AA Pad Outline Case Temperature Measurement Point B D 0.110 (2.8) C A 0.079 (2.0) H E inch (millimeter) F K G Packing Options Package Type S Dimensions 0.079 (2.0) Inches Min Max Min Max A 0.130 0.156 3.30 3.95 B 0.201 0.220 5.10 5.60 C 0.077 0.087 1.95 2.20 D 0.159 0.181 4.05 4.60 E 0.030 0.063 0.75 1.60 F 0.075 0.096 1.90 2.45 G 0.002 0.008 0.05 0.20 H 0.077 0.104 1.95 2.65 K 0.006 0.016 0.15 0.41 Tape and Reel Specification — DO-214AA Description Quantity Added Suffix Industry Standard DO-214AA Tape and Reel Pack 2500 RP EIA-481-D 0.157 (4.0) 0.472 (12.0) 0.36 (9.2) 0.315 (8.0) 0.059 DIA (1.5) 12.99 (330.0) Additional Information 0.512 (13.0) Arbor Hole Dia. 0.49 (12.4) Datasheet Millimeters Resources Cover tape Dimensions are in inches (and millimeters). Direction of Feed Samples © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/16/16